胆盐与磷酸钙的相互作用

胆汁的pH条件下(pH=6～8)，应该生成无定形磷酸钙(ACP)，而在胆结石中磷酸钙通常以羟基磷灰石的形式出现.利用谱学方法研究了ACP与胆盐的作用.结果表明，胆盐以胶团的形式与ACP作用，在溶液中形成复合胶团，使其溶解度增加.不同类型胆盐与ACP的作用能力不同：脱氧胆酸钠(NaDC) > 牛磺胆酸钠(NaTC) > 胆酸钠(NaC).胆盐与ACP中结合钙的亲和能力大于结合钙的亲和能力，使ACP在胆汁的环境下容易转化为羟基磷灰石.     

Carbonate adsorption on goethite in competition with phosphate

Competitive interaction of carbonate and phosphate on goethite has been studied quantitatively. Both anions are omnipresent in soils, sediments, and other natural systems. The PO4-CO3 interaction has been studied in binary goethite systems containing 0-0.5 M (bi)carbonate, showing the change in the phosphate concentration as a function of pH, goethite concentration, and carbonate loading. In addition, single ion systems have been used to study carbonate adsorption as a function of pH and initial (H)CO3 concentration. The experimental data have been described with the charge distribution (CD) model. The charge distributions of the inner-sphere surface complexes of phosphate and carbonate have been calculated separately using the equilibrium geometries of the surface complexes, which have been optimized with molecular orbital calculations applying density functional theory (MO/DFT). In the CD modeling, we rely for phosphate on recent parameters from the literature. For carbonate, the surface speciation and affinity constants have been found by modeling the competitive effect of CO3 on the phosphate concentration in CO3-PO4 systems. The CO3 constants obtained can also predict the carbonate adsorption in the absence of phosphate very well. A combination of inner- and outer-sphere CO3 complexation is found. The carbonate adsorption is dominated by a bidentate inner-sphere complex, (FeO)2CO. This binuclear bidentate complex can be present in two different geometries that may have a different IR behavior. At a high PO(4) and CO3 loading and a high Na+ concentration, the inner-sphere carbonate complex interacts with a Na+ ion, probably in an outer-sphere fashion. The Na+ binding constant obtained is representative of Na-carbonate complexation in solution. Outer-sphere complex formation is found to be unimportant. The binding constant is comparable with the outer-sphere complexation constants of, e.g., SO(2-)4 and SeO(2-)4.     

Interaction of hydroxyapatite with sodium chondroitin sulfate and calcium chondroitin sulfate in an aqueous phase

The suspension pH at a given concentration of hydroxyapatite (HAP) decreased with the concentration of calcium chondroitin-6-sulfate (CaChs), whereas it increased with the concentration of sodium chondroitin-6-sulfate (Na2Chs). The former effect is due to the increase in the concentration of H+ by ion exchange between H+ on the surface of HAP and Ca2+ of CaChs, and the latter is due to the protonation of phosphate ion (Pi) released from the surface of HAP. The absorbed amount of chondroitin-6-sulfate anion (Chs) by HAP was higher with CaChs than with Na2Chs over the concentration range examined. The equilibrium concentration of Pi decreased with increasing concentration of added CaChs because the concentration of free Ca2+, which dissociates from CaChs, regulates the free concentration of Pi through the restriction of the solubility product of HAP (Ksp). In contrast, that in the presence of Na2Chs increased with increasing concentration of added Na2Chs owing to the anion exchange between Chs and Pi of the HAP surface. The total concentration of Ca2+, which was released from HAP into the solution phase, increased after passing through a minimum with increasing concentration of added Na2Chs. That is, the concentration of Ca2+ free from Chs decreased with an increase in the concentration of released Pi owing to the restriction of the solubility product, whereas that of Ca2+ bound by Chs increased with increasing concentration of added Na2Chs through the ion exchange of Na+ with Ca2+. It was confirmed by the dialysis method that the value of Ksp was almost constant around 10, although HAP dissolves incongruently in the presence of Na2Chs.     

Characterization of active phosphorus surface sites at synthetic carbonate-free fluorapatite using single-pulse 1H, 31P, and 31P CP MAS NMR

The chemically active phosphorus surface sites defined as PO(x), PO(x)H, and PO(x)H2, where x = 1, 2, or 3, and the bulk phosphorus groups of PO4(3-) at synthetic carbonate-free fluorapatite (Ca5(PO4)3F) have been studied by means of single-pulse 1H,31P, and 31P CP MAS NMR. The changes in composition and relative amounts of each surface species are evaluated as a function of pH. By combining spectra from single-pulse 1H and 31P MAS NMR and data from 31P CP MAS NMR experiments at varying contact times in the range 0.2-3.0 ms, it has been possible to distinguish between resonance lines in the NMR spectra originating from active surface sites and bulk phosphorus groups and also to assign the peaks in the NMR spectra to the specific phosphorus species. In the 31P CP MAS NMR experiments, the spinning frequency was set to 4.2 kHz; in the single-pulse 1H MAS NMR experiments, the spinning frequency was 10 kHz. The 31P CP MAS NMR spectrum of fluorapatite at pH 5.9 showed one dominating resonance line at 2.9 ppm assigned to originate from PO4(3-) groups and two weaker shoulder peaks at 5.4 and 0.8 ppm which were assigned to the unprotonated PO(x) (PO, PO2-, and PO3(2-)) and protonated PO(x)H (PO2H and PO3H-) surface sites. At pH 12.7, the intensity of the peak representing unprotonated PO(x) surface sites has increased 1.7% relative to the bulk peak, while the intensity of the peaks of the protonated species PO(x)H have decreased 1.4% relative to the bulk peak. At pH 3.5, a resonance peak at -4.5 ppm has appeared in the 31P CP MAS NMR spectrum assigned to the surface species PO(x)H2 (PO3H2). The results from the 1H MAS and 31P CP MAS NMR measurements indicated that H+, OH-, and physisorbed H2O at the surface were released during the drying process at 200 degrees C.     

Neutral bidentate organophosphorus compounds as novel ionophores for potentiometric membrane sensors for barium(II)

Bis(diarylphosphine oxide) naphthalene compounds are used as novel ionophores in plasticized poly(vinyl chloride) matrix membrane sensors for barium ions. The most favorable sensor was 1,2-bis(diethylphenylphosphine oxide)naphthalene containing potassium tetrakis(4-chlorophenyl)borate as lipophilic salt and o-nitrophenyloctyl ether as plasticizer for ion-selective electrode membrane construction. The electrode showed excellent properties. It gave a linear response with a Nernstian slope of 30 mV per decade within the concentration range 10(-1)-10(-5) mol L(-1) BaCl2. The electrode exhibits a high selectivity towards Ba2+ with respect to Li+, Na+, K+, Rb+, Cs+, NH4+, Ag+, Mg2+, Ca2+, Sr2+, Mn2+, Fe2+, Co2+, Ni2+, Cu2+, Zn2+, Cd2+, Pb2+, Al3+, La3+, and Ce3+ ions. The electrode response was stable over a wide pH range (3-11). The lifetime of the electrode was about 2 months. It was successfully applied to the determination of Ba2+ contents in some rocks.     

Binding of phosphate with a simple hexaaza polyammonium macrocycle

A mixture of dihydrogen phosphate and phosphoric acid has been crystallized with a hexaprotonated 26-membered polyammonium macrocycle, 1,4,7,14,17,20-hexaazacyclohexacosane, as the counterion. The complex crystallizes in the monoclinic space group P2(1)/c with unit cell parameters of a = 10.006(2) A, b = 12.525(1) A, c = 19.210(2) A, beta = 102.91(1) degrees, and V = 2346.6(5) A3. The hexaprotonated macrocycle is located on a crystallographic center of inversion and is surrounded by eight phosphate anions. Six of the phosphates are dihydrogen phosphates (H2PO4-), and the other two are neutral phosphoric acid molecules. Intricate hydrogen-bonding networks, involving the anionic and neutral phosphates and the protonated macrocycle, dominate the crystal lattice. Potentiometric studies using NaCl as the supporting electrolyte indicate high formation constants for the triprotonated macrocycle, H3L3+, with PO4(3-) at pH approximately 9.5 (log K = 4.55(4)), for the tetraprotonated macrocycle, H4L4+, with monohydrogen phosphate, HPO4(2-), at pH approximately 8.0 (log K = 6.01(3)), and for ditopic complexes with H5L5+ and H6L6+ and dihydrogen phosphate, H2PO4-, at pH approximately 4.0 (log K = 6.16(6)) and pH approximately 2.5 (log K = 6.44(5)), respectively. The ditopic behavior in the simple polyazamacrocycle receptor is a somewhat unusual occurrence, as is the finding of phosphoric acid species in the crystal structure.     

Structural and morphological consequences of high-temperature treatments of hydroxyapatite in the absence or presence of HCl vapor

Hydroxyapatite [HAP; Ca5(PO4)3(OH)], a biocompatible, osteoconductive material, was perceived, in the present investigation, to mimic a healthy bone mineral. Structural and morphological properties of its bulk and surface were examined versus high-temperature (up to 900 degrees C) thermal treatments in air or wet HCl gas atmosphere, using thermogravimetry, X-ray powder diffractometry, N2 sorptiometry, scanning electron microscopy, X-ray energy dispersive spectroscopy, and ex- and in situ infrared spectroscopy. CO, CDCl3, and methylbutynol were used as infrared probe molecules. Results obtained revealed that, in the absence of HCl, the bulk crystalline structure and the chemical composition of HAP were stable during high-temperature treatments. The surface exposed isolated Lewis acid sites (Ca2+) and reactive base sites (O(x-) and/or OH-) that chemisorbed atmospheric CO2 molecules with the formation of surface carbonate species (CaCO3). It is assumed that surface OH groups may interact with atmospheric oxygen molecules, leading to the formation and incorporation of peroxide (O2(2-) species. In the atmosphere of wet HCl, HAP was shown to suffer loss of chemical integrity, facilitated by its carbonated domains, as well as disintegration (or erosion) of particle aggregates and creation of what appeared to be deep groves.     

'On-off-on' fluorescent indicators of pH windows based on three separated components

'On-off-on' fluorescent indicators for pH windows are obtained with ternary systems in which the three separated components are Cu2+, a tetraaza ligand and the fluorophore Coumarin 343: protonation of Coumarin 343, its coordination to Cu2+ and its displacement from Cu2+ by OH- give an inverse bell-shaped variation of emission with pH.     

A coated wire-type lead(II) ion-selective electrode based on a phosphorylated calix[4]arene derivative.

The preparation of a lead-selective electrode based on 5,11,17,23-tetra-tert-butyl-25,26,27,28-tetrakis-(diphenylphosphinoylmethoxy)calix[4]arene (1) as an ionophore is reported. The plasticized PVC membrane containing 30% PVC, 57% ortho-nitrophenyloctylether (NPOE), 4% sodium tetraphenylborate (NaTPB) and 9% ionophore 1 was directly coated on a graphite electrode. It exhibits a nearly Nernstian slope of 28.0 +/- 0.2 mV decade(-1) over a concentration range of 1 x 10(-5) - 1 x 10(-2) mol dm(-3) with a detection limit of 1.4 x 10(-6) mol dm(-3). The response time of the electrode was found to be ca. 17 s. The potential of the sensor was independent of the pH variation in the range 3.5 - 5.0. The selectivity of the electrode performance towards lead ions over Th4+, La3+, Sm3+, Dy3+, Y3+, Ca2+, Sr2+, Cd2+, Mn2+, Zn2+, Ni2+, Co2+, NH4+ Ag+, Li+, Na+ and K+ ions was investigated. The prepared electrode was used successfully as an indicator electrode for a potentiometric titration of a lead solution using a standard solution of EDTA. The applicability of the sensor for Pb2+ measurements in various synthetic water samples spiked with lead nitrate was also checked.     

On-column complexation of metal ions using 2,6-pyridinedicarboxylic acid and separation of their anionic complexes by capillary electrophoresis with direct UV detection

On-column complexation of metal ions with 2,6-pyridinedicarboxylate (2,6-PDC) to form anionic complexes enabled their separation by capillary zone electrophoresis with direct UV detection at 214 nm. Nine metal ions, Cu2+, Zn2+, Ni2+, Cd2+ Mn2+, Pb2+, Fe3+, Al3+ and Ca2+, were determined in less than 7 min using 10 mM 2.6-PDC solution containing 0.75 mM tetradecyltrimethylammonium bromide at pH 4.0. Satisfactory working ranges (20-300 microM), detection limits (3-10 microM) and good repeatability of the peak areas (RSD 2.1-4.2%, n=5) were obtained using hydrodynamic injection (30 s). The proposed method was used successfully for the determination of Mn2+, Fe3+, Al3+ and Ca2+ in groundwaters.     

不同形态的氧氟沙星在凹凸棒土上的吸附特征

通过控制反应体系的pH值,探究了阳离子、兼性和阴离子形态的氧氟沙星(OFL,3种形态分别记为OFL~+,OFL~±和OFL~-)在凹凸棒土(ATP)上的吸附特征.实验结果表明,OFL~+主要通过与ATP表面的Ca~(2+),Mg~(2+)进行阳离子交换吸附于ATP上,当其吸附量较高时,会存在少量的氢键;OFL~±和OFL~-可与ATP表面的铁氧化物、铝氧化物进行表面络合,也可与溶液中从ATP中溶解出的Ca~(2+)和Mg~(2+)形成络合物,再通过静电作用吸附于ATP上.在中性至微碱性(pH=7.10~7.70)条件下,由于Ca的电负性小于Mg,[Ca~(2+)-OFL]+不能稳定地存在于溶液中,使得OFL±与Ca~(2+)进行阳离子交换而与Mg~(2+)形成络合物,再通过静电作用吸附于ATP上.当OFL主要以OFL~-形态存在于溶液中时(p H=9.00~10.00),Ca~(2+)和Mg~(2+)均可与OFL~-形成络合物,再通过静电作用吸附于ATP上.     

Simultaneous removal of ammonium and phosphate by zeolite synthesized from fly ash as influenced by salt treatment

To develop an effective technique for enhancing the removal efficiency of ammonium and phosphate at low concentrations without losing potential removal capacity, Na-ZFA (zeolite synthesized from fly ash) was converted into Ca-, Mg-, Al-, and Fe-ZFA by salt treatment and the simultaneous removal of ammonium and phosphate by ZFA saturated with different cations was investigated. It was shown that Al3+-ZFA had the highest removal efficiencies (80-98%) for ammonium, followed by Mg2+ (43-58%), Ca2+ (40-54%), Na+ (<20%), and Fe3+ (<1%). Both alkaline pH values (in the cases of Na+, Ca2+, Mg2+) and acidic pH value (in the case of Fe3+) inhibited the sequestration of ammonium. At low initial phosphate concentrations, the efficiency of phosphate removal by Al3+- and Fe3+-ZFA approached 100%, followed by Ca2+ (60-85%), Na+ (<25%), and Mg2+ (<5%). The difference in phosphate removal efficiency was explained by the adsorption mechanisms. It was concluded that ZFA could be used in simultaneous removal of NH4+ and phosphate at low concentrations with presaturation by an appropriate cation such as Al3+ through salt treatment.     

Acid-base and metal-ion-binding properties of xanthosine 5'-monophosphate (XMP) in aqueous solution: complex stabilities, isomeric equilibria, and extent of macrochelation

The four acidity constants of threefold protonated xanthosine 5'-monophosphate, H3(XMP)+, reveal that at the physiological pH of 7.5 (XMP-H)(3-) strongly dominates (and not XMP(2-) as given in textbooks); this is in contrast to the related inosine (IMP(2-)) and guanosine 5'-monophosphate (GMP(2-)) and it means that XMP should better be named as xanthosinate 5'-monophosphate. In addition, evidence is provided for a tautomeric (XMP-HN1)(3-)/(XMP-HN3)(3-) equilibrium. The stability constants of the M(H;XMP)+ species were estimated and those of the M(XMP) and M(XMP-H)- complexes (M2+=Mg2+, Ca2+, Sr2+, Ba2+, Mn2+, Co2+, Ni2+, Cu2+, Zn2+, Cd2+) measured potentiometrically in aqueous solution. The primary M2+ binding site in M(XMP) is (mostly) N7 of the monodeprotonated xanthine residue, the proton being at the phosphate group. The corresponding macrochelates involving P(O)2(OH)- (most likely outer-sphere) are formed to approximately 65% for nearly all M2+. In M(XMP-H)- the primary M2+ binding site is (mostly) the phosphate group; here the formation degree of the N7 macrochelates varies widely from close to zero for the alkaline earth ions, to approximately 50% for Mn2+, and approximately 90% or more for Co2+, Ni2+, Cu2+, Zn2+, and Cd2+. Because for (XMP-H)(3-) the micro stability constants quantifying the M2+ affinity of the xanthosinate and PO3(2-) residues are known, one may apply a recently developed quantification method for the chelate effect to the corresponding macrochelates; this chelate effect is close to zero for the alkaline earth ions and it amounts to about one log unit for Co2+, Ni2+, Cu2+. This method also allows calculation of the formation degrees of the monodentatally coordinated isomers; this information is of relevance for biological systems because it demonstrates how metal ions can switch from one site to another through macrochelate formation. These insights are meaningful for metal-ion-dependent reactions of XMP in metabolic pathways; previous mechanistic proposals based on XMP(2-) need revision.     

羟基磷灰石对牛血清白蛋白的吸附特性研究

研究了羟基磷灰石表面电位随溶液PO₄^3-浓度、Ca²⁺浓度、离子强度和pH的变化规律;测定了不同操作条件下牛血清白蛋白在羟基磷灰石上的吸附容量;吸附等温线的测定结果表明该吸附属于Langmuir型;通过对该吸附过程的动力学研究,计算得到的表观活化能和吸附热数值较低,表明该吸附是物理吸附.     

Elucidation of adsorption mechanism of bone-staining agent alizarin red S on hydroxyapatite by FT-IR microspectroscopy

To elucidate adsorption mechanism of alizarin red S (ARS), which is often used for staining bones in histology, adsorption of ARS on hydroxyapatite, Ca10(PO4)6(OH)2 (HAP), was investigated by a batch method, compared with alizarin, phenols, and benzenesulfonates. We found that ionized 1-, 2-OH groups (1-, 2-O(-)) of ARS can be electrostatically bound to Ca2+ on HAP, but that the 3-SO3(-) group of ARS hardly participates in adsorption on HAP. ARS-adsorbed HAP (ARS-HAP) in dark reddish violet was also prepared and analyzed by FT-IR microspectroscopy to gain structural information on bonding between ARS and HAP. The obtained spectrum, which was converted to difference spectra, indicated a single band of nu(C=O) at 1627 cm(-1) and two types of symmetric C=O stretching bands of nu(s)(C=O) + nu(C=C) at 1345 cm(-1) and nu(s)(C=O) + delta(O-C=C) at 1272 cm(-1). These bands imply the existence of a salt form in ARS-HAP via 1-, 2-OH groups of ARS. As a result of the existence of a chelate form in ARS-HAP via 1-OH and 9-C=O groups of ARS, two bands of nu(C=C) + nu(C=O) at 1572 cm(-1) and nu(C=O) + nu(C=C) at 1537 cm(-1) were also observed. In addition, ARS was almost desorbed from colored ARS-HAP at 50 degrees C by using neutral phosphate buffer to recover slightly pale pinkish HAP, or De-ARS-HAP. The desorbed ARS belongs to ARS previously adsorbed on HAP by salt formation, while the remaining color on De-ARS-HAP indicates ARS still adsorbed on HAP by chelate formation. Consequently, we elucidated two adsorption mechanisms of ARS on HAP: The major adsorption is salt formation made up with 1-, 2-O(-) of ARS and Ca2+ on HAP, and the minor adsorption is chelate formation made up with 1-O(-) and 9-C=O of ARS and Ca2+ on HAP.     

Modeling of ionic equilibria of trace metals (Cu2+, Zn2+, Cd2+) in concentrated aqueous electrolyte solutions at 25 degrees C

This work presents a model of activity coefficients and a database for ionic equilibria of Cu2+, Zn2+, and Cd2+ in (H+, Na+, K+, Mg2+, Ca2+)(OH-, Cl-, NO-3, ClO-4, HSO-4, SO2-(4), HCO-3, CO(2-)3) aqueous media valid up to 6-12 m ionic strength. The activity coefficient of a dissolved species is represented by empirical equation [Formula: see text] , where Agamma is Debye-Hückel constant (1.17 at 25 degrees C), gammai and zi are activity coefficient and charge of a dissolved species i, I is molal ionic strength, bij is model parameter, and mj is molal concentration of dissolved species. The model is applicable to the modeling of ionic equilibria, as well as to simulation of solubility of salts in mixed electrolyte solutions.     

Sorption of Selenite (SeO(3)(2-)) on Hydroxyapatite: An Exchange Process

The sorption of SeO(3)(2-) on hydroxyapatite surface was investigated in batch experiments over a range of pH and SeO(3)(2-) concentrations in the absence and presence of additional Ca and PO(4). The sorption is pH dependent with a maximum observed at pH values generally encountered in natural waters. While the presence of phosphate lowers SeO(3)(2-) sorption by direct competition, the presence of calcium enhances it. In order to identify the mechanism of sorption and the nature of the surface sites, microscopic observation and spectroscopic methods such as X-ray diffraction and X-ray photoelectron spectroscopy were used. Surface complexation, coprecipitation, and precipitation processes were ruled out. Localization of sorbed selenium in the crystallographic sites where phosphorus is normally located shows that selenite is sorbed on the apatite by an anionic exchange with phosphate groups. Although the exact equilibria involved could not be established, the stoichiometry of the exchange is close to 1 : 1. According to kinetics experiments and X-ray diffraction analyses, it seems that selenium is not exclusively located at the surface but diffuses slightly in a thickness of a few nanometers. Copyright 2000 Academic Press.     

Incongruent dissolution of hydroxyapatite in the presence of phosphoserine

Concentrations of phosphate and calcium ions, liberated from the surface of hydroxyapatite (HAP) during the adsorption of phosphoserine (PSer), were determined at 30°C. HAP showed a marked incongruent dissolution behavior in the presence of PSer. That is, the concentration of phosphate ion in solution increases with the addition of PSer due to the ion-exchange between PSer and phosphate ion on HAP (molar ratio of the former to the latter=32), whereas the concentration of calcium ion decreases with this release of phosphate ion, because the solubility product of HAP restricts the concentrations of both ions in solution (calculated values of — log (Ca²⁺)¹⁰ (PO ₄ ^3– )⁶ (OH^–)² were 115.8±1.0). The affinity of PSer to HAP was highest at pH 5.8 where the PSer and the HAP surface had the opposite charges. This electrostatic attraction force between PSer and HAP was shielded to some extent by the addition of KCl.     

ESR study of aqueous micellar solutions of perfluoropolyether surfactants with the use of fluorinated spin probes

The acid-base properties of synthetically prepared and well-characterized hydroxyapatite (HAP) in contact with KNO3 solutions were investigated at 25 degrees C, through potentiometric titrations, zeta-potential measurements, and surface complex modeling. Aliquots of suspension were withdrawn every 0.5 pH unit during the titration procedure and analyzed for calcium and phosphate. It was found that, even for rapid titration experiments, a remarkable amount of H+ ions (H+dissol.) is consumed in the bulk solution in reacting with species coming from the dissolution of HAP. These H+ ions must be taken into account in the H+ mass balance, in order for true value for the point of zero charge (pzc=6.5+/-0.2) and consequently true value for the surface charge (sigma0) to be obtained. Besides the conventional potentiometric titration technique, it was found that pzc may be determined much more easily as the intersection point of the suspension titration curve and the blank one modified to include the amount of H+dissol. obtained at one ionic strength. Finally, a surface complexation model was proposed for the development of surface charge. Experimental data were satisfactorily fitted by using the value of 4.2 F m-2 for the capacitance.     

多晶Fe60Ni40合金阳极钝化膜的XPS研究

过渡金属Fe、Ni或其合金由于它们具有磁性和在工业上被用作催化剂等，它们与氧化腐蚀性气体02、C12等的作用已被广泛研究［‘－3］．含Ni的不锈钢和含Ni50％的FeNi基合金在酸性溶液中表现出比铁更好的耐腐蚀性并增强了氧化钝化层的附着力，放它们在溶液的腐蚀与钝性研究已引起广泛的兴趣，甚至包括对F6Ni基非晶合全玻璃的腐蚀与钝性研究【4一刊，用不同的方法研究溶液状态下的自然氧化膜或阳极钝化膜，得出的结果不同，对腐蚀与钝性解释也很不一致，硼酸一础砂或磷酸一磷酸盐缓冲液在工业上被广泛用作清洗剂、缓蚀剂或成膜剂等·因此，…