Hydrogels in aqueous phases of polyvinylalcohol (PVA), surfactants and clay minerals

Aqueous solutions of synthetic clay minerals have been studied in the presence of surfactants and water-soluble polyvinylalcohol (PVA). The PVAs (PVA 1, PVA 2) had a molecular weight of about 10⁵ Dalton and a degree of hydrolysis of 82%. The PVA-samples were surface active and lowered the surface tension to 43 mN/m. As a consequence of their amphiphilic nature the PVA molecules bind strongly to clay mineral particles. On saturation the clay mineral particles adsorb the fivefold weight of PVA of their own weight. It is concluded that the thickness of the adsorbed layers on both sides of the clay mineral is in the range of the hydrodynamic diameter of the PVA-coils in the bulk phase.When the clay mineral particles are not saturated with PVA, they act as cross-linking agents for the PVA. The whole systems are physically cross-linked and assume gel-like properties. Rheological measurements show that samples behave like soft matter with a yield stress value. All of them have a frequency independent storage modulus which is an order of magnitude larger than the loss modulus. The hydrogels become stronger as PVA concentration increases.Small amounts of cationic surfactants bind on the clay mineral. The interface of the clay mineral becomes more hydrophobic and the binding of the PVA on the clay mineral is strengthened. With rising concentration of the surfactant the surfactant molecules bind on PVA and the PVA becomes hydrophilic. As a consequence the PVA can no longer bind on the clay mineral and the gels transform to viscous and turbid solutions. Small amounts of cationic surfactants therefore stiffen the hydrogels while larger amounts cause phase separation and a solution with low viscosity. Anionic surfactants like SDS do not bind on the clay mineral, but strongly on the PVA. With increasing SDS concentration, the hydrogels become stiffer at first but thereafter they break and transform to viscous fluids.In PVA-solutions without the clay minerals both cationic and anionic surfactants bind to the PVAs in the aqueous solution. With increasing concentration of surfactant, the viscosities of the solutions pass over a maximum. In this respect the PVAs behave like hydrophobically modified water soluble polymers. The surfactants bind to the hydrophobic microdomain and thereby crosslink the polymer molecules. On saturation the polyvinyl alcohol with anionic surfactant become hydrophilic and the network character disappears to a certain extent.     

表面活性剂对共轭聚合物荧光性质及电荷转移的影响

探讨了表面活性剂存在下, 水溶性阴离子共轭聚合物聚[5-甲氧基-2-(3-磺酰化丙氧基)-1,4-苯撑乙烯](简写为MPS-PPV)的微环境变化对荧光性质及电荷转移的影响. 结果表明, 阳离子表面活性剂及非离子表面活性剂使MPS-PPV荧光增强, 阴离子表面活性剂使其荧光先增强后减弱; 在MPS-PPV/表面活性剂体系中加入电子接受体Pd^2＋, 发现非离子表面活性剂体系的荧光猝灭效率提高, 阴离子及阳离子表面活性剂体系荧光猝灭效率下降. 此研究对研制基于阴离子共聚物的新型生物化学传感器具有一定的指导意义.     

Manipulation of the adsorption of ionic surfactants onto hydrophilic silica using polyelectrolytes

This paper demonstrates the use of polyelectrolytes to modify and manipulate the adsorption of ionic surfactants onto the hydrophilic surface of silica. We have demonstrated that the cationic polyelectrolyte poly(dimethyl diallylammonium chloride), poly-dmdaac, modifies the adsorption of cationic and anionic surfactants to the hydrophilic surface of silica. A thin robust polymer layer is adsorbed from a dilute polymer/surfactant solution. The resulting surface layer is cationic and changes the relative affinity of the cationic surfactant hexadecyl trimethylammonium bromide, C16TAB, and the anionic surfactant sodium dodecyl sulfate, SDS, to adsorb. The adsorption of C16TAB is dramatically reduced. In contrast, strong adsorption of SDS was observed, in situations where SDS would normally have a low affinity for the surface of silica. We have further shown that subsequent adsorption of the anionic polyelectrolyte sodium poly(styrene sulfonate), Na-PSS, onto the poly-dmdaac coated surface results in a change back to an anionic surface and a further change in the relative affinities of the cationic and anionic surfactants for the surface. The relative amounts of C16TAB and SDS adsorption depend on the coverage of the polyelectrolyte, and these preliminary measurements show that this can be manipulated.     

Foaming and foam stability for mixed polymer-surfactant solutions: effects of surfactant type and polymer charge

Solutions of surfactant-polymer mixtures often exhibit different foaming properties, compared to the solutions of the individual components, due to the strong tendency for formation of polymer-surfactant complexes in the bulk and on the surface of the mixed solutions. A generally shared view in the literature is that electrostatic interactions govern the formation of these complexes, for example between anionic surfactants and cationic polymers. In this study we combine foam tests with model experiments to evaluate and explain the effect of several polymer-surfactant mixtures on the foaminess and foam stability of the respective solutions. Anionic, cationic, and nonionic surfactants (SDS, C(12)TAB, and C(12)EO(23)) were studied to clarify the role of surfactant charge. Highly hydrophilic cationic and nonionic polymers (polyvinylamine and polyvinylformamide, respectivey) were chosen to eliminate the (more trivial) effect of direct hydrophobic interactions between the surfactant tails and the hydrophobic regions on the polymer chains. Our experiments showed clearly that the presence of opposite charges is not a necessary condition for boosting the foaminess and foam stability in the surfactant-polymer mixtures studied. Clear foam boosting (synergistic) effects were observed in the mixtures of cationic surfactant and cationic polymer, cationic surfactant and nonionic polymer, and anionic surfactant and nonionic polymer. The mixtures of anionic surfactant and cationic polymer showed improved foam stability, however, the foaminess was strongly reduced, as compared to the surfactant solutions without polymer. No significant synergistic or antagonistic effects were observed for the mixture of nonionic surfactant (with low critical micelle concentration) and nonionic polymer. The results from the model experiments allowed us to explain the observed trends by the different adsorption dynamics and complex formation pattern in the systems studied.     

Interaction between the water soluble poly{1,4-phenylene-[9,9-bis(4-phenoxy butylsulfonate)]fluorene-2,7-diyl} copolymer and ionic surfactants followed by spectroscopic and conductivity measurements

The interaction has been studied in aqueous solutions between a negatively charged conjugated polyelectrolyte poly{1,4-phenylene-[9,9-bis(4-phenoxybutylsulfonate)]fluorene-2,7-diyl} copolymer (PBS-PFP) and several cationic tetraalkylammonium surfactants with different structures (alkyl chain length, counterion, or double alkyl chain), with tetramethylammonium cations and with the anionic surfactant sodium dodecyl sulfate (SDS) by electronic absorption and emission spectroscopy and by conductivity measurements. The results are compared with those previously obtained on the interaction of the same polymer with the nonionic surfactant C12E5. The nature of the electrostatic or hydrophobic polymer-surfactant interactions leads to very different behavior. The polymer induces the aggregation with the cationic surfactants at concentrations well below the critical micelle concentration, while this is inhibited with the anionic SDS, as demonstrated from conductivity measurements. The interaction with cationic surfactants only shows a small dependence on alkyl chain length or counterion and is suggested to be dominated by electrostatic interactions. In contrast to previous studies with the nonionic C12E5, both the cationic and the anionic surfactants quench the PBS-PFP emission intensity, leading also to a decrease in the polymer emission lifetime. However, the interaction with these cationic surfactants leads to the appearance of a new emission band (approximately 525 nm), which may be due to energy hopping to defect sites due to the increase of PBS-PFP interchain interaction favored by charge neutralization of the anionic polymer by cationic surfactant and by hydrophobic interactions involving the surfactant alkyl chains, since the same green band is not observed by adding either tetramethylammonium hydroxide or chloride. This effect suggests that the cationic surfactants are changing the nature of PBS-PFP aggregates. The nature of the polymer and surfactant interactions can, thus, be used to control the spectroscopic and conductivity properties of the polymer, which may have implications in its applications.     

Structure of a hydrophilic-hydrophobic block copolymer and its interactions with salt and an anionic surfactant

The aggregation of a hydrophilic-hydrophobic diblock copolymer consisting of poly(2-(dimethylamino)ethyl methacrylate) (PDMAEMA) and poly(methyl methacrylate) (PMMA) in aqueous solution has been investigated by small-angle neutron scattering. This polybase is extensively protonated at low pH and forms micelles with a dense core of PMMA and a diffuse coronal layer of cationic PDMAEMA. Addition of salt induced micellar growth, brought about by charge screening and more efficient packing of the chains. As a result, the aggregation number increased from 8 up to 31. A similar effect was observed at low concentrations of an anionic surfactant, sodium dodecyl sulfate (SDS) since the net cationic charge in the hydrophilic coronal layer was reduced due to surfactant binding. However, at higher surfactant concentrations, a drastic structural reorganization occurred, as the PMMA became solubilized into the SDS micellar cores and the PDMAEMA chains interacted with the surfactant micelles, resulting in a "pearl-necklace" structure. The presence of the cationic polyelectrolyte significantly increased the population of SDS micelles by effectively lowering the critical micelle concentration of this anionic surfactant.     

In situ AFM studies on self-assembled monolayers of adsorbed surfactant molecules on well-defined H-terminated Si(111) surfaces in aqueous solutions

The formation of self-assembled monolayers (SAMs) of adsorbed cationic or anionic surfactant molecules on atomically flat H-terminated Si(111) surfaces in aqueous solutions was investigated by in situ AFM measurements, using octyl trimethylammonium chloride (C8TAC), dodecyl trimethylammonium chloride (C12TAC), octadecyl trimethylammonium chloride (C18TAC)) sodium dodecyl sulfate (STS), and sodium tetradecyl sulfate (SDS). The adsorbed surfactant layer with well-ordered molecular arrangement was formed when the Si(111) surface was in contact with 1.0x10(-4) M C18TAC, whereas a slightly roughened layer was formed for 1.0x10(-4) M C8TAC and C12TAC. On the other hand, the addition of alcohols to solutions of 1.0x10(-4) M C8TAC, C12TAC, or SDS improved the molecular arrangement in the adsorbed surfactant layer. Similarly, the addition of a salt, KCl, also improved the molecular arrangement for both the cationic and anionic surfactant layers. Moreover, the adsorbed surfactant layer with a well-ordered structure was formed in a solution of mixed cationic (C12TAC) and anionic (SDS) surfactants, though each surfactant alone did not form the well-ordered layer. These results were all explained by taking into account electrostatic repulsion between ionic head groups of adsorbed surfactant molecules as well as hydrophobic interaction between their alkyl chains, which increases with the increasing chain length, together with the increase in the hydrophobic interaction or the decrease in the electrostatic repulsion by incorporating alcohol molecules into the adsorbed surfactant layer, the decrease in the electrostatic repulsion by increasing the concentration of counterions, and the decrease in the electrostatic repulsion by alternate arrangement of cationic and anionic surfactant molecules. The present results have revealed various factors to form the well-ordered adsorbed surfactant layers on the H-Si(111) surface, which have a possibility of realizing the third generation surfaces with flexible structures and functions easily adaptable to circumstances.     

Hydrophobically Modified Polyelectrolytes: V. Interaction of Fluorocarbon Modified Poly (acrylic acid) with Various Added Surfactants

The interactions between fluorocarbon‐modified poly (sodium acrylate) and various kinds of added surfactants have been studied by means of viscometric measurement. Association behavior was found in both hydrogenated and fluorinated anionic, nonionic and cationic surfactants. Among them, the interactions between fluorocarbon‐modified poly (sodium acrylate) and cationic surfactants are the strongest, owing to the cooperation of both electrostatic attractions and hydrophobic associations. The anionic surfactants have the weakest effects on the solution properties because of the existence of unfavorable electrostatic repulsion. The hydrophobic interactions between copolymers and fluorinated surfactants are much stronger than those between copolymers and hydrogenated surfactants.     

The role of initiation in the synthesis of silica/poly(methyl methacrylate) nanocomposite latex particles through emulsion polymerization

Silica/poly(methyl methacrylate) nanocomposite latex particles have been synthesized by emulsion polymerization of methyl methacrylate using a nonionic surfactant: nonylphenol poly(oxyethylene) and three different initiators, namely: 2,2′-azobis(2-amidinopropane) dihydrochloride (AIBA), potassium persulfate (KPS) and azobis(isobutyronitrile) (AIBN), being cationic, anionic and nonionic, respectively. A silica sol with an average diameter of 68 nm was used as the seed. The polymerization reaction was conducted under alkaline conditions in order to evaluate the role of the surface charge of the hydrophilic silica on the coating reaction. AIBA was found to be adsorbed on the silica surface owing to electrostatic interactions of the amidine function of the cationic initiator with the silanolate groups of the oxide surface, while the anionic and the nonionic initiators did not adsorb on silica under the same conditions. Nonetheless, whatever the nature of the initiator, polymerization took place on the silica particles as evidenced by transmission electron microscopy. The extent of interaction between the inorganic surface and the polymer particles was quantified by means of ultracentrifugation and a material balance. As much as 65% by weight of the total polymer formed was found to be present at the silica surface using AIBA, while only 40% for KPS and 25% for AIBN was found to cover the silica particles under alkaline conditions. We demonstrate that by using a cationic initiator and by controlling the pH of the suspension it is possible to significantly decrease the amount of free polymer. Coating of the silica particles took place through a kind of in situ heterocoagulation mechanism. Received: 8 December 2000 Accepted: 22 February 2001     

On the role of initiator in emulsion polymerization

The use of nonionic poly(ethylene glycol)-azo-initiators instead of ionic initiators in emulsion polymerizations offers interesting possibilities for modifying the colloidal and polymeric properties of polymer dispersions. Experimental results are presented for various kinds of anionic, cationic, and nonionic stabilizers as well as for peroxodisulfate initiators with different counter ions (ammonium and potassium). For example, in a styrene emulsion polymerization (with monomer to water mass ratio of 1:4 at a given concentration of 1% with respect to monomer mass of either an anionic or a cationic surfactant), the replacement of either peroxodisulfate or 2,2'-azobis(2-amidinopropane)dihydrochloride by a poly(ethylene glycol)-azo-initiator (with a poly(ethylene glycol) molecular weight of 200 g mol^-1) leads to particles with considerably smaller size, polymers with higher molecular weight, and latexes with higher viscosity.     

Investigation of the interactions in emulsions stabilized by a polymeric surfactant and its mixtures with an anionic surfactant

 The interaction of a nonionic polymeric surfactant with an anionic surfactant at the oil–water interface has been studied by its effects on the droplet size, stability and rheology of emulsions. Oil-in-water (o/w) emulsions were prepared using isoparaffinic oil and mixtures of a nonionic polymeric surfactant with an anionic surfactant. The macro-molecular surfactant was a graft copolymer with a backbone of polymethyl methacrylate and grafted polyethylene oxide (a graft copolymer with PEO chains of MW=750). The anionic surfactant was sodium dodecyl sulfate (SDS). The stabiliza-tion of the emulsion droplets was found to be different when using one or the other surfactant. The mechanism of stabilization of emulsion droplets by the macro-molecular surfactant is of the steric type while the stabilization by anionic surfactant is of the electrostatic repulsion type. Emulsions stabilized with mixtures present both types of stabilization. Other effects on the preparation and stabilization of emulsions were found to be dependent on properties associated with the surfactant molecular weight such as the Marangoni effect and Gibbs elasticity. The initial droplet size of the emulsions showed a synergistic effect of the surfactant combination, showing a minimum for the mixtures compared to the pure components. Emulsion stability also shows a synergistic interaction of both surfactants. Rheological measurements allow for the estimation of the interparticle interaction when measured as a function of volume fraction. Most of the effects observed can be attributed to the differences in interfacial tension and droplet radius produced by both surfactants and their mixtures. The elastic moduli are well explained on the basis of droplet deformation. Ionic versus steric stabilization produce little difference in the observed rheology, the only important differences observed concerned the extent of the linear viscoelasticity region. Received: 22 November 1996 Accepted: 24 March 1997     

Polyelectrolyte modified solid surfaces: the consequences for ionic and mixed ionic/nonionic surfactant adsorption

This paper describes how the cationic polyelectrolyte, polyDMDAAC (poly(dimethyl diallylammonium chloride)), is used to manipulate the adsorption of the anionic surfactant SDS and the mixed ionic/nonionic surfactant mixture of SDS (sodium dodecyl sulfate)/C(12)E(6) (monododecyl hexaethylene glycol) onto the surface of hydrophilic silica. The deposition of a thin robust polymer layer from a dilute polymer/surfactant solution promotes SDS adsorption and substantially modifies the adsorption of SDS/C(12)E(6) mixtures in favor of a surface relatively rich in SDS compared to the solution composition. Different deposition conditions for the polyDMDAAC layer are discussed. In particular, at higher solution polymer concentrations and in the presence of 1 M NaCl, a thicker polymer layer is deposited and the reversibility of the surfactant adsorption is significantly altered.     

Sorption of anionic amphiphilic block copolymers by a network polycation

The interaction of amphiphilic block copolymers comprising an anionic block (polyacrylate or polymethacrylate) and a hydrophobic block (polystyrene, poly(butyl acrylate) or polyisobutylene) with lightly crosslinked poly(N,N-diallyl-N,N-dimethylammonium chloride) is studied for the first time. It is shown that the cationic hydrogel can sorb anionic amphiphilic block copolymers via electrostatic interaction with the corona of block copolymer micelles. The rate of sorption of block copolymer polyelectrolytes is significantly lower than the rate of sorption of linear polyions and is controlled by the lengths of the hydrophilic and hydrophobic blocks and the flexibility of the latter blocks. The sorption of amphiphilic block copolymers is accompanied by their self-assembly in the polycomplex gel and formation of a continuous hydrophobic layer impermeable to water and the low-molecular-mass salt dissolved in it.     

The effect of surfactants on adsorbed layers of a cationic polyelectrolyte

A comparative study of the influence of anionic (sodium dodecyl sulfate, SDS), cationic (tetradecyltrimethylammonium bromide, TTAB) and non-ionic (penta-ethyleneglycol mono n-dodecyl ether, C₁₂E₅) surfactants on the structure and composition of adsorbed layers of cationic hydrophobically modified hydroxyethylcellulose (Quatrisoft LM 200) on hydrophilic surfaces (mica and silica) was carried out using surface force apparatus andin situ null ellipsometry. It is shown that a complex interplay of electrostatic, hydrophobic, and steric effect govern polymer/surfactant/surface interactions and that the effect of surfactant addition strongly depends on its nature and concentration.Both anionic and non-ionic surfactants exhibit aggregation on the polymer hydrophobes. SDS has the most profound influence on Quatrisoft interfacial behavior due to the changes in electrostatics accompanying formation of the polymer/surfactant complex. In the case of C₁₂E₅, large surfactant clusters bound to the polymer affect the macromolecules' conformation in the adsorbed layer via steric effects. In contrast to SDS and C₁₂E₅, no evidence of interaction between the polycation and a like-charged surfactant, TTAB, was obtained. At the same time, TTAB adsorbs on the surface in competition with the polyelectrolyte. This results in partial displacement of the latter and its looser attachment to the surface.     

两相催化体系中烯烃氢甲酰化的高区域选择性

采用水溶性铑膦配合物催化剂在两相(水/有机物)体系中进行长链烯烃氢甲酰化反应合成高碳醛,具有反应条件缓和、催化剂与产物容易分离的优点,而且用水作溶剂既便宜、又安全,有利于环境保护,因此引起国内外化学家重视,进行了大量研究[1,2].     

Semi‐interpenetrating polymer networks composed of poly(N‐isopropyl acrylamide) and polyacrylamide hydrogels

Three series of semi‐interpenetrating polymer networks, based on crosslinked poly(N‐isopropyl acrylamide) (PNIPA) and 1 wt % nonionic or ionic (cationic and anionic) linear polyacrylamide (PAAm), were synthesized to improve the mechanical properties of PNIPA gels. The effect of the incorporation of linear polymers into responsive networks on the temperature‐induced transition, swelling behavior, and mechanical properties was studied. Polymer networks with four different crosslinking densities were prepared with various molar ratios (25:1 to 100:1) of the monomer (N‐isopropyl acrylamide) to the crosslinker (methylenebisacrylamide). The hydrogels were characterized by the determination of the equilibrium degree of swelling at 25 °C, the compression modulus, and the effective crosslinking density, as well as the ultimate hydrogel properties, such as the tensile strength and elongation at break. The introduction of cationic and anionic linear hydrophilic PAAm into PNIPA networks increased the rate of swelling, whereas the presence of nonionic PAAm diminished it. Transition temperatures were significantly affected by both the crosslinking density and the presence of linear PAAm in the hydrogel networks. Although anionic PAAm had the greatest influence on increasing the transition temperature, the presence of nonionic PAAm caused the highest dimensional change. Semi‐interpenetrating polymer networks reinforced with cationic and nonionic PAAm exhibited higher tensile strengths and elongations at break than PNIPA hydrogels, whereas the presence of anionic PAAm caused a reduction in the mechanical properties. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 3987–3999, 2004     

Effect of Surfactants on the Formation,Morphology, and Surface Property of Synthesized SiO2 Nanoparticles

Abstract

This study investigated the effect of cationic, anionic (saturated and unsaturated), and nonionic surfactants on the formation, morphology, and surface properties of silica nanoparticles synthesized by the ammonium‐catalyzed hydrolysis of tetraethoxysilane in alcoholic media. Results indicate that at a relatively low surfactant concentration (1 × 10^?3–1 × 10^?6 M), cationic surfactants significantly affected the growth of silica particles as measured by dynamic light scattering and transmission electron microscopic analyses. In contrast, the anionic and nonionic surfactants showed relatively minor effects in the low concentration range. The magnitude of negative zeta potential was reduced for silica colloids that were synthesized in the presence of cationic surfactant because of charge neutralization. The presence of anionic surfactants only slightly increased the negative zeta potential while the nonionic surfactant showed no obvious effects. At high surfactant concentrations (>1 × 10^?3 M), cationic and anionic surfactants both induced colloid aggregation, while the nonionic surfactant showed no effect on particle size. Raman spectroscopic analysis suggests that molecules of cationic surfactants adsorb on silica surfaces via head groups, aided by favorable electrostatic attraction, while molecules of anionic and nonionic surfactants adsorb via their hydrophobic tails.     

Interaction of the anionic surfactant SDS with a cellulose thin film and the role of electrolyte and poyelectrolyte. 2 Hydrophilic cellulose

The interaction of the anionic surfactant, sodium dodecylsulfate (SDS), with the hydrophilic surface of a thin cellulose film and the role of electrolyte (0.1 M NaCl) and the polyelectrolyte, poly(dimethyldiallyl ammonium chloride) [polydmdaac], have been studied by neutron reflectivity (NR). The thin cellulose films were prepared by Langmuir-Blodgett (LB) deposition of trimethylsilyl-cellulose (TMSC) on silicon, and the hydrophilic surface was produced by the cleaving of the terminal methyl groups of the TMSC by HCl vapor. Despite both the surfactant and cellulose surfaces being nominally anionic, SDS adsorption and swelling of the cellulose film occurred during adsorption. The results show that the nature of the adsorption and the extent of the penetration into the cellulose film can be controlled by the addition of electrolyte, NaCl, and cationic polyelectrolyte, polydmdaac.     

Surfactant aggregation within room-temperature ionic liquid 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide

On the basis of the response of solvatochromic probes [Reichardt's betaine dye, pyrene, and 1,3-bis(1-pyrenyl)propane], we have investigated the aggregation behavior of common anionic, cationic, and nonionic surfactants when solubilized within a low-viscosity room-temperature ionic liquid 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide (emimTf2N). We observed possible aggregate formation by all nonionic surfactants included in the study (Brij-35, Brij-700, Tween-20, and Triton X-100), while no aggregation was observed for the cationic surfactant cetyltrimethylammonium bromide. The anionic surfactant sodium dodecyl sulfate does not appear to solubilize within emimTf2N at ambient conditions.     

Hollow nanoparticles prepared from pH‐responsive template polymer micelles

Water‐soluble crosslinked hollow nanoparticles were prepared using pH‐responsive anionic polymer micelles as templates. The template micelles were formed from pH‐responsive diblock copolymers (PAMPS‐PAaH) composed of the poly(sodium 2‐(acrylamido)‐2‐methylpropanesulfonate) and poly(6‐(acrylamido)hexanoic acid) blocks in an aqueous acidic solution. The PAMPS and PAaH blocks form a hydrophilic anionic shell and hydrophobic core of the core‐shell polymer micelle, respectively. A cationic diblock copolymer (PEG‐P(APTAC/CEA)) with the poly(ethylene glycol) block and random copolymer block composed of poly((3‐acrylamidopropyl)trimethylammonium chloride) containing a small amount of the 2‐(cinnamoyl)ethylacrylate photo‐crosslinkable unit can be adsorbed to the anionic shell of the template micelle due to electrostatic interaction, which form a core‐shell‐corona three‐layered micelle. The shell of the core‐shell‐corona micelle is formed from a polyion complex with anionic PAMPS and cationic P(APTAC/CEA) chains. The P(APTAC/CEA) chains in the shell of the core‐shell‐corona micelle can be photo‐crosslinked with UV irradiation. The template micelle can be dissociated using NaOH, because the PAaH blocks are ionized. Furthermore, electrostatic interactions between PAMPS and PAPTAC in the shell are screened by adding excess NaCl in water. The template micelles can be completely removed by dialysis against water containing NaOH and NaCl to prepare the crosslinked hollow nanoparticles. Transmission electron microscopy observations confirmed the hollow structure. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012