微穿孔介电弹性体薄膜的吸声性能试验分析*

针对普通薄膜型降噪结构的吸声性能较差和吸声带宽较窄的问题,本文设计了一种微穿孔的介电弹性体薄膜吸声结构。该结构由穿孔的介电弹性体薄膜与背腔组合而成,目的是拓宽介电弹性体薄膜低频率段的吸声带宽。针对微穿孔的介电弹性体薄膜吸声结构,从试验角度分析穿孔薄膜初始厚度、穿孔孔径及穿孔间距对结构吸声性能的影响。分析结果可知：通过适当增加薄膜的初始厚度,薄膜的整体吸声性能得到有效提升,最大可将319Hz吸声频带的吸声系数从0.2提升至0.7;减小薄膜的穿孔孔径能够有效拓宽穿孔薄膜的吸声频带,可使吸声系数0.4以上的吸声带宽由304Hz拓宽至432Hz;适当控制穿孔间距能够达到更好的吸声效果。     

Laser-induced fabrication of randomly distributed nanostructures in fused silica surfaces

The nanostructuring of dielectrics is a big challenge for laser patterning methods. In this study a novel laser structuring method for the fabrication of randomly distributed nanostructures, called laser-induced front side etching using in situ pre-structured metal layers (IPSM-LIFE), is presented. The pulsed laser irradiation of a thin metal film deposited onto a dielectric substrate with fluences below the ablation threshold results in the formation of randomly distributed metal structures by self-assembly processes. Further pulsed laser irradiation of these metal structures with higher or equal laser fluences causes the formation of complex patterns at the surface of the dielectric due to localized ablation and melting processes of the dielectric surface induced by the absorption of the laser energy by the metal structures and the local energy transfer into the dielectric surface. The pattern formation observed in the film and the dielectrics substrate after irradiation of 10 nm chromium layers on fused silica, with laser pulses (Δt _p =25 ns, λ=248 nm), was studied by scanning electron microscopy (SEM) and atomic force microscopy (AFM). Different features with a lateral size down to a few tens of nanometers, like concentric ring patterns, donut-like structures, and bar patterns were observed at the dielectric.     

表面等离子共振效应中传统近似理论与薄膜光学理论

指出Kretschmann模型的传统表面等离子共振公式在求解金属薄膜的参量时存在近似性,采用更为严密的薄膜光学理论,通过薄膜膜系的特征矩阵,得出表面等离子体共振衰减曲线.结果表明,表面等离子体共振近似理论与薄膜光学理论得到的共振角及反射率幅度存在差别;采用等高线图,给出了共振角差随着金属介电常量的变化规律.进一步的实验表明,薄膜光学理论所得模拟结果较表面等离子体共振近似理论与实验值吻合地更好,证明薄膜光学理论应用在表面等离子体共振效应要优于常用的近似理论.最后,采用两种理论对表面等离子体共振传感器进行优化设计,结果表明,两种理论所获得的高灵敏度分布区域差异较大,必须采用薄膜光学理论提供更精确的薄膜参量,来优化设计高灵敏度表面等离子体共振传感器.     

Optical properties of composite thin films containing silver nanoparticles

Absorption and reflection of electromagnetic radiation by a composite thin film consisting of a transparent dielectric matrix with inclusions of metal nanoparticles of radius much less than the wavelength were theoretically investigated based on the Maxwell–Garnett model. The absorption, reflection, and transmission of optical radiation in such a dielectric composite film were analyzed using effective optical parameters for the refractive index and absorption coefficient that depended on the nanoparticle size.     

The effect of cesium metal clusters on the optical properties of cesium iodide thin films

Cesium metal clusters strongly affect the optical properties of cesium iodide thin films. The metal clusters are formed during film formation by thermal evaporation. The cesium cluster of 30–40 nm in the matrix of cesium iodide insulating thin films results in Surface Plasmon Resonance (SPR). The peak position of these SPR peaks showed a red shift. This was shown to be due to changes in the dielectric constant of CsI resulting from the strains in the films caused by the metal clusters themselves.     

Hot electrons and laser optoacoustics in metal nanoparticles

The theory of sound generation and heat transfer in matrix-embedded metal nanoparticles under ultra-short laser irradiation has been developed. The shape and time dependence of acoustic waves generated by a sharp change in the pressure of electrons have been investigated for a single nanoparticle and for the group of nanoparticles located on a 2-D flat matrix plane. The dependence of the electronic temperature and the temperature of the interface between the dielectric matrix and nanoparticle as a function of time has been derived.     

Semicylindrical acoustic transducer from a dielectric elastomer film with compliant electrodes

A semicylindrical acoustic transducer was constructed using a dielectric elastomer film with compliant electrodes that is an electroactive polymer composed of a polyurethane elastomer base and polyethylene dioxythiophene/polystyrene sulfonate electrodes. The use of this dielectric elastomer is advantageous because polyurethane is a common material that keeps its shape without any rigid frame. Because the dielectric elastomer films are essentially incompressible, electric-field-induced thickness changes are usually translated into much larger changes of the film area and side length. Here it is proposed that this change in side length can be utilized for sound generation when the film is bent into a semicylindrical shape. Accordingly, a semicylindrical acoustic transducer was fabricated using a film of thickness of 300 μm and its acoustic characteristics were investigated. The transducer can be operated at low applied voltages by reducing the film thickness, as long as the film is thick enough to generate sufficient force to overcome sound radiation impedance. The second harmonic distortion of the transducer was also investigated as a function of the ratio of the direct current bias voltage to the alternating current audio signal amplitude.     

Laser short-pulse heating of silicon-aluminum thin films

Energy transport in silicon-aluminum thin films is examined during the laser short-pulse irradiation subjected to the silicon film. The silicon film is considered to be at the top of the aluminum film. Thermal boundary resistance at the interface of the films is incorporated in the analysis. The absorption of laser radiation in the silicon and aluminum films is modeled using the transfer matrix method. Since the silicon film is dielectric, the phonon radiative transport basing the Boltzmann transport equation is incorporated to determine equivalent equilibrium temperature in the film while modified two-equation model is used to account for the non-equilibrium energy transport due to thermal separation of electron and phonon sub-systems in the aluminum film during the laser short-pulse heating process.     

Nonlinear optical properties of composites based on conductive metal-alkanoate liquid crystals

The dynamic holography in new composite materials based on a novel class of metal-alkanoate ionic liquid crystals (ILCs) is studied experimentally and theoretically. The composites are formed as a dielectric dye film covered by lyotropic metal-alkanoate ILC and ionic smectic glasses with doped dye molecules. The dynamic gratings are created by nanosecond pulses of double frequency Nd:YAP laser, the recording demonstrates fast erasure time of residual thermal gratings. The nonlinear optical properties are determined by the resonance nonlinearity in photosensitive centres of ILC. Note, that permanent relief gratings will be formed on a dielectric dye film only as well as in composite cells either with nematic LC or with polymers under action of pulsed laser radiation. Lyotropic ILC layer applied over the dye film provides the dynamic regime of grating recording in composite cells. We found a secondary thermal grating is much smaller, the conductive ILC matrix provides effective heat dissipation and erasure of this thermal grating. A theory of Raman-Nath self-diffraction holography on thin films followed from the wave equation and the nonlinear mechanism of absorption saturation is developed to explain experimental results.     

Distributed-feedback vertical cavity structures for optically pumped solid-state organic lasers

Theoretical analysis of threshold gain and absorption efficiency is presented for a vertical-cavity surface-emitting organic laser by using transfer matrix method. Pyrromethene 567 dye doped in a polymer film is examined for verification of the active material with an InGaN cyan LED as a pump source. By alternately stacking high- and low-refractive-index active polymer films, modeling results indicate that the threshold gain can be reduced and the absorption efficiency at the pump wavelength can be improved compared with those of a vertical cavity with a dielectric mirror stack. The absorption efficiency of the distributed-feedback resonator is not practically degraded even if the pump wavelength is located near the stopband.     

Temperature profile of the multilayer structure irradiated by pulsed laser

Two programs are developed to calculate the temperature profile, as well as the reflectance, transmittance and absorption of a given multilayer film structure, in order to better understand the laser energy distribution between the reflectance, transmittance and absorption in each film layer. An inorganic Blu-ray recordable disc (BD-R) structure is used as a practical demonstration of the multilayer structure. The reflectance and absorption of the BD-R structure exhibit opposite trends and oscillate repeatedly with varying lower or upper dielectric layer thickness while the rest of the film thickness remains unchanged. The energy absorption in an absorbed layer depends on the thickness of the dielectric layers, its relative position in the structure and the extinction coefficient of its optical constant. The total absorption ratio of its maximum to minimum can be over 3 when changing the lower dielectric layer thickness of the studied structure. The layer thickness acts as an energy valve to control the energy flow into the multilayer structure. The thermal profile of the multilayer film structure irradiated by a pulsed laser is calculated at different positions in the film layers with time. The calculated temperatures in the recording alloy layer exhibit linear relationship with the applied power level. The effect of the laser duration time on the temperature increase in the recording layer is significant in the first few nanoseconds and becomes saturated if the heat balance is established in the structure. The calculated temperature is consistent with the experimental recording result when the structure is recorded at 4-time BD-R recording speed.     

Interaction of an intense laser field with a dielectric containing metallic nanoparticles

In order to understand the role played by nanodefects in optical breakdown of dielectrics, the interaction of an intense laser field with model dielectric samples containing metallic nanoparticles is studied both theoretically and experimentally. A theoretical study of the metal conduction electrons dynamics in the laser field predicts an efficient injection of carriers from the metallic inclusion to the conduction band of the dielectric, which leads to a strong local increase of the optical absorption in the initially transparent matrix. This prediction is tested experimentally by using time-resolved spectral interferometry to measure excitation densities as a function of the laser intensity in silica samples doped with gold nanoparticles, which are compared with similar measurements in pure silica. PACS 61.80.Ba; 42.70.-a; 78.47.+p     

Metal clusters and nanoparticles in dielectric matrices: Formation and optical properties

The optical properties of thin dielectric films with metal inclusions and their dependence on thermal and laser annealing are studied experimentally. Metal clusters (Ag, Au, and Cu) in dielectric materials (Al₂O₃ and SiO₂) are obtained by simultaneous vacuum deposition of metal and dielectric on the surface of a corresponding dielectric substrate (sapphire and quartz). It is shown that, depending on the deposited dielectric material, on the weight ratio of deposited metal and dielectric, and on the subsequent thermal treatment, one can obtain different metal structures, from clusters with a small number of atoms to complex dendritic plasmonic structures.     

Optical properties of a semiconductor in the exciton spectral region under exposure to a high-power pump pulse in the <Emphasis Type="Italic">M</Emphasis>-band region

The behavior of the dielectric susceptibility of a semiconductor is studied in the case where the exciton state is probed by weak-pulse photons in the presence of a high-power laser pulse in the region of the M band of CuCl luminescence. A pronounced Autler-Townes effect for the exciton transition is shown to occur. The absorption peak position is determined by the amplitude and frequency of the pump field.     

Light emission from Ag cluster films excited by conduction current

The light emission spectra obtained for a silver cluster film, excited by the passage of electrical current through it, were measured by the charge‐coupled device (CCD) combined with a monochromator in the spectral range 200 ≑ 1050 nm (6.2 ≑ 1.18 eV). This film is a two‐dimensional ensemble of Ag clusters linked by tunneling on a dielectric substrate. It was shown that the light emission spectra had a number of features, and the shape of spectrum depends on a voltage applied to the film. With increasing the voltage the spectrum starts to extend to high energies. The light emission in the visible spectral region was observed already at 1 V applied to the film, i.e., the photon energy can exceed the excitation energy. It means that this phenomenon is not trivial. In order to explain these results, an assumption about the electron gas heating in metal clusters may be used.     

金属杂质粒子诱导薄膜的损伤机理研究

薄膜内的杂质粒子极易诱导薄膜损伤,研究了金属粒子诱导HfO₂薄膜损伤的特征,并基于金属粒子的热力学过程进行了分析。金属粒子对激光的强烈吸收将引起薄膜的熔化、气化以及电离,从而引起薄膜的剥离和脱落,形成圆状坑点;金属粒子对激光的吸收、热扩散以及热膨胀效应与其尺寸等密切相关;从温升规律分析,在相同激光能量辐照下,粒子大小引起的温升不同,从而形成大小不一的点坑状破坏点,且存在一个温升效应最强的粒径,最易引起薄膜的损伤;从金属粒子激光等离子体的辐射效应分析,金属粒子的辐射谱主要集中在紫外部分,辐射光子能量比入射激光光子能量强,具有更强的电离能力,从而加剧了薄膜的去除。     

Generation of acoustic waves by power microwave pulses with the use of thin metal films

We study the features of excitation of acoustic waves by high-power microwave pulses in thin metal films bordering on liquid. Aluminum films with thicknesses 1–10 nm deposited onto a quartz substrate were used in experiments. It is shown theoretically that the absorption coefficient of microwaves is maximum for film thickness from 2 to 3 nm and the value of this maximum is determined by the dielectric permittivity of the bordering liquid. Theoretical calculations and experiments are performed for water and ethyl alcohol. The sound generation in a layered system quartz-aluminum film-liquid is analyzed with the help of the step-by-step approach. At the first step, microwave energy is absorbed in the film and heat is released. Then heat almost instantly diffuses into a liquid whose thermal expansion creates an acoustic signal. Profiles of acoustic signals excited in aluminum films by microwave pulses with a 5-ns duration and an energy of up to 1 mJ are experimentally detected. The most efficient transduction was observed for an aluminum film 3.5 nm thick.     

Structural and magnetic characterization of LaSrMnO3 thin films deposited by laser ablation on MgO substrates

La_2/3Sr_1/3MnO_3?δ thin films were deposited by laser ablation on MgO substrates under low oxygen pressure cool down. Their structural and magnetic properties are presented. The magnetic and electrical resistivity measurements indicate a reduction of the Curie and the metal–insulator transition temperatures due to the formation of magnetic inhomogeneneous films, where clusters of a metallic phase are mixed in a magnetically disordered insulating matrix. By a low-angle X-ray reflectivity study we show that the thin films are chemically inhomogeneous with an oxygen deficiency in bulk of the film when compared with the film/air interfacial region.     

Design of near-unity transmittance dielectric/Ag/ITO electrodes for GaN-based light-emitting diodes

We designed a near-unity transmittance dielectric/Ag/ITO electrode for high-efficiency GaN-based light-emitting diodes by using the scattering matrix method. The transmittance of an ultrathin metal layer, sandwiched between a dielectric layer and an ITO layer, was investigated as a function of the thickness and the optical constant of each constituent layer. Three different metals (Ag, Au, and Al) were examined as the metal layer. The analytical simulation indicated that the transmittance of a dielectric/metal/ITO multilayer film is maximized with an approximately 10-nm-thick Ag layer. Additionally, the transmittance also tends to increase as the refractive index of the upper dielectric layer increases. By tailoring the thickness of the dielectric layer and the ITO layer, the dielectric/Ag/ITO structure yielded a transmittance of 0.97, which surpasses the maximum transmittance (0.91) of a single ITO film. Furthermore, this extraordinary transmittance was present for other visible wavelengths of light, including violet and green colors. A complex phasor diagram model confirmed that the transmittance of the dielectric/metal/ITO multilayer film is influenced by the interference of reflected partial waves. These numerical findings underpin a rational design principle for metal-based multilayer films that are utilized as transparent electrodes for the development of efficient light-emitting diodes and solar cell devices.     

基模磁激元诱导的多带完美吸收

本文提出一种方向不敏感多带吸收的新结构,即结合光学声子色散材料及无色散介电材料,将其作为单一尺寸金属/介质/金属微光栅的介质分离层。在红外大气窗口波段激发了基模磁激元谐振因此导致多频带吸收。基于有限元方法求解了混合结构的吸收率及电磁场分布,并研究了入射角及结构参数的变化对多峰值吸收的影响。考虑到磁激元的本质是由金属光栅下表面与金属基底上表面诱导出反向电流震荡引起,多层介质膜起到介电隔离层的作用。对多层介质膜进行等效介质理论近似,并通过等效LC电路预测和分析了基模磁激元谐振频点。本文所提出的多带吸收机理在红外探测、辐射制冷领等域具有应用前景。