Si-nanostructures formation in amorphous silicon nitride SiNx:H deposited by remote PECVD

The formation of silicon nanoclusters embedded in amorphous silicon nitride (SiN_x:H) can be of great interest for optoelectronic devices such as solar cells. Here amorphous SiN_x:H layers have been deposited by remote microwave-assisted chemical vapor deposition at 300 °C substrate temperature and with different ammonia [NH₃]/silane [SiH₄] gas flow ratios (R=0.5−5). Post-thermal annealing was carried out at 700 °C during 30 min to form the silicon nanoclusters. The composition of the layers was determined by Rutherford back scattering (RBS) and elastic recoil detection analysis (ERDA). Fourier transform infrared spectroscopy (FTIR) showed that the densities of SiH (2160 cm⁻¹) and NH (3330 cm⁻¹) molecules are reduced after thermal annealing for SiN:H films deposited at flow gas ratio R>1.5. Breaking the SiH bonding provide Si atoms in excess in the bulk of the layer, which can nucleate and form Si nanostructures. The analysis of the photoluminescence (PL) spectra for different stoichiometric layers showed a strong dependence of the peak characteristics (position, intensity, etc.) on the gas flow ratio. On the other hand, transmission electron microscopy (TEM) analysis proves the presence of silicon nanoclusters embedded in the films deposited at a gas flow ratio of R=2 and annealed at 700 °C (30 min).     

Photoluminescence and optical absorption properties of silicon quantum dots embedded in Si-rich silicon nitride matrices

Silicon nitride (SiN_x) films were prepared with a gas mixture of SiH₄ and NH₃ on Si wafers using the plasma-enhanced chemical vapor deposition (PECVD) method. High-resolution transmission electron microscopy and infrared absorption have been used to reveal the existence of the Si quantum dots (Si QDs) and to determine the chemical composition of the silicon nitride layers. The optical properties of these structures were studied by photoluminescence (PL) spectroscopy and indicate that emission mechanisms are dominated by confined excitons within Si QDs. The peak position of PL could be controlled in the wavelength range from 1.5 to 2.2 eV by adjusting the flow rates of ammonia and silane gases. Absorbance spectra obtained in the transmission mode reveal optical absorption from Si QDs, which is in good correlation with PL properties. These results have implications for future nanomaterial deposition controlling and device applications.     

Influence of the temperature on the photoluminescence of silicon clusters embedded in a silicon oxide matrix

Amorphous silicon oxide thin films were prepared by co-evaporation of Si and SiO in ultra-high vacuum. Different compositions were obtained by changing the evaporation rate of silicon. After thermal annealing treatments, the dissociation of the silicon oxide in pure silicon and silicon dioxide leads to the formation of silicon clusters embedded in a silicon oxide matrix. Thus the samples were annealed to different temperatures up to 950°C. Depending on the annealing temperature and on the composition, different cluster sizes were obtained. The photoluminescence (PL) energy depends on the cluster size and a large range of wavelengths is obtained from 500 to 750 nm. The PL, attributed to a confinement effect of the electron–hole pairs in the silicon particles, is studied as a function of the temperature. It is demonstrated that the continuous decrease of PL intensity with the temperature from 77 to 500 K depends on the structure of the samples. For samples with well-separated clusters, the PL decreases rapidly with the temperature. For samples containing clusters separated by a small distance, the PL weakly depends on the temperature. No shift of the energy is observed. The results are discussed by taking into account the competition between the radiative recombination in the silicon clusters and the non-radiative escape of the carriers via a hopping mechanism.     

Photoluminescence analyses of hydrogenated amorphous silicon nitride thin films

Silicon-rich hydrogenated amorphous silicon nitride (a-SiN_x:H) films were grown by plasma enhanced chemical vapor deposition (PECVD) with different r=NH₃/SiH₄ gas flow ratios. The optical absorption characteristics were analyzed by Fourier transform infrared (FTIR) and UV-visible transmittance spectroscopies. The recombination properties were investigated via photoluminescence (PL) measurements. As r was increased from 2 to 9, the PL emission color could be adjusted from red to blue with the emission intensity high enough to be perceived by naked eye at room temperature. The behaviors of the PL peak energy and the PL band broadness with respect to the optical constants were discussed in the frame of electron-phonon coupling and band tail recombination models. A semiquantitative analysis supported the band tail recombination model, where the recombination was found to be favored when the carriers thermalize to an energy level at which the band tail density of states (DOS) reduces to some fraction of the relevant band edge DOS. For the PL efficiency comparison of the samples with different nitrogen contents, the PL intensity was corrected for the absorbed intensity fraction of the incident PL excitation source. The resulted correlation between the PL efficiency and the subgap absorption tail width further supported the band tail recombination model.     

Study of structural and electronic environments of hydrogenated amorphous silicon carbonitride (a-SiCN:H) films deposited by hot wire chemical vapor deposition

Hydrogenated amorphous silicon carbon nitride (a-SiCN:H) thin films were deposited by hot wire chemical vapor deposition (HWCVD) using SiH₄, CH₄, NH₃ and H₂ as precursors. The effects of the H₂ dilution on structural and chemical bonding of a-SiCN:H has been investigated by Raman and X-ray photoelectron spectroscopy (XPS). Increasing the H₂ flow rate in the precursor gas more carbon is introduced into the a-SiCN:H network resulting in decrease of silicon content in the film from 41 at.% to 28.8 at.% and sp² carbon cluster increases when H₂ flow rate is increased from 0 to 20 sccm.     

Effect of thermal annealing on the formation of silicon nanoclusters in SiOX films grown by PLD

Silicon nanoclusters formation in pulsed laser deposited (PLD) silicon suboxide (SiO_X) films by thermal annealing is reported. The SiO_X films are prepared by ablation of silicon target at different oxygen partial pressures. The different deposition conditions are employed to study the effect of oxygen concentration on the size of the nanoclusters. Post deposition thermal annealing of the films leads to the phase separation in silicon suboxide films. Fourier transform infrared spectroscopy, micro-Raman spectroscopy and UV-vis absorption spectroscopy studies were carried out to characterize the formation of silicon nanoclusters in SiO_X films.     

Structural and photo-luminescence properties of nanocrystalline silicon films deposited at low temperature by plasma-enhanced chemical vapor deposition

Nanocrystalline silicon (nc-Si) films were prepared by a plasma-enhanced chemical vapor deposition method at a deposition temperature below 220 °C with different dynamic pressures (P_g), hydrogen flow rates ([H₂]), and RF powers, using SiH₄/H₂/SiF₄ mixtures. We examined the photo-luminescence (PL) spectra and the structural properties. We observed two stronger and weaker PL spectra with a peak energies around E_PL = 1.8 and 2.2-2.3 eV, respectively, suggesting that the first band was related to nanostructure in the films, and another band was associated with SiO-related bonds. The nc-Si films with rather large PL intensity was obtained for high [H₂] and/or low pressure values, However, effects of [H₂] are likely to be different from those of P_g. The average grain size (δ) and the crystalline volume fraction (ρ) at first rapidly increase, and then slowly increase, with increasing P_g. Other parameters exhibited opposite behaviors from those of δ or ρ. These results were discussed in connection with the changes in the PL properties with varying the deposition conditions.     

Excitonic photoluminescence characteristics of amorphous silicon nanoparticles embedded in silicon nitride film

We have investigated the photoluminescence (PL) properties of amorphous silicon nanoparticles (a-Si NPs) embedded in silicon nitride film (Si-in-SiN_x) grown by helicon wave plasma-enhanced chemical vapor deposition (HWP-CVD) technique. The PL spectrum of the film exhibits a broad band constituted of two Gaussian components. From photoluminescence excitation (PLE) measurements, it is elucidated that the two PL bands are associated with the a-Si NPs and the silicon nitride matrix surrounding a-Si NPs, respectively. The existence of Stokes shift between PL and absorption edge indicates that radiative recombination of carriers occurs in the states at the surface of the Si NPs, whereas their generation takes place in the a-Si NPs cores and the silicon nitride matrix, respectively. The visible PL of the film originates from the radiative recombination of excitons trapped in the surface states. At decreasing excitation energy (E_ex), the PL peak energy was found to be redshifted, accompanied by a narrowing of the bandwidth. These results are explained by surface exciton recombination model taking into account there existing a size distribution of a-Si NPs in the silicon nitride matrix.     

Photoluminescence from Er-doped silicon rich oxide thin films

 Photoluminescence (PL) properties of Er-doped silicon rich oxide thin films deposited on Si substrate by co-evaporation of silicon monoxide and Er under different atmospheres are investigated. The samples exhibit luminescence peak at 1.54 μm which could be assigned to the recombination in intra-4f Er³⁺ transition. PL shows that this transition is highest when ammonia atmosphere is used during deposition followed by an annealing temperature at 850 °C in 95% N₂+5% H₂ gas (forming gas). In fact, we believe that the presence of the N atoms around Er ions increases the intensity of the 1.54 μm luminescence.     

Enhancement of the photoluminescence of silicon nanocrystals under the influence of electric field

The effect of electric field generated by the application of surface acoustic waves on photoluminescence (PL) of silicon nanocrystals embedded in SiO₂ films is studied. It is shown that the application of electric field results in an increase in the intensity of nanocrystal PL, the increase amounting to 10% at a field amplitude of 6 kV cm⁻¹. The results are discussed within the frame of the self-trapped exciton model.     

Investigation on preparation and physical properties of nanocrystalline Si/SiO2 superlattices for Si-based light-emitting devices

Structures containing silicon nanocrystals (nc-Si) are very promising for Si-based light-emitting devices. Using a technology compatible with that of silicon, a broader wavelength range of the emitted photoluminescence (PL) was obtained with nc-Si/SiO₂ multilayer structures. The main characteristic of these structures is that both layers are light emitters. In this study we report results on a series of nc-Si/SiO₂ multilayer periods deposited on 200 nm thermal oxide SiO₂/Si substrate. Each period contains around 10 nm silicon thin films obtained by low-pressure chemical vapour deposition at T=625°C and 100 nmSiO₂ obtained by atmospheric pressure chemical vapour deposition T=400°C. Optical and microstructural properties of the multilayer structures have been studied by spectroscopic ellipsometry (using the Bruggemann effective medium approximation model for multilayer and multicomponent films), FTIR and UV–visible reflectance spectroscopy. IR spectroscopy revealed the presence of SiO_x structural entities in each nc-Si/SiO₂ interface. Investigation of the PL spectra (using continuous wave-CW 325 nm and pulsed 266 nm laser excitation) has shown several peaks at 1.7, 2, 2.3, 2.7, 3.2 and 3.7 eV, associated with the PL centres in SiO₂, nc-Si and Si–SiO₂ interface. Their contribution to the PL spectra depends on the number of layers in the stack.     

Investigation of the dependence of the photoluminescence properties of silicon nanoclusters on their volume fraction in a silicon oxide matrix

The photoluminescence (PL) spectra and kinetics of amorphous and crystalline silicon nanoclusters are investigated. The given nanoclusters are formed by thermal annealing of thin suboxide silicon films with different volume fractions of silicon. It is demonstrated that the PL intensity and lifetime of the ensembles of silicon nanocrystals have a steplike dependence on the silicon volume fraction in the film. The influence of the percolation effect on the photoluminescence properties of the structures under study is discussed.     

Chemical and phase compositions of silicon oxide films with nanocrystals prepared by carbon ion implantation

The chemical and phase compositions of silicon oxide films with self-assembled nanoclusters prepared by ion implantation of carbon into SiO _x (x < 2) suboxide films with subsequent annealing in a nitrogen atmosphere have been investigated using X-ray photoelectron spectroscopy in combination with depth profiling by ion sputtering. It has been found that the relative concentration of oxygen in the maximum of the distribution of implanted carbon atoms is decreased, whereas the relative concentration of silicon remains almost identical over the depth in the layer containing the implanted carbon. The in-depth distributions of carbon and silicon in different chemical states have been determined. In the regions adjacent to the layer with a maximum carbon content, the annealing results in the formation of silicon oxide layers, which are close in composition to SiO₂ and contain silicon nanocrystals, whereas the implanted layer, in addition to the SiO₂ phase, contains silicon oxide species Si²⁺ and Si³⁺ with stoichiometric formulas SiO and Si₂O₃, respectively. The film contains carbon in the form of SiC and elemental carbon phases. The lower limit of the average size of silicon nanoclusters has been estimated as ∼2 nm. The photoluminescence spectra of the films have been interpreted using the obtained results.     

Structural and photoluminescence properties of Si nanoclusters obtained by ion implantation into Si3N4 films

In the present paper we report structural and photoluminescence (PL) results from samples obtained by Si implantation into stoichiometric silicon nitride (Si₃N₄) films. The Si excess was introduced in the matrix by 170 keV Si implantation performed at different temperatures with a fluence of Φ=1×10¹⁷ Si/cm². The annealing temperature was varied between 350 and 900 °C in order to form the Si precipitates. PL measurements, with a 488 nm Ar laser as an excitation source, show two superimposed broad PL bands centered around 760 and 900 nm. The maximum PL yield is achieved for the samples annealed at 475 °C. Transmission electron microscopy (TEM) measurements show the formation of amorphous nanoclusters and their evolution with the annealing temperature.     

Effect of DC bias on microstructural rearrangement of a-SiN:H films on PET substrate

Hydrogenated amorphous silicon nitride (a-SiN:H) films were deposited on flexible polyethylene terephthalate substrates at temperature as low as 100 °C by hot-wire chemical vapor deposition using SiH₄, H₂ and NH₃ precursors. Field emission scanning emission microscopy, Raman spectroscopy, Fourier transform infrared spectroscopy and small angle X-ray scattering were employed to study structural and microstructural properties of a-SiN:H films. The rms surface roughness increased with increase of positive bias to substrate. Intermediate range order, porosity and interface inhomogeneity in amorphous of a-SiN:H films evaluated by acoustic and optical phonon of silicon network, Guinier plot and correlated length from Raman and SAXS characterizations. The fractal behavior of a-SiN:H domains approached the perfect symmetry and the intermediate range order of a-SiN:H films deteriorate with increase of the positive substrate bias. Both correlation length and void size of the a-SiN:H amorphous domain increased with increase of the substrate bias from 0 to +200 V.     

Generation of optically active states in a-SiNx by thermal treatment

Amorphous silicon nitride (a-SiN_x) films were deposited using plasma-enhanced chemical-vapor deposition (PECVD) and subsequently, thermal annealing processes were performed at 700-1000 °C in the ultra-high vacuum (UHV) condition. A strong photoluminescence (PL) peak induced by luminescent defect centers was observed at 710 nm for the as-deposited sample. When the sample was annealed at 700-1000 °C, the PL peak intensity became about 3-12 times stronger with no shift of the PL peak. To investigate the origin of the change in PL peak intensity after the thermal annealing, Si 2p and N 1s core-level spectra were systematically analyzed by high-resolution photoemission spectroscopy (HRPES) using synchrotron radiation. In particular, N 1s spectra were decomposed with three characteristic nitrogen-bonding states. It is revealed that the nitrogen bonding state with N-Si and NSi₂ configurations (denoted as N3) contributes mainly to the change in PL peak intensity. We note that luminescent nitrogen related defect centers such as N₄⁺ and N₂° are localized in the state N3. Detailed analysis of the experimental results shows that the state N3 is located in the interface bounded by the region of the nano-sized stoichiometric silicon nitride Si₃N₄ (denoted as N1) and is considerably influenced by the thermal annealing, which is an appropriate process to cause strong photoluminescence of the related samples as mentioned above.     

Anodization of aluminium thin films on pSi and annihilation of strong luminescence from Al2O3

Photoluminescence (PL) of Al₂O₃ films obtained by anodization of thermally evaporated and annealed thin Al films on p⁺⁺Si in 0.3 M oxalic acid has been investigated. Thermal annealing at 200–950 °C under the dry nitrogen atmosphere was used for deactivation of luminescence centres. Luminescence from as grown films was broad and located at 425 nm. This luminescence reached to highest level after annealing at 600 °C. Maximum 10 min was required for full optical activation and prolonged annealing up to 4 h did not change the luminescence intensity. Because of deep levels, absorption band edge of as grown films was shifted to the lower energy which is 3.25 eV. Annealing above 800 °C reduced the PL intensity and this observation was correlated with the blue shift of band edge as the defects annealed out. Disappearing PL intensity and blue shift of band edge absorption after annealing at 950 °C was mainly attributed to the oxygen-related defects and partly to impurities that may be originated from oxalic acid. AFM results did not show any hexagonally ordered holes but uniformly distributed nanosized Al₂O₃ clusters that were clearly seen. XRD measurements on as grown Al₂O₃ showed only [1 1 0] direction of α phase. Debye–Scherer calculation for this line indicates that cluster size is 35.7 nm. XRD and AFM pictures suggest that nanocrystalline Al₂O₃ are embedded in amorphous Al₂O₃.     

Influence of the ion synthesis and ion doping regimes on the effect of sensitization of erbium emission by silicon nanoclusters in silicon dioxide films

The photoluminescence spectra of erbium centers in SiO₂ films with ion-synthesized silicon nanoclusters under nonresonant excitation were investigated. Erbium was introduced into thermal SiO₂ films by ion implantation. The dependences of photoluminescence intensity on the dose, the order of ion implantation of Si and Er, the annealing temperature, and additional Ar⁺ and P⁺ ion irradiation regimes, i.e., factors determining the influence of radiation damage and doping on sensitization of erbium luminescence by silicon nanoclusters, were determined. It was found that the sensitization effect and its amplification due to doping with phosphorus are most pronounced under the conditions where nanoclusters are amorphous. The quenching of photoluminescence due to radiation damage in this case manifests itself to a lesser extent than for crystalline nanoclusters. The role of various factors in the observed regularities was discussed in the framework of the existing concepts of the mechanisms of light emission and energy exchange in the system of silicon nanoclusters and erbium centers.     

Synchrotron investigations of electronic and atomic-structure peculiarities for silicon-oxide films’ surface layers containing silicon nanocrystals

Films obtained using molecular-beam deposition of SiO powder on c-Si (111) substrates for the purpose of SiO2 system formation with silicon nanocrystals were investigated before and after 900–1100°C annealing by photoluminescence, ultrasoft X-ray emission spectroscopy, X-ray photoelectron spectroscopy, X-ray absorption near-edge structure spectroscopy, and X-ray diffraction. The appearance of (111)-oriented luminescent silicon nanoclusters in considerable amounts upon annealing at T = 1000–1100°C is established in the investigated films. An anomalous phenomenon of X-ray absorption quantum yield intensity reversal for the L _2,3 elementary silicon edge is detected. Models for this phenomenon are suggested.     

Luminescent silicon nanocrystal dots fabricated by SiCl4/H2 RF plasma-enhanced chemical vapor deposition

Luminescent nanocrystalline Si dots were fabricated directly on thermally grown SiO₂ at 120°C by conventional RF plasma-enhanced chemical vapor deposition using tetrachlorosilane, SiCl₄ and H₂. As-deposited Si dot exhibits photoluminescence (PL) in the visible region, consisting of two broad bands corresponding to photon energies of 1.38 and 1.48 eV. Storage in air enhances PL and shifts the PL peak energy to higher wavelengths for dots of diameter less than 10 nm. Fourier transform attenuated total reflection absorption spectroscopy (FTIR-ATR) study reveals that the spontaneous oxidation proceeds until saturation after 70 h at dot sizes of 3–5 nm. The relationship between PL intensity, blueshift of PL peak energy, and surface termination species during oxidation indicates that these changes are attributed to the increased density of radiative centers at the Si nanocrystal dot/SiO₂ interface and enhancement of the quantum confinement effect.