同构MOFs复合氧化石墨烯电极材料构筑高性能超级电容器

在水热条件下一步自组装合成系列同构X-MOF （X₆O （TATB）₄（H⁺）₂·（H₂O）₈·（DMF）₂,X=Zn、Co、Ni; H₃TATB=4,4'',4″-s-triazine-2,4,6-triyl-tribenzoic acid; DMF=N,N-二甲基甲酰胺）和氧化石墨烯（GO）的复合材料（X-MOF@GO）,并探究其作为超级电容器电极材料的电化学性能。通过X射线粉末衍射、X射线光电子能谱和扫描电子显微镜测试证明GO和MOFs复合成功。其中,性能最优的Ni-MOFs@1.5GO （GO的添加量为1.5 mL）的比电容高达694.8 F·g^-1（0.5 A·g^-1）,约是Ni-MOF的2倍。电化学测试结果表明：复合材料X-MOF@1.0GO较其原MOF表现出更大的比电容和更好的倍率性能。在3.5 A·g^-1的电流密度下,1 000次循环充放电后,Ni-MOFs@1.0GO仍保持初始比电容量的81.2%。与活性炭（AC）组装的非对称超级电容器Ni-MOF@1.5GO//AC的性能最优,其功率密度为754.3 W·kg^-1时,能量密度为15.4 Wh·kg^-1,且循环3 000次后比电容保持率约为70.0%,显示出较长的循环寿命。     

碳纸负载碳酸氢镍纳米颗粒的无酶葡萄糖电化学传感器

通过一步水热法在碳纸上原位生长碳酸氢镍纳米颗粒,利用粉末X射线衍射和扫描电子显微镜对材料的结构及形貌进行表征,发现碳纸上负载纯相Ni （HCO₃）₂时具有较多的催化活性位点,利于葡萄糖的催化氧化反应进行。循环伏安法和时间-电流响应曲线表明该电极的检测限为0.98 μmol·L^-1,线性范围为2.95~1.02 mmol·L^-1,灵敏度为935 μA·L·mmol^-1·cm^-2,同时具有优异的选择性及稳定性。此外,该传感器能够实现对乳制品中葡萄糖的快速检测。这些结果表明,过渡金属和导电基底的协同作用会增强复合材料整体的导电性能和催化性能。     

多酸Eu-PMo12O40可逆变色/荧光开关性质对维生素C的光谱检测

将VC等量加入Eu-PMo₁₂O₄₀溶液中,PMo₁₂O₄₀^3-被还原由浅黄色变为蓝色,同时Eu³⁺的荧光淬灭。利用UV-Vis、PL光谱法分别测定不同VC浓度下Eu-PMo₁₂O₄₀的紫外可见光谱、荧光光谱,以700 nm处的吸光度对VC浓度作图,得到VC的线性检测范围为0~0.40 mmol·L^-1、检出限为0.0258μmol·L^-1;以591 nm处的荧光强度对VC浓度作图,获得VC的线性检测范围为0~0.64 mmol·L^-1、检出限为0.0361μmol·L^-1。最后,在VC还原和H₂O₂氧化下,研究了Eu-PMo₁₂O₄₀变色/荧光开关性质的可逆性以及对VC检测的可重复使用性。     

三个二羧酸配体配位聚合物的合成、结构表征和荧光性质

以羧酸配体2,2''-（1,4-亚苯基双（亚甲基））双（硫二基）二苯甲酸（H₂L¹）和2,2''-（2,3,5,6-四甲基-1,4-亚苯基）双（亚甲基）双（硫二基）二苯甲酸（H₂L²）分别与金属盐反应,通过溶剂热方法合成了3个配位聚合物：{[Ni（L¹）（H₂O）₄]·2H₂O}_n （1）、[Zn（L¹）（DMA）₂]_n （2）和[Co（L²）（DMF）₂]_n （3）,其中DMA=N,N-二甲基乙酰胺,DMF=N,N-二甲基甲酰胺。对配合物1~3进行了单晶X射线衍射、元素分析、红外光谱、热重分析、粉末X射线衍射和固体紫外可见光谱测试和表征。单晶X射线衍射表明：3个配合物均为一维锯齿形链状结构,并通过氢键作用形成三维骨架,且配体均表现为反式构象。此外,对配合物2固态荧光性质进行了研究。     

蒽醌基金属-有机笼光氧化性能

将光活性蒽醌配体L¹和L²（L¹=N²,N⁷-双（（2,2''-联吡啶）-5-基）-9,10-蒽醌-2,7-双酰胺,L²=N²,N⁷-双（4-（（2,2''-联吡啶）-5-基）苯基）-9,10-蒽醌-2,7-双酰胺）与锌离子和亚铁离子通过配位自组装构筑得到一系列配合物1-Zn、2-Zn和2-Fe,单晶X射线衍射和电喷雾质谱等表征表明这一系列配合物为“2+3”的M₂L₃型金属-有机超分子结构。将蒽醌基金属-有机笼1-Zn与2-Zn应用于甲苯光催化氧化反应中,结果表明笼状催化剂和底物分子间形成超分子主客体化合物是其能有效氧化甲苯的关键。通过对芳香醇的光氧化反应进一步探究1-Zn与2-Zn的光氧化性能,实验结果表明催化产率受到取代基的电子效应和底物分子的尺寸的影响。     

一种用于检测四环素和对硝基苯酚的高稳定性镉（Ⅱ）金属有机骨架

采用水-溶剂热法合成了1例金属有机骨架（MOF）：{[Cd （L）_0.5（4,4''-bpy）_0.5]·H₂O}_n（1）,其中H₄L=（1,1''∶4'',1″-三联苯）-2,2″,4,4″-四羧酸,4,4''-bpy=4,4''-联吡啶）。通过单晶X射线衍射、元素分析、粉末X射线衍射、热重分析以及红外光谱分析对配合物1的结构进行了表征。单晶结构分析表明1为三维结构,属于单斜晶系,C2/c空间群,Cd （Ⅱ）连接L^4-和4,4''-bpy形成二维平面结构,层与层之间通过L^4-连接,构筑成了三维网状结构。该MOF表现出良好的稳定性并且可以通过荧光猝灭法检测四环素（TET）和对硝基苯酚（4-NP）,四环素和对硝基苯酚的检出限分别为0.15和0.062 μmol·L^-1。此外,还研究了其荧光猝灭机理。1可成功应用于延河水样中TET和4-NP含量的测定。     

氧杂蒽染料修饰钴-硫脲配合物的光解水放氢性能

将具有不同端基的硫脲基团与三苯基磷组分结合,利用所得到的配体合成了2个具有NSP（氮硫磷）鳌合位点的钴-硫脲化合物,并研究了其光解水产氢性能。配合物[Co（L2）（L2''）]（BF₄）_2.5·H₂O·0.5C₂H₅OH（2）（L2=（2-二苯基膦-苯烯基）-氨基硫脲腙-罗丹明6G,L2''=（2-二苯基膦氧-苯烯基）-氨基硫脲腙-罗丹明6G）通过引入罗丹明荧光团与光敏剂分子协同作用,其产氢TON值可以达到2800 mol_H2·mol^-1_cat,其初始TOF值可达到930 mol_H2·mol^-1_cat·h^-1。相同条件下,相比于配合物[Co（L1）（L1''）]（BF₄）·0.5H₂O（1）（L1=（2-二苯基膦-苯烯基）-氨基硫脲腙-硫甲基,L1''=（2-二苯基膦氧-苯烯基）-氨基硫脲腙-硫甲基）,提高了体系的催化活性,可能是由于荧光素分子与配合物2之间的分子间π-π堆积作用有利于光敏剂和光催化剂之间的光致电子转移。     

铕掺杂对Co3O4活化过一硫酸盐降解亚甲基蓝性能的增强

以Co （NO₃）₂和Eu （NO₃）₃为原料,采用草酸盐-热分解法制得了系列不同Co/Eu比例（n_Co/n_Eu）的多孔双金属复合氧化物催化剂,并对其活化过一硫酸盐（PMS）降解亚甲基蓝（MB）的性能进行对比评价。结果表明,按n_Co/n_Eu=9制得的材料（Co₉Eu₁）具有最为优异的活化PMS降解MB的性能。在温度为25℃、催化剂用量和PMS浓度分别为0.10 g·L^-1和0.6 mmol·L^-1的反应条件下,Co₉Eu₁/PMS体系对MB的降解率可达86.66%,而纯Co₃O₄催化下的MB降解率仅为52.62%。Co₉Eu₁出色的催化性能是由于Eu³⁺的缺电子特性增强了对吸附于催化剂表面PMS的极化而使其更易被主催化成分Co₃O₄活化。体系中阴离子C₂O₄^2-和HCO₃^-的存在对Co₉Eu₁/PMS氧化降解MB的性能具有明显抑制作用。猝灭实验和电子顺磁共振谱（EPR）证实Co₉Eu₁/PMS体系中同时存在SO₄^-·、·OH和·O₂^-三种自由基型活性物种以及¹O₂非自由基型活性物种,其中SO₄^-·对MB的氧化降解起关键作用。Co₉Eu₁具有良好的稳定性,在连续4次循环使用中其催化性能未见明显变化。     

三角柔性多羧酸金属有机骨架化合物的合成、结构及荧光性质

以柔性1,3,5-三（4-羧酸苯氧基）苯（H₃TCPB）为配体,以4,4''-联吡啶（4,4''-BPY）为辅助配体,在溶剂热条件下合成了2个新颖的分别具有三核锌簇和三核钴簇的金属有机骨架化合物：{[Zn₃（TCPB）₂（4,4''-BPY）]·DMF·3H₂O}_n（1）和{[Co_1.5（TCPB）（DMF）（H₂O）]·DMF}_n（2）,通过单晶X射线衍射,红外光谱,元素分析,热重分析和粉末X射线衍射对其结构进行了表征。单晶X射线衍射分析表明化合物1属于三斜晶系,P1空间群,表现出三维（3,8）连接的网状结构,拓扑符号为：{4³}₂·{4⁶·6¹⁸·8⁴}·{6};化合物2也属于三斜晶系,P1空间群,为二维（3,6）连接的网络层状结构,拓扑符号为：{4³}₄·{4⁶·6¹⁸·8⁴}。此外,荧光性质研究表明固态化合物¹在室温条件下发射出源于TCPB^3-和4,4''-BPY配体的淡蓝色荧光,而化合物2在相似的条件下没有荧光发射。     

柔性配体构筑的三个构象多样的镧系羧酸配位聚合物:合成,结构和荧光性质

利用2,2''-（1,4-亚苯基）二（亚苯基）二（硫基）苯二羧酸（H₂L¹）和2,2''-（2,3,5,6-四甲基-1,4-亚苯基）二（亚甲基）二（硫基）苯二甲酸（H₂L²）2个柔性二羧酸分别与镧系金属盐反应,通过溶剂热方法合成了3个配位聚合物：{[（NH₂（CH₃）₂][Nd（L¹）₂（DMF）]·2DMF}_n（1）和{[Ln（L²）_1.5（H₂O）（DMF）₂]·2DMF}_n[Ln=Ce（2）,Pr（3）]。利用元素分析、红外、粉末X射线衍射、热重分析等对配合物进行了表征。X射线单晶衍射分析表明：3个配合物均为二维的层状结构,并且2个配体在配合物中表现出不同的构象。（L¹）^2-在配合物1中表现出顺式和反式2种构象,（L²）^2-在配合物2和3中仅表现出反式构象。此外,对配合物的热稳定性和荧光性质也进行了研究。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.