Bismuth-activated luminescent materials for broadband optical amplifier in WDM system

New broadband near infrared luminescence covering the whole work windows (1260–1625 nm) of the current wavelength division multiplexing (WDM) system was found from bismuth-activated M₂O–Al₂O₃–SiO₂ (M = Li, Na) and Li₂O–Ta₂O₅–SiO₂ glasses at room temperature in the case of 808 nm-laser excitation. But the near infrared luminescence mechanism of the bismuth-activated glasses is not well understood up to now. The figure-of-merits of bandwidth and gain of the glasses are better than those of Er³⁺-doped silicate glasses and Ti³⁺ doped sapphire, implying they are the promising gain-medium candidates for the broadband amplifiers and the widely tunable laser sources.     

The role of modifier’s cation valence in structural properties of TeO2-based glasses

The compositional invariance of the Raman spectra of (1 ? x)TeO₂–xM_nO_m glasses (M = Ti, Nb) is analyzed and interpreted as evidence for the conservatism of a framework-type constitution inherent to such glasses. This is assigned to the chemical similarity of cations in the X–O–Y bridges (X, Y = Te⁴⁺, Ti⁴⁺, Nb⁵⁺) considered as the framework building blocks. It is concluded that the atoms of metals having valence IV and V can be placed into the category of such cations, to which certain of the atoms with valence III can be added.     

The study of Sm3+-doped low-phonon-energy chalcohalide glasses

The Sm³⁺-doped low-phonon-energy (LPE) Ge–Ga–Se–CsI glasses were studied. Upon excitation at 980 nm diode laser, intense 1.25 and 1.49 μm near-infrared fluorescence bands with broad full width at half maximum (FWHM) of 49 and 53 nm were observed, respectively. About 180–300 μs fluorescence lifetimes were obtained for the 1.49 μm emission. The thermal properties and structure of glasses were investigated by differential thermal analysis (DTA) and Raman spectra, respectively. Spectroscopic characteristics of the optical transitions have been calculated by using the Judd–Ofelt theory and evaluated for excited levels.     

Crystallinity of the mixed phase silicon thin films by Raman spectroscopy

Raman spectra of the mixed phase silicon films were studied for a sample with transition from amorphous to fully microcrystalline structure using four excitation wavelengths (325, 514.5, 632.8 and 785 nm). Factor analysis showed the presence of two and only two spectrally independent components in the spectra within the range from 250 to 750 cm^?1 for all four excitation wavelengths. The 785 nm excitation was found optimal for crystallinity evaluation and by comparison with surface crystallinity obtained by atomic force microscopy, we have estimated the ratio of integrated Raman cross-sections of microcrystalline and amorphous silicon at this wavelength as y = 0.88 ± 0.05.     

Quantitative Raman spectroscopy: Principles and application to potassium silicate glasses

A mathematical approach was developed to interpret Raman spectra of binary silicate glasses and melts without the necessity of external calibration, e.g., from NMR spectroscopy. The developed approach is based on Principal Component Analysis (PCA), linear combinations of partial Raman spectra and a linear optimization technique. In order to apply and to test this approach, we developed an experimental method to collect a large number of Raman spectra efficiently. We applied the quantification and the experimental approaches to investigate potassium silicate glasses with compositions from 17.4 to 38 mol% K₂O. The equilibrium constant for the reaction 2Q³ ⇄ Q² + Q⁴ was found log K₃ = −2.37 ± 0.07, in excellent agreement with NMR studies for the same glasses.     

Cl effects on structure of Zr and Ti alkali aluminosilicate glasses

Na-aluminosilicate glasses with Na/Al > 1 and added Ti or Zr have been analyzed by Raman spectroscopy to determine the effect of Cl on glass structure. Spectra of Ti-bearing glasses show a significant difference between the Cl-free and the Cl-bearing composition. The Cl-free glass spectrum contains a strong, asymmetric peak at 900 cm⁻¹ which is associated with Ti in fivefold coordination. This peak is shifted to higher frequency and becomes more symmetric with the addition of 0.3 wt% Cl. Deconvolution of the high-frequency waveband indicates differences between spectra are the result of a contribution from a peak at 945 cm⁻¹ resulting from Ti–O vibrations in fully polymerized titanate tetrahedra. It is proposed that addition of Cl destabilizes ^[5]Ti in favor of tetrahedral coordination as a result of competition between Cl and titanate groups for alkalis. The spectra of Zr-bearing glasses show a strong peak at 980 cm⁻¹ which is not seen in spectra of the base glass, indicating a vibrational mode associated with a zirconosilicate structure. There is no discernible difference between the Raman spectra of Zr-bearing glasses with and without added Cl, indicating that the local structure around Zr is insensitive to the presence of Cl.     

Ultraviolet to near-infrared spectral modification in Ce3+ and Yb3+ codoped phosphate glasses

The ultraviolet to near-infrared spectral modification in Ce³⁺ and Yb³⁺ codoped phosphate glasses was realized through the energy transfer from Ce³⁺ to Yb³⁺. The absorption spectra, fluorescence excitation and emission spectra, luminescence decay curves, and time-resolved emission spectra were measured and analyzed. The energy transfer efficiency and concentration quenching efficiency were calculated based on the decay curves of Ce³⁺ 340 nm emission and Yb³⁺ 976 nm emission. The calculated and experimental NIR emission intensities on the Yb³⁺ concentrations were compared and discussed.     

Study of the effects of Ga3+ co-doping on the Lu0.8Sc0.2BO3:Ce scintillation crystals

Transparent Lu_0.8Sc_0.2BO₃ crystals doped with 1 at%Ce³⁺ and co-doped with 1 at% and 3 at%Ga³⁺ were grown by the Czochralski method. We applied absorption spectrum, luminescence spectra under UV and X-ray excitation, fluorescence decay curve, three dimensional thermoluminescene and X-ray absorption near edge spectroscopy to study the effect of Ga³⁺ co-doping on the Lu_0.8Sc_0.2BO₃:Ce scintillation crystals. Experimental results indicated that no positive contribution of the Ga³⁺ ion doping on the scintillation efficiency was found. The causes for the deterioration of scintillation efficiency by co-doping Ga³⁺ were revealed. The decrease of practical cerium content and the Ce³⁺/Ce⁴⁺ ratio in crystals, and the increase of the trap concentrations, although the corresponding trap types still maintained the same, played a joint influence on the degrading of scintillation efficiency of Lu_0.8Sc_0.2BO₃:Ce crystals.     

Microstructural analysis of Ga2S3–2MCl (M = K, Rb, Cs) glasses using Raman scattering

Raman scattering spectra of Ga₂S₃–2MCl (M = K, Rb, Cs) glasses have been conducted at room temperature. Based on the analysis of the local co-ordination surroundings of Cs⁺ ions, the similarities and differences of Raman spectra for the glass Ga₂S₃–2CsCl and the bridged molecular GaCl₃ were explained successfully. Through considering the effect of M⁺ ions on mixed anion units [GaS_4?xCl_x] and bridged units [Ga₂S_6?xCl_x] and the corresponding microstructural model, the Raman spectral evolution of the Ga₂S₃–2MCl (M = K, Rb, Cs) glasses was reasonably elucidated.     

Electrooptical Kerr phenomenon and Raman spectroscopy of one lithium–niobium–silicate glass-forming system

Raman spectra and electrooptical Kerr coefficients of glasses belonging to one lithium–niobate–silicate glass-forming system xNb₂O₅ · (66 ? x)SiO₂ · 19Li₂O · 11K₂O · 2B₂O₃ · 2CdO are studied. It has been found that these glasses demonstrate a record value of electrooptical Kerr coefficient; the glass with x = 35 showed electrooptical Kerr coefficient equal to 266 × 10^?16 m/V². Using Raman spectroscopy combined with the concept of Constant Stoichiometric Groupings, a correlation of electrooptical Kerr coefficients of these glasses with the content of Li₂O · Nb₂O₅ (or 2LiNbO₃) groupings has been demonstrated. The hypothesis that electrooptical Kerr sensitivity of glasses is related to the ordered regions with composition and symmetry corresponding to some of known electrooptical crystals has been verified. These regions, which the authors called ‘Crystal Motifs’, are identified with the groupings found in studying Raman spectra of the glasses.     

Glass formation in and structural investigation of Li2S + GeS2 + GeO2 composition using Raman and IR spectroscopy

Li₂S + GeS₂ + GeO₂ ternary glasses have been prepared and a wide glass-forming range was obtained. The glass transition temperatures increase with the GeO₂ concentration in the glasses. The vibrational modes of both bridging (Ge–S–Ge) and non-bridging (Ge–S⁻) sulfurs are observed in Raman and IR spectra of binary Li₂S + GeS₂ glasses. Additions of GeO₂ to this binary glass increase the bridging oxygen band (Ge–O–Ge) at the expense of decreasing the bridging sulfur band (Ge–S–Ge), whereas the bands associated with the non-bridging sulfurs (Ge–S⁻) remain constant in intensity up to high GeO₂ concentrations. At higher concentrations of GeO₂ (⩾60%), the non-bridging oxygen band, which is not observed at low and intermediate GeO₂ concentrations, appears and grows stronger. From these observations, it is suggested that the added lithium ions favor the non-bridging sulfur sites over the oxygen sites to form non-bridging sulfurs, whereas the added oxygen prefers the higher field strength Ge⁴⁺ cation to form bridging Ge–O–Ge bonds. The structural groups in the Li₂S + GeS₂ + GeO₂ glasses that are consistent with results of Raman and IR spectra are described and are used to develop a structural model of these glasses.     

Study of the alkaline environment in mixed alkali compositions by multiple-quantum magic angle nuclear magnetic resonance (MQ–MAS NMR)

45S5 Bioglasses of the composition 46.1 SiO₂–2.6 P₂O₅–26.9 CaO–(24.4 ? x) Na₂O–xMe₂O (Me = Li or K) have been investigated using MAS NMR and MQ–MAS NMR methods. The analysis of the ²⁹Si MAS NMR spectrum revealed two lineshapes whose chemical shift is consistent with two silica Q_n=2,3 species. The ³¹P MAS NMR spectrum reveals the effect of both Na and Ca ions. The chemical shift of the observed ³¹P signal is intermediate between those of Na₃PO₄ (near 10 ppm) and Ca₃(PO₄)₂ (near 3–0 ppm) species. The ²³Na MAS NMR spectra were observed in the alkali oxide composition: 24.4 Na₂O, 12.2 Na₂O–12.2 K₂O and 12.2 Na₂O–12.2 Li₂O. The substitution of Na with Li or K was done to determine the extend of alteration of the glass structure. This goal was best accomplished by ²³Na MQ–MAS NMR. The two-dimensional spectra revealed three sites in the 24.4 mol% Na₂O glass. These sites were not resolved in the 1D MAS NMR spectroscopy. In the mixed glasses, only two sites were obtained.     

Vibrational spectroscopy study of niobium germanosilicate glasses

A series of glasses in the (Ge,Si)O₂–Nb₂O₅–(Na,K)₂O system were prepared by melting and casting. Their density and characteristic temperatures were determined by Differential Thermal Analysis (DTA) and their structure was analyzed by infrared and polarized Raman spectroscopies. DTA data have indicated an increased glass thermal stability with the replacement of GeO₂ by SiO₂. Kramers–Kronig analysis of the infrared specular reflectance data indicated a strong ionic character for the germanosilicate glasses. The Raman spectra of germanosilicate compositions were generally dominated by an intense Boson peak at ∼72 cm⁻¹ and a high frequency, polarised peak at ∼880 cm⁻¹, related to NbO₆ octahedra with at least one non-bridging oxygen. The germanosilicate structure appears to be formed by alternating GeO₄ tetrahedra and NbO₆ octahedra, in addition to SiO₄ tetrahedra.     

IR absorption spectra of lithium and silver vanadium–tellurite based glasses

The aim of the present paper is to give structural information in order to set a correlation between the electrical conductivity behavior and structures of lithium and silver vanadium–tellurite based glasses. We report our structural studies and compare the effect of the nature of the metallic cation on glasses of the form XM₂O · (1 − X)V₂O₅ · 2TeO₂ (where 0 ⩽ X < 1 and M = Li or Ag). Fourier transform infra-red (FTIR) spectra were recorded for all compositions and complementary differential scanning calorimetry (DSC) measurements and X-ray diffraction (XRD) measurements were also carried out. This paper should be considered as complementary to a previous article reporting the conductive behavior of theses glasses. In the latter we reported the obtained results on electrical conductivity studies. The results confirm the existence of a transition from a typically electronic (polaronic) conductive regimen when the molar fraction (X) of M₂O is equal to 0, to an ionic conductive regimen when X tends to 1. The evidence for the independent migration path for both electrons and ions was put into evidence by studying the electrical conductivity behavior in a complementary system of the form X M₂O · (1 − X)[0.5V₂O₅–0.5MoO₃] · 2TeO₂. In this system vanadium was partially replaced by molybdenum which acts as a ‘diluting’ agent of the active centers involved in the electronic transport.     

Optical properties of Er3+-doped alkali fluorophosphate glasses

A systematic study of the optical absorption and luminescence spectra of Er³⁺-doped alkali fluorophosphate glasses (RTFP) 50(NaPO₃)–10TeO₂–20AlF₃–19RF–1Er₂O₃ (R = Li, Na and K) has been performed. The phenomenological Judd–Ofelt intensity parameters have been determined from the spectral intensities of the absorption bands in order to calculate the radiative transition probabilities, radiative lifetimes and branching ratios for various excited luminescent states. Using the visible and near infrared emission spectra, full width at half maximum (FWHM), emission cross-sections (σ_e) and figure of merit (FOM) were evaluated and compared with other hosts. Especially, the numerical values of these parameters indicate that the emission transition ⁴I_13/2 → ⁴I_15/2 transition at 1.534 μm in Er³⁺-doped fluorophosphate glasses may be highly useful in optical communication. The decay characteristic of ⁴S_3/2 excited level has also been recorded and analyzed. The calculated and experimental lifetimes were compared in terms of quantum efficiencies and multiphonon relaxation rates.     

Low-frequency Raman scattering and small-angle X-ray scattering of glasses inclined to phase decomposition

Low-frequency (<1000 cm⁻¹) Raman scattering of lithium aluminosilicate (12Li₂O : 15Al₂O₃ : 73SiO₂ with 4 mol% TiO2) glasses with addition of titanium dioxide has been studied. With a heat treatment at temperatures 660°C, 700°C, 720°C and 820°C and for various times and sequences of temperature, our samples decompose into nanometer sized dispersed aluminotitanate particles. In Raman spectra of these glasses an evolution of a boson peak was observed. The width of the relatively broad boson band decreases as does the frequency of the band. From small-angle X-ray scattering data we conclude that the boson peak is connected with elastic vibrations of amorphous or crystalline regions of inhomogeneity with a dimension of ∼1.7 nm in initial glasses or larger depending on the heat treatment sequences.     

Structure and properties of MoO3-containing zinc borophosphate glasses

ZnO–B₂O₃–P₂O₅ glasses doped with MoO₃ were investigated in the series (100?x)[0.5ZnO–0.1B₂O₃–0.4P₂O₅]–xMoO₃, where bulk glasses were obtained by slow cooling in air within the compositional region of 0 ? x ? 60 mol% MoO₃. The incorporation of MoO₃ into the parent zinc borophosphate glass results in a weakening of bond strength in the structural network, which induces a decrease in chemical durability and glass transition temperature. Raman spectra reflect the incorporation of molybdate groups into the glass network of the studied glasses by the presence of the polarized vibrational band at ≈976 cm^?1 ascribed to the MO_x symmetric stretching vibrations and the depolarized band at ≈878 cm^?1 ascribed to the Mo–O–Mo stretching vibration. The incorporation of molybdate units into the glass network results in the depolymerization of phosphate chains and the formation of P–O–Mo bonds, as reflected in Raman and ³¹P NMR spectra. According to the ¹¹B MAS NMR spectra, tetrahedral B(OP)_4?x(OMo)_x units are formed in the glasses, whereas only a small amount of BO₄ units is converted to BO₃ units in the MoO₃-rich glasses.     

Quantitation of sulfate solubility in borosilicate glasses using Raman spectroscopy

Raman spectroscopy is used here as an innovative technique to investigate sulfate content in borosilicate glasses. Using Raman spectroscopy after having heated the material, the evolution of sulfate amounts can be followed as a function of temperature, time and chemical composition of the starting matrix. The accuracy of this technique was verified using electron probe micro analysis (EPMA), on two systems of glasses (SiO₂–B₂O₃–Na₂O (SBNa) and SiO₂–B₂O₃–BaO (SBBa)) in order to compare the effect of alkaline or alkaline-earth elements on sulfur speciation and incorporation. To quantitate sulfate content with Raman spectroscopy, the integrated intensity of the sulfate band at 990 cm^?1 was scaled to the sum of the integrated bands between 850 and 1250 cm^?1, bands that are assigned to Qⁿ silica units. Calibration curves were then determined for different samples. The determination of sulfate contents with Raman spectroscopy analysis is possible with an accuracy of approximately 0.1 wt% depending on the composition of the glass. It mainly allows us to follow sulfate removal during the elaboration process and to establish kinetic curves of sulfate release as a function of the viscosity of the borosilicate glass.     

The structure of densified As2O3 glasses

In situ high energy X-ray diffraction and Raman experiments have been carried out to probe the structure changes of vitreous As₂O₃ under pressure. The first sharp diffraction peak reduces in intensity up to 10 GPa, indicating a breakdown of intermediate range order with pressure. All features in the Raman spectra broaden with increasing pressure up to 11.6 GPa. The mode at 378 cm⁻¹ associated with As₄O₆ molecule-like vibrations increases in intensity up to 6.2 GPa and decreases at higher pressures. In addition, X-ray and neutron structure factors have been measured for normal density and permanently densified As₂O₃ glasses recovered from 10 and 23 GPa. The results show the local AsO₃ pyramids and 3-membered rings essentially remain intact after compression. The increase in density is mainly associated with an inward shift of the third nearest neighbor peak in the X-ray radial distribution function, which indicates an increased packing of 3-membered AsO₃ rings.     

Structural studies of lead aluminate glasses

Lead aluminate melts were quenched rapidly with a roller quencher and bulk glasses were formed over a composition range from 72.5 to 80.0 mol% PbO. Pulsed neutron diffraction, ²⁷Al MAS NMR and Raman spectroscopy were used to study the structure of a series of these glasses. The results show that in the glasses the aluminium is four coordinated by oxygen across the compositional range, with a bond length of about 1.76 Å. The Pb–O peak in the neutron correlation function is asymmetric, and it can be modelled in terms of two bond lengths of ∼2.25 Å and ∼2.47 Å, with the majority of the coordination at the shorter distance. There is evidence that most or all of the lead ions are on asymmetric sites, coordinated by three oxygens in a trigonal pyramid arrangement. Both the neutron diffraction and Raman results indicate that the Pb–O bond lengths become shorter with increasing lead content.