Ni控制掺杂TiO2薄膜的光电化学及光催化活性

采用溶胶-凝胶法通过分步控制工艺制备了镍离子不同掺杂方式的TiO₂薄膜。通过甲基橙的光催化降解动力学来表征其光催化活性。结果表明：镍离子非均匀掺杂在掺杂量0.5%时可以明显增强TiO₂的光催化活性，而均匀掺杂提高TiO₂的光催化活性较小。光电化学表征结果显示：镍离子非均匀掺杂TiO₂薄膜的瞬时光电流信号较强，说明其光生载流子易于生成且分离效果较好；循环伏安曲线表明，光照时Ni非均匀掺杂的TiO₂薄膜改变了体系的氧化还原电位，说明了薄膜内建电场的建立。基于半导体的P-N结原理探讨了镍离子非均匀掺杂TiO₂薄膜的光催化活性机理。     

铂非均匀掺杂二氧化钛薄膜的光催化性能

采用溶胶-凝胶法制备了铂非均匀掺杂的二氧化钛薄膜, 并用UV-vis分光光度计及电化学工作站表征了薄膜的光吸收性能和光电化学行为, 通过对甲基橙的光催化降解动力学来表征催化剂的光催化活性. 结果表明 Pt非均匀掺杂可以明显增强二氧化钛的光催化活性, 而均匀掺杂的效果较差; Pt非均匀掺杂的最佳量为0.3 mol%. 催化剂薄膜的电化学行为显示: Pt非均匀掺杂二氧化钛薄膜的开路电压高, 交流阻抗小. 并从半导体的PN结原理探讨了Pt非均匀掺杂二氧化钛的催化活性机理.     

Preparation and Characterization of Bismuth Doped TiO2 Thin Films

A series of Bismuth-doped titanium oxide (Bi-doped TiO₂) thin films on glass substrates have been prepared by sol-gel dip coating process. The prepared catalysts were characterized by XRD and XPS. The photocatlytic activity of the thin film catalysts was evaluated through the photodegradation of aqueous methyl orange under UV illumination. The experiments demonstrated that the Bi-doped TiO₂ prepared was anatase phase. The doped bismuth was in the 3⁺ oxidation state. The presence of Bi significantly enhanced the photocatalytic activity of TiO₂ films. At calcination temperature of 500°C, with doping concentration of 2 wt %, Bi-doped TiO₂ thin film showed the highest photocatalyic activity.     

锰离子控制掺杂二氧化钛薄膜光催化活性增强的机理探讨

采用溶胶-凝胶法通过工艺控制制备了锰离子以不同形式掺杂TiO₂的光催化剂薄膜,并通过XPS和SEM对薄膜的结构进行表征.通过UV-Vis分光光度计及电化学工作站表征了薄膜的光吸收性能和光电化学性能,通过甲基橙溶液的光催化降解脱色率来表征催化剂薄膜的光催化活性.结果表明,以锰离子MT掺杂方式制备的TiO₂薄膜可明显增强TiO₂的光催化活性,而以MM掺杂方式制备的TiO₂薄膜反而降低了TiO₂的光催化活性;锰离子MT掺杂方式的最佳掺杂质量分数为0.8%.催化剂薄膜的电化学行为显示,薄膜具有p-n结的电容-电压特性,锰离子MT掺杂TiO₂薄膜的开路电位和瞬时光电流信号较强,说明其光生载流子易于生成并且分离效果较好.依据半导体的p-n结原理探讨了锰离子控制掺杂TiO₂的光催化活性机理.     

Comparison of optical and structural properties of nanostructure TiO2 thin film doped by Sn and Nb

The thin films of TiO₂ doped by Sn or Nb were prepared by sol–gel method under process control. The effects of Sn and Nb doping on the structural, optical and photo-catalytic properties of applied thin films have been studied by X-ray diffraction (XRD) high resolution transmission electron microscopy and UV–Vis absorption spectroscopy. Surface chemical state of thin films was examined by atomic X-ray photoelectron spectroscopy. XRD results suggest that adding impurities has a great effect on the crystallinity and particle size of TiO₂. Titania rutile phase formation in thin film was promoted by Sn⁴⁺ addition but was inhibited by Nb⁵⁺ doping. The activity of the photocatalyst was evaluated by photocatalytic degradation kinetics of aqueous methylene blue under UV and Visible radiation. The results show that the photocatalytic activity of the Sn-doped TiO₂ thin film have a larger degradation efficiency than Nb-doped TiO₂ under visible light, but under UV light photocatalytic activity of the Nb-doped TiO₂ thin film is better.     

Synthesis and characterization of novel InVO<Subscript>4</Subscript>–TiO<Subscript>2</Subscript> thin films using the low temperature sol

The InVO₄ sol was obtained by a mild hydrothermal treatment (the precursor precipitation solution at 423 K, for 4 h). Novel visible-light activated photocatalytic InVO₄–TiO₂ thin films were synthesized through a sol–gel dipping method from the composite sol, which was obtained by mixing the low temperature InVO₄ sol and TiO₂ sol. The photocatalytic activities of the new InVO₄–TiO₂ thin films under visible light irradiation were investigated by the photocatalytic discoloration of methyl orange aqueous solution. The thin films were characterized by X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM) and UV–Vis absorption spectroscopy (UV–Vis). The results revealed that the InVO₄ doped thin films enhanced the methyl orange degradation rate under visible light irradiation, 3.0 wt% InVO₄–TiO₂ thin films reaching 80.1% after irradiated for 15 h.     

Studies on photocatalytic activity of Ag/TiO2 films

Ag/TiO₂ photocatalytic films were produced by hybrid sol-gel method. The photocatalytic degradation of methyl orange (MO) in aqueous solution under 365 nm irradiation on TiO₂ and Ag/TiO₂ thin films was investigated. The state and amount of Ag species within the film and the enhancement mechanism of photocatalytic activity of Ag/TiO₂ were discussed. With a loading molar ratio of Ag/Ti = 0.135 in TiO₂ film, the maximum catalytic efficiency was observed. __________ Translated from Journal of Beijing Normal University (Natural Sciences), 2005, 41(6) (in Chinese)     

Effects of doping La and Cu on photoinduced charge properties of TiO2 and its relationships with photocatalytic activity

The pure, 1 mol% only La or only Cu doped TiO₂ and La and Cu codoped TiO₂ were prepared by a sol-gel process. The effects of doping on photoinduced charge properties of nanosized TiO₂ were mainly investigated by means of Surface Photovoltage Spectrum (SPS) and Photoluminescence Spectrum (PL), together with their relationships with photocatalytic activity. The results show that La dopant can inhibit the phase transformation of TiO₂, meanwhile improve the separation rate of photoinduced charge carriers, and enrich the binding surface states. However, Cu dopant has a reverse effect compared to La dopant. This is responsible for the results that doping La is favorable for the increase in the photocatalytic activity for degrading the RhB solution, while doping Cu is bad to photocatalyitc reaction. In addition, codoping La and Cu cannot exhibit an obvious combination effect.     

The influence of precursor’s composition and concentration on cadmium doped TiO<Subscript>2</Subscript> film

The purpose of this article is to emphasize that new nanomaterials offer a number of attractive alternatives for solar energy use in wastewater photocatalysis. The wastewater from the textile industry contains dyes and heavy metals. Thin films of cadmium doped TiO₂ (Cd-TiO₂) were coated by a doctor blade using TiO₂ Degussa P25 and cadmium precursor (cadmium nitrate). The photocatalytic efficiency of cadmium doped TiO₂ is strongly influenced by crystal structure, particle size, particle morphology, porosity and doping. The pore size distribution and the roughness analysis have been studied by the atomic force microscopy (AFM) of the thin films. The photocatalytic activity of the samples was tested in Methyl orange and Methylene blue photodegradation. Cadmium doped TiO₂ catalyst does not significantly decrease the efficiency of photodegradation processes, and, in some situations, improves dye photodegradation.     

The preparation and characterization of La doped TiO2 nanoparticles and their photocatalytic activity

In this paper, pure and La doped TiO₂ nanoparticles with different La content were prepared by a sol-gel process using Ti (OC₄H₉)₄ as raw material, and also were characterized by XRD, TG-DTA, TEM, XPS, DRS and Photoluminescence (PL) spectra. We mainly investigated the effects of calcining temperature and La content on the properties and the photocatalytic activity for degrading phenol of as-prepared TiO₂ samples, and also discussed the relationships between PL spectra and photocatalytic activity as well as the mechanisms of La doping on TiO₂ phase transformation. The results showed that La³⁺ did not enter into the crystal lattices of TiO₂ and was uniformly dispersed onto TiO₂ as the form of La₂O₃ particles with small size, which possibly made La dopant have a great inhibition on TiO₂ phase transformation; La dopant did not give rise to a new PL signal, but it could improve the intensity of PL spectra with a appropriate La content, which was possibly attributed to the increase in the content of surface oxygen vacancies and defects after doping La; La doped TiO₂ nanoparticles calcined at 600°C exhibited higher photocatalytic activity, indicating that 600°C was an appropriate calcination temperature. The order of photocatalytic activity of La doped TiO₂ samples with different La content was as following: 1>1.5>3>0.5>5>0 mol%, which was the same as the order of their PL intensity, namely, the stronger the PL intensity, the higher the photocatalytic activity, demonstrating that there were certain relationships between PL spectra and photocatalytic activity. This could be explained by the points that PL spectra mainly resulted from surface oxygen vacancies and defects during the process of PL, while surface oxygen vacancies and defects could be favorable in capturing the photoinduced electrons during the process of photocatalytic reactions.     

Direct View of Cr Atoms Doped in Anatase TiO2(001) Thin Film

Imaging the doping elements is critical for understanding the photocatalytic activity of doped TiO₂ thin film. But it is still a challenge to characterize the interactions between the dopants and the TiO₂ lattice at the atomic level. Here, we use high angle annular dark-field/annular bright-field scanning transmission electron microscope (HAADF/ABF-STEM) combined with electron energy loss spectroscopy (EELS) to directly image the individual Cr atoms doped in anatase TiO₂(001) thin film from [100] direction. The Cr dopants, which are clearly imaged through the atomic-resolution EELS mappings while can not be seen by HADDF/ABF-STEM, occupy both the substitutional sites of Ti atoms and the interstitial sites of TiO₂ matrix. Most of them preferentially locate at the substitutional sites of Ti atoms. These results provide the direct evidence for the doping structure of Cr-doped A-TiO₂ thin film at the atomic level and also prove the EELS mapping is an excellent technique for characterizing the doped materials.     

Sol-gel preparation and characterization of Co/TiO<Subscript>2</Subscript> nanoparticles: Application to the degradation of methyl orange

Cobalt doped titania nanoparticles were synthesized by sol-gel method using titanium(IV) isopropoxide and cobalt nitrate as precursors. X-Ray diffraction (XRD) results showed that titania and Co/TiO₂ nanoparticles only include anatase phase. The framework substitution of Co in TiO₂ nanoparticles was established by XRD, scanning electron microscopy equipped with energy dispersive X-ray microanalysis (SEM-EDX) and Fourier transform infrared (FT-IR) techniques. Transmission electron microscopy (TEM) images confirmed the nanocrystalline nature of Co/TiO₂. The increase of cobalt doping enhanced “red-shift” in the UV-Vis absorption spectra. The dopant suppresses the growth of TiO₂ grains, agglomerates them and shifts the band absorption of TiO₂ from ultraviolet (UV) to visible region. The photocatalytic activity of samples was tested for degradation of methyl orange (MO) solutions. Although the photocatalytic activity of undoped TiO₂ was found to be higher than that of Co/TiO₂ under UV irradiation, the presence of 0.5% Co dopant in TiO₂ resulted in a catalyst with the highest activity under visible irradiation.     

钌配合物敏化La3+掺杂纳米多孔TiO2电极的光电性能研究

在染料敏化太阳能电池中,TiO2膜和敏化剂决定着电池的总体效率和机械性能。本文以4-甲基吡啶为原料,经过偶联、氧化、配位和配体交换反应合成了cis-RuL2(SCN)2, (L=2,2’-联吡啶-4,4’-二羧酸),通过溶胶-凝胶法制备了TiO2膜。为了提高TiO2膜的光电性能,将不同浓度的La(NO3)3 (0.1%、0.3%、0.5%和0.7%) 加入到溶胶中,采用cis-RuL2(SCN)2将掺杂前后的TiO2膜进行敏化。利用X射线衍射仪、原子力显微镜和X射线光电子能谱对所得薄膜进行结构表征。结果表明,当La离子的浓度为0.5%时,太阳能电池的效率最高,短路电流和开路电压比未掺杂的分别提高了0.54 mA/cm2和30.41 mV。     

Zr离子掺杂TiO2可见光催化剂光催化活性的研究

本文采用溶胶-凝胶法制备了Zr离子掺杂TiO₂光催化剂。光催化降解对氯苯酚实验表明,Zr离子掺杂浓度为10%时活性最高,其紫外光、可见光催化活性分别是纯TiO₂的1.5倍和4倍。利用XRD、Raman、XPS、UV-Vis DRS、PL等技术对样品进行了表征,结果表明：Zr离子以取代式掺杂方式进入TiO₂晶格,在TiO₂导带下方形成掺杂能级,增强了可见光响应,促进了光生载流子的分离,此外Zr离子掺杂在催化剂表面引入大量表面缺陷,增加了表面羟基物种,从而使得Zr离子掺杂TiO₂光催化剂的紫外、可见光催化活性显著提高。     

Surface properties and photocatalytic activity of nanocrystalline titania films

In this work the efficiency and physicochemical details of a thin film produced by help of a microwave assisted sol gel technique is compared to different commercial powders (Degussa P25 and Hombikat UV100) deposited on glass substrates. Furthermore, a supercritical produced TiO₂ powder (SC 134) was included in the comparison.The prepared TiO₂ films were characterized using XRD, XPS, AFM, DSC and DLS. The photocatalytic activity was determined using stearic acid as a model compound. Investigation of the prepared films showed that the Degussa P25 film and the sol–gel film were the most photocatalytic active films. The activity of the films was found to be related to the crystallinity of the TiO₂ film and the amount of surface area and surface hydroxyl groups. Based on the XPS investigation of the films before and after UV irradiation it was suggested that the photocatalytic destruction of organic matter on TiO₂ films proceeds partly through formation of hydroxyl radicals which are formed from surface hydroxyl groups created by interactions between adsorbed water and vacancies on the TiO₂ surface. Furthermore a correlation between the amount of OH groups on the surface of the different TiO₂ films and the photocatalytic activity was found.     

Preparation and characterization of silver and indium vanadate co-doped TiO2 thin films as visible-light-activated photocatalyst

Novel visible-light-activated photocatalytic Ag/InVO₄-TiO₂ thin films were developed in this paper through a sol-gel method from the TiO₂ sol containing Ag and InVO₄. The photocatalytic activities of Ag/InVO₄-TiO₂ thin films were investigated based on the oxidation decomposition of methyl orange in aqueous solution. The Ag/InVO₄-TiO₂ thin films were characterized by X-Ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), X-ray photoelectron spectroscopy (XPS) and UV-vis absorption spectroscopy (UV-vis). The results revealed that the Ag/InVO₄-TiO₂ thin films extended the light absorption spectrum toward the visible region; the Ag and InVO₄ co-doped thin films significantly enhanced the methyl orange photodegradation under visible light irradiation. It has been confirmed that the Ag/InVO₄-TiO₂ thin films could be excited by visible light (E < 3.2 eV). The significant enhancement in the Ag/InVO₄-TiO₂ photo activity under visible light irradiation can be ascribed to the simultaneous effects of doped noble metal Ag by acting as electron traps and InVO₄ as narrow band gap sensitizer.     

Ce(4+) doped TiO<Subscript>2</Subscript> thin films: Characterization and photocatalysis

Undoped and Ce(4+) doped TiO₂ thin films were prepared by sol-gel method. The samples were characterized using scanning electron microscopy, the photocatalytic reactivity was evaluated by degradation of methylene blue in the aqueous solution. 0.5 wt. % Ce(4+) doped TiO₂ thin films calcined at 400°C show the highest photocatalytic activity. The text was submitted by the authors in English.     

Sol–gel preparation of pure and doped TiO2 films for the photocatalytic oxidation of ethanol in air

Stable sols of TiO₂ were synthesized by a non-aqueous sol–gel process using titanium (IV) isopropoxide as precursor. The microstructure, optical and morphological properties of the films obtained by spin-coating from the sol, and annealed at different temperatures, were investigated using scanning electron microscopy, transmission electron microscopy, diffuse reflectance spectroscopy and ellipsometry. The crystalline structure of the films was characterized by X-ray diffraction and their photocatalytic activity was evaluated for the oxidation of ethanol in air. The influence of the calcination temperature, pre-heat treatment and the number of layers was studied. Simultaneous thermo-gravimetric and differential thermal analysis measurements were carried out to ascertain the thermal decomposition behavior of the precursors. In order to obtain a higher photoresponse in the visible region, a series of vanadium-, niobium- and tantalum-doped TiO₂ catalysts was synthesized by the same sol–gel method. For V doping two different precursors, a vanadium alkoxide and V₂O₅, were used. The effect on the crystallization and photocatalytic activity of the doped TiO₂ films was investigated. Furthermore, to identify the effective composition of the samples, they were characterized by X-ray photoelectron spectroscopy and the surface area of the powders was measured by N₂ adsorption. The 10 wt.% doped catalysts exhibit high photocatalytic activity under visible light and among them the best performance was obtained for the sample containing Ta as dopant. The crystallite sizes are closely related to the photocatalytic activity.     

Low-temperature synthesis of photocatalytic TiO2 thin film from aqueous anatase precursor sols

Anatase TiO₂ sols (RS) were synthesized by peptizing the hydrolysis of titanyl sulfate in abundant hydrogen peroxide solution and subsequent reflux to enhance crystallization. The influences of various reflux time on crystallinity, morphology, and size of the obtained TiO₂ sol and dried TiO₂ film particles were investigated. At room temperature, crystalline TiO₂ thin film was deposited on glass silde from the as prepared TiO₂ sol by dip-coating method. No further thermal posttreatment was required to eliminate organics from the film or to induce titania crystallization. TiO₂ thin film on substrates could be thickened by means of consecutive dip-coating process. Titania film thus obtained was transparent and showed proper adherence. The photocatalytic activities of the TiO₂ thin film was assessed by the degradation of methyl orange in aqueous solution. The preparation process of photocatalytic TiO₂ thin film was quite simple and a low-temperature route.     

Photocatalytic Degradation of Glyphosate in Water by N‐Doped SnO2/TiO2 Thin‐Film‐Coated Glass Fibers

Photocatalytic degradation of glyphosate contaminated in water was investigated. The N‐doped SnO₂/TiO₂ films were prepared via sol–gel method, and coated on glass fibers by dipping method. The effects of nitrogen doping on coating morphology, physical properties and glyphosate degradation rates were experimentally determined. Main variable was the concentration of nitrogen doping in range 0–40 mol%. Nitrogen doping results in shifting the absorption wavelengths and narrowing the band gap energy those lead to enhancement of photocatalytic performance. The near optimal 20N/SnO₂/TiO₂ composite thin film exhibited about two‐ and four‐folds of glyphosate degradation rates compared to the undoped SnO₂/TiO₂ and TiO₂ films when photocatalytic treatment were performed under UV and solar irradiations, respectively, due to its narrowest band gap energy (optical absorption wavelength shifting to visible light region) and smallest crystallite size influenced by N‐doping.