Monitoring solid phase synthesis reactions with electrochemical impedance spectroscopy (EIS)

This work describes the use of electrochemical impedance spectroscopy (EIS) as a means to monitor solid phase synthesis on resin beads. EIS was used to track changes during the swelling of beads in various solvents, during three typical reactions and throughout cleavage of the final product from the bead. The impedance response was investigated in a chemical reactor and was found to be faintly sensitive to the resin swelling and solvent flow. The position of the electrode within the reactor was found to be critical as polystyrene based beads float or sink dependent upon the solvent used. However, by choosing electrode position it was possible to monitor reaction progress on beads or within the bulk reactant/product mixture. Of the three typical chemical reactions studied impedance spectroscopy successfully followed two. Fitting of the impedance data to an equivalent electrical circuit provided an estimate as to the relative contribution of capacitive and resistive components to the overall response. Kinetic data from two reactions were also modelled, in both cases complex kinetics was observed, in close agreement with other studies.     

Microparticle sampling by electrowetting-actuated droplet sweeping

This paper describes a new microparticle sampler where particles can be efficiently swept from a solid surface and sampled into a liquid medium using moving droplets actuated by the electrowetting principle. We successfully demonstrate that super hydrophilic (2 microm and 7.9 microm diameter glass beads of about 14 degrees contact angle), intermediate hydrophilic (7.5 microm diameter polystyrene beads of about 70 degrees contact angle), and super hydrophobic (7.9 microm diameter Teflon-coated glass beads and 3 microm size PTFE particles of over 110 degrees contact angles) particles on a solid surface are picked up by electrowetting-actuated moving droplets. For the glass beads as well as the polystyrene beads, the sampling efficiencies are over 93%, in particular over 98% for the 7.9 microm glass beads. For the PTFE particles, however, the sampling efficiency is measured at around 70%, relatively lower than that of the glass and polystyrene beads. This is due mainly to the non-uniformity in particle size and the particle hydrophobicity. In this case, the collected particles staying (adsorbing) on the air-to-water interface hinder the droplet from advancing. This particle sampler requires an extremely small amount of liquid volume (about 500 nanoliters) and will thus be highly compatible and easily integrated with lab-on-a-chip systems for follow-up biological/chemical analyses.     

From planar defect in opal to planar defect in inverse opal

We demonstrate a facile method of fabricating opal and inverse opal structures with a planar defect. A single layer of silica beads was embedded into polystyrene opals by combining an inward-growing self-assembly method with spin-coating technique. After the infiltration of silica followed by the removal of the polystyrene beads by calcination, an inverted structure was obtained. The silica beads were connected together by the infiltrated silica, thus a solid silica phase with the silica beads as a planar defect embedded in the inverse silica opal was obtained. The thickness of the defect layer can be adjusted by changing the size of the silica beads. Scanning electron microscope images showed the good quality of the crystal and the uniformity of the defect layer. Optical transmission spectra indicated the existence of a defect state induced by the defect layer in both the opal and inverse opal structures. High-cost techniques such as lithography and chemical vapor deposition are not involved in the fabrication of inverse opals with planar defects.     

A new floating electrode structure for generating homogeneous electrical fields in microfluidic channels

In this article a new parallel electrode structure in a microfluidic channel is described that makes use of a floating electrode to get a homogeneous electrical field. Compared to existing parallel electrode structures, the new structure has an easier production process and there is no need for an electrical connection to both sides of the microfluidic chip. With the new chip design, polystyrene beads suspended in background electrolyte have been detected using electrical impedance measurements. The results of electrical impedance changes caused by beads passing the electrodes are compared with results in a similar planar electrode configuration. It is shown that in the new configuration the coefficient of variation of the impedance changes is lower compared to the planar configuration (0.39 versus 0.56) and less dependent on the position of the beads passage in the channel as a result of the homogeneous electrical field. To our knowledge this is the first time that a floating electrode is used for the realization of a parallel electrode structure. The proposed production method for parallel electrodes in microfluidic channels can easily be applied to other applications.     

Structural properties of atactic polystyrene adsorbed onto solid surfaces

In the present work, we are studying the local conformation of chains in a thin film of polystyrene adsorbed on a solid substrate by using atomistically detailed simulations. The simulations are carried out by using the readily available and massively parallel molecular dynamics code known as LAMMPS. In particular, a special emphasis is given to the density and orientation of side chains (which consist of phenyl groups and methylene units) at solid/polymer and polymer/vacuum interfaces. Three types of substrates were used in our study: α-quartz, graphite, and amorphous silica. Our investigation was restricted to atactic polystyrene. Our results show that the density and structural properties of side chains depend on the type of surface. An excess of phenyl rings is observed near the α-quartz substrate while the film adsorbed on graphite is depleted in C(6)H(5). Moreover, the orientation of the rings and methylene units on the substrate/film interface show a strong dependence on the type of the substrate, while the rings at the film/vacuum interface show a marked tendency to point outward, away from the film. The results we obtained are in a large part in good agreement with previous experimental and simulation results.     

Quantum dot-labelled polymer beads by suspension polymerisation

CdSe quantum dots with polymerisable ligands have been incorporated into polystyrene beads, via a suspension polymerisation reaction, as a first step towards the optical encoding of solid supports for application in solid phase organic chemistry.     

Sustainable photochemistry: solvent-free singlet oxygen-photooxygenation of organic substrates embedded in porphyrin-loaded polystyrene beads

A solvent-free photooxygenation process that uses organic substrates embedded in porphyrin-loaded polystyrene beads as solid support is described and applied for ene- and [4 + 2]-cycloaddition reactions involving singlet oxygen (1 delta g).     

高分子固载化Lewis酸催化剂——聚苯乙烯-五氯化锑复合物

<正> 高分子催化剂是近年来十分活跃的新领域。Sket等人曾将BF_3和AlCl_3与复合物;——PS-sbCl,复合物(未交联聚苯乙烯与SbCl,反应而成)其中1—4分别 为1.0％,1.3％,1.5％,2.5％的氯仿溶液聚苯乙烯(PS)反应制成稳定的复合物,它对酯化、缩醛、缩酮等有机反应有良好的催化作用。本文首次将在空气中强烈水解的SbCl_3与聚苯乙烯交联白球(含二乙烯基苯4％,     

A self-assembling polymer-bound rotaxane under thermodynamic control

The thermodynamically controlled self-assembly of a neutral donor-acceptor rotaxane, stoppered via porphyrin coordination and bound to polystyrene beads is described, and the dynamic equilibrium between solid and solution phases has been examined by HR MAS nmr spectroscopy.     

Simple and efficient solid-phase preparation of azido-peptides

A shelf-stable and easily prepared diazotransfer reagent, imidazole-1-sulfonyl azide hydrochloride, was used to transform the N-terminus of a model peptide on solid phase into an azide moiety. It is demonstrated that this conversion was accomplished within 30 min with high efficiency under aqueous conditions on a NovaPEG resin or in DMF on polystyrene beads.     

Preparation of rapidly disintegrating tablets containing itraconazole solid dispersions

The disintegratability of tablets prepared from two types of solid dispersions containing the water-soluble polymer TC-5 and the enteric polymer HP-55 as an excipient were compared. The disintegratability was better in the tablets of solid dispersions containing non-water-soluble HP-55 than those containing TC-5. In consideration of the dissolubility of solid dispersions containing HP-55, the mean diameter of the solid dispersion (coating powder) must be controlled to 120 microm or less, but as this markedly increases the adhesion/aggregation tendency of the particles (angle of repose: 47 degrees ), control of the adhesion/aggregation tendency emerged as another problem. Therefore, surface-modification was performed in a high-speed agitating granulator using 0.1% light anhydrous silicic acid as a surface modifier, and marked improvement in the flowability was observed. This made continuous tableting using a rotary tablet machine possible even with the poorly flowable solid dispersions. Also, in tableting of the solid dispersions, no recrystallization of amorphous itraconazole by the tableting pressure was observed, and the tablets maintained satisfactory dissolubility. Moreover, it was possible to obtain the rapidly disintegrating tablets with very satisfactory properties, i.e., a tablet hardness of 30 N or higher and a disintegration time of 30 s or less, by the addition of croscarmellose as a disintegrant at 2% to the surface-modified solid dispersion and selection of the tableting pressure at 4.5 kN.     

In situ observation of molecular diffusion in solid supports using two-photon fluorescence microscopy

We demonstrate that two-photon fluorescence microscopy is a useful tool for monitoring the diffusion of molecules through polymeric solid supports. As a proof of principle, TentaGel beads were bound to a cover slip, and diffusion of Rhodamine 6G through single beads was observed in real time. Diffusion experiments performed in 40 different beads indicate that there is a considerable degree of heterogeneity in diffusion rates from bead to bead.     

Micro solid phase spectrophotometry in a sequential injection lab-on-valve platform for cadmium,zinc, and copper determination in freshwaters

This work describes the development of a solid phase spectrophotometry method in a μSI-LOV system for cadmium, zinc, and copper determination in freshwaters. NTA (Nitrilotriacetic acid) beads with 60–160 μm diameter were packed in the flow cell of the LOV for a μSPE column of 1 cm length. The spectrophotometric determination is based on the colourimetric reaction between dithizone and the target metals, previously retained on NTA resin. The absorbance of the coloured product formed is measured, at 550 nm, on the surface of the NTA resin beads in a solid phase spectrophotometry approach.     

Adsorption of bovine alpha-lactalbumin on suspended solid nanospheres and its subsequent displacement studied by NMR spectroscopy

Detailed knowledge of the adsorption-induced conformational changes of proteins is essential to understand the process of protein adsorption. However, not much information about these conformational changes is available. Here, the adsorption of calcium-depleted (APO)- and calcium-containing (HOLO)-bovine alpha-lactalbumin (BLA) on suspended solid polystyrene nanospheres and their subsequent displacement by a surfactant are studied by NMR spectroscopy. To our knowledge, this is the first time that adsorption of proteins on solid nanospheres, with both components present in the NMR sample, is studied by this method. High-quality one-dimensional and two-dimensional 1H NMR spectra of nonadsorbed APO- and HOLO-BLA in the presence of BLA- and/or surfactant-covered solid polystyrene nanospheres in suspension are obtained using standard NMR procedures. BLA and surfactant molecules that are adsorbed on the polystyrene nanospheres give rise to extremely broadened proton resonances. This can be exploited to determine the amount of adsorbed protein and of adsorbed surfactant in a system containing protein, nanospheres, and surfactant, without disturbing the equilibrium of the system. Two-dimensional 1H NMR spectroscopy shows that the chemical shifts of the backbone amide protons of HOLO-BLA after its adsorption and subsequent displacement from polystyrene nanospheres by the surfactant 3-[(3-cholamidopropyl)-dimethylammonio]-1-propanesulfonate (CHAPS) are identical to those of native HOLO-BLA. The adsorption-induced unfolding of BLA to a molten globule state on polystyrene nanospheres is thus fully reversible at the residue level upon CHAPS-induced displacement of BLA. The latter is the now fulfilled essential requirement that enables the future indirect study, at the residue level, of the conformational characteristics of BLA adsorbed on polystyrene nanospheres by hydrogen/deuterium exchange and NMR spectroscopy. The results presented show that NMR spectroscopy is clearly feasible to study the adsorption of BLA on suspended polystyrene nanospheres. This technique should be applicable to the study of the adsorption of other proteins on other surfaces as well.     

Preparation and characterization of hollow spheres of rutile

Hollow spherical particles of rutile were obtained by coating colloidal polystyrene beads with a titanium oxide hydrate layer and subsequently calcining at elevated temperatures under an oxygen atmosphere. In order to investigate the optimum conditions for the preparation of these hollow beads the maximum temperature and heating rate were systematically varied. The dimensions of the voids and the shell thickness of the hollow beads can be tailored by the size of the polystyrene beads and the thickness of the inorganic layer, respectively.     

Chromium-mediated aldol and homoaldol reactions on solid support directed towards an iterative polyol strategy

Chromium-Reformatsky and chromium-homoaldol reactions run under neutral and mild reaction conditions. They are highly chemoselective, tolerant towards most common functional groups, and are not prone to retroaldol reactions. Initial studies directed to transfer these homogeneous chromium-mediated solution-phase reactions to solid phase are presented. The main objective was to develop a methodology to aid a combinatorial iterative strategy to polyols (polyketides) on solid phase. A general reactivity problem was observed with polystyrene based resins compared to the solution-phase reactions, independent if the electrophilic (aldehyde) or nucleophilic (bromide) end of the polyol chain was supported to the resin. A complicated penetration, or loss of the polar solvent environment after penetration into the resin, might be responsible for the reduced reactivity. Application of either a soluble polystyrene resin or a polystyrene resin with a polar polyethylene glycol tether resulted in improved yields.     

Amplification immunoassay for the determination of Hepatitis B surface antigen

A sensitive sandwich immunoassay for the determination of Hepatitis B surface antigen (HBs) was developed, using a cascade system of Limulus amebocyte lysate as a signal amplification system. Lipopolysaccharide (LPS) was conjugated to anti-HBs antibody. Anti-HBs antibody was adsorbed to polystyrene beads. First, HBs were reacted to solid phase anti-HBs antibody (a-HBs). After the reaction, the beads were rinsed, and were then reacted with a-HBs-LPS. Then, LPS activity specifically bound to the beads was measured. HBs could be measured in the range of 10(-10)-10(-12) g/mL.     

N‐bromo‐hydantoin grafted polystyrene beads: Synthesis and nano‐micro beads characteristics for achieving controlled release of active oxidative bromine and extended microbial inactivation efficiency

N‐bromo‐hydantoin and N‐bromo‐5,5′‐dimethylhydantoin conjugated polystyrene beads were synthesized from chloromethyl polystyrene beads which differ in their particles size, crosslinking, nano‐micro porosity, and tunnels size on the surface, in order to study the effect of these parameters on oxidative halogen release and resultant activity, for water purification applications. The synthesized beads were characterized using elemental analysis, FT‐IR, solid state ¹³C‐NMR, and scanning electron microscope (SEM). The conjugation yield and kinetics in different solvents and bromine loading capacity were studied. The N‐bromoamine polystyrene beads were tested for water decontamination according to NSF 231 protocol. The release of active bromine was analyzed by spectrophotometer using a DPD‐1 kit and also studied the antimicrobial activity against Escherichia coli and MS2 phages. Bead's nano‐micro characteristics were found critical for oxidative halogen release control: rate stabilization and modulation, extension and also influences antimicrobial activity. The synthesized beads exhibited extended and stable release of bromine, 6 and 4 log reduction for E. coli and MS2, respectively for 250 L of passing contaminated water. Thus, N‐halamine hydantoins conjugated polystyrenes, chemically or kinetically release modified should have applications as disinfectants in water purification systems as well as medical field. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 596–610     

Ethylene polymerization with porous polystyrene spheres supported Cp2ZrCl2 catalyst

A catalyst with porous polystyrene beads supported Cp₂ZrCl₂ was prepared and tested for ethylene polymerization with methylaluminoxane as a cocatalyst. By comparison, the porous supported catalyst maintained higher activity and produced polyethylene with better morphology than its corresponding solid supported catalyst. The differences between activities of the catalysts and morphologies of the products were reasonably explained by the fragmentation processes of support as frequently observed with the inorganic supported Ziegler–Natta catalysts. Investigation into the distribution of polystyrene in the polyethylene revealed the fact that the porous polystyrene supported catalyst had undergone fragmentation during polymerization. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 3313–3319, 2003     

Crosslinked Polystyrene Beads Modified with Sulfonyl Groups and Their Application in Aromatic/Aliphatic Hydrocarbons Separation

The separation of aromatic hydrocarbons from aromatic/aliphatic mixtures was investigated with cross- linked polystyrene（CPS） beads modified with sulfonyl groups. Three sulfonating agents, i.e. benzenesulfonyl chlo- ride（BsCl）, 4-toluene sulfonyl chloride（TsC1） and methanesulfonyl chloride（MsC1） were used to prepare sulfonyl CPS beads by Friedel-Crafts reaction. The CPS beads modified with BsC1 exhibited higher sulfonation rate than those modified with MsC1 and TsCI and obtained optimum selectivity in the experiments of toluene/n-heptane separation. Further separation tests with various other aromatic/aliphatic mixtures were carried out at an initial aromatic concen- tration of 13%（mass fraction） with the results showing that the modified beads have preferential selectivity for aro- matic hydrocarbons in all aromatic/aliphatic mixtures, and especially a separation factor of 8.21 and a swelling ratio of 30% for toluene/cyclohexane system. The thermal stability and regeneration test indicate that the used polystyrene beads can be recovered through heat-drying and reused effectively.