Structure and properties of the 70Li2S · (30 − x)P2S5 · xP2O5 oxysulfide glasses and glass–ceramics

The 70Li₂S · (30 ? x)P₂S₅ · xP₂O₅ (mol%) oxysulfide glasses were prepared by the melt quenching method. The glasses were prepared in the composition range 0 ≦ x ≦ 10. The glass–ceramics were prepared by heating the glasses over crystallization temperatures. The PO_nS_3?n (n = 1–3) oxysulfide units were produced in the glasses and glass–ceramics by partial substituting P₂O₅ for P₂S₅. In particular, the P₂OS₆^4? unit would be produced by substituting a small amount of P₂O₅ for P₂S₅. The oxygen atoms were incorporated into the Li₇P₃S₁₁ crystal structure because the diffraction peaks of the oxysulfide glass–ceramic shifted to the higher angle side. The glass–ceramic with 3 mol% of P₂O₅ exhibited the highest conductivity of 3.0 × 10^?3 S cm^?1 and the lowest activation energy for conduction of 16 kJ mol^?1. The P₂OS₆^4? dimer units in the oxygen-incorporated Li₇P₃S₁₁ crystal would improve conductive behavior of the Li₂S–P₂S₅ glass–ceramics.     

Bond character,optical properties and ionic conductivity of Li2O/B2O3/SiO2/Al2O3 glass: Effect of structural substitution of Li2O for LiCl

A glass of composition (20 ? x)Li₂O–xLiCl–65B₂O₃–10SiO₂–5Al₂O₃ where 0 ? x ? 12.5 wt% is prepared using the normal melt-quenching technique. The optical constants and electrical conductivity and their correlation are investigated, furnished and discussed with the substitution of Li₂O for LiCl. The mechanism of the optical absorption and the calculated Urbach energy follow the rule of phonon-assisted transitions. The ionic conduction mechanism is determined by activation energy process. Substitution up to 10 wt% LiCl provides high ionic conductivity (1.9 × 10^?2 Ω^?1 m^?1) due to the high average electronegativity of LiCl which increases the polarizability of lithium ions. The small cation–anion distance approach confirmed the enhancement in ionic conductivity of LiCl containing glass compared to that of Li₂O. Due to the large size of Cl^? ions, there is an expansion of the lattice which in turn broadens the available path windows. For 12.5 wt% LiCl, anomalous density behavior is observed and a reduction in conductivity is occurred, σ = 5.4 × 10^?3 Ω^?1 m^?1. Owing to the model of bond fluctuation, the reduction is attributed to the increase in the alkali halide concentration which creates bottlenecks that hinder the motion of Li⁺ ions. The ionic conductivity character is strongly supported by the behavior of the glass ionicity factor, density, molar volume, refractive index, average boron–boron separation, molar refraction, metallization criterion and non-bridging oxygen concentration of the studied glass.     

Ion transport studies in CuI-doped silver borovanadate glassy system

In the present report, ionic transport properties and microstructural investigations of superionic materials in a cost-effective glassy system xCuI–(100 ? x)[2Ag₂O–0.7V₂O₅–0.3B₂O₃], where x = 30, 40, 45, 50 and 60, have been described. The temperature dependent electrical conductivity studies were carried out by ac impedance analysis. The microstructure of the materials studied by SEM indicated the presence of dispersed CuO and AgI micro-crystals in the silver oxysalt glass matrix. High room temperature electrical conductivity of 3.58 × 10^?3 S cm^?1 and low activation energy of 0.24 eV were obtained for the best conducting composition. The ac impedance data were analyzed using impedance and modulus formalisms. These materials show extremely high t_i value of 0.999 and the ionic conductivity is apparently due to Ag⁺ ions only. The use of two glass formers helped to form materials with higher T_g, higher thermal stability and better ionic transport properties.     

Preparation of lithium ion conducting glasses and glass–ceramics for all-solid-state batteries

Highly lithium ion conducting glasses and glass–ceramics were prepared by a mechanical milling technique in the Li₂S-based sulfide and oxysulfide systems. The Li₂S–P₂S₅ glass–ceramics showed ionic conductivity as high as 3.2 × 10^?3 S cm^?1 at room temperature. All-solid-state batteries using these sulfide-based materials as a solid electrolyte showed excellent charge–discharge performance with high capacity and high cycleability. The cells with the combination of the SnS–P₂S₅ glassy electrode and the Li₂S–P₂S₅ glass–ceramic electrolyte worked as a secondary battery, which was a first step of glassy monolithic cells with a common glass network.     

Synthesis of two-dimensional metallic silver using sodium beta-alumina crystal channels

Sodium beta-alumina (β-NaAl₁₁0₁₇) crystals were grown within a gel containing Na₂O and Al₂O₃. The glass–crystal composite was put through a Na⁺ ? Ag⁺ ion-exchange reaction. The ion-exchanged glass–crystal was then subjected to an electrodeposition process. Nanosheets of metallic silver were found to have grown within the β-NaAl₁₁0₁₇ channels which usually contain the mobile sodium ions. The DC electrical resistance of the composites was caused due to charge transport in the two-dimensional crystal planes. The average silver layer thickness was ～0.6 nm and the interlayer separation ～1.13 nm.     

Performance investigation of Li2O–Al2O3–4SiO2 based glass–ceramics with B2O3, Na3AlF6 and Na2O fluxes

Influence of single fluxes (10 wt.% B₂O₃), bi-component fluxes (4 wt.% B₂O₃ + 6 wt.% Na₃AlF₆), and complex fluxes (4 wt.% B₂O₃ + 4 wt.% Na₃AlF₆ + 2 wt.% Na₂O) on the thermal kinetic parameters, microstructure, flexural strength and coefficient of thermal expansion (CTE) of Li₂O–Al₂O₃–4SiO₂ (LAS) glass–ceramics was investigated through differential thermal analysis (DTA), X-ray diffraction (XRD), and scanning electron microscope (SEM). The results showed that complex fluxes could efficiently decrease transition temperature (T_g) and crystallization temperature (T_p), and accelerate the formation of needle-like β-spodumene crystals which benefit high flexural strength. The homogeneous LAS glass–ceramic (sample C₃) which has a high strength of 132.4 MPa and low CTE (100–650 °C) of 2.74 × 10^? 6/°C is obtained by doping of the initial LAS glass by complex fluxes of 4 wt.% B₂O₃, 4 wt.% Na₃AlF₆, and 2 wt.% Na₂O, nucleating at 630 °C/120 min and then crystallized at 780 °C/120 min. It is worthy of further investigation as a bonder of diamond composite material due to its outstanding prosperities.     

Structure and properties of NaPO3–ZnO–Nb2O5–Al2O3 glasses

In an effort to design low-melting, durable, transparent glasses, two series of glasses have been prepared in the NaPO₃–ZnO–Nb₂O₅–Al₂O₃ system with ZnO/Nb₂O₅ ratio of 2 and 1. The addition of ZnO and Nb₂O₅ to the sodium aluminophosphate matrix yields a linear increase of properties such as glass transition temperature, density, refractive index and elastic moduli. The chemical durability is also significantly, but nonlinearly, improved. The glass with the highest niobium concentration, 55NaPO₃–20ZnO–20Nb₂O₅–5Al₂O₃ was found to have a dissolution rate of 4.5 × 10^? 8 g cm^? 2 min^? 1, comparable to window glass. Structural models of the glasses were developed using Raman spectroscopy and nuclear magnetic resonance spectroscopy, and the models were correlated with the compositional dependence of the properties.     

Structure of potassium germanophosphate glasses by X-ray and neutron diffraction: 3. Reverse Monte Carlo simulations

Reverse Monte Carlo (RMC) is used to investigate the origin of the first sharp diffraction peaks (FSDP) found for K₂O–GeO₂–P₂O₅ glasses at very small scattering vector Q = ～7.5 nm^?1. Structures of the ternary glass with the greatest intensity of FSDP (KGeP5 – 25/50/25 mol% K₂O/GeO₂/P₂O₅), of the binary combinations of the three oxides and of vitreous GeO₂ are modeled. Results are deduced from comparisons of the partial structure factors and inspections of model sections. The P sites are uniformly distributed in the structure of KGeP5. The K⁺ ions interact more with the PO₄ units (via O_T-corners) than with Ge-centered units. Main component of the FSDP comes from the S_GeGe(Q) factor. The FSDP is due to separations of ～1 nm between the longish Ge-rich clusters which are visible in the corresponding models. Different to our tentative structural models reported before, the PO₄ tetrahedra possess a broad distribution of numbers of O_T corners. The FSDP’s of the binary K₂O–GeO₂ and K₂O–P₂O₅ glasses (～10 nm^?1) are due to a chemical order between network former and network modifier regions. The MRO of a mixed GeO₂–P₂O₅ glass of small P₂O₅ content (FSDP at ～16 nm^?1) shows great similarity to the MRO of vitreous GeO₂.     

Er3+-doped germanate glasses for active waveguides prepared by Ag+/K+ ↔ Na+ ion-exchange

Planar waveguides were prepared by Ag⁺/K⁺ ? Na⁺ ion-exchange on Er⁺³-doped GeO₂–ZnO–Na₂O–Li₂O glasses obtained by a melting–casting method. Optical parameters of the waveguides were measured at 543.5, 632.8, and 1550 nm by m-line technique as a function of the Ag⁺ ion-exchange time. The optimized planar waveguides show an effective diffusion depth (d) of 2.95 μm and well confined propagating TE₀ and TM₀ modes at 1550 nm. Spectroscopic properties as photoluminescence emission and emission decay time were evaluated for the erbium-doped planar waveguide, indicating that Ag⁺ ? Na⁺ ion-exchange enhance the photoluminescence emissions in the green and infrared regions from erbium ions. The glass system studied is promising to be applied as optical amplifiers in the C-telecom band. Green emission sensitized by Ag⁺ was also observed.     

Effect of Li2O on the heterogeneous structure of equi-molar lead borate glasses

Different glass samples in the Li₂O, PbO and B₂O₃ system have been prepared by melt quenching method. These glasses were classified in two groups such as 0.5 B₂O₃, (0.5 ? x) PbO, xLi₂O and (0.5 + y) B₂O₃; (0.25 ? y)PbO; 0.25Li₂O. The IR spectra almost show broad bands in the frequency range (800–1050) cm^?1 and (1100–1500) cm^?1, together with different weak bands over the range of investigation (2400–3000) cm^?1. The deconvolution analyses of these IR spectra reveals presence of multi structure arrangements from BO₄ and BO₃ groups, such as penta, tri, and diborates grouping together with meta; ortho borates as well as PbO_n groups. Partial replacement of PbO by Li₂O causes decrease in microhardness, a change which is attributed to the decrease in the concentration of ortho borate groups as is it revealed from the bands area analysis. The IR analysis shows also that the total concentration of (meta + ortho) borates is nearly constant while their individual concentrations is proportional depending on the relative concentration of PbO and Li₂O.     

Formation of Co2+-doped nanocrystals in La2O3–MgO–Al2O3–SiO2 glass-ceramics

Transparent glass-ceramics were synthesized by heat-treatment of glass with a composition of 5La₂O₃–13.2MgO–28.8Al₂O₃–46SiO₂–4.5TiO₂–2.5ZrO₂–0.15CoO (LMAS) (wt.%). The activation energy of crystallization and the Avrami parameter for the LMAS glass were determined from the DTA curves at different heating rates. The most two intense bands of Raman spectrum of initial glass at ~ 810 cm^?1 and ~ 900 cm^?1 were connected with the presence of [SiO₄] and [TiO₄] tetrahedral, respectively. After heat-treated at 700 °C/10 h+820 °C/8 h, the intensity of the band for [TiO₄] tetrahedral weakened, while an intensive band at ~ 800 cm^?1 for the Ti–O bond appeared. Other bands were characteristics of high-silicate network and x(MgTi₂O₅)·y(Al₂TiO₅) polycrystals. The changes reflected phase separation after heat-treatment of the initial glass. The strong absorption band of glass-ceramics centered at 580 nm can be assigned to ⁴A₂(⁴F)→⁴T₁(⁴P) and the broad absorption band at 1100–1700 nm to ⁴A₂(⁴F)→⁴T₁(⁴F) transitions of tetrahedral coordinated Co²⁺ ion. Two broad emission bands, one was around 660 nm, the other was from 800 nm to 1050 nm, of glass-ceramics correspond to the ⁴T₁(⁴P)→⁴A₂(⁴F) and ⁴T₁(⁴P)→⁴T₂(⁴F) transitions of tetrahedral coordinated Co²⁺ ions. The absorption and emission features clearly demonstrated that Co²⁺ ions were incorporated into nanocrystals and located in tetrahedral sites.     

The preparation and structural studies in the (80 − x)TeO2–20ZnO–(x)Er2O3 glass system

Er³⁺-doped tellurite glasses of the (80 ? x)TeO₂–20ZnO–(x)Er₂O₃ system (0.5 mol% ? x ? 2.5 mol%) have successfully been made by melt-quenching technique and their structure has been investigated by means of DTA and Raman spectroscopy. The DTA results show the thermal parameters; such as the glass transition temperature (T_g) and crystallization temperature (T_c) were determined. It is found that this system provides a stable and wide glass formation range in which the glass stability around 99–140 °C may be obtained. The Raman spectroscopy used the structural studies in the glass system. Two Raman shift peaks were observed around 640–670 cm^?1 and 720–740 cm^?1, which correspond to the stretching vibration mode of TeO₄ tbp and TeO₃ tp, respectively. It is found that the spectral shift in Raman spectra is depending on the Er₂O₃ content. This evolution is an indication of the changes in the basic unit of the glass structure.     

Spectroscopic properties of Tm3+ doped TeO2-R2O-La2O3 glasses for 1.47 μm optical amplifiers

Upon excitation at 808 nm laser diode, an intense 1.47 μm infrared fluorescence has been observed with a broad full width at half maximum (FWHM) of about 124 nm for the Tm³⁺-doped TeO₂-K₂O-La₂O₃ glass. The Judd–Ofelt parameters found for this glass are: Ω₂ = 5.26 × 10^?20 cm², Ω₄ = 1.57 × 10^?20 cm² and Ω₆ = 1.44 × 10^?20 cm². The calculated emission cross-sections of the 1.47 μm transition are 3.57 × 10^?21 cm², respectively. It is noted that the gain bandwidth, σ_e × FWHM, of the glass is about 440 × 10^?28 cm³, which is significantly higher than that in ZBLAN and Gallate glasses, a high gain of 35.5 dB at 1470 nm can be obtained in a TKL glass fiber. TeO₂-R₂O (R = Li, Na, K)-La₂O₃ glasses has been considered to be more useful as a host for broadband optical fiber amplifier.     

Optical band gap and Raman spectra in some (Bi2O3)x(WO3)y(TeO2)100−x−y and (PbO)x(WO3)y(TeO2)100−x−y glasses

The glasses representing (Bi₂O₃)_x(WO₃)_y(TeO₂)_100?x?y and (PbO)_x(WO₃)_y(TeO₂)_100?x?y systems were prepared. The dilatometric glass-transition temperatures of examined glass samples were found in the region 383–434 °C, the coefficient of thermal expansion varied from 12 to 16 ppm/°C and the density ranged from 6.30₂ to 6.80₈ g/cm³. From the optical transmission measurements of thin glassy bulk samples prepared by a glass blowing, the optical gap values were found in the narrow region 3.21–3.36 eV. For the temperature interval 300–480 K, the values of the temperature coefficient of the optical band gap varied from 3.7 × 10^?4 to 5.24 × 10^?4 eV/K. It is suggested that Raman feature observed at around 350 cm^?1 can be assigned to an overlap of Raman bands attributed to WO₆ corner shared octahedra and to the following three atomic linkages: Bi–O–Te, Pb–O–Te and W–O–Te.     

Effect of iron oxide addition on structural properties of calcium silico phosphate glass/glass-ceramics

Glasses with nominal composition 34SiO₂–(45 ? x) CaO–16 P₂O₅–4.5 MgO–0.5 CaF₂–x Fe₂O₃ (where x = 5, 10, 15, 20 wt.%) have been synthesized by melt quench technique. These have been investigated for structural features by using Fourier transform infra-red (FTIR) spectroscopy and X-ray photoelectron spectroscopy (XPS). Results have shown an increase in fraction of non‐bridging oxygen in glasses with an increase in iron oxide content up to 15 wt.% and subsequently decreases with further increase in iron oxide content to 20 wt.%. These effects are originated by the incorporation of Fe₂O₃ into the silica network. Iron oxide behaves as a network modifier at low concentration and stabilizes the glass network at higher content. The glass-ceramics exhibit an increase in the formation of magnetite phase with an increase in iron oxide. The glass phase in the glass-ceramics matrix, controls the surface dissolution, which in turn decides the response of the material in-vitro. The glass-ceramics with 15 wt.% iron oxide has shown optimum response in simulated body fluid.     

Characterization of chitosan/PVA blended electrolyte doped with NH4I

The (chitosan–PVA)–NH₄I electrolytes have been prepared by the solution casting method. The prepared electrolytes are analyzed using Fourier transform infrared (FTIR) spectroscopy in order to determine the interaction between salt and the polymer blend hosts which can be deduced from the band shifting. From infrared spectra, shifts are observed at the amine, carboxamide, carbonyl and hydroxyl bands of chitosan and PVA. These shifts indicate that complexation has occurred. The crystallinity/amorphousness of the blended electrolytes has been examined by X-ray diffraction (XRD). XRD pattern shows that the crystallinity of chitosan–NH₄I electrolyte increases with PVA concentration. Impedance of the electrolytes has been measured using electrochemical impedance spectroscopy (EIS) over the frequency range from 50 Hz to 1 MHz. The highest conducting sample 55 wt.% (chitosan–PVA)–45 wt.% NH₄I has conductivity of 1.77 × 10^? 6 S cm^? 1. The chitosan:PVA ratio is 1:1. This is higher than the conductivity for the unblended electrolyte 55 wt.% chitosan–45 wt.% NH₄I which is 3.73 × 10^? 7 S cm^? 1. From ln τ versus 10³/T plot, the activation energy for relaxation process is 0.87 eV. This is different from activation energy for dc conductivity which is 0.38 eV. Ion conduction is by hopping.     

Quantitation of sulfate solubility in borosilicate glasses using Raman spectroscopy

Raman spectroscopy is used here as an innovative technique to investigate sulfate content in borosilicate glasses. Using Raman spectroscopy after having heated the material, the evolution of sulfate amounts can be followed as a function of temperature, time and chemical composition of the starting matrix. The accuracy of this technique was verified using electron probe micro analysis (EPMA), on two systems of glasses (SiO₂–B₂O₃–Na₂O (SBNa) and SiO₂–B₂O₃–BaO (SBBa)) in order to compare the effect of alkaline or alkaline-earth elements on sulfur speciation and incorporation. To quantitate sulfate content with Raman spectroscopy, the integrated intensity of the sulfate band at 990 cm^?1 was scaled to the sum of the integrated bands between 850 and 1250 cm^?1, bands that are assigned to Qⁿ silica units. Calibration curves were then determined for different samples. The determination of sulfate contents with Raman spectroscopy analysis is possible with an accuracy of approximately 0.1 wt% depending on the composition of the glass. It mainly allows us to follow sulfate removal during the elaboration process and to establish kinetic curves of sulfate release as a function of the viscosity of the borosilicate glass.     

Lithium rich phosphate glass: Crystallization kinetics,structural and conduction characteristics

Crystallization kinetic studies of Li⁺ ion conducting mol% 60Li₂O–40P₂O₅ glass indicate a 2-dimensional crystal growth mechanism as compared to the 3-dimensional growth mechanism for LiPO₃ glass (mol% 50Li₂O–50P₂O₅). Spectroscopic studies reveal that the structures of these two glass compositions differ considerably resulting in different mechanisms for crystal growth. Isothermal ionic conductivity studies further support 2-dimensional crystallization in mol% 60Li₂O–40P₂O₅ glass. Above the glass transition temperature the ionic conductivity deviates from the usual Arrhenian temperature dependence due to the additional effect of the movement of the phosphate polymeric chains in the glass network. The ionic conductivity of the glass ceramic corresponding to the mol% 60Li₂O–40P₂O₅ glass behaves in an Arrhenian fashion with an activation energy of 1.21 eV, much higher than that of 0.77 eV for the glass. Further, it is established using canonical scaling that the mechanism for ionic conduction is temperature independent.     

Improved method for preparation of anhydrous silica by microwave irradiation with spectroscopic characterization and toxicity assay

Amorphous anhydrous silica SiO_{2 (mw)} (99.99%) is successfully synthesized through microwave irradiation technique and time of reaction is reduced up to 1 h. The dehydration phase study of Si–water, Si–OH, Si–O–Si networking, elemental analysis and surface morphology was carried out by FTIR, FTNIR, SEM and EDAX spectroscopic techniques. The broad absorption stretching and bending of Si–OH and H₂O at 3695.38–2832.96 cm^? 1, 1638 cm^? 1 and 1191.20–1017.14 cm^? 1 completely disappeared and appearance of new bands at 946.93 and 797.63 cm^? 1 confirmed the amorphous anhydrous silica with Si–O–Si networking. The SEM images of SiO_{2 (mwc)} described the smooth and fine particle texture and confirmed 99.99% Si–O–Si networking of anhydrous silica. The 99.99% purity was verified by EDAX spectra which exhibited sharp signals only for oxygen and silicon. Toxicity against Monomorium minimum and Tribolium castaneum with 100% mortality and LT₅₀ 91 min and 7.5 h respectively is being reported. It can be used for long storage of grains in the future.     

Thermal and optical properties of TeO2–ZnO–BaO glasses

We report the results of a systematic study of the thermal and optical properties of a new family of tellurite glasses, TeO₂–ZnO–BaO (TZBa), as a function of the barium oxide mole fraction and compare them with those of TeO₂–ZnO–Na₂O (TZN). The characteristic temperatures of this new glass family (glass transition, T_g, crystallization, T_x, and melting, T_m) increase significantly with BaO content and the glasses are more thermally stable (greater ΔT = T_x ? T_g) than TZN glasses. Relative to these, Raman gain coefficient of the TZBa glasses also increases by approximately 40% as well as the Raman shift from ~ 680 cm^? 1 to ~ 770 cm^? 1. The latter shift is due to the modification of the glass with the creation of non-bridging oxygen ions in the glass network. Raman spectroscopy allows us to monitor the changes in the glass network resulting from the introduction of BaO.