Nanostructure and properties of polysiloxane‐layered silicate nanocomposites

The relationship between nanostructure and properties in polysiloxane layered silicate nanocomposites is presented. Solvent uptake (swelling) in dispersed nanocomposites was dramatically decreased as compared to conventional composites, though intercalated nanocomposites and immiscible hybrids exhibited more conventional behavior. The swelling behavior is correlated to the amount of bound polymer (bound rubber) in the nanocomposites. Thermal analysis of the bound polymer chains showed an increase and broadening of the glass‐transition temperature and loss of the crystallization transition. Both modulus and solvent uptake could be related to the amount of bound polymer formed in the system. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 1595–1604, 2000     

Investigating the effect of nanolayered silicates on blend segmental dynamics and minor component relaxation behavior in poly(ethylene oxide)/poly(methyl methacrylate) miscible blends

Polymer–silicate nanocomposites based on poly (ethylene oxide), PEO, poly(methyl methacrylate), PMMA, and sodium montmorillonite clay were fabricated and characterized to investigate the effect of nanolayered silicates on segmental dynamics of PEO/PMMA blends. X‐ray results indicate the formation of an exfoliated morphology in the nanocomposites. At low silicate contents, an enhancement in segmental dynamics of blend nanocomposites and also PEO, minor component in blend, is observed at temperature region below blend glass transition. This result can be attributed to the improvement of the confinement effect of rigid PMMA matrix on the PEO chains by introducing a low amount of layered silicates. On the other hand, at high silicate contents, an enhancement in segmental dynamics of blend nanocomposites and PEO is observed at temperature region above blend glass transition. This behavior could be interpreted based on the reduction of monomeric friction between two polymer components, which can facilitate segmental motions of blend components in nanocomposite systems. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

Quasielastic neutron scattering of poly(methyl phenyl siloxane) in the bulk and under severe confinement

Quasielastic neutron scattering was utilized to investigate the influence of confinement on polymer dynamics. Poly(methyl phenyl siloxane) chains were studied in the bulk as well as severely confined within the approximately 1-2 nm interlayer spacing of intercalated polymer/layered organosilicate nanohybrids. The temperature dependence of the energy resolved elastic scattering measurements for the homopolymer and the nanocomposites exhibit two distinct relaxation steps: one due to the methyl group rotation and one that corresponds to the phenyl ring flip and the segmental motion. Quasielastic incoherent measurements show that the very local process of methyl rotation is insensitive to the polymer glass transition temperature and exhibits a wave-vector independent relaxation time and a low activation energy, whereas it is not affected at all by the confinement. At temperatures just above the calorimetric glass transition temperature, the observed motion is the phenyl ring motion, whereas the segmental motion is clearly identified for temperatures about 60 K higher than the glass transition temperature. For the nanohybrid, the segmental motion is found to be strongly coupled to the motion of the surfactant chains for temperatures above the calorimetric glass transition temperature of the bulk polymer. However, the mean square displacement data show that the segmental motion in confinement is faster than that of the bulk polymer even after the contribution of the surfactant chains is taken into consideration.     

Glass transition broadening via nanofiller-contiguous polymer network in aromatic thermosetting copolyester nanocomposites

The glass transition is a genuine imprint of temperature-dependent structural relaxation dynamics of backbone chains in amorphous polymers, which can also reflect features of chemical transformations induced in macromolecular architectures. Optimization of thermophysical properties of polymer nanocomposites beyond the state of the art is contingent on strong interfacial bonding between nanofiller particles and host polymer matrix chains that accordingly modifies glass transition characteristics. Contemporary polymer nanocomposite configurations have demonstrated only marginal glass transition temperature shifts utilizing conventional polymer matrix and functionalized nanofiller combinations. We present nanofiller-contiguous polymer network with aromatic thermosetting copolyester nanocomposites in which carbon nanofillers covalently conjugate with cure advancing crosslinked backbone chains through functional end-groups of constituent precursor oligomers upon an in situ polymerization reaction. Via thoroughly transformed backbone chain configuration, the polymer nanocomposites demonstrate unprecedented glass transition peak broadening by about 100 °C along with significant temperature upshift of around 80 °C. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2018 , 56, 1595–1603     

Influence of interaction between poly(methyl methacrylate) and clay on the properties of nanocomposites prepared by a heterocoagulation method

To have a better insight into the effect of interaction between polymer matrix and clay on the properties of nanocomposite, poly(methyl methacrylate)/clay nanocomposites were prepared by a heterocoagulation method. Using a reactive cationic emulsifier, methacryloyloxyethyltrimethyl ammonium chloride (METAC), a strong polymer–clay interaction was obtained with the advantage of keeping a consistent polymer matrix property. X‐ray diffraction and transmission electronic microscopy indicated an exfoliated structure in nanocomposites. The glass transition temperature (T_g) of the nanocomposites was measured by DSC and DMA. The DMA results showed that with a strong interaction, PMMA–METAC nanocomposite showed a 20 °C enhancement in glass transition temperature (T_g), whereas a slight increase in T_g was observed for PMMA–cetyl trimethylammonium bromide (CTAB)/clay nanocomposite with a weak interaction. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 733–738, 2010     

Synthesis and characterization of poly(methylmethacrylate)/silica nanocomposites: Study of the interphase by solid‐state NMR and structure/properties relationships

Organic/inorganic nanocomposites were synthesized from poly(methylmethacrylate) (PMMA) and properly modified silica nanoparticles by in situ polymerization. Methacryloylpropyltrimethoxysilane was selected as nanoparticle surface modifier because it is characterized by unsaturated end groups available to radical reactions, making possible to suppose their participation in the acrylic monomer polymerization. As a result of the above hypothesized reactions, a phase constituted by polyacrylic chains grafted onto modified silica surface was isolated. ²⁹Si and ¹³C solid‐state nuclear magnetic resonance experiments permitted to analyze this phase in terms of composition and chain mobility as well as to highlight interaction mechanisms occurring between growing PMMA oligoradicals and functional groups onto silica surface. It was demonstrated that this PMMA grafted onto silica surface acts as an effective coupling agent and assures a good dispersion of nanoparticles as well as a strong nanoparticle/matrix interfacial adhesion. As a result of strong interactions occurring between phases, a significant increase of the glass transition temperature was recorded. Finally, the abrasion resistance of PMMA in the hybrids was significantly improved as a result of a different abrasion propagation mechanism induced by silica particles thus overcoming one of the most serious PMMA drawback. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Copolyester/layered silicate nanocomposites: The effect of the molecular size and molecular structure of the intercalant on the structure and viscoelastic properties of the nanocomposites

The preparation of poly(ethylene glycol‐co‐cyclohexane‐1,4‐dimethanol terephthalate)/layered silicate nanocomposites via a melt‐intercalation technique is reported. Layered silicates modified with different alkyl ammonium intercalants have been used for this purpose. A comparison is made between carefully chosen pairs of the nanocomposites, the choice depending on the cation‐exchange capacity or the intercalant concentration of the organically modified montmorillonite, to study the effects of the molecular size and molecular structure of the intercalant. The structure of the nanocomposites is characterized with wide‐angle X‐ray diffraction. The presence of well‐defined diffraction peaks and an observed increase in the interlayer spacing in the nanocomposites imply the formation of an intercalated hybrid. To investigate the viscoelastic behavior, these nanocomposites are also subjected to dynamic mechanical analysis. The dynamic mechanical properties show an increase in the storage modulus of the nanocomposites over the entire temperature range studied (except in the transition region from 68 to 78 °C) in comparison with that of the pristine polymer. The size of the intercalant molecule and the presence of functional groups capable of forming favorable interactions with the polymer govern the amount of polymer infiltrating the clay gallery space and control the increase in the modulus of the nanocomposite. The tan δ peak signifying the glass‐transition temperature shifts to lower temperatures in the nanocomposites. Interestingly, the nanocomposites show less damping than the pristine polymer. This behavior is understood in terms of the confinement of the polymer chains in the clay interlayer. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 3102–3113, 2003     

Chain confinement in polymer nanocomposites and its effect on polymer bulk properties

The issue of chain confinement in nanocomposites remains largely unanswered because experimental systems are plagued by additional complicating variables such as particle–polymer interactions and free volume increases brought upon by the addition of the particles. Using computer simulation of high length chain polymers, we show that simple excluded volume interactions between polymer and nanoparticles lead to a wealth of changes in the diffusion coefficient and entanglement density of the chains. This opens up the possibility of using nanoparticles for tuning polymer properties, such as toughness, melt viscosity, and transient rubberlike behavior. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 687–692, 2010     

Characteristics of proton conducting polymer electrolyte based on chitosan acetate complexed with CH3COONH4

The polymer electrolytes based on chitosan and ammonium acetate (CH₃COONH₄) were prepared by solution casting technique and the properties were studied. With the addition of CH₃COONH₄, the amorphous nature of the polymer electrolytes was promoted. The glass transition temperature, activation energy, and conductivity are closely related. Lower the glass transition temperature, lower the activation energy, higher the conductivity. The 40 wt % ammonium acetate doped polymer electrolyte has the lowest glass transition temperature of 369 K, the lowest activation energy of 0.19 eV, and the highest ionic conductivity of 2.87 × 10^?4 S cm^?1 at room temperature. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 549–554, 2009     

Measurement of size‐dependent glass transition temperature in electrospun polymer fibers using AFM nanomechanical testing

The glass transition temperature (T_g) of individual electrospun polymer polyvinyl alcohol fibers of varying diameter was measured using atomic force microscopy (AFM) based nanomechanical thermal analysis. Indentation and bending of individual electrospun fibers using AFM allowed the calculation of the elastic modulus of the polyvinyl alcohol (PVA) fibers across a range of different temperatures. The elastic modulus of electrospun PVA fibers was observed to decrease significantly when passing through T_g, which allowed accurate determination of T_g. The T_g of electrospun PVA fibers was shown to decrease for smaller fiber diameters especially for fiber diameters below 250 nm. This size‐dependent glass transition behavior of electrospun PVA fibers is indicated as being due to polymer chain confinement. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

Synthesis and performance of proton conducting chitosan/NH4Cl electrolyte

The polymer electrolytes based on chitosan and ammonium chloride were prepared by solution casting technique and the properties were studied. The addition of ammonium chloride results in: (1) the enhancement of the amorphous nature of the polymer electrolytes; (2) the shift of the absorption bands of amino group at 1566 cm^?1 and the carbonyl group at 1640 cm^?1 towards lower wave number, and the appearance of a new absorption band at 1759 cm^?1; (3) a decrease of the glass transition temperature. The 20 wt % ammonium chloride doped polymer electrolyte has the best room temperature electric property, the lowest activation energy and the highest ionic conductivity. Placing the as‐prepared polymer electrolyte in a dryer is adverse for the sample's moisture content, and results in higher activation energy and lower ionic conductivity. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 260–266, 2010     

Synthesis of networked polymers with lithium counter cations from a difunctional epoxide containing poly(ethylene glycol) and an epoxide monomer carrying a lithium sulfonate salt moiety

Poly(ethylene glycol)‐based networked polymers that had lithium sulfonate salt structures on the network were prepared by heating a mixture of poly(ethylene glycol) diglycidyl ether (PEGGE), poly(ethylene glycol) bis(3‐aminopropyl) terminated (PEGBA), and an ionic epoxy monomer, lithium 3‐glycidyloxypropanesulfonate (LiGPS). Flexible self‐standing networked polymer films showed high thermal stability, low crystallinity, low glass transition temperature, and good mechanical strength. The materials were ion conductive at room temperature even under a dry condition, although the ionic conductivity was rather low (10^?6 to 10^?5 S/m). The ionic conductivity increased with the increase in temperature to above 1 × 10^?4 S/m at 90 °C. The film samples became swollen by immersing in propylene carbonate (PC) or PC solution of lithium bis(trifluoromethanesulfonyl)imide (LiTFSI). The samples swollen in PC showed higher ionic conductivity (ca.1 × 10^?3 S/m at room temperature), and the samples swollen in LiTFSI/PC showed much higher ionic conductivity (nearly 1 S/m at room temperature). © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 3113–3118, 2010     

Computational synthesis,structure, and glass transition of (1,4) Cis‐polyisoprene‐based nanocomposite by multiscale modeling

The main goal of the present study was to produce insights from the atomistic modeling into the structural changes in elastomer‐based polymer nanocomposites caused by the surface modifications of the filler particles, and by the crosslinking of the participating polymer matrix. The fully atomistic molecular‐dynamics computer simulations of crosslinked (1,4) cis‐polyisoprene (PI) films capped by amorphous silica substrates was set‐up, in the presence of realistic coupling and covering agents. The PI film stratified structure has been studied in the proximity of the corresponding glass transition, by varying the degree of crosslinking and the PI film thickness. Some monomer ordering induced by the pristine (bare) silica disappeared almost completely in films with modified surfaces. The average monomer density increased with degree of crosslinking. As compared with PI bulk, the glass‐transition temperature was slightly larger for highly crosslinked PI films with bare silica and surfaces with coupling agents, and increased with increasing confinement. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 473–485     

Mechanical and viscoelastic properties of confined amorphous polymers

Confinement of polymers to nanoscale dimensions can dramatically impact their physical properties. Substantial efforts have focused on the glass transition temperature (T_g) of polymers confined to thin films, but their mechanical properties are less studied despite their technological importance. In this review, challenges with mechanical measurements of polymer thin films are discussed along with novel metrologies that provide insight into their mechanical properties. A comparison of experimental measurements, simulations and theory provide several general conclusions about the mechanical properties under confinement. Confinement impacts the elastic modulus, rubbery compliance and viscosity of polystyrene, the archetypal polymer for confinement, but the confinement effect appears to depend on the measurement technique. This effect may be due to the details of averaging of gradients in properties that are dependent on the measurement details. Routes to minimize confinement effects are addressed. Despite progress in the measurements of mechanical properties of polymer thin films, there remain unresolved questions about the impact of confinement, which we highlight at the end of this review. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2018 , 56, 9–30     

Investigating the structure–property relationship of aromatic–aliphatic polyamide/layered silicate hybrid films

Surface treated montmorillonite was used to prepare nanocomposites with aromatic–aliphatic polyamide by solution intercalation technique. The polyamide chains were produced through polycondensation of 4-aminophenyl sulfone with sebacoyl chloride in dimethyl acetamide. Compatibility between the polymer and organoclay was achieved through carbonyl chloride end-capped amide chains prepared by adding extra sebacoyl chloride near the end of polymerization reaction. The nanocomposites morphology and clay dispersion were investigated by X-ray diffraction (XRD) and transmission electron microscopy (TEM). Delaminated and intercalated morphologies were observed for different loading of organoclay. Tensile strength and modulus improved for nanocomposites with optimum organoclay content (10-wt.%). Thermal stability and glass transition temperature of nanocomposites increased relative to pristine polyamide with augmenting organoclay content. Water uptake of these materials decreased as compared to the neat polyamide indicating reduced permeability.     

Preparation and properties of conductive silver/photosensitive polyimide nanocomposites

A new electrically conductive photoresist has been developed. It is based on the dispersion of silver nanoflakes in a negative‐tone photosensitive polyimide (PSPI) precursor. 2‐Mercaptopropionic acid was used as the surfactant to modify the silver nanoflake surface for the dispersion of silver nanoflakes in the polymer. The silver/PSPI nanocomposites showed electrical conductivity at a low silver content of 10 wt %. The electrical conductivity of the silver/PSPI nanocomposites ranged from 10 to 10⁴ S/cm, which was dependent on the silver weight fraction in the resist formulation. Patterns with a resolution of 30 μm were obtained from the silver/PSPI nanocomposites. The silver/PSPI nanocomposites had excellent thermal properties. Their glass transition temperatures were above 360 °C and thermal decomposition temperatures were over 420 °C. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 1575–1583, 2009     

Broadband Dielectric Relaxation Spectroscopy in Polymer Nanocomposites

Summary: Dielectric spectroscopy in the frequency domain and thermally stimulated depolarization currents techniques, covering together a broad frequency range (10⁻⁴–10⁹ Hz), were employed to investigate molecular dynamics in relation to structure and morphology in polymeric nanocomposites. Several systems were investigated, three of them with the same epoxy resin matrix and different inclusions (modified smectite clay, conducting carbon nanoparticles and diamond nanoparticles) and two with silica nanofiller (styrene-butadiene rubber/silica and polyimide/silica nanocomposites). Special attention was paid to the investigation of segmental dynamics associated with the glass transition of the polymer matrix, in combination also with differential scanning calorimetry measurements. Effects of nanoparticles on local (secondary) relaxations and on the overall dielectric behavior were, however, also investigated. Several interesting results were obtained and discussed for each of the particular systems. Two opposite effects seem to be common to the nanocomposites studied and dominate their behavior: (1) immobilization/reduction of mobility of a fraction of the chains at the interface to the inorganic nanoparticles, due to chemical or physical bonds with the particles, and (2) loosened molecular packing of the chains, due to tethering and geometrical confinement, resulting in an increase of free volume and of molecular mobility.     

Thermal and electrical behaviors of acid functionalized MWCNT/ABC-type triblock copolymer grafted-MWCNT nanocomposites

In this work, ABC-type triblock copolymer grafted onto the surface of the MWCNT/acid functionalized MWCNT (MWCNT-COOH) composites were prepared and the properties of nanocomposites were characterized extensively using differential scanning calorimetry (DSC), scanning electronic microscopy (SEM), thermogravimetric analysis (TGA), ac electrical conductivity and dielectrical measurements.

DSC study showed that the glass transition temperatures of the nanocomposites are a some higher than that of the matrix polymer. The increase in oxidized MWCNT in the nanocomposite improved the thermal stability of the composite, according to initial decomposition temperatures. The ac electrical conductivity has increased moderately with increasing frequency, but has increased slowly with increase in the oxidized MWCNT content in the nanocomposites. The electrical conductivity increases slowly with increasing temperature to about the glass transition temperature, then it increases faster. The dielectric constants for the matrix polymer and all the composites decreases slightly with increasing frequency from 0.1 kHz to 2.0 kHz. The dielectric constant increases slightly with increasing temperature up to about the glass transition temperature region and then the increase in temperature is accelerated the increase in the dielectric constant.     

Electrochromic material containing unsymmetrical substituted N,N,N′,N′‐tetraaryl‐1,4‐phenylenediamine: Synthesis and their optical,electrochemical, and electrochromic properties

A novel dibromo compound containing unsymmetrical substituted bi‐triarylamine was synthesized. A conjugated polymer was prepared via the Suzuki coupling from the newly prepared dibromo compound and 9,9‐dioctylfluorene‐2,7‐bis(trimethyleneboronate). The glass transition temperature (T_g) of the conjugated polymer was 140 °C, 10% weight‐loss temperatures (T_d10) in nitrogen was 458 °C, and char yield at 800 °C in nitrogen higher than 64%. Cyclic voltammogram of the polymer film cast onto an indium‐tin oxide (ITO)‐coated glass substrate exhibited two reversible oxidation redox couples at 0.70 and 1.10 V versus Ag/Ag⁺ in acetonitrile solution. The polymer films revealed excellent stability of electrochromic characteristics, with a color change from yellow green of the neutral form to the dark green and blue of oxidized forms at applied potentials ranging from 0 to 1.3 V. The color switching time and bleaching time were 4.25 and 7.22 s for 860 nm and 5.51 s and 6.48 s for 560 nm. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 1469–1476, 2010