Preparation and characterization of ultrafine co and ni particles in a polymer matrix

A facile route for in situ synthesis of Co and Ni nanoparticles in a preorganized polyacrylamide gel is reported. Metal-polymer composites were prepared by gamma-irradiation at room temperature. The Co nanoparticles were roughly 3-5 nm in size and were stable in the polymer matrix in the presence of air. The presence of Co and Ni nanoparticles was established by their ability to transfer an electron to methyl viologen {paraquat: 1,1'-dimethyl 4,4'-dipyridinium dichloride; MV(2+) (Cl(-))(2)}. The Co and Ni nanoparticles were probed for their magnetic characteristics by a superconducting quantum interferometer device (SQUID) magnetometer and display a low superparamagnetic blocking temperature T(B) of about 13 and 10 K, respectively. The field-dependent magnetic behavior below T(B) displays the standard features corresponding to superparamagnetism, as expected for very small Co and Ni crystallites. This also suggests that particles are polycrystalline in nature.     

Characterization of magnetic nanoparticles using energy-selected transmission electron microscopy.

Fe, Co, and Ni magnetic nanoparticles have been characterized using energy-selected imaging in a high-resolution transmission electron microscope. The samples comprised Fe/FeO x and Co/CoO x nanoparticles synthesized by inert gas evaporation and a Ni/C nano-composite prepared by a sonochemical method. All of the particles examined were found to be between 5 and 30 nm in size, with the Fe and Co crystals coated in 5-10 nm of metal oxide layer and the Ni metallic crystallites embedded in an amorphous carbon spherical matrix.     

Ultrasound technique as a tool for high-rate incorporation of Al<Subscript>2</Subscript>O<Subscript>3</Subscript> in NiCo layers

NiCo–Al₂O₃ composite coatings were prepared by electrodeposition in a sulfamate plating bath containing Al₂O₃ particles to be co-deposited under sonication. For reliable determination of the microstructure, detailed studies on composite cross-sections were carried out by energy-dispersive spectrometer (matrix composition, particle content) and FE-SEM/electron backscattered diffraction data (particle distribution, grain size), accompanied by XRD analyses concerning texture, lattice parameter, grain size, and residual stress. The NiCo matrix with a Co/Co + Ni ratio up to 0.4 is a face-centered cubic solid solution with <100> and <110> fiber textures. The distribution of the particles (size 250 nm) was well-dispersed and enhanced up to 15 wt.% by ultrasound application during plating. Vickers hardness increased up to 50% by dispersion hardening. First-order residual stress in the matrix increased with rising Co content, thus decreasing wear resistance and revealing the complex of composite properties with partially opposite effects.     

Preparation of chitosan nanoparticles using methacrylic acid

In this work the preparation of chitosan nanoparticle was investigated using methacrylic acid in different conditions and studied by particle size analyzer, zeta-potential, Fourier transform infrared spectroscopy (FT-IR), nuclear magnetic resonance (NMR) and transmission electron microscopy (TEM). The particle size was dependent on the chitosan concentration used during the preparation method. Nanoparticles with sizes as small as 60 nm were achieved, that can be extremely important for several applications. The nanoparticles solution was also pH-sensitive, due to swelling and aggregation of the nanoparticles. The nanoparticles obtained presented a very homogeneous morphology showing a quite uniform particles size distribution and a rather spherical shape.     

Versatile carbon supported mono and bimetallic nanocomposites: synthesis,characterization and their potential application for furfural reduction

Biomass conversion has been developed by testing various metal based carbon catalysts. Most of the reported catalysts either use very expensive metals or support that provides lower selectivity. In this context, we fabricated new carbon based nanocomposites and studied their catalytic application for furfural reduction – a promising biomass derived molecule. The mono (Cu, Co and Ni) and bimetallic (CuCo and CuNi) nanoparticle supported on commercial graphite (CG) were prepared and characterized by TEM, EDS, XRD and Raman spectroscopy. The analysis revealed that the nanocomposites are made up of metallic nanoparticles with average particle size of 5–13 nm on the graphite matrix. The obtained results indicated that the Cu+Ni@CG catalyst exhibited high catalytic activity for furfural reduction, thus leaving Cu+Ni as the finest and cost effective catalyst for this study.     

Biopolymeric delivery system for controlled release of polyphenolic antioxidants

A chitosan based delivery system has been developed for the controlled release of polyphenolic antioxidants such as catechin. Placebo and catechin entrapped particulate delivery systems were prepared using the sodium tripolyphosphate ionic crosslinking technique. The particles have been characterised by transmission electron microscopy, particle size and charge distribution analysis, Fourier Transform infrared spectroscopy, differential scanning calorimetry and entrapment efficiency studies. These studies gave an understanding of the physico-chemical interactions that influence the biopolymer during particle formation and entrapment of catechin. The in vitro release of catechin was carried out in enzyme-free simulated gastric and intestinal fluids. Although nanoparticles could be formed by the crosslinking technique used, there was aggregation behaviour observed after retrieval and freeze-drying of the particles as shown by transmission electron microscopy. Both the placebo and catechin-loaded particles had mean particle size range of about 4.27-6.29 μm after freeze-drying and were charged. Fourier Transform infrared spectroscopy, differential scanning calorimetry studies indicated minor structural interactions between catechin and chitosan matrix. Entrapment efficiency of the particles ranged between 27% and 40%. In vitro release studies indicated that the release of catechin in simulated gastric and intestinal fluids was between 15% and 40%, depending on the structural interactions between catechin and the chitosan matrix.     

Physical and chemical characterization insulin-loaded chitosan-TPP nanoparticles

The purpose of this study was to develop and characterize insulin nanoparticles systems using chitosan. Insulin-loaded nanoparticles were prepared by ionic gelation of chitosan with tripolyphosphate anions (TPP). The interactions between insulin and chitosan were evaluated by differential scanning calorimetry (DSC), thermogravimetry/derivative thermogravimetry (TG/DTG), and Fourier-transform infrared (FTIR) spectroscopy. Besides, particle size distribution, polydispersity index (PDI), zeta potential, and association efficiency (AE%) of the nanoparticles were evaluated. In general, inert nanoparticles and insulin-loaded nanoparticles showed an average size of 260.56 nm (PDI 0.502) and 312.80 nm (PDI 0.481), respectively. Both nanoparticles showed positive charge, but after insulin incorporation the zeta potential was reduced, evidencing its incorporation. Nanoparticles obtained also showed AE% around 70%, measured by high-performance liquid chromatography (HPLC). The results of FTIR, DSC, and TG/DTG corroborated the data presented suggesting that insulin was successfully encapsulated. However, drug incorporation seems to be related not only to electrostatic interactions, but also to physical process and/or adsorption phenomena.     

Electrodeposition of nano-sized nuclei of magnetic Co–Ni alloys onto n-Si (1 0 0)

Nanometer-sized nuclei of Co–Ni alloys were electrodeposited onto n-Si (1 0 0) electrodes from buffered solutions of the metallic ions. The energy levels of the interface Si/(Co(II),Ni(II))_aq were determined from Mott–Schottky plots. Electrodeposition of the alloys occurs by an anomalous mechanism and preferential deposition of Co took place at all the Co(II)/Ni(II) ratios investigated. The morphology and magnetic properties of the nuclei were studied by AFM and MFM, respectively. It is showed that nuclei of height <30 nm and low aspect ratio present a single-domain magnetic behaviour. Larger nuclei depict complex magnetic characteristics, with a progressive built-up of multi-domains.     

Influence of dose on particle size of colloidal silver nanoparticles synthesized by gamma radiation

Colloidal silver nanoparticles were synthesized by γ-irradiation-induced reduction method of an aqueous solution containing silver nitrate as a precursor in various concentrations between 7.40×10^?4 and 1.84×10^?3 M, polyvinyl pyrrolidone for capping colloidal nanoparticles, isopropanol as radical scavenger of hydroxyl radicals and deionised water as a solvent. The irradiations were carried out in a ⁶⁰Co γ source chamber at doses up to 70 kGy. The optical absorption spectra were measured using UV–vis spectrophotometer and used to study the particle distribution and electronic structure of silver nanoparticles. As the radiation dose increases from 10 to 70 kGy, the absorption intensity increases with increasing dose. The absorption peak λ_max blue shifted from 410 to 403 nm correspond to the increase of absorption conduction electron energy from 3.02 to 3.08 eV, indicating the particle size decreases with increasing dose. The particle size was determined by photon cross correlation spectroscopy and the results showed that the particle diameter decreases exponentially with the increase of dose. The transmission electron microscopy images were taken at doses of 20 and 60 kGy and the results confirmed that as the dose increases the diameter of colloidal silver nanoparticle decreases and the particle distribution increases.     

Modification in structural,optical, morphological,and electrical properties of zinc oxide (ZnO) nanoparticles (NPs) by metal (Ni,Co) dopants for electronic device applications

In the present work, Zinc Oxide (ZnO) nanoparticles (NPs) were synthesized by the chemical co-precipitation method using Zinc Chloride as the initial chemical, while Nickel and Cobalt chloride as dopants. Phase identification of metal (Ni, Co) doped Zinc Oxide nanoparticles (NPs) was observed using x-ray diffraction (XRD). The small lattice distortion or phase changes appeared due to shifting of diffraction angles peaks towards larger angle in ZnO are corresponded to metal (Ni, Co) dopant. The average crystallite size appears to decrement in NP size from 7.67 nm to 6.52 nm and 5.35 nm to 5.17 nm with increasing 5 % to 80 % of metal (Ni, Co) dopant respectively. The optical characteristics, including the absorption spectra of the prepared sample were observed through UV–Vis spectroscopy, Meanwhile SEM confirmed the observation of composition change in specimen with metal (Ni, Co) dopant concentration. The bandgap value was also found decrement 5.23 eV to 5.05 eV with increment of metal (Ni, Co) dopant concentration. The functional groups were measured by Fourier transformation infrared spectroscopy (FTIR). FTIR peaks found the metal (Ni, Co) doped ZnO with the vibration mode of (Zn²⁺ –O^2?) ions due to the increment of dopant concentrations. Furthermore, electrical results show the ohmic behavior of prepared samples. These findings indicate the possibility of tuning optical, structural and electrical properties of metal (Ni, Co) doped ZnO with various dopant concentrations of Nickel and will have great potential to find application in optoelectronic devices.     

Characterisation of nickel–zinc ferrite/silica nanocomposites with low ferrite concentration obtained by an improved modified sol–gel method

The paper presents a study regarding the structure, morphology and magnetic behaviour of x% (Ni_0.65Zn_0.35Fe₂O₄)/(100 − x)% SiO₂ ferrimagnetic nanocomposites for low Ni–Zn ferrite concentration (x = 5, 10, 15, 20 and 30 mass percent) obtained by an improved modified sol–gel method. The obtained gels and nanocomposites have been characterized by fast Fourier transform-infrared (FT-IR) spectrometry, X-ray diffraction (XRD), transmission electron microscopy (TEM) and magnetic measurements (MM). The addition of a supplementary quantity of diol in the synthesis, corresponding to a molar ratio EG : TEOS = 1:1, and the control of the thermal treatment applied to the precursor xerogels tetraethylortosilicate (TEOS)–metal nitrates (MN)–ethylene glycol (EG) leads to fine (~2–9 nm), almost spherical Ni–Zn ferrite nanoparticles homogenously dispersed inside the amorphous SiO₂ matrix. TEM images reveal the fine nature and the narrow size distribution of the ferrite nanoparticles. Nanoparticles diameter increases with the ferrite concentration and with the annealing temperature. For all concentrations of ferrite in SiO₂ and all annealing temperature, we have obtained Ni_0.65Zn_0.35Fe₂O₄ ferrite as single phase (proven by XRD) in the amorphous silica matrix, only after a pre-treatment of synthesized gels, at 573 K, for 3 h. The magnetic behaviour of ferrite nanoparticles in quasi-static magnetic fields is very particular, depending on the annealing temperature and the ferrite content in silica matrix. We have obtained superparamagnetic behaviour for the nanocomposites, for a concentration of 30% ferrite in SiO₂ at high annealing temperature, of 1,273 K.     

Nanoparticles prepared by self-assembly of Chitosan and poly-γ-glutamic acid

The present paper describes the preparation and characterization of novel biodegradable nanoparticles based on self-assembly of poly-gamma-glutamic acid (γ-PGA) and chitosan (CH). The nanosystems were stable in aqueous media at low pH conditions. Solubility of the systems was determined by turbidity measurements. Surface charge and mobility were measured electrophoretically. The particle size and the size distribution of the polyelectrolyte complexes were identified by dynamic light scattering and transmission electron microscopy (TEM). It was found that the size and size distribution of the nanosystems depends on the concentrations of γ-PGA and CH solutions and their ratio as well as on the pH of the mixture and the order of addition. The diameter of individual particles was in the range of 20–285 nm measured by TEM, and the average hydrodynamic diameters were between 150 and 330 nm. These biodegradable, self-assembling stable nanocomplexes might be useful for several biomedical applications.     

Synthesis of Ni nanoparticles and their characterizations

Ni nanoparticles were synthesized by solution reduction process successfully. The influence of parameters on the size of Ni nanoparticles was studied and the referential process parameters were obtained. The morphology and structure of the synthesized Ni nanoparticles were characterized by transmission electron microscopy (TEM), powder X-ray diffraction (XRD), QELS data and infrared spectroscopy (IR). The result shows that Ni nanoparticles are of high purity and the average size of Ni nanoparticles was found to be 13 ± 2 nm.     

Chitosan‐induced synthesis of magnetite nanoparticles via iron ions assembly

Superparamagnetic magnetite nanoparticles were synthesized induced by chitosan hydrogel under ambient conditions via iron ions assembly, and the inducing effect of chitosan hydrogel was discussed. Results of X‐ray diffraction and transmission electron microscopy indicate that the nanoparticles were inverse cubic spinel structure magnetite with diameter about 16 nm, and the superparamagnetic nanoparticles with narrow size distribution dispersed uniformly in chitosan. The magnetization measurements indicated that the nanoparticles showed the typical superparamagnetic behavior. The crystallinity, morphology, and magnetic properties of magnetite nanoparticles were remarkably influenced by the pH values of iron ion solutions. The interaction between magnetite and chitosan was illustrated by FT‐IR and thermogravimetric analysis, which concluded that the magnetite nanoparticles were coated by a chitosan layer via the amino groups of chitosan. The chitosan hydrogel assisted in the synthesis of superparamagnetic magnetite nanoparticles through chelation by amino groups. Copyright © 2008 John Wiley & Sons, Ltd.     

Design and synthesis of novel magnetic core-shell polymeric particles

A novel synthetic strategy was developed for the preparation of magnetic core-shell (MCS) particles consisting of hydrophobic poly(methyl methacrylate) cores with hydrophilic chitosan shells and gamma-Fe2O3 nanoparticles inside the cores via copolymerization of methyl methacrylate from chitosan in the presence of vinyl-coated gamma-Fe2O3 nanoparticles. The magnetic core-shell particles were characterized with transmission electron microscopy, field-emission scanning electron microscopy, particle size and zeta-potential measurements, vibrating sample magnetometry, and atomic force microscopy, respectively. The MCS particles were less than 200 nm in diameter with a narrow size distribution (polydispersity = 1.09) and had a good colloidal stability (critical coagulation concentration = 1.2 M NaCl at pH 6.0). Magnetization study of the particles indicated that they exhibited superparamagnetism at room temperature and had a saturation magnetization of 2.7 A m2/kg. The MCS particles were able to form a continuous film on a glass substrate, where magnetic nanoparticles could evenly disperse throughout the film. Thus, these new materials should be extremely useful in various applications.     

Hybrid materials based on polymethylsilsesquioxanes containing Fe,Pt, and Fe–Pt metallic nanoparticles

New hybrid materials based on Pt, Fe, and Pt–Fe nanoparticles stabilized in a matrix of polymethylsilsesquioxane nanogel and ultrahigh molecular weight polyethylene (UHMWPE) were prepared. Metal vapor synthesis was used to produce mono- and bimetallic nanoparticles. It was shown that organosilicon nanogel effectively stabilizes Pt nanoparticles with an average size of 0.9 nm. Using the nanogel results in the formation of superparamagnetic Fe particles 3–5 nm in size that consist of ferromagnetic Fe⁰ core and antiferromagnetic shells of Fe oxides. It is established that using an organosilicon matrix in the formation of Pt-Fe/UHMWPE systems helps reduce the average particle size of Fe in the material from 6.5 to 4.5 nm and narrow their particle size distribution. The composition, magnetic and electronic characteristics of the nanocomposites are studied via transmission electron microscopy, X-ray photoelectron spectroscopy, Mössbauer spectroscopy, XANES, and EXAFS.     

Formulation of Nanoencapsulated Catechin with Chitosan as Encapsulation Material

Gambier is one of Indonesian superior estate crop. Among several chemical compounds in gambier, catechin from polyphenols group has the greatest benefit for health. However, catechin has a limitedness of stability that causes a low bioavailability property. One way to maintain and improve the stability of catechin is the application of nanotechnology. The objective of this study is to obtain the best formulation in producing a solution of catechin nanoparticles with particle droplet size <300 nm as an antioxidant material. Observations were conducted to the formulations of the concentration of the solution of chitosan (0.2 and 0.4%), sodium tripolyphosphate (Na-TPP) (0.1 and 0.2%), catechin extract (0.3, 0.4, 0.5 and 0.6%) and the ratio of chitosan solution with catechin solution in Na-TPP (5: 1 and 7: 1) in order to determine one that yields the best solution. Observations were carried on the stability and characteristics of catechin nanoparticle solution including particle size, particle surface topography and internal structure. Catechin nanoparticles with best particle size was found in formula with 0.2% chitosan solution, 0.4% catechin solution, 0.1% Na-TPP solution and ratio of chitosan solution with withcatechin in Na-TPP solution 7: 1, that is 137.6 nm. Physically, the best formulation of catechin nanoparticleshas good particle surface topography, internal particle structure and emulsion stability.     

A simple method to ordered mesoporous carbons containing nickel nanoparticles

A series of ordered mesoporous carbons containing magnetic Ni nanoparticles (Ni-OMCs) with a variety of Ni loadings was made by a simple one-pot synthetic procedure through carbonization of phenolic resin-Pluronic block copolymer composites containing various amount of nickel nitrate. Such composite materials were characterized by N₂ sorption, XRD, and STEM. Ni-OMCs exhibited high BET surface area, uniform pore size, and large pore volume without obvious pore blockage with a Ni loading as high as 15 wt%. Ni nanoparticles were crystalline with a face-center-cubic phase and observed mainly in the carbon matrix and on the outer surface as well. The average particle size of Ni nanoparticles was dependent on the preparation (carbonization) temperature and Ni loading; the higher the temperature was used and the more the Ni was incorporated, the larger the Ni nanoparticles were observed. One of the applications of Ni-OMCs was demonstrated as magnetically separable adsorbents. Dedicated to Professor Mietek Jaroniec on the occasion of his 60th birthday.     

Influences of surfactant (PVA) concentration and pH on the preparation of copper nanoparticles by electron beam irradiation

Electron beam irradiation method was successfully applied to the preparation of Cu nanoparticles in aqueous solution under room temperature and ambient pressure using polyvinyl alcohol (PVA) as the surfactant. The influences of the pH on the products were studied by X-ray diffraction (XRD), and those of the surfactant PVA concentration on the particle size and agglomeration by ultraviolet–visible spectrophotometry (UV–vis) and laser scattering particle size distribution analysis (LSPSDA). The products were characterized by XRD and transmission electron microscopy (TEM). The results showed that the grain size of Cu nanoparticles, within a certain range, can decrease with increasing PVA concentration. Pure Cu nanoparticles with the grain size distribution of 5–50 nm were prepared when the pH was adjusted between 5.0 and 9.0, and the PVA concentration was 2.20 g/100 mL.     

Formation of positively charged poly(butyl cyanoacrylate) nanoparticles stabilized with chitosan

To investigate the formation of positively charged nanoparticles (NP) stabilized with chitosan, positively charged poly(butyl cyanoacrylate) (PBCA) NP were prepared by emulsion polymerization in the presence of chitosan as a polymeric stabilizer at low pH. The effect of physicochemical factors such as the pH, the concentration and the volume of the chitosan solution, the chitosan molecular weight and the temperature on the mean particle size and the turbidity of PBCA-NP was investigated. Particle size was determined using a transmission electron microscope. The chemical interaction between chitosan and PBCA was identified by Fourier transform infrared (FT-IR) spectroscopy and the grafting percentage at various pH values was determined. The zeta potential of PBCA-NP coated with chitosan was determined from the electrophoretic mobility in 10 mM NaCl. The pH, the concentration and the volume of the chitosan solution and the molecular weight of chitosan were shown to be important factors in controlling the mean particle size of NP in the range 10–100 nm. FT-IR spectra indicated that chitosan was covalently linked to PBCA and the maximum grafting percentage reached about 120% w/w at pH 2.0. Nimodipine as a model drug was successfully incorporated into chitosan-stabilized PBCA-NP with a mean particle diameter of 31.6 nm. PBCA-NP coated with chitosan carried a positive charge. The results indicate that positively charged NP may be produced in the presence of cationic polysaccharide chitosan and might increase their potential use as a targeting drug delivery system. Received: 17 March 1999/Accepted in revised form: 4 October 1999