Gain evaluation of compact designing on Er/Yb codoped germanate glass channel waveguide

Bent waveguide structures (U- and F-bend) based on UV-sensitive Er³⁺/Yb³⁺ codoped germanate glass substrates have been designed to achieve high-gain C-band amplification. Using simulated-bend method, the optimal radius for curved structure is offered to be 1.90 cm with loss coefficient of 0.0015 dB/cm, as the substrate size is minimally schemed. In the wavelength range of 1528–1559 nm, obvious gain enhancement for the bent structure waveguides is anticipated, while, for the F-bend waveguide, the internal gain at 1533.8 nm wavelength is derived to be 22.55 dB, which is much higher than the value of 14.06 dB in the U-bend waveguide, and over three times higher than that of the straight one, after compensating both the bend loss and the transition loss. The simulation results indicate that the bent structure designing is beneficial in attaining high optical gain in Er³⁺/Yb³⁺ codoped germanate glass substrates, which assures that long-period grating can be applied to implement practical C-band gain-flattened amplification.     

Er-Yb co-doped glass waveguide amplifiers using ion exchange and field-assisted annealing

Er³⁺-Yb³⁺ co-doped waveguide amplifiers fabricated using thermal two-step ion-exchange are demonstrated. K⁺-Na⁺ ion-exchange process was first carried out in pure KNO₃ molten bath, and then field-assisted annealing (FAA) was used to make the buried waveguides. The effective buried depth is estimated to be ∼3.4 μm for the buried FAA waveguides. With the use of cut-back method, the fiber-to-guide coupling loss of ∼4.38 dB, the waveguide loss of ∼2.27 dB/cm, and Er³⁺ absorption loss ∼5.7 dB were measured for a ∼1.24-cm-long waveguide. Peak relative gain of ∼7.0 dB is obtained for a ∼1.24-cm-long waveguide. The potential for the fabrication of compact optical amplifiers operating in the range of 1520-1580 nm is also demonstrated.     

Amplification properties of Tb (III) green emission in polymeric waveguide doped with Tb-Al nanocluster

This paper describes optical amplification properties in a polymeric waveguide doped with Tb-Al nanoclusters. The Tb-Al nanocluster is a promising fluorescent material for polymeric waveguides, which can be uniformly dispersed in polymer matrices while restraining the concentration quenching of Tb³⁺. Under the continuous optical pumping by 488 nm laser light, optical amplification for the green emission of Tb³⁺ was achieved. The optical gain coefficients were estimated to be as high as 0.25 and 0.56 mm⁻¹ at the Tb-Al nanocluster concentrations of 4.5 and 5.0 wt%, respectively. Taking into account our previous works for the polymeric waveguide doped with Eu-Al nanocluster, the rare-earth-metal nanocluster is believed to be a promising candidate for various photonic applications such as multicolor polymer lasers and waveguide-type optical amplifiers.     

Yb3+sensitized Er3+-doped waveguide amplifiers: a theoretical approach

Silicate and phosphate glass waveguide amplifiers doped with Er³⁺, and co-doped with Er³⁺/Yb³⁺ are theoretically studied. Configurations for core and core–cladding doped waveguide amplifiers are considered. It is shown that gain in the core–cladding doped amplifiers is considerably higher than core doped amplifiers. It is also shown that with input signal power up to 1 and 200mW pump power, a 12.5dB gain can be achieved in a 3cm long waveguide amplifier, with a noise figure of 3dB.     

Tm and Tm-Tb-doped germanate glasses for S-band amplifiers

The mechanism involved in the Tm³⁺(³F₄)→Tb³⁺(⁷F_0,1,2) energy transfer as a function of the Tb concentration was investigated in Tm:Tb-doped germanate (GLKZ) glass. The experimental transfer rate was determined from the best fit of the ³F₄ luminescence decay due to the Tm→Tb energy transfer using the Burshtein model. The result showed that the 1700 nm emission from ³F₄ can be completely quenched by 0.8 mol% of Tb³⁺. As a consequence, the ⁷F₃ state of Tb³⁺ interacts with the ³H₄ upper excited state of Tm³⁺ slighting decreasing its population. The effective amplification coefficient β(cm⁻¹) that depends on the population density difference Δn=n(³H₄)-n(³F₄) involved in the optical transition of Tm³⁺ (S-band) was calculated by solving the rate equations of the system for continuous pumping with laser at 792 nm, using the Runge-Kutta numerical method including terms of fourth order. The population density inversion Δn as a function of Tb³⁺ concentration was calculated by computational simulation for three pumping intensities, 0.2, 2.2 and 4.4 kWcm⁻². These calculations were performed using the experimental Tm→Tb transfer rates and the optical constants of the Tm (0.1 mol%) system. It was demonstrated that 0.2 mol% of Tb³⁺ propitiates best population density inversion of Tm³⁺ maximizing the amplification coefficient of Tm-doped (0.1 mol%) GLKZ glass when operating as laser intensity amplification at 1.47 μm.     

Sm-doped polymer optical waveguide amplifiers

Trivalent samarium ion (Sm³⁺) doped SU8 polymer materials were synthesized and characterized. Intense red emission at 645 nm was observed under UV laser light excitation. Spectroscopic investigations show that the doped materials are suitable for realizing planar optical waveguide amplifiers. About 100 μm wide multimode Sm³⁺-doped SU8 channel waveguides were fabricated using a simple UV exposure process. At 250 mW, 351 nm UV pump power, a signal enhancement of ∼7.4 dB at 645 nm was obtained for a 15 mm long channel waveguide.     

Efficient blue upconversion emission due to confined radiative energy transfer in Tm-Nd co-doped Ta2O5 waveguides under infrared-laser excitation

Intense blue upconversion emission at 480 nm has been obtained at room temperature in Tm³⁺-Nd³⁺ co-doped Ta₂O₅ channel waveguides fabricated on a Si substrate, when the sample is excited with an infrared laser at 793 nm. The upconversion mechanism is based on the radiative relaxation of the Nd³⁺ ions (⁴F_3/2 → ⁴I_11/2) at about 1064 nm followed by the absorption of the emitted photons by Tm³⁺ ions in the ³H₄ excited state. A coefficient of energy transfer rate as high as 3 × 10⁻¹⁶ cm³/s has been deduced using a rate equation analysis, which is the highest reported for Tm-Nd co-doped systems. The confinement of the 1064 nm emitted radiation in the waveguide structure is the main reason of the high energy transfer probability between Nd³⁺ and Tm³⁺ ions.     

Broadband photoluminescence from pulsed laser deposited Er2O3 films

Photoluminescence (PL) with the bandwidth of 45 nm (1523-1568 nm at the level of 3 dB) was observed in amorphous Er₂O₃ films grown on to the quartz substrate by pulsed laser ablation of erbium oxide stoichiometric target. Optical transmission spectrum has been fitted to Swanepoel formula to determine the dispersion of refractive index and to extract resonance absorption peaks at 980 and 1535 nm. The maximum gain coefficient of 800 dB/cm at 1535 nm was estimated using McCumber theory and experimental spectrum of the resonance absorption. In 5.7 mm-long waveguide amplifier a theory predicts the spectral gain of 20 dB with 1.4 dB peak-to-peak flatness in the bandwidth of 31 nm (1532-1563 nm) when 73% of Er³⁺ ions are excited from the ground state to the ⁴I_13/2 laser level. Strong broadband PL at room temperature and inherently flat spectral gain promise Er₂O₃ films for ultra-short high-gain optical waveguide amplifiers and integrated light circuits.     

Optical parameters and upconversion fluorescence in Tm3+/Yb3+ codoped tellurite glass

Tm³⁺/Yb³⁺ codoped tellurite glass has been prepared. Density, refractive index, optical absorption, Judd-Ofelt parameters and spontaneous transition probabilities of Tm³⁺ have been measured and calculated, respectively. Intense blue three-photon upconversion fluorescence and S-band (1470 nm) fluorescence were investigated under the excitation of a 980 nm diode laser at room temperature. Judd-Ofelt parameters, strong blue three-photon upcoversion emission of Tm³⁺ in glass indicate that Tm³+/Yb³⁺ codoped tellurite glass is a promising blue color upconversion optical and laser material. In addition, experiment results showed the 980 nm laser was more efficient than 808 nm laser when pumping Tm³⁺/Yb³⁺ codoped tellurite glass, Tm³⁺/Yb³⁺ codoped tellurite glass also could be a promising material for S-band amplification.     

Integrated waveguide splitter fabricated by Cs-Na ion-exchange

This paper reports a optical power splitter fabricated by Cs⁺-Na⁺ ion-exchange in KF3 glass. The propagation loss of the waveguide is about 0.25 dB/cm derived from measured contrast ratio and 3 dB bandwidth.     

Broadband 2 μm emission and energy-transfer properties of thulium-doped oxyfluoride germanate glass fiber

High near-infrared transparency Tm³⁺-doped germanate bulk glass and fiber have been fabricated and 2 μm emission properties demonstrated. Energy-transfer processes in the germanate glass and fiber are discussed. The emission spectra are obtained from both bulk glass and fiber with the excitation of a 794 nm laser diode. The results indicate that the line width of the Tm³⁺:³F₄→³H₆ emission spectra measured in fibers is narrower than that of the bulk glass sample and shifts to longer wavelengths with increment of fiber length. The extended overlap integral method is used to calculate the microparameters of energy transfer and critical distance. A model is derived to better understand of the energy-transfer process of thulium ions in the germanate glasses responsible for emission at 2 μm. The study indicates that Tm³⁺-doped germanate fibers with a large core diameter has proved to be promising infrared optical and high-power level laser materials.     

Low-loss waveguides written with a femtosecond laser for flexible interconnection in a planar light-wave circuit

We describe a low-loss single-mode waveguide in planar light-wave circuit (PLC) glass doped with boron and phosphorus, which is more difficult to write than pure-silica glass. The written waveguide has a rectangular core, a symmetric near-field pattern, and a propagation loss of 0.35 dB/cm. The loss that originates from the mode-field mismatch between the mode-field diameters of the written and the PLC waveguides is less than 0.1 dB/point. In addition, we successfully connected PLC waveguides with a 500-microm-long waveguide written with a laser. The laser-written waveguide can flexibly connect PLC waveguides with a low coupling loss.     

Waveguiding and photoluminescence in Er-doped Ta2O5 planar waveguides

The optimization of erbium-doped Ta₂O₅ thin film waveguides deposited by magnetron sputtering onto thermally oxidized silicon wafer is described. Optical constants of the film were determined by ellipsometry. For the slab waveguides, background losses below 0.4 dB/cm at 633 nm have been obtained before post-annealing. The samples, when pumped at 980 nm yielded a broad photoluminescence spectrum (FWHM∼50 nm) centred at 1534 nm, corresponding to ⁴I_13/2-⁴I_15/2 transition of Er³⁺ ion. The samples were annealed up to 600 °C and both photoluminescence power and fluorescence lifetime increase with post-annealing temperature and a fluorescence lifetime of 2.4 ms was achieved, yielding promising results for compact waveguide amplifiers.     

Influence of surface effects on the performance of lead-niobium-germanate optical waveguides

Lead-niobium-germanate planar waveguides have been produced by pulsed laser deposition. The composition of the waveguides is found to be relatively weakly dependent on the laser fluence, while their surface morphology is affected dramatically. Smooth surfaces are obtained for a narrow fluence range centered at 2.0 J/cm², while particulates having typical diameters of <0.5 μm or droplets with typical diameters of <10 μm are observed at lower and higher fluences, respectively. The refractive index of the waveguides increases with fluence up to 2.1 at 2.0 J/cm², which is close to the value of the bulk glass, and remains constant at higher fluences. Propagation losses show instead a minimum (≈6.5 dB/cm) at 2.0 J/cm². The characteristics of the ablation process that leads to the ejection of solid particulates or molten droplets as well as the increase of the waveguides density on increasing the fluence are discussed to be responsible for the observed optical behavior.     

Influence of multimode-pump propagation on the gain characteristics of erbium–ytterbium doped waveguide amplifier

Channel waveguides with channel opening widths (COWs) from 4.5 to 7.5 μm with increment of 0.5 μm have been fabricated by two-step ion exchange on the same erbium-ytterbium uniformly doped phosphate glass substrate of 4.3-cm length. Experimental results indicate that the gain for 1534-nm small signal light pumped at saturation is maximized and shows a 3.6-dB enhancement for these erbium-ytterbium doped waveguide amplifiers (EYDWAs). The intensity profile overlap between signal and multimode-pump light in waveguide leads to the improvement in the gain of EYDWA. This can be used to explain the experimental results and shows the general dependence of the gain characteristics on the modal behavior of EYDWA. The presence of higher order modes of pump light and the optimization of this intensity profile overlap are significant to improve the gain properties of EYDWA.     

Role of Al2O3 in upconversion and NIR emission in Tm and Er codoped calcium fluoro phosphorous silicate glass system

In this study, the principal role of Al₂O₃ on the features of the photoluminescence spectra of Tm³⁺ ion and upconversion phenomenon in Tm³⁺ and Er³⁺ codoped CaF₂−Al₂O₃−P₂O₅−SiO₂ glass system has been investigated. The concentration of Al₂O₃ is varied from 2 to 10 mol% while that of Er³⁺ and Tm³⁺ is fixed. IR and Raman spectral studies have indicated that there is a gradual increase in the degree of disorder in the glass network with increase in the concentration of Al₂O₃ up to 6.0 mol%. This is attributed to the presence of Al³⁺ ions in octahedral positions in larger proportions. When the glasses are doped with Tm³⁺ ions, the blue and red emissions were observed, whereas in Er³⁺ doped glasses blue, green and red emissions were observed. When the glasses are codoped with Tm³⁺ and Er³⁺ ions and excited at 790 nm, all the three emission lines were observed to be reinforced, especially in the glasses mixed with 6.0 mol% of Al₂O₃. The IR emission band detected at about 1.8 μm due to ³F₄→³H₆ transition of Tm³⁺ ions is also observed to be strengthened due to codoping. The reasons for enhancement in the intensity of various emission bands due to codoping have been identified and discussed with the help of rate equations for various emission transitions.     

Low‐dose ion implanted active waveguides in Nd3+ doped near‐stoichiometric lithium niobate: promising candidates for near infrared integrated laser

By applying low‐dose oxygen ion implantation, active planar waveguides in Nd³⁺ doped near‐stoichiometric lithium niobate laser crystals have been, for the first time to our knowledge, successfully produced. The waveguide exhibits good transmission properties with relatively low propagation loss of ～2 dB/cm. The confocal micro‐luminescence investigations indicate that the emission properties of Nd³⁺ ions in the waveguide are well preserved with respect to the bulk, thus showing promising potentials for efficient waveguide laser action operating at the Nd³⁺ near‐infrared bands. (© 2008 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

High-gain Al2O3:Nd3+ channel waveguide amplifiers at 880 nm, 1060 nm, and 1330 nm

Neodymium-doped aluminum oxide films with a range of Nd³⁺ concentrations are deposited on silicon wafers by reactive co-sputtering, and single-mode channel waveguides with various lengths are fabricated by reactive ion etching. Photoluminescence at 880, 1060, and 1330 nm from the Nd³⁺ ions with a lifetime of 325 μs is observed. Internal net gain at 845–945 nm, 1064, and 1330 nm is experimentally and theoretically investigated under continuous-wave excitation at 802 nm. Net optical gain of 6.3 dB/cm at 1064 nm and 1.93 dB/cm at 1330 nm is obtained in a 1.4-cm-long waveguide with a Nd³⁺ concentration of 1.68×10²⁰ cm^?3 when launching 45 mW of pump power. In longer waveguides a maximum gain of 14.4 dB and 5.1 dB is obtained at these wavelengths, respectively. Net optical gain is also observed in the range 865–930 nm and a peak gain of 1.57 dB/cm in a short and 3.0 dB in a 4.1-cm-long waveguide is obtained at 880 nm with a Nd³⁺ concentration of 0.65×10²⁰ cm^?3. By use of a rate-equation model, the gain on these three transitions is calculated, and the macroscopic parameter of energy-transfer upconversion as a function of Nd³⁺ concentration is derived. The high internal net gain indicates that Al₂O₃:Nd³⁺ channel waveguide amplifiers are suitable for providing gain in many integrated optical devices.     

Population inversion between the H4 and the F4 excited states of Tm investigated by means of numerical solutions of the rate equations system in Tm-doped and Tm, Ho-codoped fluoride glasses

Population inversion between the ³H₄ and the ³F₄ excited states of Tm³⁺ ions responsible for the 1.5 μm emission in Tm³⁺ singly doped (0.5%) and Tm³⁺, Ho³⁺-codoped fluoride (ZBLAN) glasses and its dependence on the Ho³⁺ concentration (x=0.2-1%) was investigated by means of numerical solution of the rate equations system for continuous pumping at 797 nm. Mean lifetimes of donor and acceptor states were evaluated by using the integration method applied to the best fitting of fluorescence curves previously reported. Lifetime values were used to obtain the rate constants of all non-radiative energy-transfer processes involved and a complete set of rate equations better describing the observations was given. The rate equations were solved by numerical method and the population inversion between the ³H₄ and the ³F₄ excited states of Tm³⁺ was calculated to examine the beneficial effects on the gain associated with Ho³⁺ codoping. The results have shown that Tm³⁺ population inversion is reached only for high Ho³⁺-codoping (?0.3 mol%). Highest population inversion (∼1.6×10¹⁸ Tm³⁺ ions cm⁻³) was obtained in Tm(0.5%), Ho(1%)-codoped (ZBLAN) pumped by 2.8 kW cm⁻². This population inversion density is ∼6.4 times higher than that one observed in Tm:Tb:GLKZ, Tm:Tb:Ge-Ga-As-S-CsBr and Tm:Ho:Ge-Ga-As-S-CsBr for a similar pumping condition (∼2.5×10¹⁷ cm⁻³). In addition, Tm(0.5%):Ho(1%):ZBLAN presents the highest population inversion that linearly increases with the pumping intensity; this behavior does not show saturation effect at least for the maximum intensity of 12 kW cm⁻² employed. The use of 1 mol% of Ho³⁺-codoping maximizes the potential gain of Tm³⁺-doped (0.5%) ZBLAN to produce stimulated emission near 1.5 μm, making this material suitable for using it as fiber optical amplifier and/or fiber laser operating in 1.4-1.5 μm region of the spectrum.