Extraction and isolation of linear alkylbenzene sulfonates and their intermediate metabolites from various marine organisms

A method has been developed for the determination of linear alkylbenzene sulfonates and its degradation intermediates (sulfophenylcarboxylic acids) from different marine organisms, which includes the stages of extraction and analysis by liquid chromatography with fluorescence detection. The extraction stage (Soxhlet and solid-phase extractions) was optimised by the selection of the appropriate solvent, minicolumns and different clean-up stages. Recoveries varied in the range from 80 to 104%, with a standard deviation between 1 and 9%. Detection limits were 15 ng g(-1) wet mass for undecylbezene sulfonate and 30 ng g(-1) wet mass for sulfophenylundecanoic acid using HPLC-fluorescence detection. The complete analytical method was successfully applied to different marine organisms from the Bay of Cadiz (SW Spain).     

Determination of linear alkylbenzene sulfonates by ion-pair solid-phase extraction and high-performance liquid chromatography

In this paper, the potential use of multiwalled carbon nanotubes (MWCNTs) as solid phase extraction (SPE) adsorbent was evaluated for preconcentration of linear alkylbenzene sulfonates (LAS) using ion-pair (IP)-SPE with tetrabutylammonium hydroxide (TBAH). The LAS homologues present in the aqueous sample were ion-paired with TBAH and the solution was passed through the MWCNT cartridges. The analytes retained in the cartridge were eluted with methanol and the concentrated methanol extract was analysed by HPLC-UV. In order to obtain the satisfactory recovery of LAS homologues, various parameters including the type and amount of the ion-pair reagents, the desorption and enrichment conditions such as the effect of eluent and its volume, pH, the flow rate, the ultrasonic time of sample, and the volume of sample solution were systematically optimized. Under the optimal conditions, LAS homologues could be easily extracted by the proposed SPE cartridge. The favorable limits of detection (LOD) for LAS homologues were in the range from 0.02 to 0.03 μg L⁻¹, and the relative standard deviations (RSDs) were 1.55-2.54% for 10 μg L⁻¹ LAS (n = 6). The proposed method has been successfully applied for the analysis of LAS homologues in aqueous environmental samples. A comparison study with ion-pair solid extraction on MWCNTs, C8 and C18 as adsorbents for LAS demonstrated that ion pair-based solid extraction on MWCNTs adsorbent was advantageous over C8 and C18, the widely used traditional adsorbents.     

Screening method for linear alkylbenzene sulfonates in sediments based on water Soxhlet extraction assisted by focused microwaves with on-line preconcentration/derivatization/detection

A screening method for linear alkylbenzene sulfonates (LAS) in sediments has been developed. Soxhlet extraction with water assisted by focused microwaves provides recoveries better (>90%) than obtained by conventional Soxhlet extraction (70-80%). Coupling of the extractor with an on-line preconcentration/derivatization/detection manifold through a flow injection (FI) interface allows a fully automated screening approach. A yes/no answer can be obtained in less than 2 h (for the whole analytical process), a short time compared with the at least 24 h of Soxhlet extraction (without final detection). Due to the use of water as leaching agent, the proposed method is environmentally friendly.     

Evaluation of eggshell membrane-based bio-adsorbent for solid-phase extraction of linear alkylbenzene sulfonates coupled with high-performance liquid chromatography

The potential of eggshell membrane (ESM) as a novel solid-phase extraction bio-adsorbent was investigated in the present study. The ESM with a unique structure of intricate lattice network showed a predominant ability to capture linear alkylbenzene sulfonates (LAS) as a model of organic pollutants by the hydrophobic interactions between ESM and LAS molecular at pH very close to the isoelectric point of ESM, which was similar to the most widely used trapping mechanism for SPE. Under the optimal conditions, the breakthrough capacities of the ESM packed cartridge for C10–C13 LAS homologues were found to be 30, 53, 50, and 43 μg g⁻¹, respectively. On the basis of high-performance liquid chromatography separation and UV detection of LAS homologues, the proposed system could respond down to 0.027 ng mL⁻¹ of LAS with a linear calibration range from 0.2 to 100 ng mL⁻¹, showing a good LAS enrichment ability of eggshell membrane biomaterial with high sensitivity, and could be successfully used for the detection of residual LAS in environmental water samples. The reproducibility among columns was satisfactory (RSD among columns is less than 10%). A comparison study with ESM, C8 and C18 as adsorbents for LAS demonstrated that ESM-based bio-adsorbent was advantageous over C8 and C18, the widely used traditional adsorbents.     

Carboxyl modified multi-walled carbon nanotubes as solid-phase extraction adsorbents combined with high-performance liquid chromatography for analysis of linear alkylbenzene sulfonates

Recently, multi-wall carbon nanotubes (MWCNTs) as adsorbents of solid-phase extraction are attractive because they can be used for enrichment of organic compounds and metal ions at trace levels. In this study, we use the carboxyl modified multi-wall carbon nanotubes (CMMWCNTs) as adsorbents of solid-phase extraction for extraction of linear alkylbenzene sulfonates (LAS), which are widely used anion surfactant with different homologues, and detected by HPLC-UV. The effect of eluent and its volume, sample pH and flow rate, sample volume and the ultrasonic time of sample, the content of the electrolyte (NaCl) were investigated and optimized. The detection limit for LAS homologues was 0.02-0.03 μg L⁻¹ with R.S.D. (n = 6) ranging from 2.04 to 10.03%. The recoveries of LAS homologues in the spiked environmental water samples ranged from 84.8 to 106.1%. The proposed method has been applied successfully to the analysis of LAS in aqueous environmental samples, which demonstrates that CMMWCNTs-based solid-phase extraction is a precision and convenient enrichment method and can be used for analysis of LAS homologues in water samples.     

Bioconcentration of linear alkylbenzene sulfonates and their degradation intermediates in marine algae

Sorption experiments using different homologues of linear alkylbenzene sulfonate (LAS) and sulfophenylcarboxylic acid (SPC) on several marine microalgae have been carried out. The steady state seems to be reached in the first 4 hours. Longer exposure times lead to biodegradation of the compound and, therefore, to an overestimation of the bioconcentration factor. Sorption coefficients are higher for Nannochloropsis gaditana, for example, 1,293 Lkg(-1) for C11-LAS and 525 Lkg(-1) for C11-SPC versus 727 Lkg(-1) for C11-LAS and 28 Lkg(-1) for C11-SPC for Dunaliella salina. For both algae an increase in the sorption coefficient is observed when the polarity of the compound decreases (C5-SPC相似文献   

Handling of marine and estuarine samples for the determination of linear alkylbenzene sulfonates and sulfophenylcarboxylic acids

Due to the physicochemical properties of linear alkylbenzene sulfonates (LAS), an anionic surfactant, it is difficult to obtain representative samples from sampling sites. Further, the high biodegradability of these compounds makes it necessary to study their biodegradation intermediates, sulfophenylcarboxylic acids (SPC) that do not have a surfactant character and show a different behavior. A procedure for determining and quantifying LAS and SPC in different environmental matrices by Soxhlet and solid-phase extractions and high-performance liquid chromatography is presented. The recoveries varied in the range from 85 to 102% for the water samples, and from 75 to 105% for sediment samples, with a standard deviation of between 1 and 7, and 2 and 11, respectively. Detection limits obtained were in the range from 5 to 10 microg kg(-1) for sediment samples (10 g) and from 0.2 to 0.4 microg l(-1) for water samples (250 ml). The method was applied to the simultaneous determination of LAS (C10-C13) and SPC (C4-C13) homologues in water, sediment and interstitial water collected from different areas of Spain.     

Highly stable magnetic multiwalled carbon nanotube composites for solid-phase extraction of linear alkylbenzene sulfonates in environmental water samples prior to high-performance liquid chromatography analysis

The magnetic multiwalled carbon nanotubes (MMWCNTs) have been successfully prepared using a one-pot chemical coprecipitation method, in which magnetic nanoparticles (MNPs) were deposited onto multiwalled carbon nanotubes (MWCNTs) by in situ high temperature decomposition of the magnetic precursor of iron(III) in ethylene glycol media. A novel procedure for extraction of linear alkylbenzene sulfonates (LAS) as a model compound was thus developed in an off-line extraction system with detection by HPLC. The procedure includes the separation and preconcentration of LAS homologues onto MMWCNTs at pH 7.0 and their subsequent detection after sonication elution, followed by the separation of the MMWCNTs from the aqueous phase by external magnetic field and washing with ultra pure water. With a sample volume of 500 mL and 100 mg MMWCNTs sorbents, an enrichment factor of about 500, and a detection limit of 0.013-0.021 μg L(-1) were obtained within a linear range of 0.5-100 μg L(-1), together with a correlation coefficient of 0.9938-0.9998 for four LAS homologues. A precision of 2.4-5.6% was obtained for six replicate determinations of 50 μg L(-1) LAS. The recoveries of LAS homologues spiked in environmental water samples ranged from 87.3 to 106.3%, demonstrating the utility of the MMWCNTs adsorbents in a series of water samples. Stability testing demonstrated that the MMWCNTs remained 95.0% recovery for the target LAS even after a run of 50 adsorption and desorption cycles, showing their super operational stability. The MMWCNTs are promising adsorbents, suitable for the long-term repetitive sorption/desorption of target compounds in environmental water samples.     

Application of probe sonication extraction for the determination of linear alkylbenzene sulfonates from sewage sludge. Comparison with other extraction methods

A new method based on probe sonication extraction (USP) prior to high performance liquid chromatography (HPLC) has been developed for the determination of linear alkylbenzene sulfonates (LAS) from sewage sludge. The optimized method was designed to be cost effective compared to existing extraction methods (ultrasonic assisted extraction, Soxhlet or pressurized liquid extraction) which may require large quantities of organic solvents, or costly instrumentation or equipment.The main factors affecting the extraction efficiency (extractant volume, ultrasounds power and extraction time) were optimized using compost sludge. The detection limit of total LAS in the sludge was 10 mg kg^− 1. The extraction of C₁₀-C₁₃ homologues is carried out using an extraction time of 7 min with 10 mL of methanol. Liquid chromatography with fluorescence (FL) detector is used for determination of LAS homologues. A mobile phase acetonitrile-water containing 0.1 M NaClO₄ (65:35) and isocratic elution was used. Compounds were eluted over 6 min at a flow rate of 1 mL/min. Polar interferences are eluted between 0 and 2 min and no purification of the samples is required prior to the final determination by high performance liquid chromatography (HPLC). The recoveries of LAS in spiked sewage sludge were between 84.0% and 97.0%, which reflect the efficiency of the method for extraction of these analytes from sewage sludge. Concentration levels found were between 11,858 mg kg^− 1 for digested sludge and 2379 mg kg^− 1 for compost sludge.     

Pressurized liquid extraction in environmental analysis

A critical evaluation of recent literature utilizing pressurized liquid extraction (PLE) for environmental analysis is presented by compound class. Overall, the extraction efficiency of PLE, using the appropriate solvent, temperature and pressure for extraction, is similar to that of Soxhlet extraction. PLE has been used for some classes of compounds that are thermally labile (e.g., explosives) and may require acidic conditions for extraction (e.g., organometallic compounds). References to recent applications are presented emphasizing studies which utilize unspiked, natural matrices and studies that compare PLE to alternate extraction techniques.     

Determination of linear alkylbenzene sulfonates in water samples by liquid chromatography-UV detection and confirmation by liquid chromatography-mass spectrometry

A high-performance liquid chromatographic (HPLC) method was developed for the separation and determination of individual (C₁₀-C₁₃) linear alkylbenzene sulfonates (LAS). New sets of conditions have been established for routine analysis of individual chemical forms of four LAS surfactants, i.e. C₁₀-C₁₃ LAS. Under a condition set using a mobile phase containing 1.5 mM ammonium acetate in methanol/water 80:20 (v/v) mixture, detection limits obtained were in the range 1.5 ppb (for C₁₀ LAS) to 11.5 ppb (for C₁₃ LAS). This offers the advantages of significant improvement in resolution, short separation time and using less amount of common salt under isocratic condition. In addition, the use of simple mobile phase containing a simple low amount of salt cannot deposit at the entrance of mass spectrometric detector. The method is applicable to the simultaneous determination of LAS surfactants in various water samples. LAS surfactants presented in these samples were also successfully confirmed by using electrospray mass spectrometry.     

Determination of alkylphenols and linear alkylbenzene sulfonates in sediments applying accelerated solvent extraction (ASE)

A time and solvent saving method (accelerated solvent extraction, ASE) for the extraction of anionic surfactants as linear alkylbenzene sulfonates (LAS) and alkylphenols from sediments is presented. The analytes are extracted by methanol at 100 degrees C and 150 atm within 10 min of static and 5 min of dynamic extraction. The presence of methanol and a maximum pressure of 150 atm are essential for the complete extraction of anionic surfactants, whereas the extraction of alkylphenols is independent of both parameters. The extraction of alkylphenolethoxylates yielded only unsatisfactor results. It was demonstrated that the ASE extraction is selective for LAS surfactants, while matrix substances, which are extracted by the methanol extraction and interfere with the target analytes during the HPLC-run, remain in the sample. Thus, a further clean-up procedure of the ASE extract is not necessary.     

Determination of alkylphenols and linear alkylbenzene sulfonates in sediments applying accelerated solvent extraction (ASE)

A time and solvent saving method (accelerated solvent extraction, ASE) for the extraction of anionic surfactants as linear alkylbenzene sulfonates (LAS) and alkylphenols from sediments is presented. The analytes are extracted by methanol at 100° C and 150 atm within 10 min of static and 5 min of dynamic extraction. The presence of methanol and a maximum pressure of 150 atm are essential for the complete extraction of anionic surfactants, whereas the extraction of alkylphenols is independent of both parameters. The extraction of alkylphenolethoxylates yielded only unsatisfactor results. It was demonstrated that the ASE extraction is selective for LAS surfactants, while matrix substances, which are extracted by the methanol extraction and interfere with the target analytes during the HPLC-run, remain in the sample. Thus, a further clean-up procedure of the ASE extract is not necessary.     

Pressurized liquid extraction as a sample preparation method for the analysis of isoflavones in pulses

In this work, we describe a rapid and simple analytical method that exploits pressurized liquid extraction (PLE) and liquid chromatography with diode array detection for the determination of isoflavones in samples of Spanish pulses. Confirmation of the analytes present was performed using ion-trap mass spectrometry. To optimize the PLE extraction, variables such as the dispersing agent, type of solvent and sample amount, and the experimental parameters, such as temperature and the number of extraction cycles, were studied. Separation was carried out using a reverse-phase C18 with polar endcapping as the stationary phase and acetonitrile/water with 0.2?% of formic acid, under a gradient regime, as the mobile phase. Optimal extraction of formononetin and biochanin-A from chickpeas with PLE was achieved using Hydromatrix as a dispersant agent, methanol/water (50:50), a temperature of 90?°C, and three cycles. The same optimal conditions-except methanol/water (75:25)-for solvent extraction were obtained for the extraction of daidzin, genistin, and formononetin from lentils. Recoveries ranged from 97 to 110?%, and standard deviations lower than 20?% were obtained. The contents obtained for daidzin in lentils using the proposed method were not significantly different from those obtained using another official method of analysis.     

Microwave-assisted extraction versus Soxhlet extraction in the analysis of 21 organochlorine pesticides in plants

A method to determine 21 organochlorine pesticides in vegetation samples using microwave-assisted extraction (MAE) is described and compared with Soxhlet extraction. Samples were extracted with hexane–acetone (1:1, v/v) and the extracts were cleaned using solid-phase extraction with Florisil and alumine as adsorbents. Pesticides were eluted with hexane–ethyl acetate (80:20, v/v) and determined by gas chromatography and electron-capture detection. Recoveries obtained (75.5–132.7% for Soxhlet extraction and 81.5–108.4% for MAE) show that both methods are suitable for the determination of chlorinated pesticides in vegetation samples. The method using microwave energy was applied to grass samples from parks of A Coruña (N.W. Spain) and to vegetation from the contaminated industrial area of Torneiros (Pontevedra, N.W. Spain).     

Optimization of microwave-assisted extraction of hydrocarbons in marine sediments: comparison with the Soxhlet extraction method

Microwave energy was applied to extract polycyclic aromatic hydrocarbons (PAHs) and linear aliphatic hydrocarbons (LAHs) from marine sediments. The influence of experimental conditions, such as different extracting solvents and mixtures, microwave power, irradiation time and number of samples extracted per run has been tested using real marine sediment samples; volume of the solvent, sample quantity and matrix effects were also evaluated. The yield of extracted compounds obtained by microwave irradiation was compared with that obtained using the traditional Soxhlet extraction. The best results were achieved with a mixture of acetone and hexane ¶(1?:?1), and recoveries ranged from 92 to 106%. The extraction time is dependent on the irradiation power and the number of samples extracted per run, so when the irradiation power was set to 500 W, the extraction times varied from 6 min for 1 sample to 18 min for 8 samples. Analytical determinations were carried out by high-performance liquid chromatography (HPLC) with an ultraviolet-visible photodiode-array detector for PAHs and gas chromatography (GC) using a FID detector for LAHs. To test the accuracy of the microwave-assisted extraction (MAE) technique, optimized methodology was applied to the analysis of standard reference material (SRM 1941), obtaining acceptable results.     

Optimization of microwave-assisted extraction of hydrocarbons in marine sediments: comparison with the Soxhlet extraction method

Microwave energy was applied to extract polycyclic aromatic hydrocarbons (PAHs) and linear aliphatic hydrocarbons (LAHs) from marine sediments. The influence of experimental conditions, such as different extracting solvents and mixtures, microwave power, irradiation time and number of samples extracted per run has been tested using real marine sediment samples; volume of the solvent, sample quantity and matrix effects were also evaluated. The yield of extracted compounds obtained by microwave irradiation was compared with that obtained using the traditional Soxhlet extraction. The best results were achieved with a mixture of acetone and hexane (1:1), and recoveries ranged from 92 to 106%. The extraction time is dependent on the irradiation power and the number of samples extracted per run, so when the irradiation power was set to 500 W, the extraction times varied from 6 min for 1 sample to 18 min for 8 samples. Analytical determinations were carried out by high-performance liquid chromatography (HPLC) with an ultraviolet-visible photodiode-array detector for PAHs and gas chromatography (GC) using a FID detector for LAHs. To test the accuracy of the microwave-assisted extraction (MAE) technique, optimized methodology was applied to the analysis of standard reference material (SRM 1941), obtaining acceptable results.     

Application of liquid chromatography-electrospray-tandem mass spectrometry for the identification and characterisation of linear alkylbenzene sulfonates and sulfophenyl carboxylates in sludge-amended soils

A novel procedure was developed for the simultaneous determination of linear alkylbenzene sulfonates (LAS) and their major metabolites, sulfophenyl carboxylates (SPC), in sludge-amended soil. After pressurised liquid extraction with methanol/water (90:10) and a clean-up on C18 solid-phase extraction cartridges, final analysis was done by ion-pair liquid chromatography-electrospray-tandem mass spectrometry (LC-ESI-MS/MS). With this method, SPC with 5-13 carbon atoms in the aliphatic side chain were identified for the first time in agricultural soils treated with sewage sludge. Quantification of LAS and SPC in soil from 10 field sites, which differed in the history of sludge application, gave total concentrations of 120-2840 microg kg(-1) for LAS and of 4-220 microg kg(-1) for SPC. The data provided evidence for rapid biodegradation of LAS in the initial phase after sludge amendment with a transitory build-up of high concentrations of, mainly, short-chain SPC. Trace amounts of residual LAS and SPC were detected in soils having received the last sludge treatment 10 days to 4 years prior to sampling.     

The stability of non-ionic surfactants and linear alkylbenzene sulfonates in a water matrix and on solid-phase extraction cartridges

The stability of nonylphenol ethoxylates (NPEO), alcohol ethoxylates (AEO), coconut diethanol amides (CDEA) and linear alkylbenzene sulfonates (LAS) in a water matrix and preconcentrated on SPE cartridges was studied. A stability study was carried out in a water matrix (spiked ground water and real-world waste water) comparing different pretreatment procedures (addition of sulfuric acid to pH = 3, preservation with 1% and 3% of formaldehyde). When stored in a water matrix serious qualitative and quantitative changes occurred in waste water during the period of time studied (30 days). The losses of C12-C14 alcohol ethoxylates ranged from 72% to 88% when the sample was preserved with acid and from 17% to 86% when the sample was preserved with formaldehyde (3%). Simultaneously, an enrichment of the shorter alkyl chain homologues (C7EO and C10EO) was observed. The losses of NPEO were from 45% (sample preserved by acidification or by addition of 3% of formaldehyde) to 85% (sample preserved with 1% of formaldehyde). Additionally, an increase in concentration of polyethylene glycols (PEGs) and formation of different acidic forms, such as monocarboxylated (MCPEGs) and dicarboxylated polyethylene glycols (DCPEGs) were observed. The stability of surfactants preconcentrated on SPE cartridges was studied as a function of storage time and storage conditions (room temperature, 4 degrees C and -20 degrees C). The results indicate that disposable SPE cartridges can be recommended for the stabilization of non-ionic surfactants and LAS. Storage at -20 degrees C is feasible for long periods (up to 3 months for ground water and up to 2 months for waste water), while storage at 4 C can be recommended for a maximum of 1 month. When cartridges were kept at -20 degrees C the losses of AEOs (n = 12, 13 and 14), preconcentrated from waste water, ranged from 17 to 29% (after 60 days) and other compounds suffered small losses (maximum of 14% for C13LAS). At room temperature, after 7 days, the losses were less than 11%, indicating that shipping of samples by mail can be done without any special requirements.     

The stability of non-ionic surfactants and linear alkylbenzene sulfonates in a water matrix and on solid-phase extraction cartridges

The stability of nonylphenol ethoxylates (NPEO), alcohol ethoxylates (AEO), coconut diethanol amides (CDEA) and linear alkylbenzene sulfonates (LAS) in a water matrix and preconcentrated on SPE cartridges was studied. A stability study was carried out in a water matrix (spiked ground water and real-world waste water) comparing different pretreatment procedures (addition of sulfuric acid to pH = 3, preservation with 1% and 3% of formaldehyde). When stored in a water matrix serious qualitative and quantitative changes occurred in waste water during the period of time studied (30 days). The losses of C₁₂–C₁₄ alcohol ethoxylates ranged from 72% to 88% when the sample was preserved with acid and from 17% to 86% when the sample was preserved with formaldehyde (3%). Simultaneously, an enrichment of the shorter alkyl chain homologues (C₇EO and C₁₀EO) was observed. The losses of NPEO were from 45% (sample preserved by acidification or by addition of 3% of formaldehyde) to 85% (sample preserved with 1% of formaldehyde). Additionally, an increase in concentration of polyethylene glycols (PEGs) and formation of different acidic forms, such as monocarboxylated (MCPEGs) and dicarboxylated polyethylene glycols (DCPEGs) were observed. The stability of surfactants preconcentrated on SPE cartridges was studied as a function of storage time and storage conditions (room temperature, 4?°C and –20?°C). The results indicate that disposable SPE cartridges can be recommended for the stabilization of non-ionic surfactants and LAS. Storage at –20?°C is feasible for long periods (up to ¶3 months for ground water and up to 2 months for waste water), while storage at 4?°C can be recommended for a maximum of 1 month. When cartridges were kept at –20?°C the losses of AEOs (n = 12, 13 and 14), preconcentrated from waste water, ranged from 17 to 29% (after 60 days) and other compounds suffered small losses (maximum of 14% for C₁₃LAS). At room temperature, after 7 days, the losses were less than 11%, indicating that shipping of samples by mail can be done without any special requirements.