A flow injection procedure based on solenoid micro-pumps for spectrophotometric determination of free glycerol in biodiesel

A flow system designed with solenoid micro-pumps is proposed for fast and greener spectrophotometric determination of free glycerol in biodiesel. Glycerol was extracted from samples without using organic solvents. The determination involves glycerol oxidation by periodate, yielding formaldehyde followed by formation of the colored (3,5-diacetil-1,4-dihidrolutidine) product upon reaction with acetylacetone. The coefficient of variation, sampling rate and detection limit were estimated as 1.5% (20.0 mg L⁻¹ glycerol, n = 10), 34 h⁻¹, and 1.0 mg L⁻¹ (99.7% confidence level), respectively. A linear response was observed from 5 to 50 mg L⁻¹, with reagent consumption estimated as 345 μg of KIO₄ and 15 mg of acetylacetone per determination. The procedure was successfully applied to the analysis of biodiesel samples and the results agreed with the batch reference method at the 95% confidence level.     

Modification of glassy carbon electrode with a polymer/mediator composite and its application for the electrochemical detection of iodate

A modified glassy carbon electrode was prepared by depositing a composite of polymer and mediator on a glassy carbon electrode (GCE). The mediator, flavin adenine dinucleotide (FAD) and the polymer, poly(3,4-ethylenedioxythiophene) (PEDOT) were electrochemically deposited as a composite on the GCE by applying cyclic voltammetry (CV). This modified electrode is hereafter designated as GCE/PEDOT/FAD. FAD was found to significantly enhance the growth of PEDOT. Electrochemical quartz crystal microbalance (EQCM) analysis was performed to study the mass changes in the electrode during the electrodeposition of PEDOT, with and without the addition of FAD. The optimal cycle number for preparing the modified electrode was determined to be 9, and the corresponding surface coverage of FAD (Γ_FAD) was ca. 5.11 × 10⁻¹⁰ mol cm⁻². The amperometric detection of iodate was performed in a 100 mM buffer solution (pH 1.5). The GCE/PEDOT/FAD showed a sensitivity of 0.78 μA μM⁻¹ cm⁻², a linear range of 4–140 μM, and a limit of detection of 0.16 μM for iodate. The interference effects of 250-fold Na⁺, Mg²⁺, Ca²⁺, Zn²⁺, Fe²⁺, Cl⁻, NO₃⁻, I⁻, SO₄²⁻ and SO₃²⁻, with reference to the concentration of iodate were negligible. The long-term stability of GCE/PEDOT/FAD was also investigated. The GCE/PEDOT/FAD electrode retained 82% of its initial amperometric response to iodate after 7 days. The GCE/PEDOT/FAD was also applied to determine iodate in a commercial salt.     

Detection of transferrin isoforms in human serum: comparison of UV and ICP–MS detection after CZE and HPLC separations

Two methods for separation of transferrin (Tf) sialoforms, capillary electrophoresis (CE) and high performance liquid chromatography (HPLC) with conventional UV absorbance detection, have been investigated and compared. First, conditions affecting the separation of the Tf isoforms by capillary zone electrophoresis and HPLC were carefully optimized. The use of 15 mmol L⁻¹ borate buffer (pH 8.4) containing 3 mmol L⁻¹ diaminobutane (DAB) as additive enabled good separation of the Tf isoforms by CE (75 cm×50 μm i.d. fused silica capillary) at 25 kV. In HPLC, a gradient of ammonium acetate (from 0 to 250 mmol L⁻¹ in 45 min) buffered at pH 6 (Tris-HCl) proved suitable for separation of Tf isoforms on a Mono-Q HR 5/5 anion-exchange column. On-line specific detection of the iron associated with the different Tf isoforms, after Fe saturation, by inductively coupled plasma mass spectrometry (ICP–MS) was studied in detail to compare its analytical performance with UV detection. For both CE and HPLC an octapole reaction system (ORS) ICP–MS instrument was used to minimize polyatomic interferences on the ⁵⁶Fe major isotope. Limits of detection of the different isoforms were in the range of 0.02–0.04 μmol L⁻¹ Tf for HPLC–ICP (ORS)–MS. This hybrid technique proved more selective and reliable detection of transferrin isoforms with 2, 3, 4, 5, and 6 sialic acid residues (S₂, S₃, S₄, S₅, and S₆) in real serum samples. Interesting results from iron speciation of Tf in serum from healthy individuals and from pregnant women are given.     

Dioxouranium(VI)-carboxylate complexes: A calorimetric and potentiometric investigation of interaction with oxalate at infinite dilution and in NaCl aqueous solution at I = 1.0 mol L and T = 25 °C

In this paper we investigated the interactions between dioxouranium(VI) and oxalate using (H⁺-glass electrode) potentiometry and titration calorimetry. Potentiometric measurements were carried out in NaCl aqueous solutions and at T = 25 °C in a wide range of experimental conditions (concentrations, ligand/metal molar ratio, pH, titrants) at low ionic strength values (I ≤ 0.090 mol L⁻¹, without supporting electrolyte) and at I = 1.0 mol L⁻¹; different procedures were employed for the acquisition of experimental data and careful analysis of these data performed. In all cases the speciation model that best fits experimental data takes into account the formation of the binary mononuclear species UO₂(ox)⁰, UO₂(ox)₂²⁻, UO₂(ox)₃⁴⁻ widely reported in literature, the ternary hydroxyl mononuclear species UO₂(ox)OH⁻, UO₂(ox)(OH)₂²⁻, UO₂(ox)₂OH³⁻, UO₂(ox)₃OH⁵⁻, the protonated ternary mononuclear species UO₂(ox)₃H³⁻ and the binuclear species (UO₂)₂(ox)₅⁶⁻.Calorimetric measurements were carried out following similar procedures and in the same experimental conditions as employed for the potentiometric measurements at I = 1.0 mol L⁻¹ in NaCl. The stability of UO₂²⁺-oxalate²⁻ complexes is fairly high and their main contribution to stability is entropic in nature. Some linear empirical relationships were found which make it possible to calculate (i) the contribution of a single bond: and ; (ii) chelate stabilisation per ring: and and (iii) the mean stability of negatively charged Na⁺-ion pair complexes: log^TK = (0.46 ± 0.02)·|z| (z = charge of complex species), ΔG° = −(2.60 ± 0.1)·|z| kJ mol⁻¹ and TΔS° = 2.5 ± 0.5 kJ mol⁻¹. Both potentiometric and calorimetric results provide evidence of the penta-coordination of the species UO₂(ox)₃⁴⁻. SIT parameters were calculated from the data at I = 0 and I = 1.02 mol kg⁻¹. Comparisons are made with literature data. An insoluble dioxouranium(VI) ternary complex was synthesised (at I = 1.0 mol L⁻¹ in NaCl) and characterised by thermoanalysis and elemental analysis.     

Determination of Glycerol in Biodiesel Using a Nickel(II) Oxyhydroxide Chemically Modified Electrode by Cyclic Voltammetry

A glassy carbon electrode chemically modified with nickel oxyhydroxide from a nickel hexacyanoferrate (NiHCF) film was used to determine glycerol in biodiesel by cyclic voltammetry. The modified electrode exhibited a linear response to glycerol concentration in the range from 0.05 to 0.35 mmol L^?1, and a detection limit of 0.030 mmol L^?1. The glycerol concentration found in the biodiesel sample was 0.156 mmol L^?1. The method developed in this study showed a recovery of (100.3±5.0)%.     

Reactions of the metallocene dichlorides [M(Cp)2Cl2] (M = Zr, Hf) and [Ti(MeCp)2Cl2] with the pyridine-2,6-dicarboxylate(−2) ligand: Synthesis, spectroscopic characterization and X-ray structures of the products

The reactivity pattern of the 16-electron species [M(Cp)₂Cl₂] (M = Zr, Hf; Cp⁻ = η⁵-C₅H₅⁻) and [Ti(MeCp)₂Cl₂] (MeCp⁻ = η⁵-C₅H₄CH₃⁻) towards the dipicolinate(−2) (dipic²⁻) ligand under mild (ambient temperature) and convenient (aerobic reactions, aqueous media) conditions have been investigated. The syntheses, molecular structures and spectroscopic (IR, ¹H NMR) characterization are reported for the 18-electron products [Zr(Cp)₂(dipic)] (1), [Hf(Cp)₂(dipic)] (2) and [Ti(MeCp)₂(dipic)] (3). The dipic²⁻ ion behaves as N,O,O′-chelating ligand in the three complexes, while the centroids of the Cp⁻ (1, 2) and MeCp⁻ (3) rings formally occupy the fourth and fifth coordination sites about the central metal. The two identical/very similar bite angles of only ∼70° make the dipic²⁻ ligand particularly suited to form stable metallocene derivatives with 5-coordinate geometry. IR and ¹H NMR data are discussed in terms of the known structures and the tridentate chelating mode of the dipic²⁻ ligand.     

Sensitive determination of verticine and verticinone in Bulbus Fritillariae by ionic liquid assisted capillary electrophoresis-electrochemiluminescence system

CE/Ru(bpy)₃²⁺ electrochemiluminescence (ECL) system with the assistance of ionic liquids (ILs) was successfully established for sensitive determination of verticine and verticinone in Bulbus Fritillariae for the first time. Migration behavior of alkaloid largely relies on the hydrogen bonding interactions between alkyl imidazolium cations in ILs and the alkaloids. Running buffer containing 40 mmol/L 1-butyl-3-methylimidazolium tetrafluoroborate (BMImBF₄) IL-8 mmol/L phosphate resulted in significant changes in separation selectivity for alkaloids with similar structures. The highest sensitivity of the detection was obtained by maintaining the detection potential at 1.2 V. Under the optimized conditions, relative standard derivations of the ECL intensity and the migration time were 3.27 and 2.84% for verticine and 4.42 and 1.69% for verticinone, respectively. The standard curves were linear between 1 × 10⁻⁸ and 1 × 10⁻⁶ mol/L for verticine and between 5 × 10⁻⁸ and 1 × 10⁻⁶ mol/L for verticinone, respectively. Detection limits of 1.25 × 10⁻¹⁰ mol/L for verticine and 1 × 10⁻¹⁰ mol/L for verticinone were obtained (S/N = 3). Developed method was successfully applied to determine the amounts of alkaloids in Bulbus Fritillariae.     

Structure of N,C,N-chelated organotin(IV) fluorides

The set of starting tri-, di- and monoorganotin(IV) halides containing N,C,N-chelating ligand (L^NCN = {1,3-[(CH₃)₂NCH₂]₂C₆H₃}⁻) has been prepared (1-5) and two compounds structurally characterized ([L^NCNPh₂Sn]⁺I₃⁻ (1c), L^NCNSnBr₃ (5)) in the solid state. These compounds were reacted with KF with 18-crown-6, NH₄F or L^CNnBu₂SnF to give derivatives containing fluorine atom(s). Triorganotin(IV) fluorides L^NCNMe₂SnF (2a) and L^NCNnBu₂SnF (3a) revealed monomeric structural arrangement with covalent Sn-F bond both in the coordinating and non-coordinating solvents, except the behaviour of 3a that was ionized in the methanol solution at low temperature. The products of fluorination of L^NCNSnPhCl₂ (4) and 5 were described by NMR in solution as the ionic hypervalent fluorostannates or the oligomeric species reacting with chloroform, methanol or moisture to zwitterionic monomeric stannate L^NCN(H)⁺SnF₄⁻ (5c), which was confirmed by XRD analysis in the solid state.     

Development of a headspace-gas chromatography (HS-GC-PID-FID) method for the determination of VOCs in environmental aqueous matrices: Optimization, verification and elimination of matrix effect and VOC distribution on the Fortaleza Coast, Brazil

An analytical protocol combining a headspace technique with gas chromatography and detection by photoionization detector and flame ionization detector (HS-GC-PID-FID) was developed. This procedure was used to measure volatile organic compounds (VOCs) in environmental aqueous matrices and was applied in determination of VOCs on the coast of Fortaleza, Brazil. At optimum operating conditions, analytical figures of merit such as linearity (R ranged from 0.9983 to 0.9993), repeatability (5.62 to 9.63% and 0.02 to 0.19% for the quantitative and qualitative analyses, respectively), detection limits (0.22 to 7.48 μg L⁻¹) and sensibility were estimated. This protocol favors a fast sampling/sample preparation (in situ), minimizes the use of laboratory material, eliminates the matrix effect from environmental samples, and can be applied to river, estuarine and oceanic waters. The advantage of detectors in series is that a low sensitivity in detection in one is compensated by the other. Toluene was the most abundant VOC in the studied area, with an average concentration of 1.63 μg L⁻¹. It was followed by o-xylene (1.15 μg L⁻¹), trichloroethene (1.08 μg L⁻¹), benzene (0.86 μg L⁻¹), ethylbenzene (0.74 μg L⁻¹), carbon tetrachloride (0.55 μg L⁻¹), m/p-xylene (0.48 μg L⁻¹) and tetrachloroethene (0.46 μg L⁻¹), compounds which are very commonly detected in urban runoff from most cities. The results of the VOC distribution showed that port activity was not the main source of VOCs along the Fortaleza Coast, but that the contribution from urban runoff seemed more significant.     

Electrochemical behavior of hexafluoroniobate, heptafluorotungstate, and oxotetrafluorovanadate anions in N-butyl-N-methylpyrrolidinium bis(trifluoromethylsulfonyl)amide room temperature ionic liquid

Electrochemical behavior of hexafluoroniobate (Nb(V)F₆⁻), heptafluorotungstate (W(VI)F₇⁻), and oxotetrafluorovanadate (V(V)OF₄⁻) anions has been investigated in N-butyl-N-methylpyrrolidinium bis(trifluoromethylsulfonyl)amide (BMPyrTFSA) ionic liquid at 298 K by means of cyclic voltammetry and chronoamperometry. Cyclic voltammograms at a Pt electrode showed that Nb(V)F₆⁻ anion is reduced to Nb(IV)F₆²⁻ by a one-electron reversible reaction. Electrochemical reductions of W(VI)F₇⁻ and V(V)OF₄⁻ anions at a Pt electrode are quasi-reversible and irreversible reactions, respectively, according to cyclic voltammetry. The diffusion coefficients of Nb(V)F₆⁻, W(VI)F₇⁻ and V(V)OF₄⁻ determined by chronoamperometry are 1.34 × 10⁻⁷, 7.45 × 10⁻⁸ and 2.49 × 10⁻⁷ cm² s⁻¹, respectively. The Stokes radii of Nb(V)F₆⁻, W(VI)F₇⁻, and V(V)OF₄⁻ in BMPyrTFSA have been calculated to be 0.23, 0.38, and 0.12 nm, from the diffusion coefficients and viscosities obtained.     

Determination of free glycerol in biodiesel at a platinum oxide surface using potential cycling technique

A novel, inexpensive and fast method based on the electrooxidation of glycerol on platinum electrodes by the potential cycling technique has been designed for the determination of free glycerol in biodiesel. A wide range of linearity was achieved between 15 and 150 mg L⁻¹ (0.16 and 1.6 mmol L⁻¹), which corresponds to concentrations ranging between 56 and 560 mg kg⁻¹ (glycerol:biodiesel) for an extraction using 2 g biodiesel. A method for the fast extraction of glycerol from biodiesel with water followed by elimination of organic interferents has also been developed, so that the novel determination method can be applied to various biodiesel samples. The excellent repeatability allows determination of glycerol in numerous samples, with no need for recalibration.     

Ion-exchange chromatography using vanadyl and vandate salts as mobile phases with indirect detection

Summary Vanadyl sulfate, VOSO₄, was characterized as the mobile phase for the ion exchange separation of Li⁺, Na⁺, NH ₄ ⁺ , and K⁺ using indirect photometric detection at 254 nm. Detection limits ranged from 0.2 ppm for Li⁺ to 1 ppm for K⁺. Indirect electrochemical detection of these separated cations by reduction of VO (II) to V³⁺ was compared to spectrophotometric detection. The potential of the vanadate species, HVO ₄ ^2– , for the separation of F^–, Cl^–, and SO ₄ ^2– , with indirect photometric detection was also demonstrated.     

Silylating Agents Grafted onto Silica Derived from Leached Chrysotile

Silica from leached chrysotile fibers (SILO) was silanized with trialkoxyaminosilanes to yield inorganic–organic hybrids designated SILx (x=1–3). The greatest amounts of the immobilized agents were quantified as 2.14, 1.90, and 2.18 mmol g⁻¹ on SIL1, SIL2, and SIL3 for –(CH₂)₃NH₂,–(CH₂)₃NH(CH₂)₂NH₂, and –(CH₂)₃NH(CH₂)₂NH(CH₂)₂NH₂ groups attached to the inorganic support. The infrared spectra for all modified silicas showed the absence of the Si–OH deformation mode, originally found at 950 cm⁻¹, and the appearance of asymmetric and symmetric C–H stretching bands at 2950 and 2840 cm⁻¹. Other important bands associated with the organic moieties were assigned to ν_as(NH) at 3478 and ν_sym(NH) at 3418 cm⁻¹. The NMR spectrum of the solid precursor material suggested two different kinds of silicon atoms: silanol and siloxane groups, between −90 and 110 ppm; however, additional species of silicon that contain the organic moieties bonded to silicon at −58 and −66 ppm appeared after chemical modification. These modified silicas showed a high adsorption capacity for cobalt and copper cations in aqueous solution, in contrast to the original SILO matrix, confirming the unequivocal anchoring of silylating agents on the silica surface.     

Radiochemical characterization of spring waters in Balaton Upland, Hungary, estimation of radiation dose to members of public

Hungary is rich in spring waters. A survey studying the naturally occurring alpha emitter radionuclides in 30 frequently visited and regularly consumed spring waters was conducted out in the Balaton Upland region of Hungary.²²⁶Ra, ²²⁴Ra, ²³⁴U, ²³⁸U and ²¹⁰Po activity concentrations were determined by using alpha spectrometry after separation from matrix elements. Average concentration (mBq L^{− 1}) of ²²⁶Ra, ²²⁴Ra, ²³⁴U, ²³⁸U and ²¹⁰Po in the spring waters is varied from 2.1 to 601, from < 1.1 to 65.4, from 3.9 to 741.9, from < 0.44 to 274.3 and from 2 to 15.2 respectively. In most cases radioactive disequilibrium was observed between uranium and radium isotopes. The doses for the analyzed samples of spring water are in the range 3.59–166.73 μSv y^{− 1} with an average 18.2 μSv y^{− 1} .This is well below the 100 μSv y^{− 1} reference level of the committed effective dose recommended by WHO. Only one water sample had a dose higher than 100 μSv y^{− 1}, mainly due to the contribution from radium (²²⁶Ra, ²²⁴Ra) and ²¹⁰Po isotopes. This study provides important information for consumers and authorities about their internal radiological exposure risk from spring water intake.     

Simultaneous capillary electrophoretic determination of Sb(III) and Bi(III) based on the complex-formation with a W(VI)-P(V) reagent

A capillary electrophoretic method was developed for the simultaneous determination of Sb(III) and Bi(III). A 1.0 mM W(VI)-0.10 mM P(V) complexing reagent readily reacted with a mixture of trace amounts of Sb(III) and Bi(III) to form the corresponding ternary Keggin-type complexes; [P(Sb^IIIW₁₁)O₄₀]⁶⁻ and [P(Bi^IIIW₁₁)O₄₀]⁶⁻ in 0.01 M malonate buffer (pH 2.4). Since the peaks due to the migrations of the ternary complex anions were well separated in the electropherogram, the pre-column complex-formation reaction was applied to the simultaneous CE determination of Sb(III) and Bi(III) with direct UV detection at 255 nm. The calibration curves were linear in the range of 2×10⁻⁷-5×10⁻⁵ M; a detection limit of 1×10⁻⁷ M was achieved for Sb(III) or Bi(III) (the signal-to-noise ratio=3).     

Evaluation of tris(4,7-diphenyl-1,10-phenanthrolinedisulfonate)ruthenium(II) as a chemiluminescence reagent

Previous studies have suggested that tris(4,7-diphenyl-1,10-phenanthrolinedisulfonate)ruthenium(II) (Ru(BPS)₃⁴⁻) has great potential as a chemiluminescence reagent in acidic aqueous solution. We have evaluated four different samples of this reagent (two commercially available and two synthesised in our laboratory) in comparison with tris(2,2′-bipyridine)ruthenium(II) (Ru(bipy)₃²⁺) and tris(1,10-phenanthroline)ruthenium(II) (Ru(phen)₃²⁺), using a range of structurally diverse analytes. In general, Ru(BPS)₃⁴⁻ produced more intense chemiluminescence, but the oxidised Ru(BPS)₃³⁻ species is less stable in aqueous solution than Ru(bipy)₃³⁺ and produced a greater blank signal than Ru(bipy)₃³⁺ or Ru(phen)₃³⁺, which had a detrimental effect on sensitivity. Although the complex is often depicted with the sulfonate groups of the BPS ligand in the para position on the phenyl rings, NMR characterisation revealed that the commercially available BPS material used in this study was predominantly the meta isomer.     

Improving the sensitivity of the determination of ceftiofur by capillary electrophoresis in environmental water samples: in-line solid phase extraction and sample stacking techniques

This paper describes two different approaches for increasing the sensitivity for the analysis of ceftiofur by capillary electrophoresis (CE). Two different techniques based on the introduction of an enlarged volume of sample, namely large volume sample stacking (LVSS) and in-line solid phase extraction (SPE) were studied and compared. LVSS allowed the on-column electrophoretic preconcentration of ceftiofur without modification of the separation capillary. In-line SPE-CE was developed by using a home-made microcartridge that was filled with a reversed-phase sorbent (C₁₈). The microcartridge was coupled in-line near the inlet of the separation capillary. LVSS and in-line SPE-CE allowed automated operation and improved sensitivity for the analysis of ceftiofur with respect to conventional CE. When environmental water samples were analyzed, an additional pretreatment step based on off-line SPE was necessary in both cases to further decrease the detection limits. In terms of sensitivity for the determination of ceftiofur in river water samples, the combination of off-line SPE with in-line SPE-CE was found the most sensitive with a detection limit of 10 ng L⁻¹, whereas the method based on the use of off-line SPE with LVSS presented a detection limit of 100 ng L⁻¹.     

Simultaneous determination of free and total glycerol in biodiesel by capillary electrophoresis using multiple short‐end injection

A rapid method for the simultaneous determination of free glycerol (FG) and total glycerol (TG) in biodiesel by CE using a short‐end multiple injection (SE/MI) configuration system is described. The sample preparation for FG involves the extraction of glycerol with water and for TG a saponification reaction is carried out followed by extraction as in the case of FG. The glycerol extracted in both cases is submitted to periodate oxidation and the iodate ions formed are measured on a CE‐SE/MI system. The relevance of this study lies in the fact that no analytical procedure has been previously reported for the determination of TG (or of FG and TG simultaneously) by CE. The optimum conditions for the saponification/extraction process were 1.25% KOH and 25°C, with a time of only 5 min, and biodiesel mass in the range of 50.0–200.0 mg can be used. Multiple injections were performed hydrodynamically with negative pressure as follows: 50 mbar/3s (FG sample); 50 mbar/6s (electrolyte spacer); 50 mbar/3s (TG sample). The linear range obtained was 1.55–46.5 mg/L with R²> 0.99. The LOD and LOQ were 0.16 mg/L and 0.47 mg/L, respectively for TG. The method provides acceptable throughput for application in quality control and monitoring biodiesel synthesis process. In addition, it offers simple sample preparation (saponification process), it can be applied to a variety biodiesel samples (soybean, castor, and waste cooking oils) and it can be used for the determination of two key parameters related to the biodiesel quality with a fast separation (less than 30 s) using an optimized CE‐SE/MI system.     

Rapid determination of acetaminophen and p-aminophenol in pharmaceutical formulations using miniaturized capillary electrophoresis with amperometric detection

Capability of fast analysis of a novel miniaturized capillary electrophoresis with carbon disk electrode amperometric detection (mini-CE-AD) system was demonstrated by determining acetaminophen and p-aminophenol in dosage forms. Factors influencing the separation and detection processes were examined and optimized. Under the optimum conditions, the end-capillary 300 μm carbon disc electrode amperometric detector offered favorable signal-to-noise characteristics at a relatively low potential (+600 mV versus Ag/AgCl) for detecting acetaminophen and p-aminophenol. Two analytes can been separated within 150 s in a 8.5 cm length capillary at a separation voltage of 2000 V using a Na₂B₄O₇-KH₂PO₄ running buffer (pH 7.2). Acetaminophen and p-aminophenol could be detected down to the 1.4 × 10⁻⁶-5.9 × 10⁻⁷ mol L⁻¹ level with linearity up to the 1.0 × 10⁻³ mol L⁻¹ level examined. The inter-day repeatability for analytes in peak current (R.S.D. ≤ 2.3%) and migration times (R.S.D. ≤ 1.3%) were excellent. The proposed mini-CE-AD system should find a wide range of analytical applications in pharmaceutical formulations as an alternative to conventional CE and μ-CE.     

Ultra-sensitive DNA assay based on single-molecule detection coupled with fluorescent quantum dot-labeling and its application to determination of messenger RNA

Rapid, inexpensive, and convenient methods for quantifying elemental sulfur (S⁰) with low or sub-μg g⁻¹ limits of detection would be useful for a range of applications where S⁰ can act as a precursor for noxious off-aromas, e.g., S⁰ in pesticide residues on winegrapes or as a contaminant in drywall. However, existing quantification methods rely on toxic reagents, expensive and cumbersome equipment, or demonstrate poor selectivity. We have developed and optimized an inexpensive, rapid method (∼15 min per sample) for quantifying S⁰ in complex matrices. Following dispersion of the sample in PEG-400 and buffering, S⁰ is quantitatively reduced to H₂S in situ by dithiothreitol and simultaneously quantified by commercially available colorimetric H₂S detection tubes. By employing multiple tubes, the method demonstrated linearity from 0.03 to 100 μg S⁰ g⁻¹ for a 5 g sample (R² = 0.994, mean CV = 6.4%), and the methodological detection limit was 0.01 μg S⁰ g⁻¹. Interferences from sulfite or sulfate were not observed. Mean recovery of an S⁰ containing sulfur fungicide in grape macerate was 84.7% with a mean CV of 10.4%. Mean recovery of S⁰ in a colloidal sulfur preparation from a drywall matrix was 106.6% with a mean CV of 6.9%. Comparable methodological detection limits, sensitivity, and recoveries were achieved in grape juice, grape macerate and with 1 g drywall samples, indicating that the methodology should be robust across a range of complex matrices.