Sub-picosecond pulses at 100 W average power from a Yb:YLF chirped-pulse amplification system

We present a high-repetition-frequency, diode-pumped, and chirped-pulse amplification system operating at 106 W average output power with excellent beam quality (M(2)=1.3), based on cryogenically cooled Yb:YLF. 1 nJ seed pulses, derived from a mode-locked Ti:sapphire laser, are first amplified to 1 mJ pulse energy at 10 kHz repetition frequency in a regenerative amplifier. The second-stage, multipass amplifier increases the pulse energy to 10.6 mJ, resulting in a spectral width of 2.2 nm. The pulses are compressed to 865 fs in duration, which is 1.26 times the transform limit.     

Demonstration of a compact 100 Hz, 0.1 J, diode-pumped picosecond laser

We have demonstrated an all-diode-pumped Yb:YAG chirped pulse amplification laser that produces 100 mJ pulses of 5 ps duration at 100 Hz repetition rate. The compact laser system combines a room-temperature Yb:YAG regenerative amplifier for increased bandwidth and a cryogenically cooled Yb:YAG four-pass amplifier for improved heat dissipation and increased efficiency. The optical efficiency of this amplifier is higher than that of other diode-pumped systems of comparable energy.     

Multi-millijoule, nonlinear preamplifier for high intensity femtosecond Yb:YAG chirped-pulse amplification lasers at 1030 nm

We report the highest energy broadband laser pulses at a center wavelength of 1030 nm based on optical parametric chirped-pulse amplification (OPCPA). We have demonstrated amplification of 1030 nm femtosecond laser pulses from a broadband Yb oscillator to over 6.5 mJ with a total gain of greater than 10⁷ achieved in a single pass through only 56 mm of gain material at a 10 Hz repetition rate. The amplified spectral bandwidth of 10.8 nm affords recompression to a 230 fs pulse duration following amplification. As an alternative to the regenerative amplifier (RA) this system is one of the more promising candidates for realizing compact, high intensity, direct diode-pumped, high repetition rate femtosecond Yb:YAG chirped-pulse amplification (CPA) in laser systems.     

Hundred mJ, sub-picoseconds, high temporal contrast OPCPA/Yb:YAG ceramic thin disk hybrid laser system

The authors have demonstrated an optical parametric chirped-pulse amplification (OPCPA)/Yb:YAG ceramic thin disk hybrid laser system having hundred mJ level pulse energy sub-picosecond pulse duration with high temporal contrast. At an input chirped-pulse energy of 3.8?mJ from an OPCPA preamplifier an output energy of 130?mJ has been generated from multipass diode-pumped Yb:YAG ceramic thin disk amplifier. A recompressed pulse duration of 450?fs with a contrast level of less than 7.2×10^?9 at ?150?ps before the main pulse has been obtained. The contrast level is the highest value achieved in Yb:YAG chirped-pulse amplification (CPA) laser system at 100?mJ level.     

Direct amplification of ultrashort pulses in μ-pulling-down Yb:YAG single crystal fibers

We demonstrated that Yb:YAG single crystal fibers have a strong potential for the amplification of femtosecond pulses. Seeded by 230?fs pulses with an average power of 400?mW at 30?MHz delivered by a passively mode-locked Yb:KYW oscillator, the system produced 330?fs pulses with an average power of 12?W. This is the shortest pulse duration ever produced by an Yb:YAG amplifier. The gain in the single crystal fiber reached a value as high as 30 in a simple double-pass configuration.     

Compact diode-pumped 1.1 kW Yb:YAG Innoslab femtosecond amplifier

We demonstrate a compact diode-pumped Yb:KGW femtosecond oscillator-Yb:YAG Innoslab amplifier master oscillator power amplifier (MOPA) with nearly transform-limited 636 fs pulses at 620 W average output power, 20 MHz repetition rate, and beam quality of M(x)(2) = 1.43 and M(y)(2) = 1.35. By cascading two amplifiers, we attain an average output power of 1.1 kW, a peak power of 80 MW, and a 615 fs pulse width in a single linearly polarized beam. The power-scalable MOPA is operated at room temperature, and no chirped-pulse amplification technique is used.     

Single-frequency Yb:YAG non-planar ring oscillator fiber amplifier source at 1030 nm

We report on amplification of a single-frequency Yb:YAG non-planar ring oscillator using Yb-doped fibers. The amplifier system operated at 1030 nm with up to 18.7 W output power, 75% slope efficiency and an M²-value better than 1.1.     

Generation of 400 μW at 17.5 μm using a two-color Yb fiber chirped pulse amplifier

We have demonstrated the generation of 400 μW of power at ~18 μm by difference-frequency mixing the 1038 and 1105 nm from a two-color, chirped pulse amplification Yb fiber system. A two-color seed is selected from a continuum source and amplified to 300 mW of total power in a two-stage Yb fiber amplifier.     

Generation of 520 mW pulsed blue light by frequency doubling of an all-fiberized 978 nm Yb-doped fiber laser source

Pulsed blue light at 489 nm has been generated by second-harmonic-generation of a nanosecond pulsed master-oscillator power amplifier system based on a short Yb(3+) doped single-mode fiber amplifier at 978 nm and an external-cavity diode laser as seed source. The Yb(3+)-doped fiber was core-pumped by a W type Nd(3+) doped double-clad fiber laser operating on the transition near 930 nm ((4)F(3/2)→(4)I(9/2)). 520 mW of average power was generated at 489 nm using a periodically poled MgO:LiNbO(3), corresponding to a conversion efficiency of 34%.     

High-power optical parametric chirped-pulse amplifier system with a 1.55 microm signal and a 1.064 microm pump

We have designed and built a chirped-pulse parametric-amplifier system that utilizes a 10 Hz, 300 ps, Nd:YAG pump laser system; a 1.575 microm fiber oscillator and amplifier as the signal source; and rubidium titanyl phosphate and potassium titanyl arsenate nonlinear crystals. We obtained 260 fs, 30 mJ pulses centered at 1.550 microm, representing a gain of > 10(9) and a peak power of 100 GW. To our knowledge, these are the highest energy and peak power pulses ever produced in the 1.5-2.0 microm region     

High-energy diode-pumped picosecond regenerative amplification at 999 nm in wavelength with a cryogenically cooled Yb:LuLiF(4) crystal

A diode-pumped, cryogenically cooled Yb:LuLiF(4) regenerative amplifier has been developed for the first time to our knowledge. A chirped-seed pulse was amplified and compressed in the regenerative amplifier, simultaneously, which generated approximately 6 mJ, 13 ps pulses at 999 nm in wavelength without a pulse compressor. Simultaneous lasing at 999 and 1024 nm, respectively, was demonstrated, which could be used for different frequency generation in the terahertz region.     

60-W average power in 810-fs pulses from a thin-disk Yb:YAG laser

We demonstrate a passively mode-locked diode-pumped thin-disk Yb:YAG laser generating 810-fs pulses at 1030 nm with as much as 60 W of average output power (without using an amplifier). At a pulse repetition rate of 34.3 MHz, the pulse energy is 1.75 microJ and the peak power is as high as 1.9 MW. The beam quality is close to the diffraction limit, with M2 < 1.1.     

高功率宽带射频调制连续激光源

射频强度调制激光作为激光雷达系统的载波可以有效提高系统的抗干扰和抗散射能力,高功率宽带射频强度调制光源是实现高分辨率远距离探测的关键.本文采用在Nd:YAG激光器的耦合腔中插入一对四分之一波片的方法实现了频差调谐范围为30 MHz—1.5 GHz的双频激光输出,结合光纤振荡功率放大技术,将双频信号光功率放大为50 W.耦合腔双频种子源具有良好的功率和频率稳定性,输出功率为9.5 mW时,功率标准差为0.145 mW,稳定性为1.52%,输出双频激光的频差为250 MHz时,拍频的标准差为1.6144 MHz.种子光进行三级光纤功率放大,得到50 W双频激光输出.放大后的双频激光功率波动范围小于0.1 W,双频拍频的标准差为1.777 MHz,很好地保持了放大之前的功率稳定性和双频频差稳定性.     

Generation of high-contrast and high-intensity laser pulses using an OPCPA preamplifier in a double CPA, Ti:sapphire laser system

We demonstrate a high-contrast, high-intensity double chirped-pulse amplification (CPA) Ti:sapphire laser system using an optical parametric chirped-pulse (OPCPA) pre- amplifier. By injecting cleaned microjoule seed pulses into the OPCPA, a temporal contrast greater than 10¹⁰ within picosecond times before the main femtosecond pulse is demonstrated with an output pulse energy of 1.7 J and a pulse duration of 30 fs, corresponding to a peak power of 60 TW at a 10 Hz repetition rate. This system uses a cryogenically-cooled Ti:sapphire final amplifier and generates focused peak intensities in excess of 10²⁰ W/cm².     

High power Yb-fiber laser amplifier based on nonlinear chirped-pulse amplification at a repetition rate of 1 MHz

We report a high power fiber amplifier based on nonlinear chirped-pulse amplification(NCPA). To manage the nonlinearity,pulse shaping is introduced by self-phase modulation in the fiber stretcher with the help of spectral filtering. The third-order dispersion is compensated for by the nonlinear phase shift in the NCPA. With optimization, the system can output 382 fs pulse duration with 20 W average power at 1 MHz repetition rate. The long-term average power fluctuation is measured to be0.5% in 24 h, and the beam quality factor(M~2) is 1.25.     

Laser-diode-pumped Yb:YAG laser as a new pump source and its application to an Er3+, Yb3+-codoped high-output-power fiber amplifier

We propose a laser-diode-pumped Yb:YAG laser as a novel practical fiber amplifier pump source, and describe its first successful application of high-output-power operation (850 mW=+29.3 dB m) of an Er³⁺,Yb³⁺-codoped fiber amplifier at 1.55 μm. We have developed both bulk and microchip Yb:YAG lasers and obtained 3.3 W and 2.7 W, respectively, in the cw mode at room temperature. Laser-diode-pumped Yb:YAG lasers are shown to have a potential applicability to such fiber amplifiers as Pr³⁺-doped amplifiers and Tm³⁺-doped amplifiers, as well as Er³⁺,Yb³⁺-codoped fiber amplifiers. Received: 12 August 1999 / Revised version: 3 September 1999 / Published online: 20 October 1999     

Nd:YVO₄ amplifier for ultrafast low-power lasers

An Nd:YVO₄ amplifier consisting of two modules end pumped at 808?nm at 30?W total absorbed power has been designed for efficient, diffraction-limited amplification of ultrafast pulses from low-power seeders. We investigated amplification with a 50?mW, 7?ps Nd:YVO₄ oscillator, a 2?mW, 15?ps Yb fiber laser, and a 30?mW, 300?fs Nd:glass laser. Output power as high as 9.5?W with 8?ps pulses was achieved with the 250?MHz vanadate seeder, whereas the 20?MHz fiber laser was amplified to 6?W. The femtosecond seeder allowed extracting Fourier-limited 4?ps pulses at 7?W output power. To our knowledge, these are the shortest pulses from any Nd:YVO₄ laser device with at least 7?W output power. This suggests a novel approach to exploit the gain bandwidth of vanadate amplifiers with high output power levels. Such amplifier technology promises to offer an interesting alternative to high-power thin disk oscillators at few picoseconds duration, as well as to regenerative amplifiers with low-repetition-rate fiber seeders.     

High-power polycrystalline Er:YAG ceramic laser at 1617 nm

We report on the efficient operation of a high-power erbium-doped polycrystalline Er:YAG ceramic laser at 1617 nm resonantly pumped by a high-power 1532 nm Er,Yb fiber laser. Lasing characteristics of Er:YAG ceramics with different Er3+ concentrations are evaluated and compared. With an output coupler of 15% transmission and 0.5 at. % Er3+-doped YAG ceramic as the gain media, the laser generates 14 W of output power at 1617 nm for 28.8 W of incident pump power at 1532 nm, corresponding to a slope efficiency with respect to incident pump power of 51.7%.     

基于光纤拉曼放大的级联式全光纤1020nm光源

设计并制作了输出功率为196 mW的级联式全光纤1020 nm光源.该光源采用光纤拉曼放大器与掺镜光纤放大器级联的放大方案,实现了对低功率1020 nm种子光的放大.在光纤拉曼放大级,采用了3段不同长度的拉曼增益光纤进行了对比实验,比较了一定信号光功率和抽运光功率下拉曼增益光纤长度对光纤拉曼放大级输出功率的影响;测量了...     

High-energy, high-contrast, multiterawatt laser pulses by optical parametric chirped-pulse amplification

We describe a compact, reliable, high-power, and high-contrast noncollinear optical parametric chirped-pulse amplifier system. With a broadband Ti:sapphire oscillator and grating-based stretching and compression, the chirped pulses are amplified from 0.1 nJ to 122 mJ in type I beta-barium borate optical parametric chirped-pulse amplifiers with a total gain of over 10(9) at 10 Hz repetition rate. Pulse compression down to 19-fs duration achieved after amplification indicates a peak power of 3.2 TW at an average power of 0.62 W. The prepulse contrast is measured to be less than 10(-8) on picosecond time scales.