Adsorption behavior of PS‐PEO diblock copolymers on silver and alumina surfaces: A surface plasmon resonance study

In this work, the adsorption behavior at the silver/toluene and alumina/toluene interface of polystyrene–polyethylene oxide (PS‐PEO) diblock copolymers of various molecular weights was investigated by implementation of the surface plasmon resonance (SPR) technique. This was accomplished under a careful choice of experimental setup and the use of a suitable physical model for the interpretation of the experimental data. Comparison between polystyrene homopolymer and PS‐PEO diblock copolymer adsorption measurements indicate that PS‐PEO is anchored on the alumina surface via the PEO block, while on silver the copolymer is attached by various chain segments. The measured final adsorption amounts on alumina are typical of end‐attached polymeric brush formation while the dynamics of the adsorption process present two clearly different evolution regimes. This work provides insight into the many advantages of the use of the SPR technique as a valuable tool for similar surface studies. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1580–1591, 2006     

Phase separation in thin films of end‐grafted block copolymers

An atomic force microscopy investigation was carried out on various thick (30–120 nm) polymethyl methacrylate‐b‐polystyrene and poly(2‐(dimethyl amino)ethyl methacrylate)‐b‐polystyrene films prepared via a grafting‐from method. The structure of the films was examined with both topographic and phase imaging. Several different morphologies were observed including a perforated lamellar phase with irregular perforations. In addition, complementary small‐angle X‐ray scattering and reflectometry results measurements on a non‐grafted polymer are presented. Copyright © 2009 John Wiley & Sons, Ltd.     

Selective swelling blends of block copolymers for nanoporous membranes with enhanced permeability and robustness

Block copolymers (BCPs) are important precursors to produce membranes with well‐defined porosities. However, it remains challenging to prepare robust and affordable BCP‐based membranes. In this work, cheap commodity styrene‐butadiene‐styrene (SBS) elastic triblock copolymers are mixed with polystyrene‐block‐poly (2‐vinylpyridine) (SV) block copolymers in solutions, leading to macroscopically stable blend films upon casting because of the compatibilizer effect of PS existing in both copolymers. By soaking the blend films in ethanol, the microdomains of poly(2‐vinylpyridine) are selectively swollen and cavitated upon drying, resulting in a hierarchical structure with perforated SV phases interwoven with the SBS phases. The blend membranes with 30% SBS exhibit improved water permeability and mechanical robustness due to the presence of elastic SBS compared to neat SV membranes; meanwhile, the rejections of the blend membranes remain largely unchanged. Moreover, the blend membranes exhibit a pH‐responsive function, and homoporous SV regions are obtained by pre‐aligning the SV phases. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55, 1617–1625     

Synthesis,self‐assembly and adsorption of PEO–PLA block copolymers onto colloidal polystyrene

A series of amphiphilic block copolymers composed of poly(ethylene oxide) and poly(lactide) were synthesized and their solution properties studied using static and dynamic light scattering. These materials self‐assemble in aqueous media with the hydrodynamic radius increasing with increasing hydrophobic fraction in the copolymer. To ascertain the potential for use of these materials as degradable coatings in delivery applications, block copolymers of varying compositions were adsorbed onto a series of colloidal polystyrene particles with varying radii, and the thickness of the adsorbed layer was determined from changes in the hydrodynamic size. The adlayer thicknesses ranged from 3 to 14 nm with varying block copolymer compositions, and colloid radii. The trends fit well with theoretical models for adlayer thickness, with the exception of the smallest colloids. In these systems, we propose that the colloids may become encapsulated into the block copolymer assembly. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 244–252, 2008     

Maleimidophenyl isocyanates as postpolymerization modification agents and their applications in the synthesis of block copolymers

The maleimide structure is highly reactive, exemplified by thiol–ene click reactions with thiols and Diels–Alder reactions with furans. Although postpolymerization modifications and macromolecular conjugations involving maleimide units have been widely studied, mostly due to their selectivity and high reactivity, little has been reported on the one‐pot postpolymerization introduction of maleimides in polymer chains. Herein, we report p‐maleimidophenyl isocyanate and its derivatives as modification agents to introduce maleimide moieties by reaction with hydroxy groups into polymer chains. The high reactivity of the resulting modification agents and of the corresponding maleimide structures once inserted in the polymer chains was examined by studying their reaction kinetics. Furthermore, these modification agents were successfully applied to the synthesis of macromonomers for graft polymerization and various block copolymers, with, for example, AB‐type, star‐shaped, and H‐shaped architectures. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019 , 57, 2396–2406     

Transmission electron microscopy of saturated hydrocarbon block copolymers

Contrast for transmission electron microscopy (TEM) of microphase-separated saturated hydrocarbon diblock copolymers has been obtained using ruthenium tetroxide (RuO₄). This technique exploits differences in the rate of transport of the oxidizing stain in rubbery amorphous versus semicrystalline, or glassy, microdomains. Rapid quenching from above the melting (T_m), or glass transition (T_g) temperature is shown to preserve the equilibrium melt morphology in poly(ethylene)-poly(ethyl-ethylene) (PE-PEE), poly(ethylene)-poly(ethylene-propylene) (PE-PEP), and poly(vinylcyclohexane)-poly(ethyl-ethylene) (PVCH-PEE) diblock copolymers; PE melts at 108°C, PVCH is glassy up to about 140°C, while PEE and PEP remain rubbery down to approximately-20°C and ?56°C, respectively. Treatment of ultrathin sections of the quenched specimens with RuO₄ vapor led to welldefined TEM images, that revealed microdomain type and order. These results are consistent with SANS data taken under equilibrium conditions. © 1995 John Wiley & Sons, Inc.     

New methodology for synthesizing polyolefinic graft block copolymers and their morphological features

This paper describes a new synthetic route for polyolefinic graft block copolymers by adopting coupling reaction between terminally hydroxylated polyolefins and maleic anhydride grafted polyolefins. Terminally hydroxylated polypropylene (PP-OH) was coupled with maleic anhydride modified polyethylene (PE-g-MAH) and such ethylene-propylene random copolymer (EPR-g-MAH) to give polyolefinic graft block copolymers (PE-g-PP and EPR-g-PP, respectively). The formation of PE-g-PP was confirmed by enhancement on molecular weight and it brought about distinctive decrease in size of dispersed domain in its phase separation morphology. Occurrence of coupling reaction to give EPR-g-PP was indicated by extreme decrease in its solubility to n-decane and it led to unique morphology demonstrating lamella microstructure that had never been reported for a comparable polyolefin composite.     

Graft and block copolymers with polysiloxane and vinyl polymer segments

A convenient new process to make silicone/organic block and graft copolymers has been recently demonstrated. This dual copolymerization process combines conventional condensation polymerization of the siloxane segments with free radical polymerization of the organic vinyl polymer segments. The copolymerization process is relatively simple and economical compared with other copolymerization techniques as it uses commonly available starting materials and available process equipment. Silicone segments containing alkene side chains or end-groups are prepared in the usual way by polycondensation using an acid or base catalyst. The double bonds of the alkene groups are oxidized to carbonyls which are then used to initiate vinyl monomer polymerization and link the siloxane with the vinyl segments. This initiation step is based on a redox system of copper^(II) salts which generates free radicals on the alpha carbons next to the carbonyl groups. This copolymerization process is relatively fast and proceeds at high yields.     

Ozonolysis efficiency of PS‐b‐PI block copolymers for forming nanoporous polystyrene

A PS‐b‐PI diblock copolymer has been synthesized and blended with a homopolystyrene of a variable molecular weight at a variable weight ratio, resulting in different volume fractions of PS to PI and various morphologies. After being cast as a film, the double bonds in the PI microdomains were cleaved via ozonolysis resulting in the formation of a nanoporous PS. The ease of ozonolysis depended strongly upon the morphology of the PI microdomains. The degree of ozonization after 24‐h reaction was about 90% for lamellar microdomains, about 80% for bicontinuous microdomains, about 70% for cylindrical microdomains, and about 50% for spherical microdomains. These variations were attributed to the decrease in the contact area of PI microdomains with ozone and the total volume of PI microdomains accessible to ozone. All PS‐b‐PI/homopolystyrene samples have turned into nanoporous materials after the removal of PI nanodomains. SEM, AFM, and TEM images indicated that the resulting PS had a pore size of 20–30 nm, and thus was potentially useful for photonic crystals or fuel cell applications. © 2008 Wiley Periodicals, Inc. JPolym Sci Part A: Polym Chem 46: 1964–1973, 2008     

Compatabilization of polystyrene/polypropylene blends by styrene–butadiene block copolymers with differing polystyrene block lengths

Compatibilization of polystyrene/polypropylene (PS/PP) blends, by use of a series of butadiene–styrene block copolymers was studied by means of small‐angle X‐ray scattering (SAXS) and transmission electron microscopy (TEM). The compatibilizers used differ in molar mass and the number of blocks. It was shown that the ability of a block copolymer (BC) to participate in the formation of an interfacial layer (and hence in compatibilization) is closely associated with the molar mass of styrene blocks. If the styrene blocks are long enough to form entanglements with the styrene homopolymer in the melt, then the BC is trapped inside this phase of the PS/PP blends, and its migration to the PS/PP interface is difficult. In this case, the BC does not participate in the formation of the interfacial layer nor, consequently, in the compatibilization process. On the other hand, the BC's with the molar mass of the PS blocks below the critical value are proved to be localized at the PS/PP interface. This preferable entrapping of some styrene–butadiene BC's in the PS phase of the PS/PP blend is, of course, connected to the differing miscibility of the BC blocks with corresponding components of this blend. Although the styrene block is chemically identical to the styrene homopolymer in the blend, the butadiene block is similar to the PP phase. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 1647–1656, 1999     

Selective hydrolysis of oxazoline block copolymers

Block copolymers, composed of a hydrophobic block [poly(N-t-butylbenzoyl ethylenimine) or poly(N-lauroyl ethylenimine)] and a hydrophilic block [poly(N-propionyl ethylenimine)], synthesized by cationic ring-opening polymerization of 2-substituted Δ2-oxazolines, were selectively deacylated by acid hydrolysis. The hydrolysis process was monitored by using ¹H-NMR. The results show that the propionyl groups could be removed from the hydrophilic block of the polymer chain without touching the hydrophobic block, if appropriate reaction conditions were used.     

Hybrid metal–polymer composites from functional block copolymers

The combination of metals and polymers in hybrid materials is a research area of great current interest. A number of methods for controlling the positioning of metallic species within polymer matrices on the nanometer scale have been developed. This highlight focuses on the use of functional block copolymers for the localization of metal species, especially nanoparticles, on the nanometer scale through block copolymer phase segregation. Research from the author's group on the use of alkyne‐functional block copolymers for the preparation of cobalt‐containing materials is discussed in this context. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 4323–4336, 2005     

The influence of confinement and curvature on the morphology of block copolymers

In the bulk, at equilibrium, diblock copolymers microphase separated into nanoscopic morphologies ranging from body-centered cubic arrays of spheres to hexagonally packed cylinders to alternating lamellae, depending on the volume fraction of the components. However, when the block copolymers are forced into cylindrical pores, where the diameter of the pores are only several repeat periods of the copolymer morphology or less, then commensurability of the copolymer period and the pore diameter can impose a frustration on the microdomain morphology. In addition, due to the small pore diameter, a curvature is forced on the microdomain morphology. In combination with interfacial interactions between the blocks of the copolymer and the pore walls, the preferential segregation of one component to the walls, spatial confinement and forced curvature are shown to induce transitions in the fundamental morphology of the copolymers seen in the bulk. Lamellar morphologies transformed into torus-type morphologies, cylinders are forced into helices, and body-centered cubic arrays of spheres are force into helical arrays of spheres due to these restraints. The novel morphologies, not accesssible in the bulk, open a large array of nanoscopic structures that can be used as templates and scaffolds for the fabrication of inorganic nanostructured materials. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 3377–3383, 2005     

Doubly photoresponsive and water‐soluble block copolymers: Synthesis and thermosensitivity

We report the synthesis and investigation of a new type of photoresponsive block copolymers (BCPs). They were designed to comprise two water‐soluble polymers containing two different photoisomerizable moieties (either azobenzene and spiropyran or two different azobenzenes), with the two constituting blocks that, when separated, exhibit a lower critical solution temperature (LCST) in water and can shift their LCST in opposite directions upon photoisomerization (decrease of LCST for one polymer and increase for the other). A variety of such doubly photoresponsive BCPs were synthesized using either azobenzene‐ or spiropyran‐containing poly(N,N‐dimethylacrylamide) (PDMA), poly(N‐isopropylacrylamide) (PNIPAM) and poly[methoxydi(ethylene glycol) methacrylate] (PDEGMMA). Their thermal phase transition behaviors in aqueous solution before and after simultaneous photoreactions on the two blocks were investigated in comparison with their constituting blocks, by means of solution transmittance (turbidity) and variable‐temperature ¹H NMR measurements. The results show that BCPs displayed a single LCST whose shift upon two photoisomerizations appeared to be determined by the competing and opposing photoinduced effects on the two blocks. Moreover, optically controlling the relative photoisomerization degrees of trans azobenzene‐to‐cis azobenzene and spiropyran‐to‐merocyanine could be used to tune the LCST of BCP solution. This study demonstrates the potential of exploring a more complex photoreaction scheme to optically control the solution properties of water‐soluble thermosensitive BCPs. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 4055–4066, 2010     

Ultradense Polymer Brushes by Adsorption

Standing room only : Dense polymer brushes can be prepared by adsorbing a diblock copolymer comprising a neutral block and a polyelectrolyte block to an oppositely charged polyelectrolyte brush (see picture). The density of the resulting neutral brush is determined by charge compensation, leading to brush densities well over 1 nm^?2. The diblock copolymer can be desorbed by changing the solution conditions.

     

Functionalized block copolymers for preparation of reactive self‐assembled surface patterns

Two phase separating block copolymers equipped with functional groups (acid and alkyne) were synthesized via reversible addition‐fragmentation chain transfer (RAFT) polymerization. Thin films of these materials were prepared and examined with regard to surface morphology, surface composition, and film stability. Self‐assembled structures with domain sizes of about 40 nm were detected through atomik force microscopy (AFM) analysis while X‐ray photoelectron spectroscopy measurements revealed a balanced surface exposure of the two segregated phases. Thus, reactive groups being present in both phases are specifically provided within nanoscopic surface areas. The films showed good stability on exposure to various solvents but the self‐organized surface patterns were only resistant toward ethanol. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011