The combination of fluctuation-assisted crystallization and interface-assisted crystallization in a crystalline/crystalline blend of poly(ethylene oxide) and poly(ε-caprolactone)

The nucleation and crystallization of poly(ethylene oxide) (PEO) and poly(ε-caprolactone) (PCL) in the PEO/PCL blends have been investigated by means of optical microscopy (OM) and differential scanning calorimetry (DSC). During the isothermal or nonisothermal crystallization process, when the adjacent PEO is in the molten state, PCL nucleation preferentially occurs at the PEO and PCL interface; after the crystallization of the adjacent PEO, much more PCL nuclei form on the surface of the PEO crystal. However, PEO crystallizes normally and no interfacial nucleation occurs in the blend. The concentration fluctuation caused by liquid–liquid phase separation (LLPS) induces the motion of PEO and PCL chains through interdiffusion and possible orientation of chain segments. The oriented PEO chain segments can assist PCL nucleation, and the heterogeneous nucleation ability of PEO increases with the orientation of PEO chains. Oriented PCL chain segments have no heterogeneous nucleation ability on PEO. It is postulated that the interfacial nucleation of PCL in the PEO/PCL blend follows the combination of “fluctuation-assisted crystallization” and “interface-assisted crystallization” mechanisms.

Enhanced photodegradation of TiO2-containing poly(ε-caprolactone)/poly(lactic acid) blends

The calamitous accumulation of plastic waste in the environment, especially single-use disposables, calls for new approaches to materials design. One method to address the persistence of plastics beyond their intended use is to impart them with functionalities that will either allow for their recyclability or their degradation to basic natural components. This work focuses on the fabrication of photodegradable polyester blends and investigates the impact of compatibilization on photodegradation rates. Specifically, we blended poly(ε-caprolactone) (PCL) and poly(lactic acid) (PLA) polymers by (reactive) extrusion in the presence or absence of dicumyl peroxide (DCP), a radical generator, and titanium dioxide (TiO₂), an inorganic photocatalyst. We examined the effects of DCP and TiO₂ loadings as well as copolymer composition on the thermomechanical properties, photodegradability, and morphology. We found that the inclusion of TiO₂ dramatically increased flexural moduli and photodegradation rates in both dry and wet conditions, while reactive compatibilization had little effect of the tested properties. This simple and scalable approach is promising to fabricate materials that can readily photodegrade.     

Non-isothermal crystallization kinetics and degradation kinetics studies on barium thioglycolate end-capped poly(ε-caprolactone)

Journal of Thermal Analysis and Calorimetry - The poly(ε-caprolactone) (PCL) was synthesized by ring-opening polymerization at 160 °C under nitrogen atmosphere for 2 h...     

Abiotic degradation of poly(dl-lactide), poly(ɛ-caprolactone) and their blends

An effective hydrolytic degradation of PDLLA, PCL and their blends in a phosphate-buffered solution of pH 4.0 at 37 °C for 18 weeks was achieved, observing a considerably faster degradation of PDLLA as compared to PCL due to the hydrophobic and semicrystalline nature of PCL matrix, able to partially prevent water diffusion into the bulk specimen.DSC and FTIR results indicated that PCL phase, in compositions rich in PCL, was very stable against hydrolysis, but the presence of PDLLA in the PDLLA/PCL blends seemed to catalyze the hydrolytic degradation of the PCL phase, probably associated to easier diffusion of water into the PCL domains by the presence of PDLLA amorphous regions. This last trend was proportional to the content of PDLLA in the blends, excepting for the composition 64%PDLLA/36%PCL. It was confirmed that PCL molecules partially delayed hydrolysis of PDLLA molecules, according to FTIR analysis, and the water diffusion prevention level was proportional to the content of PCL in the blends, except for the system 64%PDLLA/36%PCL, which presented a lower extent of degradation than neat PDLLA but higher than the blend 80%PDLLA/20%PCL. This indicated that PCL molecules did not significantly impede hydrolysis of PDLLA molecules in this blend, possibly due to the achievement of a particular structure of the PDLLA/PCL interphase in this blend. In general, hydrolysis of PDLLA/PCL blends was found to be a complex phenomenon depending not only on the content of both polymer phases, but also on the polymer phase crystallinity and morphology.     

Structure-properties correlations in poly(ε-caprolactone)/poly(styrene-co-acrylonitrile)/nanosilica mixtures: Interrelationship among phase behavior,morphology and non-isothermal crystallization kinetics

In this work, the effects of amorphous poly(styrene-co-acrylonitrile) (SAN) chains and hydrophilic and hydrophobic nanosilica at different loadings on the non-isothermal crystallization kinetics of PCL phase have been evaluated using different theoretical models including Avrami, modified Avrami, Ozawa and Mo equations. Using microscopic observations, the interrelations among the changes in the kinetics parameters and the morphology and phase behavior of PCL/SAN and PCL/SAN/nanosilica mixtures have been thoroughly investigated. Microscopic observations on the nanocomposites showed differences in the nanofiller dispersion and distribution state as well as preferential migration and localization state. These differences lead to contradictory trends in the effects of hydrophilic and hydrophobic nanosilica on the crystallization kinetics of pure PCL and PCL/SAN blends. The nanoparticle migration during non-isothermal DSC tests in PCL/SAN blends, the formation of nanoparticle agglomerates at higher loadings, the restrictions imposed on the molecular movements in the crystallization growth stage and slower phase separation and dissolution of PCL/SAN/silica mixtures result in the cooling rate dependence of the kinetics parameters.     

Controlled-release and antibacterial studies of doxycycline-loaded poly(ε-caprolactone) microspheres

The objective of the present study is to achieve doxycycline’s maximum therapeutic efficacy. Doxycycline-loaded poly(ε-caprolactone) microspheres were prepared by water-in-oil-in-water (w/o/w) double emulsion solvent evaporation technique with different formulation variables such as concentrations of drug and polymer. The effects of these variables on surface morphology, particle size distribution, encapsulation efficiency, and in vitro release behavior were examined. To observe the nature of microspheres, X-ray diffraction studies were carried out. The release data obtained were determined using various kinetic models and Korsmeyer–Peppas model showed an acceptable regression value for all compositions. Antibacterial efficiency of doxycycline-loaded poly(ε-caprolactone) microspheres were assessed by determining Minimum Inhibition Concentration (MIC) by standard tube dilution method against four standard pathogenic strains. The in vitro drug release studies were carried out in phosphate buffer solution (pH 7.2). The results showed marked retardation of doxycycline release and higher percentage of polymer gave longer drug release profile. This may definitely provide a useful controlled-release drug therapy and also prove to be effective over a long period of time (76 h).     

Phase separation and phase dissolution in poly(ε-caprolactone)/poly(styrene-co-acrylonitrile) blend

A blend of poly(ε-caprolactone) (PCL) and poly(styrene-co-acrylonitrile) (SAN) containing 27.5 wt% of acrylonitrile having the critical composition (80/20 PCL/SAN) was studied. This PCL/SAN blend having a lower critical solution temperature (LCST) phase boundary at 122 °C offered an excellent opportunity to investigate, firstly the kinetics of phase separation above LCST (125-180 °C), and secondly the kinetics of phase dissolution below LCST (50-115 °C). The blend underwent a temperature-jump above LCST where spinodal decomposition (SD) proceeded, yielding a regularly phase-separated structure (SD structure). Then, it was quenched to the temperatures below LCST when the phase dissolution proceeded. Optical microscopy was used to observe the spinodal decomposition qualitatively while light scattering was used to characterize the phase separation and phase dissolution quantitatively. It was found that during phase dissolution the peak maximum moved towards a smaller angle (wavelength of concentration fluctuations increased) while the peak intensity decreased. This behavior was explained by a model. Also it was found that the fastest phase dissolution kinetics at 80 °C, which was characterized by an apparent diffusion coefficient, was about 10 times slower than the kinetics of phase separation at 180 °C.     

Hydrophobicities of poly(ε-caprolactone) oligomers functionalized with different succinic anhydrides

Different succinic anhydrides were used for modification of hydrophobicities of linear and star-shaped poly (ε-caprolactone) oligomers with different molecular weights. Hydroxyl-terminated poly(ε-caprolactone) oligomers were acid-functionalized either with succinic anhydride (SAH) or with alkenylsuccinic anhydrides (ASAs) containing 8 or 18 carbons in their alkenyl chains. Hydrophobicities of the linear and corresponding star-shaped oligomers were investigated by immersion studies and by water contact angle measurements. In comparison with SAH functionalized oligomers, alkenyl chain containing oligomers showed lower thermal transitions and higher hydrophobicities. In addition, oligomers with 18 carbons alkenyl chain showed considerably higher hydrophobicities than corresponding oligomers with 8 carbon alkenyl chain.     

Impact of the nature and shape of cellulosic nanoparticles on the isothermal crystallization kinetics of poly(ε-caprolactone)

Polycaprolactone (PCL)/cellulose nanocomposites were prepared by mixing PCL with surface modified sisal nanowhiskers (CNW) and microfibrillated cellulose (MFC) extracted from sisal fibers. The influence of cellulosic nanoparticles on the crystallization behavior of PCL was investigated by differential scanning calorimetry. Isothermal crystallization data were modeled with Avrami’s kinetics, Lauritzen–Hoffman secondary nucleation theory and equilibrium melting points were determined with the Hoffman–Weeks method. The cellulose nanoparticles, acting as nucleating agents, drastically accelerate the crystallization of PCL while depressing its equilibrium melting by 9–10 °C. The crystallization of MFC-nanocomposites is slightly faster than that of CNW-nanocomposites, in agreement with the slightly lower bulk activation energy for crystallization and nucleation parameter in the former. The results are discussed based on the differences of specific surface area and surface chemistry of nanoparticles, as well as the confinement phenomenon.     

Synthesis and properties of poly(isosorbide 2,5-furandicarboxylate-co-ε-caprolactone) copolyesters

Bio-based poly(isosorbide 2,5-furandicarboxylate-co-ε-caprolactone) (PIFCL) copolyesters were synthesized from 2,5-furandicarboxylic acid, isosorbide and ε-caprolactone. The obtained copolyesters were characterized by ¹H NMR, ¹³C NMR, intrinsic viscosity, GPC, DSC, TGA and tensile testing. The NMR characterization results confirmed the insertion of lactones units into poly(isosorbide 2,5-furandicarboxylate) (PIF) chains. All PIFCL copolyesters were amorphous with T_{D, 5%} higher than 300 °C. The glass transition temperatures of PIFCLs with FDCA molar ratio from 74% to 45% were within the range of 132.1 °C and 72.4 °C. Tensile testing revealed that introduction of ε-caprolactone into PIF chain imparted PIFCL with excellent mechanical performance, typically, PIFCL polyseter with FDCA molar ratio of 45% had a Young's modulus 858 ± 92 MPa, a tensile strength 44 ± 4 MPa and an elongation at break 480 ± 45%.     

Diselenide-containing poly(ε-caprolactone)-based thermo-responsive hydrogels with oxidation and reduction-triggered degradation

Herein, novel multi-responsive injectable polyester hydrogels were reported based on the diselenide-containing poly(ε-caprolactone) copolymers ((mPEG-PCL-Se)₂). The (mPEG-PCL-Se)₂ solution remained a free-flowing state at ambient temperature but spontaneously turned into a semisolid hydrogel upon heating to physiologic temperature. The phase transition temperature was examined to be dependent on the composition and aqueous concentration of the copolymers. More importantly, the thermo-responsive hydrogels were endowed with oxidation and reduction-triggered degradation by the incorporation of diselenide groups. Accordingly, the degradation of poly(ε-caprolactone)-based hydrogels was greatly improved and the rate of degradation was well regulated by the concentration of hydrogen peroxide (H₂O₂) or glutathione (GSH). This superior stimuli-responsive degradation could lead to an enhanced drug release of encapsulated drug (Doxorubicin, DOX). Thus the oxidation and reduction-triggered degradable diselenide-containing poly(ε-caprolactone) hydrogels would offer great potential for the controlled drug delivery.     

Thermomechanical properties of cured isophtalic polyester resin modified with poly(ε-caprolactone)

The effect of a low profile additive, poly(ε-caprolactone) (PCL), on the thermal and mechanical properties of unsaturated polyester resins (UP) was investigated by differential scanning calorimetry (DSC), dynamic mechanical thermal analysis (DMTA), and tensile tests. The morphology of the systems has been studied by scanning electronic microscopy (SEM). Two PCL molecular mass were selected (PCL2: M _n = 2000 g mol⁻¹ and PCL50: M _n = 50000 g mol⁻¹) to analyze the influence of the molecular mass and the content of PCL on the UP resins and to establish the relation between thermomechanical behavior and morphology. DSC and DMTA glass transition temperatures (T _g) of the UP cured samples containing PCL indicate that PCL2 is miscible with UP whereas for UP + PCL50 system, T _g values are very close to the ones corresponding to neat UP. Besides in UP + PCL2 systems, one phase morphology is observed in which PCL2 would act as solvent of the reacting mixture along curing process; however, UP + PCL50 systems present phase-separated morphology. The presence of PCL2 and PCL50 in UP resin leads to a decrease of the tensile strength and the Young′s modulus as much notorious as the PCL concentration increases. For UP + PCL2 system the elongation at fracture increases in relation to neat UP, increasing as well with the PCL content.     

Enhanced mechanical property of chitosan via blending with functional poly(ε-caprolactone)

Blends of chitosan and poly(ε-caprolactone-co-2-oxepane-1,5-dione) (PCO) were fabricated by solvent casting technique using 77% acetic acid as the cosolvent. The interactions between chitosan and PCO were analyzed by Fourier transform infrared spectroscopy, nuclear magnetic resonance, and differential scanning calorimetry. The miscibility became poorer with increase of PCO from 50% to 75%, which was supported by the Flory–Huggins interaction parameter and crystallinity of PCO. According to X-ray pattern, crystallinity of CS became weaker when PCO content was improved. Results indicated that there existed stronger interactions in comparison with PCL/CS blends. Therefore, the addition of functional polyester PCO made the brittle chitosan ductile. The elongation was significantly prolonged to 21.60 ± 4.92% with the break stress maintaining about 32 MPa, better than that of PCL blends. The degradation behavior showed slower degradation rate compared with pure CS and the morphology was illustrated by scanning electron microscopy. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2013     

Thermal,mechanical, and topographical evaluation of nonstoichiometric α-cyclodextrin/poly(ε-caprolactone) pseudorotaxane nucleated poly(ε-caprolactone) composite films

Three pseudorotaxanes (PpR) comprised of poly (ε-caprolactone) (PCL) and α-cyclodextrin (α-CD) with varying stoichiometric ratios were synthesized and characterized. Wide-angle X-ray diffraction (WAXD) and thermogravimetric (TGA) analyses provided conclusive evidence for complexation between the guest PCL and host α-CD. The as-synthesized and characterized PpRs were used at 10 and 20% concentrations as nucleants to promote the bulk PCL crystallization in composite films. Both WAXD and TGA provided evidence for intact PpR structures in the composite films. Isothermal differential scanning calorimetric (I-DSC) analyses, performed at various crystallization temperatures demonstrated significant differences in the crystallization patterns among the composite films. In addition, I-DSC analyses showed higher Avrami constant values (n) in the PpR-nucleated composite PCL films (n ~ 3), indicating 3-dimensional crystal growth. In the case of neat PCL films, however, lower n values indicated crystal growth in 1-dimensions or 2-dimensions. Moreover, atomic force microscopic analyses showed large crests and pits in PpR-nucleated PCL composites, with irregular morphologies leading to higher surface roughness. To the contrary, the crests and pits were much smaller in the neat PCL films, resulting in lower surface roughness values. Finally, mechanical testing revealed higher tensile strength for PpR-nucleated PCL composites films, demonstrating larger load bearing capabilities. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2018 , 56, 1529–1537     

Anionically prepared poly(ε-caprolactam-co-ε-caprolactone) and poly(ε-caprolactam-co-δ-valerolactone) copolymers: Thermal and mechanical properties

Thermal and representative physico-mechanical properties of newly prepared poly[(ε-caprolactam)-co-(ε-caprolactone)] and poly[(ε-caprolactam)-co-(δ-valerolactone)] copolymers were studied. The copolymers were synthesized by anionic polymerization of ε-caprolactam activated by isocyanate end-capped oligomeric aliphatic polyesters designated as the macroactivators (MAs). Type, concentration and molecular weight of the MAs were varied, which resulted in copolymers with different structure and properties. The impact of the new MAs used in this study on the glass transition temperature and the melting temperature of poly-ε-caprolactam was investigated by DSC. DMTA was used to analyze the effect of copolymerization on the storage modulus (E^′) and tan δ of poly-ε-caprolactam. Conventional and high-resolution TGA data revealed that all the synthesized polyesteramides possess good thermal stability. Mechanical properties were studied by notched impact and tensile testing. According to the experimental data the impact toughness increase with the MA content, being six time higher compared to the poly(ε-caprolactam) in the best situation. Water absorption was also considered in relation to the composition of the copolymers.     

A facile synthesis of hydrophilic poly(ε-caprolactone)-based poly(ether-ester-amide)s

Segmented poly(ether-ester-amide)s, (PEEA)s, of controlled hydrophilicity degree, based on poly(ε-caprolactone) (PCL), were synthesized according to a facile two-step procedure using α,ω-dihydroxy oligomeric PCL, 4,7,10-trioxa-1,13-tridecanediamine and macromers prepared from poly(ethylene glycol)s and adipoyl chloride. The PEEAs showed M _n values in the range 5–11.5 kDa. A PCL-type crystallinity was found by WAXS. DSC indicated T_m values (49–51 °C) close to that of PCL macromer. Single glass transitions were observed both by DSC and DMTA techniques and the T_g values (−58–−50 °C by DSC) were slightly higher than that of PCL. The water uptake was in the range 4.8–26.0 wt.-% depending on the length of the poly(ethylene glycol) segment.

Monomers used to prepare the PEEAs.     

Melting of poly(ε-caprolactone) studied by step-heating calorimetry

This study demonstrates that the step-heating calorimetry, which is a kind of temperature-modulated differential scanning calorimetry, can provide valuable information on the polymer melting. Time-dependent heat flow due to the melting of lamellar crystallites in a narrow range of thickness can be directly observed, from which thickness distribution of lamellar crystallites and thickness dependence of the melting kinetics are deduced. A sample of poly(ε-caprolactone) was used as a model material of semi-crystalline polymer, which has high crystallinity (0.79) so that no recrystallization and/or reorganization occur during melting in the step-heating scan. It was revealed that superheating dependence of the melting rate coefficient increases with increasing lamellar thickness, which may be attributed to variation of the fold surface roughness with respect to lamellar thickness. Analysis based on the cylindrical nucleation model revealed much lower free energy values of lateral surface than that evaluated from crystallization behavior, suggesting that the nucleus for melting is more stable than that for crystallization.     

Physicochemical characterization of self-assembled poly(∈-caprolactone) grafted dextran nanoparticles

Amphiphilic graft copolymer composed of poly(∈-caprolactone) and dextran was synthesized by ring opening polymerization of ∈-caprolactone initiated through the hydroxyl end of dextran in the presence of stannous 2-ethylhexanoate [Sn (oct)₂] as a catalyst. It has been widely characterized by Fourier transform infrared spectroscopy, ¹H NMR, and thermogravimetric analysis. Nanoparticles were prepared in aqueous medium by co-solvent evaporation technique at room temperature (25 °C). Hydrodynamic diameter and particle size were measured by dynamic light scattering spectroscopy and atomic force microscopy, respectively. Core-shell geometry of polymeric nanoparticle was characterized by fluorescence spectrophotometer using pyrene as a probe. Critical micelle concentration of polymer in triple distilled water decreased from 6.9 × 10⁻⁴ to 8.9 × 10⁻⁴ g/l with increasing hydrophobic moiety. Further, the physiological stability of the nanoparticles in phosphate buffer saline of pH 7.4 at 37 °C was evaluated, which showed promising in drug delivery system.