金属离子与卟啉的嵌入反应动力学研究──Ⅶ．一元酸根催化Cu(Ⅱ)与溴化间－四(N－乙酸甲酯基－3－吡啶基)卟啉的配位反应

研究了在３５±０．１℃、离子强度０．５ｍｏｌ／Ｌ（ＫＣｌ）条件下，甲酸根、乙酸根、丙酸根和丁酸根分别催化Ｃｕ（Ⅱ）离子与四溴化间－四（Ｎ－乙酸甲酯基－３－吡啶基）卟啉（Ｈ２Ｔβ－Ｎ－ＡＣＭｓｐｙＰＢｒ４）的反应动力学及其机理，该类反应对卟啉和Ｃｕ（Ⅱ）离子均为一级反应，反应动力学方程为：ｄ［ＣｕＰ＾４＋］／ｄｔ＝ｋ｛１．０＋ｂ［Ａ＾－］）／（１．０＋Ｋ３，４．［Ｈ＾＋］＾２｝［Ｃｕ＾２＋］［Ｐ］Ｔ     

丁基罗丹明B—钼酸盐光度法连续测定铈和钪

在聚乙烯醇（ＰＶＡ）存在下，丁基罗丹明Ｂ（ＢＲＢ）分别与铈钼、钪钼杂多酸络阴离子形成离子缔合物，其最大吸收均位于５７０ｎｍ，表面摩尔吸光度分别为εＣｅ＝３．９６×１０＾６Ｌ．ｍｏｌ＾－１．ｃｍ＾－１，εＳｃ＝４．７１×１０＾５Ｌ．ｍｏｌ＾－１．ｃｍ＾－１，服从比耳定律范围分别为０－２４μｇ／Ｌ Ｃｅ和０－６０μｇ／ＬＳｃ，测定极限为Ｃｅ１．０μｇ／Ｌ（ｎ＝１２）和Ｓｃ１．９μｇ／Ｌ（ｎ＝１０），对     

铽-环丙沙星体系的荧光特性及环丙沙星的测定

近中性条件下,铽（Ⅲ）能与环丙沙星（ｃｉｐｒｏｆｌｏｘａｃｉｎ）反应形成１：２的络合物。利用这一反应,建立了简单、快速、灵敏的测定环丙沙星的荧光方法,并且详细讨论了测定的各种条件。测定的最佳条件为：λｅｘ／λｅｍ＝３２５．０／５４５／０ｎｍ,Ｔｂ＾３＋（３．０＊１０－３ｍｏｌ／Ｌ）２．０ｍＬ,ｐＨ＝６．０的ＮａＡｃ－ＨＡｃ缓冲溶液２．０ｍＬ。线性范围１３－１０００μｇ／Ｌ,回归方程为Ｆ＝５．４２＋０．２２０７μｇ／Ｌ）（ｒ＝０．９９８）;检出限为１０μｇ／Ｌ。此方法用于血清及环丙沙星片剂的测定,结果令人满意。     

水杨醛缩—5—碘—5—氨基喹啉的合成及荧光光度法测定煤渣中痕量镓的研究

报道了新息夫碱试剂水杨醛缩－５－碘－５－氨基喹啉（ＳＡＩＡＱ）的合成。用元素分析、红外光谱法确定了其结构。测定了ＳＡＩＡＱ的酸度常数Ｋａ１＝２．４０×１０＾－４，Ｋａ２＝２．９８×１０＾－９。在ｐＨ３．５０￣５．００范围内ＳＡＩＡＱ与Ｇａ＾３＋形成稳定的荧光螯合物，且在λｅｘ／λｅｍ＝４２８ｎｍ／５４０ｎｍ产生强烈荧光。其荧光强度与Ｇａ＾３＋的浓度在１．５μｇ／Ｌ￣２６０μｇ／Ｌ范围内呈线性关系，     

新试剂N—间甲苯基—N′—（氨基对苯磺酸钠）硫脲（MMPT）的合成及其在…

本文合成新试剂Ｎ－间甲苯基－Ｎ′－（氨基对苯磺酸钠）硫脲（ＭＭＰＴ）经红外，紫外，核磁，元素分析等测试，确定其结构，研究测定了试剂与４０多种种离子的反应及其配合物的表观洋吸光系数，它可作为Ｃｕ＾２＋（ｍ＝０．０１５μｇ，ｃ＝０．５μｇ／ｍＬ），Ａｇ＾＋（ｍ＝０．１μｇ，ｃ＝３．３μｇ／ｍＬ）的新鉴定试剂和光度法测定Ｐｄ＾２＋（ε３０９．７＝６．３２×１０＾４Ｌ．ｍｏｌ＾－１．ｃｍ＾－１，Ｐｔ（Ⅳ）     

用金钨杂多酸和耐尔蓝光度法测定纳克量金

在阿拉伯胶存在下，金与钨酸钠和耐尔蓝（ＮＢ）形成离子缔合物，它的最大吸收位于５８０ｎｍ，表观摩尔吸光系数ε值为２．３８×１０＾７Ｌ·ｍｏｌ＾－１·ｃｍ＾－１，体系至少稳定２４ｈ。金量在０￣４．４μｇ／Ｌ范围内服从比尔定律，检测限（３σ）为０．０６９μｇ／Ｌ（ｎ＝１２），对４．０μｇ／Ｌ Ａｕ（Ⅲ）测定的相对标准偏差为１．９％（ｎ＝１１），离子缔合物的摩尔比为Ａｕ（Ⅲ）：ＮＢ＝１：３。考察了４０多种     

桑色素光度法测定痕量铝和聚丙烯酰胺

基于聚丙烯酰胺（ＰＡＭ）作为增稳剂时,Ａｌ＾３＋叠色素（ｍｏｒｉｎ）之间的显色反应,提出了一种简便,快速,高灵敏测定痕量铝的光度法,络合物组成比为Ａｌ：ｍｏｒｉｎ＝１：２;表观摩尔吸光系数ε４０８＝６．３×１０＾７Ｌ．ｍｏｌ＾－１．ｃｍ＾－１;铝浓度在０．０４－０．２８μｇ／Ｌ范围内服从比尔定律;检测限４．０×１０＾－１０ｇ／Ｌ。     

催化动力学垂直光路光度法测定痕量铜

建立了痕量铜的催化动力学垂直光路光度测定法，铜含量在０～３．０ｎｇ／２５０μｌ范围内符合比耳定律，工作曲线的回归方程为：△Ａ＝０．５３４Ｃ（ｃｕ＾２＋，ｎｇ），＋０．０１８（ｒ＝０．９９９９），检出限为１．５×１０＾－１１ｇ．ｍｌ＾－１（△Ａ＝０．０２，ｔ＝２ｍｉｎ）由曲线斜率法求得的表观摩尔吸光系数为１．２×１０＾７，方法用于氮三乙酸及标准水样中铜的测定，加标回收率在９２％～９８％，相对标准偏差     

乙基罗丹明B和高碘酸钾反应动力学测定痕量铑

研究了一个动力学测定铑的方法。在氯化钠－磷酸溶液和加热下铑催化乙基罗丹有Ｂ褪色,１ｇ（Ａ０／Ａ）与铑浓度呈线性的范围是０．２－４．０μｇ／２５ｍＬ,检出限为２．２４×１０＾－１０ｇ／ｍＬ,对２．０μｇ铑标准溶液测定１１次的相对标准偏差为２．１３％。     

催化动力学光度法测定痕量苯酚

研究了在硫酸介质中苯酚对Ｉ＾－１催化Ｃｅ＾４＋－Ａｓ（Ⅲ）反应的抑制作用及其动力学条件。建立了用催化动力这光度法测定痕量苯酚的新方法，结果表明，在０．００１ｍｏｌ／ＬＣｅ（ＳＯ４）２，０．００１２５ｍｏｌ／Ｌ，Ａｓ２Ｏ３，０．０１ｍｇ／Ｌ，ＫＩ，０．０１２５ｍｏｌ／Ｌ，Ｈ２ＳＯ４和０．１３％（ｗ／ｖ）ＮａＣｌ溶液中测定苯酚，其表面摩尔吸光系数为２．１×１０＾５Ｌ．ｍｏｌ＾－１．ｃｍ＾－１，线性范围     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。     

Determination of heats of detonation and influence of components of composite explosives on heats of detonation of high explosives

The heats of detonation of 20 simple high explosives and explosive mixtures were determined by means of an adiabatic detonation calorimeter designed by the authors. The results indicated that the performance of the instrument was reliable and the experimental data were very accurate. For explosive mixtures, there was a linear accumulative relationship between the heats of detonation of the explosive mixture and its components. Accordingly, the heats of detonation of explosive mixtures could be calculated directly from the heats of detonation of simple explosives and the characteristic heats of other components. The experiments showed that the gold or brass shell of the cylindrical charge could be substituted by a thick-walled porcelain shell, which had the advantage of cheapness.

     

Synthesis of phenolic components of Grains of Paradise

Two vanilloids, (5E)-8-(4-hydroxy-3-methoxyphenyl)oct-5-en-4-one (1) and 4-[3-hydroxydecyl]-2-methoxyphenol (2), isolated from the dried seeds of Grains of Paradise (Aframomum melegueta), were synthesized; the latter compound was made as the S-enantiomer and the material derived from the seeds was found to be a 1:1.7 mixture of the R and S isomers. The synthetic route used should allow the preparation of analogs having extended alkyl chains and consequently different lipophilicity, and 3, a homolog of 2, was also prepared.     

Summary of development of the theory of stability of colloids and thin films

In this review, the research of the author in the field of colloidal systems is summarized. The factors influencing colloidal stability are systematized and analyzed. Examples are presented to illustrate the practical utilization of the theory of stability of colloids and thin films.This review was prepared on the basis of the works of the author, which were awarded the State Premium for 1991 in the field of science and technology, chemistry section.Institute of Physical Chemistry, Russian Academy of Sciences, 117915 Moscow. Translated from Izvestiya Akademii Nauk, Seriya Khimicheskaya, No. 8, pp. 1708–1717, August, 1992.     

Study of hydration of two cements of different strengths

Main hydration products of two cement pastes, i.e. CSH-gel, portlandite (P) (and specific surface S) were studied by static heating, and by SEM, TEM and XRD, as a function of cement strength (C-33 and C-43) hydration time (th) and subsequent hydration in water vapour.Total change in mass on hydration and air drying, M_o, increased with strength of cement paste and with hydration time. Content of water escaping at 110 to 220°C, defined as water bound with low energy, mainly interlayer and hydrate water, was independent on cement strength but its content increased with (th). Content of chemically bound (zeolitic) water in CSH-gel, escaping at 220-400°C, was slightly dependent on strength and increased with (th). It was possibly derived from the dehydroxylation of CSH-gel and AFm phase. Portlandite water, escaping at 400-500°C, was independent on cement strength and was higher on longer hydration. Large P crystals were formed in the weaker cement paste C-33. Smaller crystals were formed in C-43 but they increased with (th). Carbonate formated on contact with air (calcite, vaterite and aragonite), decomposed in cement at 600-700^oC. It was high in pastes C-33(1 month) and C-43(1 month), i.e. 5.7 and 3.3%, respectively; it was less than 1% after 6 hydration months (low sensitivity to carbonation) in agreement with the XRD study showing carbonates in the air dry paste (1month), and its absence on prolonged hydration (6 months) and on acetone treatment. Water vapour treatment of (6 months) pastes or wetting-drying increased this sensitivity.Nanosized P-crystals, detected by TEM, could contribute to the cement strength; carbonate was observed on the rims of gel clusters.This revised version was published online in November 2005 with corrections to the Cover Date.     

氯氧化镁生成热的研究

用氧化镁氯化镁水溶液制备了8水合氯氧化镁[nMg(OH)2·MgCl2·8H2O], 并测定了其在盐酸中的溶解热, 实验结果表明, 氯氧化镁溶解热与n值呈线性关系, 根据溶解热求出5Mg(OH)2·MgCl2·8H2O和3Mg(OH)2·MgCl2·8H2O的生成热分别为-7727.1和5888.1kJ·mol^1^-。     

Thermodynamics of the formation of oxosulfides of rare-earth elements

The enthalpies of solution of several oxosulfides of rare-earth elements and the high-temperature enthalpies of oxosulfides and oxosulfates of lanthanum and yttrium were measured using solution calorimetry and high-temperature microcalorimetry techniques. Standard enthalpies of formation and some thermodynamic properties of oxosulfides and oxosulfates were calculated. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 2 pp. 294–297, February, 1997.     

探究“铁的锈蚀条件”实验创新设计

设计了铁的锈蚀实验,说明了铁钉的处理方法,增加了温度、酸、碱的影响条件,实现了铁跟蒸馏水及空气中氧气快速反应而生锈,使实验在5 min左右就能够得到准确的结果。