Adsorptive Stripping Voltammetry of Rifamycins at Unmodified and Surfactant‐Modified Carbon Paste Electrodes

The electrochemical behavior of the antibiotics rifampicin and rifamycin SV is investigated by cyclic voltammetry at carbon paste and in situ surfactant modified carbon paste electrodes. Both antibiotics adsorb on the unmodified electrodes and show a reversible redox process due to the oxidation of the 6,9‐dihydroxynaphthalene moiety to the corresponding naphthoquinone. This process is used as analytical signal for developing adsorptive voltammetric methods for the determination of the antibiotics. Experimental parameters, such as pH of the supporting electrolyte, accumulation potential and time are optimized. After accumulation from acidic solutions (0.1 M KCl pH 2 or HCl 0.2 M) at ?0.1 or 0 V for 3 min, the differential pulse oxidation peak current changes linearly with the antibiotic concentration in the range 3.5×10^?10 M ?5.4×10^?9 M or 5×10^?11 M ?1.0×10^?9 M for rifampicin and rifamycin SV, respectively. Rifamycin SV is not accumulated on carbon paste electrodes modified in situ with the anionic surfactant sodium dodecyl sulfate, whereas rifampicin is readily accumulated on this modified electrodes resulting in a signal enhancement and allowing rifampicin determinations without interference from rifamycin SV. On the other hand, selective determination of rifamycin SV in the presence of rifampicin is achieved by using carbon paste electrodes in situ modified with the cationic surfactant cetyltrimethylammonium chloride.     

Iron(III) selective fluorescence probe based on perylene tetracarboxylic diimide

Responses of organic fluorophore, perylenediimide derivative N,N′-di[3-[2-(3-thienyl)ethyl]phenyl]perylene-3,4,9,10-bis-(dicarboxyimide) (PDI1) was investigated in polymer matrix of polyvinyl chloride (PVC) by emission spectrometry. Its response to Fe(III) ions was evaluated in terms of the effect of pH. The properties of time dependent response, reversibility, limit of detection, linear concentration range for the metal ion and repeatability characteristics of the sensing element also have been studied. The offered sensor exhibited remarkable fluorescence intensity quenching at pH 6.0 in the concentration range of 1 × 10^?6 to 2.5 × 10^?3 M Fe(III) ions. The reproducibility of the sensor membrane was investigated by alternately changing the solution between 1 × 10^?4 M Fe(III) in Na₂HPO₄ (4 × 10^?2 M) and NaH₂PO₄ buffer (2 × 10^?3 M).     

Electrosurface properties of microcrystalline cellulose dispersions in aqueous solutions of aluminum chloride, nitrate, and sulfate

The method of microelectrophoresis is employed to study the dependence of the ζ-potential of microcrystalline cellulose particles on the concentration (10^?6–10^?3 M) and pH (2–11) of aqueous aluminum chloride, nitrate, and sulfate solutions. It is shown that, in the absence of aluminum salts, the isoelectric point (IEP) of the particles is independent on the nature of acid anions and is observed at pH 3.2. The addition of aluminum salts in concentrations as low as 2 × 10 ^?6 M for chloride and nitrate and 1 × 10^?5 M for sulfate causes a shift of IEP to a less acidic region (pH 3.8), the value of which is virtually independent of the nature of the salt. As the concentration of salts is increased, the ζ-potential becomes positive, rises with an increase in pH to a maximum magnitude at pH 5.0–6.0, and decreases further until the second IEP (pH ～ 6.5–7.0) is reached. At higher pH values, the ζ-potential becomes negative again. The observed ζ(pH) dependences are explained by the formation of hydrolyzed aluminum species exhibiting different adsorbabilities on microcrystalline cellulose particles. It is shown that positively charged hydroxocomplexes formed in aluminum sulfate solutions are characterized by a lower adsorbability than hydroxocomplexes formed in chloride and nitrate solutions.     

The application of 2,4,6-trinitrobenzene-1-sulphonic acid in the differential pulse polarographic determination of amines

The differential pulse polarographic behaviour of 2,4,6-trinitrophenyl (TNP) derivatives of several primary amines and amino acids was investigated in the presence of sulphite ion. All the derivatives produced a polarographic peak for their complexes with sulphite (1 × 10^?2 M) in pH 8.0 phosphate buffer (0.05 M)/0.1 M potassium chloride. The derivatives of proteins and peptides did not give such a peak. A 5-min reaction time at room temperature (or 50°C for lysine) and pH 10.5 using 1 × 10^?4 M 2,4,6-trinitrobenzene-1-sulphonic acid provides the optimal conditions for the determination of 5 × 10^?6?2.5 × 10^?5 M amines. The relative standard deviation for determining 1 × 10^?5 M glycine (n = 5) was 1%.     

Sodium ion-selective membrane electrode based on a new crown ether

A sodium ion-selective PVC membrane electrode based on di(o-methoxy)stilbenzo-24-crown-8 is reported. The electrode gives a near-Nernstian response in the range 9×10^?6–1×10^?2 M sodium ion and can be used in the pH range 5–8.5. Selectivity coefficients are 1.8×10^?1 (K⁺), 2.0×10^?4 (Li⁺) 2.5×10^?2 (NH⁺₄) and about 10^?4 for Mg²⁺, Ca²⁺ and Ba²⁺.     

Kinetic investigation on the oxidation of nitrite by oxochromium(V) ion in aqueous and micellar systems

The kinetics of oxidation of nitrite by [O = Cr^V (5‐chlorosalen)]⁺ complex has been studied spectrophotometrically at [Cr^V] = 0.5 × 10^?3 M, [NO₂^?] = 0.01–0.1 M, [H⁺] = 0.0001–0.05 M, I = 0.15 M, and T = 25°C in the presence of cationic surfactant, cetyl pyridium chloride (CPC), and anionic surfactant, sodium dodecyl sulfate (SDS),in aqueous acidic medium. The oxygen atom transfer reaction from O = Cr^V to nitrite ion is influenced by the ionic nature of the micelle. The redox reaction is accelerated in presence of CPC and slowed down by 40 times in presence of SDS. The mechanism of the reaction involves an inner‐sphere process involving the formation of an intermediate followed by oxo transfer process. © 2003 Wiley Periodicals, Inc. Int J Chem Kinet 36: 79–86 2004     

Trace Analysis of Al (III) Ions Based on the Redox Current of a Conducting Polymer

A conducting polymer was electrochemically prepared on a Pt electrode with newly synthesized 3′‐(4‐formyl‐3‐hydroxy‐1‐phenyl)‐5,2′ : 5′,2″‐terthiophene (FHPT) in a 0.1 M TBAP/CH₂Cl₂ solution. The polymer‐modified electrode exhibited a response to proton and metal ions, especially Al(III) ions. The poly[FHPT] was characterized with cyclic voltammetry, EQCM, and applied to the analysis of trace levels of Al(III) ions. Experimental parameters affecting the response of the poly[FHPT] were investigated and optimized. Other metal ions in low concentration did not interfere with the analysis of Al(III) ions in a buffer solution at pH 7.4. The response was linear over the concentration range of 5.0×10^?8–7.0×10^?10 M, and the detection limit was 5.0×10^?10 M using the linear sweep voltammetry (LSV). Employing the differential pulse voltammetry (DPV), the response was linear over the 1.0×10^?9–5.0×10^?11 M range and the detection limit was 3.0×10^?11 M. The relative standard deviation at 5.0×10^?11 M was 7.2% (n=5) in DPV. This analytical method was successfully verified for the analysis of trace amounts of Al(III) ions in a human urine sample.     

Nanobiocomposite Modified Carbon‐Ceramic Electrode Based on Nano‐TiO2‐Plant Tissue and Its Application for Electrocatalytic Oxidation of Dopamine

A new modified carbon‐ceramic electrode was prepared by incorporating TiO₂ nanoparticle into sol‐gel network by accompanying apple tissue. A mixture of fine graphite powder with 15 wt% of TiO₂ nanoparticle was used for the preparation of the carbon matrix and finally modification with a known amount weighted of apple tissue. The apple tissue containing polyphenol oxidase enzyme acts as molecular recognition element. The electrocatalytic oxidation of dopamine was investigated on the surface of the nanobiocomposite modified carbon‐ceramic electrode using cyclic voltammetry, chronoamperometry and amperometry techniques. Effect of pH, scan rate, TiO₂ percentage on the response of modified electrode was studied. The prepared modified electrode presented a linear range for dopamine from 5.0×10^?6 to 1.2×10^?3 M in buffered solutions with pH 7.4 by amperometry. The detection limit was 3.41×10^?6 M dopamine. The response of the modified carbon‐ceramic electrode and unmodified carbon‐ceramic electrode was compared.     

Novel Poly(ethylene glycol)s Bearing Tributyltin Carboxylate End Groups as Ionophores in the Development of Chloride Ion‐Selective Electrodes

The potentiometric response characteristics of electrodes based on PVC membranes containing novel polyethylene glycols (PEGs) with tributyltin carboxylate end groups as ionophores for chloride ions were studied in 0.1 M HEPES solution, at the spontaneous pH. The effects of solvent mediator, amount of cationic additive, amount of ionophore and PEG chain length on the behavior of the sensors were investigated. The membranes with the best composition responded to chloride concentration in a linear range from 10^?4 to 10^?1 M Cl^? with a nearly Nernstian slope and a detection limit of 6.5×10^?5 M. The sensor showed a short response time (<25 s) in the whole concentration range and an operational lifetime of about one week for the most performing PVC membranes. In comparison with ISEs based on anion exchangers the interferences from the more lipophilic anions were greatly reduced, as inferable by the selectivity coefficients determined with the matched potential method at chloride concentration of 3.0×10^?3 M.     

Determination of Tetracycline by Microdroplet Hydrodynamic Adsorptive Voltammetry Using a Multiwalled Carbon Nanotube Paste Rotating Disk Electrode

A novel and simple method is proposed for the determination of tetracycline by adsorptive voltammetry in a droplet using a carbon nanotube paste rotating disk electrode (CNTP-RDE). An enhanced electrochemical oxidation response of tetracycline was observed in pH 8.2 supporting electrolyte by the addition of a long-chain cationic surfactant, such as benzyldimethyltetradecylammonium chloride (zephiramine). Under the optimized experimental conditions, the calibration curve was linear across a tetracycline concentration range from 1.0?×?10^?7 to 2.0?×?10^?6 M. The limit of detection and sensitivity were 4.0?×?10^?8 M and 0.9358?A M^?1, respectively. This method was successfully employed for the determination of tetracycline in milk samples.     

A multivariate calibration procedure for the tensammetric determination of detergents

A multivariate calibration procedure based on singular value decomposition (SVD) and the Ho-Kashyap algorithm is used for the tensammetric determination of the cationic detergents Hyamine 1622, benzalkonium chloride (BACl), N-cetyl-N,N,N-trimethylammonium bromide (CTABr) and mixtures of CTABr and BACl. The sensitivity and accuracy depend strongly on the nature of the detergent. Acceptable accuracy is obtained with a two-step calculation procedure in which calibration constants for the total concentration range of interest are used to guide the choice of a more specific set of calibration constants which are valid for a much smaller concentration span. For Hyamine 1622, concentrations in the range 5 × 10^?6?2 × 10^?4 M could be determined with an accuracy of ± 10^?6 M. For CTABr, these numbers were 3 × 10^?6?2 × 10^?4 M and ± 5 × 10^?7 M; for BACl, they were 2 × 10^?3?9 × 10^?2 g l^?1 and ± 1 × 10^?3 g l^?1. In the mixtures of CTABr and BACl, the accuracies were ± 3 × 10^?6 M and × 1 × 10^?3 g l^?1, respectively.     

Inhibition of Emulsin by D-Gluconhydroximo-1,5-lactone and Related Compounds

At pH 4.5 (citrate buffer), D -gluconhydroximo-lactone ( 2 ), the N-methylurethane 3 and the N-phenylurethane 4 inhibit competitively the hydrolysis of p-nitrophenyl β-D -glucopyranoside by emulsin. The IC₅₀ values of 2, 3 , and 4 were 1.6 × 10^?4, 1.0 × 10^?4, and 5.8 × 10^?6 M , respectively. The K_i values of 2 and 4 were 9.8 × 10^?5 and 2.3 × 10^?6 M , respectively, while D-glucono-1,5-lactone ( 1 ) showed IC₅₀ = 1.1 × 10^?4 M and K_i = 3.7 × 10^?5 M .     

Cathodic and Adsorptive Stripping Votammetry of Naftazone

Abstract

Naftazone (1,2-naphthoquinone-2-semicarbazone) undergoes a reversible two-electron transfer in both acidic and alkaline solutions and also gives rise at pH > 7 to an anodic wave attributed to the formation of a mercury derivative. Cathodic stripping voltammetry is proposed to determine the compound down to 5 × 10^?9 M after accumulation of its mercury salt formed at -0.05V in a 0.05M sodium hydroxide solution. These results have been compared with those obtained by performing an adsorptive collection of the drug in a pH 3 sodium perchlorate solution. Concentrations ranging from 1 × 10^?7 to 2 × 10^?7M can be easily investigated, the detection limit being 7 × 10^?11M. The influence of several operational parameters has also been considered.     

Voltammetric Determination of Epinephrine with a 3‐Mercaptopropionic Acid Self‐Assembled Monolayer Modified Gold Electrode

Epinephrine (EP) could exhibit an anodic peak at a bare gold electrode, but it was very insensitive. However, when the bare gold electrode was modified with 3‐mercaptopropionic acid (3MPA) self‐assembled monolayer (3MPA SAM), the peaks of EP became more reversible and sensitive due to the accumulation and mediate efficiency of 3MPA SAM. Conditions such as solution pH, concentration of supporting electrolyte and accumulation time were optimized. Under the selected conditions (i.e., 0.02 M pH 6.8 sodium phosphate buffer, accumulation time: 2 min under open‐ circuit.), the height of the anodic peak at about 0.18 V (vs. SCE) was linear to EP concentration in the range of 2×10^?7 ?1×10^?6 M and 1×10^?6?5×10^?4 M with correlation coefficient of 0.995 and 0.999, respectively. When the 3MPA/Au was further modified with cysteamine, the interference of H₂O₂ and BrO₃^? was eliminated. But the resulting electrode still suffered from the interference of ascorbic acid. This method was used to determine the content of EP in adrenaline hydrochloride injections, and the recovery was in the range of 97.0% to 105.1%.     

The kinetics of reduction of palladium (II) complexes with β-alanine at dropping mercury electrode and the complexes’ stability constants

By using dc and ac polarography, the kinetics of electroreduction of the palladium (II) complexes with β-alanine at a dropping mercury electrode was studied in solutions with the palladium (II) concentration from 2 × 10^?5 to 2 × 10^?4 M and variable β-alanine and sodium perchlorate concentrations (pH 6–12). One polarographic wave was observed in solutions with pH 9 and 10 at the β-alanine overall concentration of c _βala = 1 × 10^?3 to 5 × 10^?2 M; two waves, at lower pH or higher c _βala. It was concluded on the formation of different forms of palladium (II) complexes in the studied solutions; the complexes contained two to four β-alanine coordinated anions. Using the limiting diffusion currents for the two waves at pH 9–11 and c _βala = 0.1 and 0.5 M, the stepwise stability constant for the Pd(βala) ₄ ^2? complex was calculated. Using two ac peaks observed at pH 7–8 and c _βala = 1 × 10^?2 to 0.1 M, the stepwise stability constant for the Pd(βala) ₃ ^? . was calculated. The perchlorate ions adsorbed at the dropping mercury electrode, as well as βala^? anions at their higher concentrations, hamper the electroreduction of the palladium (II) complexes with β-alanine.     

Iodide‐Selective Electrodes Based on Bis[N(2‐methyl‐phenyl) 4‐Nitro‐thiobenzamidato]mercury(II) and Bis[N‐phenyl 3,5‐Dinitro‐thiobenzamidato]mercury(II) Carriers

Highly selective poly(vinyl chloride) (PVC) membrane electrodes based on recently synthesized mercury complexes including Hg(Nmpntb)₂ and Hg(Npdntb)₂ as new carriers for iodide‐selective electrodes by incorporating the membrane ingredients on the surface of graphite electrodes are reported. The effect of various parameters including the membrane composition, pH and possible interfering anions were investigated on the response properties of the electrodes. Both sensors exhibited Nernstian responses toward iodide over a wide concentration range of 7×10^?7 to 0.1 M and 1×10^?6 to 0.1 M, with slopes of 59.6±0.8 and 58.9±0.9 mV per decade of iodide concentration and detection limit of 3×10^?7 M and 7×10^?7 for Hg(Npdntb)₂ and Hg(Nmpntb)₂, respectively, over a wide pH range of 3–11. The sensors have response times of ≤5 s and can be used for at least 2 months without any considerable divergence in their potential response. The proposed electrodes show good ability to discriminate iodide over several inorganic and organic anions. The electrodes were successfully applied to direct determination of iodide in synthetic mixture, waste water and drinking water and as indicator electrodes in precipitation titrations.     

Enhanced Electrochemiluminescence of TiO2 Nanoparticles Modified Electrode by Nafion Film and Its Application in Selective Detection of Dopamine

In this work, a simple and effective approach to obtain stable, nontoxic and strong electrochemiluminescence (ECL) interfaces is provided by coating TiO₂ nanoparticles (NPs) modified glassy carbon electrode (GCE) surfaces with Nafion. Unlike a decrease of the current resulting from the blocked diffusion usually displayed in electrochemical processes by Nafion coating, a Nafion/TiO₂ NPs modified electrode not only shows a highly stable ECL, but also shows an 8‐fold increase of ECL intensity and a reduction of the overpotential of ca. 300 mV in the presence of K₂S₂O₈ as co‐reactant, compared with those of bare TiO₂ NPs modified electrodes. The roles of Nafion coating on TiO₂ NPs in the ECL process are proposed to be twofold: to provide refuge for the free radicals and to enhance the electron‐hole recombination. Benefiting from its excellent ECL performance, the cationic exchange function of Nafion and the susceptible to being oxidized performance of dopamine (DA) by holes, the Nafion/TiO₂ composite electrode could be used to sensitively and selectively detect DA with a detection limit of 1.0×10^?11 M and a linear range of 1.0×10^?11–6.0×10^?7 M. The coexisting anionic species such as excess ascorbic acid show little interference on DA detection.     

Solvent Extraction of Vanadium with α-Benzoin Oxime

The solvent extraction of vanadium by a chloroform solution of α-benzoin oxime was investigated. The most favorable condition for the extraction has been found in the pH rang of 1.8 to 3.0 in sulfate or chloride buffer solutions, but with better extraction efficiency when sulfate was used. A solution of 2×10^?2 M α-benzoin oxime in chloroform was used, and 1×10^?4 to 2×10^?2 M vanadium(V) was extracted favorably in about 89% yield by a single extraction, and in about 97% yield by a double extraction. The effects of shaking time, concentration of α-benzoin oxime, and diverse ions have also been investigated. Vanadium(V) can be readily extracted without interference in the presence of copper(II), aluminum(III), iron(III), silver(I), zirconium(IV), and chromium(III).     

Spectrophotometric determination of titanium with Chrome Azurol S (or Eriochrome Cyanine R) in the presence of some cationic surfactants

A new sensitive spectrophotometric method for titanium determination, based on the ternary Ti-Chrome Azurol S (CAS)-cetyltrimethylammonium (CTA) system, was developed. The molar absorptivity is 7.3 × 10⁴ liters mol^?1 cm^?1 at λ_max = 565 nm. The maximum absorbance is attained in 5 min at pH 1.3 ± 0.1 and at CAS and CTA concentrations of 1.5 × 10^?4 and 5 × 10^?4M, respectively. Zirconium and hafnium in the presence of ascorbic acid are the only interfering metals. Hydrogen peroxide and EDTA interfere with the titanium determination as well. The proposed method was applied to the determination of titanium (about 1 × 10^?2%) in aluminum metal. The method, based on the Ti-Eriochrome Cyanine R-CTA system, is similar to the above method. Among other cationic surfactants, cetylpyridinium chloride (CP) and zephiramine were examined. The color effects when using CP, and especially zephiramine, are worse than in the presence of CTA.     

Kinetic studies on the metal(II) tartarate–peroxomonosulfate reaction

The kinetics of oxidation of tartaric acid (TAR) by peroxomonosulfate (PMS) in the presence of Cu(II) and Ni(II) ions was studied in the pH range 4.05–5.20 and also in alkaline medium (pH ～12.7). The rate was calculated by measuring the [PMS] at various time intervals. The metal ions concentration range used in the kinetic studies was 2.50 × 10^?5 to 1.00 × 10^?4 M [Cu(II)], 2.50 × 10^?4 to 2.00 × 10^?3M [Ni(II)], 0.05 to 0.10 M [TAR], and µ = 0.15 M. The metal(II) tartarates, not TAR/tartarate, are oxidized by PMS. The oxidation of copper(II) tartarate at the acidic pH shows an appreciable induction period, usually 30–60 min, as in classical autocatalysis reaction. The induction period in nickel(II) tartarate is small. Analysis of the [PMS]–time profile shows that the reactions proceed through autocatalysis. In alkaline medium, the Cu(II) tartarate–PMS reaction involves autocatalysis whereas Ni(II) tartarate obeys simple first‐order kinetics with respect to [PMS]. The calculated rate constants for the initial oxidation (k₁) and catalyzed oxidation (k₂) at [TAR] = 0.05 M, pH 4.05, and 31°C are Cu(II) (1.00 × 10^?4 M): k₁ = 4.12 × 10^?6 s^?1, k₂ = 7.76 × 10^?1 M^?1s^?1 and Ni(II) (1.00 × 10^?3 M): k₁ = 5.80 × 10^?5 s^?1, k₂ = 8.11 × 10^?2 M^?1 s^?1. The results suggest that the initial reaction is the oxidative decarboxylation of the tartarate to an aldehyde. The aldehyde intermediate may react with the alpha hydroxyl group of the tartarate to give a hemi acetal, which may be responsible for the autocatalysis. © 2011 Wiley Periodicals, Inc. Int J Chem Kinet 43: 620–630, 2011