Effect of annealing temperature on the optical and electrical properties of aluminum doped ZnO films

Aluminum doped ZnO thin films were successfully deposited on the silicon substrates by spin coating method. The effects of an annealing temperature on electrical and optical properties were investigated for 1.5 at.% of aluminum. Refractive index profile has been obtained for the film annealed at 350 °C using ellipsometry and it has shown minimum refractive index of 1.95 and maximum value of 2.1. Thickness profile shows quite good uniformity of the film having minimum thickness value of 30.1 nm and maximum value of 34.5 nm. Maximum conductivity value obtained was 4.63 Ω^?1-cm^?1 for the film annealed at 350 °C. Maximum carrier density of 2.20 × 10¹⁷ cm^?3 was deduced from the Hall measurement and Fourier transform infrared spectroscopy clearly reveals major peak at 407 cm^?1 in the spectra associated with the ZnO bond.     

Thermal annealing of a-Si/Au superlattice thin films

The superlattice films, which consist of amorphous silicon (a-Si) and amorphous gold (Au), were prepared by ultra-high vacuum evaporation system. The first layer was grown a-Si with a thickness of 4.2 nm and the second layer was grown Au with a thickness of 0.8 nm. Thermal annealing was performed at 473, 673, and 873 K, respectively. The structural properties of the films were investigated using transmission electron microscope (TEM), X-ray diffraction (XRD), and Raman scattering spectroscopy. The electrical property was assessed by the temperature dependence of electrical conductivity. A crystallization of Si and a forming of Au nanoparticles were observed in all of the annealing films. The crystalline volume fraction reached 70% by annealing time for 15 min. An average diameter of the Au nanoparticles embedded in Si matrix also increased with increasing the annealing temperature. At annealing temperature above 873 K, Au atoms migrated toward the film surface. It was observed that the electrical conductivity changed in several temperatures.     

Influence of precursor concentration on structural,morphological and electrical properties of spray deposited ZnO thin films

Nanostructured ZnO thin films were coated on glass substrate by spray pyrolysis using Zinc acetate dihydrate as precursor. Effect of precursor concentration on structural, morphological, optical and electrical properties of the films was investigated. The crystal structure and orientation of the ZnO thin films prepared with four different precursor solution concentrations were studied and it was observed that, the prepared films are polycrystalline in nature with hexagonal wurzite structure. The peaks are indexed to (100), (002), (101), (102) and (110) planes. Grain size and texture coefficient (TC) were calculated and the grain size found to increase with an increase in precursor concentration. Presence of Zn and O elements was confirmed with EDAX spectra. Optical absorption measurements were carried out in the wavelength region of 380 to 800 nm and the band gap decreases as precursor concentration increases. The current‐voltage characteristics were observed at room temperature and in dark. It was found that for the films deposited at four different precursor concentrations, the conductivity improves as precursor concentration increases. As trimethyl amine TMA is a good marker for food quality discrimination, sensing behavior of the films at an optimized operating temperature of 373 K, towards various concentrations of (TMA) was observed and reported. (© 2011 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Low temperature effects on electrical and optical properties of TTBNc thin films

Electrical and optical properties of thermally evaporated air annealed Tetra-Tert-Butyl 2,3 Naphthalocyanine (TTBNc) thin films are studied. From the Arrhenius plot, the thermal activation energy is calculated for intrinsic and extrinsic region. Different hopping conduction parameters are tabulated using the Variable Range Hopping (VRH) model in the low temperature region. The studies on the optical absorption spectra lead to the determination of optical band gap energy and Urbach’s energy of TTBNc thin films. Also the temperature dependence of steepness parameter is explained.     

Effect of annealing on the structural,electrical and optical properties of nanostructured TiO2 thin films

Nanostructured titanium dioxide thin films were prepared using reactive pulsed laser ablation technique. Effects of annealing on the structural, morphological, electrical and optical properties are discussed. The structural, electrical and optical properties of TiO₂ films are found to be sensitive to annealing temperature and are described with GIXRD, SEM, AFM, UV‐Visible spectroscopy and electrical studies. X‐ray diffraction studies showed that the as‐deposited films were amorphous and at first changed to anatase and then to rutile phase with increase of annealing temperature. Optical constants of these films were derived from the transmission spectra and the refractive index dispersion of the films, subjected to annealing at different temperatures, is discussed in terms of the single oscillator‐Wemple and Didomenico model. (© 2009 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Conductivity and temperature coefficient of resistance of multilayered polycrystalline films

We calculate the electric conductivity and the temperature coefficient of resistance (TCR) of a multilayered film consisting of the alternating polycrystalline metal layers of different thickness and purity within the relaxation time formalism. In the case of Cr, Cu and Co‐based multilayered films we perform verification of our analytical formulas and demonstrate a qualitative agreement between the theoretically calculated values of the TCR and experiment. (© 2006 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Influence of substrate temperature on the properties of vacuum evaporated InSb films

Indium Antimonide (InSb) thin films were grown onto well cleaned glass substrates at different substrate temperatures (303, 373 and 473 K) by vacuum evaporation. The elemental composition of the deposited InSb film was found to be 52.9% (In) and 47.1% (Sb). X‐ray diffraction studies confirm the polycrystallinity of the films and the films show preferential orientation along the (111) plane. The particle size (D), dislocation density (δ) and strain (ε) were evaluated. The particle size increases with the increase of substrate temperature, which was found to be in the range from 22.36 to 32.59 nm. In Laser Raman study, the presence of longitudinal mode (LO) confirms that the deposited films were having the crystalline nature. Raman peak located at 191.26 cm^–1 shift towards the lower frequencies and narrows with increase in deposition temperature. This indicates that the crystallinity is improved in the films deposited at higher substrate temperatures. Hall measurements indicate that the films were p‐type, having carrier concentration ≅10¹⁶ cm^–3 and mobility (4–7.7) ×10³ cm²/Vs. It is observed that the carrier concentration (N) decreases and the Hall mobility (μ) increases with the increase of substrate temperature. (© 2005 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Influence of oxygen/argon ratio on structural,electrical and optical properties of Ag-doped ZnO thin films

Ag-doped ZnO (ZnO:Ag) thin films were deposited on quartz substrates by radio frequency magnetron sputtering technique. The influence of oxygen/argon ratio on structural, electrical and optical properties of ZnO:Ag films has been investigated. ZnO:Ag films gradually transform from n-type into p-type conductivity with increasing oxygen/argon ratio. X-ray photoelectron spectroscopy measurement indicates that Ag substitutes Zn site (Ag_Zn) in the ZnO:Ag films, acting as acceptor, and being responsible for the formation of p-type conductivity. The presence of p-type ZnO:Ag under O-rich condition is attributed to the depression of the donor defects and low formation energy of Ag_Zn acceptor. The I–V curve of the p-ZnO:Ag/n-ZnO homojunction shows a rectification characteristic with a turn-on voltage of ∼7 V.     

Influence of annealing on the physical properties of filtered vacuum arc deposited tin oxide thin films

Tin oxide (SnO₂) thin films were deposited on UV fused silica (UVFS) substrates using filtered vacuum arc deposition (FVAD). During deposition, the substrates were at room temperature (RT). As-deposited films were annealed at 400 and 600 °C in Ar for 30 min. The film structure, composition, and surface morphology were determined as function of the annealing temperature using X-ray diffraction (XRD), atomic force microscopy (AFM), and X-ray photoelectron spectroscopy (XPS). The XRD patterns of the SnO₂ thin films deposited on substrates at RT indicated that the films were amorphous, however, after the annealing the film structure became polycrystalline. The grain size of the annealed films, obtained from the XRD analysis, increased with the annealing temperature, and it was in the range 8-34 nm. The AFM analysis of the surface revealed an increase in the film surface average grain size from 15 nm to 46 nm, and the surface roughness from 0.2 to 1.8 nm, as function of the annealing temperature. The average optical transmission of the films in the visible spectrum was >80%, and increased by the annealing ∼10%. The films’ optical constants in the 250-989 nm wavelength range were determined by variable angle spectroscopic ellipsometry (VASE). The refractive indexes of as-deposited and annealed films were in the range 1.83-2.23 and 1.85-2.3, respectively. The extinction coefficients, k(λ), of as-deposited and annealed films were in the range same range ∼0-0.5. The optical energy band gap (E_g), as determined by the dependence of the absorption coefficient on the photon energy at short wavelengths, increased with the annealing temperature from 3.90 to 4.35 eV. The lowest electrical resistivity of the as-deposited tin oxide films was 7.8 × 10⁻³ Ω cm, however, film annealing resulted in highly resistive films.     

Influence of substrate temperature on the properties of electron beam evaporated ZnSe films

ZnSe films were deposited on glass substrates keeping the substrate temperatures, at room temperature (RT), 75, 150 and 250 °C. The films have exhibited cubic structure oriented along the (111) direction. Both the crystallinity and the grain size increased with increasing deposition temperature. A very high value of absorption co‐efficient (10⁴ cm^‐1) is observed. The band gap values decrease from a value of 2.94 eV to 2.69 eV with increasing substrate temperature. The average refractive index value is in the range of 2.39 – 2.41 for the films deposited at different substrate temperatures. The conductivity values increases continuously with temperature. Laser Raman spectra showed peaks at 140.8 cm^‐1, 246.7 cm^‐1and 204.5 cm^‐1which are attributable to 2TA LO phonon and TO phonon respectively. (© 2010 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Influence of the substrate temperature on the structural,optical, and electrical properties of tin selenide thin films deposited by thermal evaporation method

Thin films of tin selenide (SnSe) were deposited on sodalime glass substrates, which were held at different temperatures in the range of 350‐550 K, from the pulverized compound material using thermal evaporation method. The effect of substrate temperature (T_s) on the structural, morphological, optical, and electrical properties of the films were investigated using x‐ray diffraction analysis (XRD), scanning electron microscopy (SEM), transmission measurements, and Hall‐effect characterization techniques. The temperature dependence of the resistance of the films was also studied in the temperature range of 80‐330 K. The XRD spectra and the SEM image analyses suggest that the polycrystalline thin films having uniform distribution of grains along the (111) diffraction plane was obtained at all T_s. With the increase of T_s the intensity of the diffraction peaks increased and well‐resolved peaks at 550 K, substrate temperature, were obtained. The analysis of the data of the optical transmission spectra suggests that the films had energy band gap in the range of 1.38‐1.18 eV. Hall‐effect measurements revealed the resistivity of films in the range 112‐20 Ω cm for films deposited at different T_s. The activation energy for films deposited at different T_s was in the range of 0.14 eV‐0.28 eV as derived from the analysis of the data of low‐temperature resistivity measurements. (© 2010 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Effect of annealing temperature on the structural and optical properties of amorphous Sb2Te2Se thin films

Thin films of Sb₂Te₂Se were prepared by conventional thermal evaporation of the presynthesized material on Corning glass substrates. The chemical composition of the samples was determined by means of energy‐dispersive X‐ray spectrometry. X‐ray diffraction studies on the as‐deposited and annealed films revealed an amorphous‐to‐crystalline phase transition. The as‐deposited and annealed films at T _a = 323 and 373 K are amorphous, while those annealed at T _a= 423 and 473 K are crystalline with a single‐phase of a rhombohedral crystalline structure as that of the source material. The unit‐cell lattice parameters were determined and compared with the reported data. The optical constants (n , k ) of the investigated films were determined from the transmittance and reflectance data at normal incidence in the spectral range 400–2500 nm. The analysis of the absorption spectra revealed non‐direct energy gaps, characterizing the amorphous films, while the crystalline films exhibited direct energy gaps. (© 2005 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Influence of impurities,irradiation and temperature on the mechanical and electrical properties of LiF crystals

On the basis of study of the temperature dependence of mechanical and electrical properties of LiF crystals with different impurities an evident interaction between radiation defects and impurities is revealed. As a result of trapping of radiation defects (F- and H-aggregate colour centres) by impurity centres the reconstruction of impurity centres takes place, causing a change of mechanical and electrical properties.     

Electrode effects on the electrical properties of chalcogenide films

The effect of Al, Ag and Cr metal electrodes on the electrical properties of CeSeTe films was studied. The relative ease of the diffusion of metallic atoms and the accompanied tendency to nucleation leads to irreversible changes of the film resistivity while annealing. The recrystallization temperature of the chalcogenide film depends strongly on the type of the metal electrode. The observed increase in the values of resistivity after annealing, was interpreted on the basis of charged dangling bond theory.     

Influence of substrate temperature and oxygen/argon flow ratio on the electrical and optical properties of Ga‐doped ZnO thin films prepared by rf magnetron sputtering

Effects of substrate temperature and atmosphere on the electrical and optical properties of Ga‐doped ZnO thin films deposited by rf magnetron sputtering were investigated. The electrical resistivity of Ga‐doped ZnO (GZO) films decreases as the substrate temperature increases from room temperature to 300°C. A minimum resistivity of 3.3 × 10^–4 Ω cm is obtained at 300°C and then the resistivity increases with a further increase in the substrate temperature to 400°C. This change in resistivity with the substrate temperature is related to the crystallinity of the GZO film. The resistivity nearly does not change with the O₂/Ar flow ratio, R for R < 0.25 but increases rapidly with R for R > 0.25. This change in resistivity with R is also related to crystallinity. The crystallinity is enhanced as R increases, but if the oxygen partial pressure is higher than a certain level (R = 0.25 ± 0.10) gallium oxides precipitate at grain boundaries, which decrease both carrier concentration and mobility. Optical transmittance increases as R increases for R < 0.75. This change in transmittance with R is related to changes in oxygen vacancy concentration and surface roughness with R. (© 2006 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Influence of substrate temperature on microcrystalline structure and optical properties of ZnTe thin films

ZnTe thin films were deposited onto well‐cleaned glass substrates kept at different temperatures (Ts = 303, 373 and 423 K), by vacuum evaporation method under the pressure of 10^–5 Torr. The thickness of the film was measured by quartz crystal monitor and verified by the multiple beam interferometer method. The structural characterization was made using X‐ray diffractometer with filtered CuKα radiation. The grain sizes of the microcrystallines in films increases with increase in substrate temperature. The strain (ε), grain size (D) and dislocation density (δ) was calculated and results are discussed based on substrate temperature. Optical behaviour of the film was analyzed from transmittance spectra in the visible region (400–800 nm). The optical transition in ZnTe films is direct and allowed type. The optical band gap energy shows an inverse dependence on substrate temperature and thickness. (© 2006 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Influence of thermal annealing ambient on Ga-doped ZnO thin films

The effect of thermal annealing on the structural, chemical, electrical, and optical properties of Ga-doped ZnO (GZO) films was investigated in various ambients, such as oxygen, nitrogen, and forming gas (95% N₂ 5% H₂). The variation of these properties is thought to be related to the chemisorption and removal of adsorbed oxygen on the GZO film surface. The carrier concentration of the GZO films increased with heat treatment in the forming gas ambient. However, the carrier concentration of the GZO films decreased with heat treatment in oxygen and nitrogen. Annealing under forming gas, oxygen weakly absorbed on the GZO film was removed. Annealing under N- and O-rich conditions, chemisorption of oxygen was dominant. These results were clarified by comparatively analyzing the chemical states of oxygen on the surface of the GZO films.     

Influence of substrate and film thickness on structural,optical and electrical properties of ZnO thin films

Transparent Zinc Oxide (ZnO) thin films have been grown on Si (100) and Sapphire (0001) substrates by RF magnetron sputtering for different growth time intervals (10, 30 and 60 min) to study the substrate and thickness effects. All the films have been grown at a substrate temperature of 450 °C. It has been found that the average growth rate on Si (100) substrate (8.6 nm/min) is higher than that on Sapphire (0001) substrate (2.6 nm/min) in an identical growth condition which clearly shows the virtual role of substrates. The lower growth rate on Sapphire (0001) suggests that the increasingly ordered and uniform growth due to less lattice mismatch. The grown films have been characterized by X‐ray diffraction (XRD), Reflectance, Photoluminescence (PL) and Hall measurements. The XRD result (FWHM) reveals that for lower growth time, the films grown on Si (100) is better than on Sapphire (0001). Conversely, for higher growth time, the films grown on Sapphire (0001) is better than on Si (100). The variation of strain behavior due to thickness on both substrates has been justified by UV‐Vis reflectance, photoluminescence and Hall effect measurements. (© 2011 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Influence of annealing condition on the properties of sputtered hafnium oxide

Hafnium oxide thin films were deposited on p-type (1 0 0) silicon wafers by reactive dc magnetron sputtering. Prior to the deposition of HfO₂ films, a thin Hf film was deposited. Sputtered HfO₂ thin films deposited at room temperature remain amorphous at T<650°C and orthorhombic phases were observed above 650 °C. The monoclinic phase which is a stable HfO₂ polymorphic form appeared after annealing above 800 °C. Capacitance equivalent thickness values decreased and leakage characteristics are improved by the Hf interlayer and O₂ settlement process. The decrease of accumulation capacitance values upon annealing is due to the growth of an interfacial layer upon post-annealing. The flat band voltage (V_FB) shifts negatively due to positive charge generated during post-annealing.     

Influence of selenization temperature on synthesis,morphology, and properties of nanostructured CoSe2 films

Nanostructured cobalt selenide (CoSe₂) thin films were deposited on a glass substrate using the selenization of Co films at different selenization temperatures (300 °C, 400 °C, and 500 °C) in a pure Se vapor for two hours. The morphology and structure of the as‐deposited films shows that the film morphology and crystallinity are affected by the selenization temperature. Increasing the selenization temperature from 300 °C to 400 °C and 500 °C results in a change in the surface and cross sectional morphology. At 300 °C, the Co films have an almost amorphous structure, while at temperatures of 400 and 500 °C, the Co films have a crystalline nanostructure with bilayered morphology. Optical analyses of the CoSe₂ films at 500 °C show a large absorption (α > 1.0 × 10⁵ cm⁻¹) and a direct band gap (∼1.0 eV).