H2O2-photosensitized emulsion copolymerization of tetrafluoroethylene with propylene

The H₂O₂-photosensitized emulsion copolymerization of tetrafluoroethylene with propylene was carried out at room temperature in the presence of gaseous monomers of 50 mole-% tetrafluoroethylene content. The conversion increased almost linearly with irradiation time. The rate of polymerization was proportional to the 1.0 power of H₂O₂ concentration up to 3.5 × 10^?3M H₂O₂ and the 0.46 power of H₂O₂ concentration above 3.5 × 10^?3M H₂O₂. The result obtained at low H₂O₂ concentration was almost consistent with that obtained in the radiation-induced method. The rate of polymerization was proportional to the 0.58 power of the emulsifier concentration, and the degree of polymerization was independent of the emulsifier concentration. The H₂O₂-photosensitized emulsion copolymerization of tetrafluoroethylene with propylene is terminated mainly by degradative chain transfer of the propagating radical to propylene at low H₂O₂ concentration and by the reaction of the propagating radical with OH radical from photolysis of H₂O₂–aqueous solution at high H₂O₂ concentration.     

Cyclization of diols with ammonia over CuO-ZnO-Al2O3 catalyst in the presence of H2

Cyclization of diols with ammonia in an H₂ atmosphere over an industrial CuO-ZnO-Al₂O₃ catalyst for the synthesis of methanol (SNM-1) gives nitrogen-containing five-, six-, or seven-membered heterocyclic compounds. The yields of cyclic amines in the 180–230 °C temperature range are 46 to 97 %.Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 10, pp. 2046–2048, October, 1995.     

Investigations on the kinetics of copolymerization of vinyl acetate with acrylonitrile by Co(acac)3–Al(C2H5)3 catalyst system

Vinyl acetate and acrylonitrile were copolymerized with Co(acac)₃-Al(C₂H₅)₃ catalyst system in benzene at 40°C. The rate of copolymerization is linearly proportional to monomer concentration and catalyst concentrations up to a certain value. The overall activation energy was found to be 11.3 kcal/mole. The effect of hydroquinone on the rate of copolymerization indicates the presence of free radicals in this system. The possibility of simultaneous formation of coordinate anionic and free radical active sites has been proposed.     

Perfectly alternating copolymerization of CO2 and epichlorohydrin using cobalt(III)-based catalyst systems

Selective transformations of carbon dioxide and epoxides into biodegradable polycarbonates by the alternating copolymerization of the two monomers represent some of the most well-studied and innovative technologies for potential large-scale utilization of carbon dioxide in chemical synthesis. For the most part, previous studies of these processes have focused on the use of aliphatic terminal epoxides or cyclohexene oxide derivatives, with only rare reports concerning the synthesis of CO(2) copolymers from epoxides containing electron-withdrawing groups such as styrene oxide. Herein we report the production of the CO(2) copolymer with more than 99% carbonate linkages from the coupling of CO(2) with epichlorohydrin, employing binary and bifunctional (salen)cobalt(III)-based catalyst systems. Comparative kinetic studies were performed via in situ infrared measurements as a function of temperature to assess the activation barriers for the production of cyclic carbonate versus copolymer involving two electronically different epoxides: epichlorohydrin and propylene oxide. The relative small activation energy difference between copolymer versus cyclic carbonate formation for the epichlorohydrin/CO(2) process (45.4 kJ/mol) accounts in part for the selective synthesis of copolymer to be more difficult in comparison with the propylene oxide/CO(2) case (53.5 kJ/mol). Direct observation of the propagating polymer-chain species from the binary (salen)CoX/MTBD (X = 2,4-dinitrophenoxide and MTBD = 7-methyl-1,5,7-triazabicyclo[4.4.0]dec-5-ene) catalyst system by means of electrospray ionization mass spectrometry confirmed the perfectly alternating nature of the copolymerization process. This observation in combination with control experiments suggests possible intermediates involving MTBD in the CO(2)/epichlorohydrin copolymerization process.     

Magnetically separable polyoxometalate catalyst for the oxidation of dibenzothiophene with H2O2

Two types of polyoxometalate-functionalized magnetic nanoparticles catalysts consisting of H(3)PW(12)O(40) supported on surface-modified Fe(3)O(4) magnetite nanoparticles were prepared using an easy synthetic route and successfully applied for the oxidation of dibenzothiophene. The magnetic catalysts showed a catalytic performance in the oxidation of dibenzothiophene in acetonitrile with hydrogen peroxide, and high conversions were obtained. The catalysts could be easily separated from the reaction solution by applying an external magnetic field and recycled several times.     

Deuterium exchange in the systems of H2O+/H2O and H3O+/H2O

The reactions of H₂O⁺, H₃O⁺, D₂O⁺, and D₃O⁺ with neutral H₂O and D₂O were studied by tandem mass spectrometry. The H₂O⁺ and D₂O⁺ ion reactions exhibited multiple channels, including charge transfer, proton transfer (or hydrogen atom abstraction), and isotopic exchange. The H₃O⁺ and D₃O⁺ ion reactions exhibited only isotope exchange. The variation in the abundances of all ions involved in the reactions was measured over a neutral pressure range from 0 to 2 × 10⁻⁵ Torr. A reaction scheme was chosen, which consisted of a sequence of charge transfer, proton transfer, and isotopic exchange reactions. Exact solutions to two groups of simultaneous differential equations were determined; one group started with the reaction of ionized water, and the other group started with the reactions of protonated water. A nonlinear least-squares regression technique was used to determine the rate coefficients of the individual reactions in the schemes from the ion abundance data. Branching ratios and relative rate coefficients were also determined in this manner.A delta chi-squared analysis of the results of the model fitted to the experimental data indicated that the kinetic information about the primary isotopic exchange processes is statistically the most significant. The errors in the derived values of the kinetic information of subsequent channels increased rapidly. Data from previously published selected ion flow tube (SIFT) study were analyzed in the same manner. Rigorous statistical analysis showed that the statistical isotope scrambling model was unable to explain either the SIFT or the tandem mass spectrometry data. This study shows that statistical analysis can be utilized to assess the validity of possible models in explaining experimentally observed kinetic behaviors.     

ZrO2、Y2O3对CH4燃烧催化剂Fe2O3/γ-Al2O3的改性作用

γ-Ａｌ2Ｏ3作为催化剂载体具有较大的比表面积,机械强度高,孔结构适宜,但不耐高温。近年来,氧化锆载体以其耐高温等[1]独特性质引起多方面的关注[2-4],它能与所负载的金属产生强烈的电子相互作用,影响催化剂的吸附、氧化和还原性能。但是ＺｒＯ2比表面积较小,且随焙烧温度的升高急剧下降,如单独作为催化剂载体,其应用受到很大限制。若将ＺｒＯ2分散到γ-Ａｌ2Ｏ3表面上,可制得兼备两者优点的复合载体。当ＺｒＯ2中加入Ｙ2Ｏ3,能产生特殊的氧空穴[5],具有氧离子传导功能和导电性;与活性组分相结合能在很大程度上提高反应速度。我们用Ｙ…     

Influence of addition of ethylene on the γ-ray-induced alternating copolymerization of ethylenimine and carbon monoxide

The influence of the addition of ethylene on the γ-ray-induced alternating copolymerization of ethylenimine and carbon monoxide was investigated. A mixture of ethylenimine, carbon monoxide, and ethylene was irradiated to produce a polymer containing these monomeric units. The infrared spectrum of the copolymer showed the characteristic absorption peaks of the secondary amide and ketone bond and was different from that of the reaction product of polyketone with ethylenimine and that of the γ-ray irradiation product of ethylene and poly-ß-alanine. The x-ray diffraction diagram of the copolymer was different from those of poly-ß-alanine and polyketone and exhibited an amorphous structure. Paper chromatographic analysis showed that the hydrolysis product of the copolymer contained ß-alanine and δ-aminovaleric acid. These results indicate that terpolymerization of ethylenimine, carbon monoxide, and ethylene took place under γ-ray irradiation and gave an amorphous polymer containing the units \documentclass{article}\pagestyle{empty}\begin{document}$ \rlap{} ({\rm CH}_{\rm 2} {\rm CH}_{\rm 2} {\rm NHCO}\rlap{}),\rlap{} ({\rm CH}_{\rm 2} {\rm CH}_{\rm 2} {\rm CO}\rlap{}),{\rm and}\rlap{} ({\rm CH}_{\rm 2} {\rm CH}_{\rm 2} {\rm CH}_{\rm 2} {\rm CH}_{\rm 2} {\rm NHCO}\rlap{}) $\end{document}     

Anionic polymerization of methyl methacrylate with Cr(C5H7O2)3–Al(C2H5)3 catalyst system

A homogeneous catalyst system, Cr(C₅H₇O₂)₃–Al(C₂H₅)₃, was used for the polymerization of methyl methacrylate. The yield of polymer increased up to an Al/Cr ratio of 12 and thereafter remained almost constant with increasing Al/Cr. The rate of polymerization increased linearly with increasing catalyst and monomer concentrations at Al/Cr = 12. The molecular weight, however, decreased with increasing catalyst concentration and increased with increasing monomer concentration, indicating anionic polymerization reaction. NMR studies of the polymers indicated the presence of a stereoblock structure, which changed to heteroblock structure in presence of triethylamine and hydroquinone as additives in the catalyst. In the light of these observations, the mechanism of the polymerization is discussed.     

H2-induced CO adsorption and dissociation over Co/Al2O3 catalyst

The activation of adsorbed CO is an important step in CO hydrogenation. The results from TPSR of pre-adsorbed CO with H2 and syngas suggested that the presence of H2 increased the amount of CO adsorption and accelerated CO dissociation. The H2 was adsorbed first, and activated to form H＊ over metal sites, then reacted with carbonaceous species. The oxygen species for CO2 formation in the presence of hydrogen was mostly OH^＊, which reacted with adsorbed CO subsequently via CO^＊＋OH^＊ → CO2^＊＋H^＊; however, the direct CO dissociation was not excluded in CO hydrogenation. The dissociation of C-O bond in the presence of H2 proceeded by a concerted mechanism, which assisted the Boudourd reaction of adsorbed CO on the surface via CO^＊＋2H^＊ → CH^＊＋OH^＊. The formation of the surface species （CH） from adsorbed CO proceeded as indicated with the participation of surface hydrogen, was favored in the initial step of the Fischer-Tropsch synthesis.     

H2-induced CO adsorption and dissociation over Co/Al2O3 catalyst

The activation of adsorbed CO is an important step in CO hydrogenation. The results from TPSR of pre-adsorbed CO with H2 and syngas suggested that the presence of H2 increased the amount of CO adsorption and accelerated CO dissocia-tion. The H2 was adsorbed first, and activated to form H* over metal sites, then reacted with carbonaceous species. The oxygen species for CO2 formation in the presence of hydrogen was mostly OH*, which reacted with adsorbed CO subsequently via CO*+OH* → CO2*+H*; however, the direct CO dissociation was not excluded in CO hydrogenation. The dissociation of C-O bond in the presence of H2 proceeded by a concerted mechanism, which assisted the Boudourd reaction of adsorbed CO onthe surface via CO*+2H* → CH*+OH*. The formation of the surface species (CH) from adsorbed CO proceeded as indicated with the participation of surface hydrogen, was favored in the initial step of the Fischer-Tropsch synthesis.     

New information on the alternating copolymerization of butadiene-1,3 with acrylonitrile

Butadiene-1,3 and acrylonitrile were copolymerized by alkylaluminum halides alone or, more effectively, by the alkylaluminum halide/vanadium compound systems, into an alternating copolymer in which the butadiene units are linked predominantly in the trans-1,4 configuration. The efficiency of the aluminum components in the latter catalyst systems appear to decrease in the following order: AlEtCl₂ > Al₂Et₃Cl₃ ? AlEt₂Cl(?AlCl₃). The alkylaluminum halides could also be used effectually in the form of the complex with acrylonitrile. The catalytic activity was markedly affected by the order of mixing of the catalyst components and the monomers. Effective catalysts could be prepared only when the catalyst components were mixed in the presence of acrylonitrile. The catalyst activity was also found to depend upon the Al/V ratio, reaching its maximum when the ratio was about 20 in the AlEtCl₂·AN/VO(Ot-Bu)₃ system. Other combinations of conjugated diene with conjugated polar vinyl monomer were similarly copolymerized by these catalysts. It was found that different feed ratios between the diene and the vinyl monomer which were varied over a wide range always resulted in the formation of a 1:1 copolymer. The butadiene-acrylonitrile copolymer thus formed gave an NMR spectrum in which there was only one peak assignable to the methylene protons (7.72 τ) of the butadiene unit. On the basis of these findings, it may be suggested that alternating copolymerization prevails in the polymerization systems here investigated.     

Equation of state for the NH3−H2O system

An equation of state (EOS) for the NH₃–H₂O system has been developed. This EOS incorporates a highly accurate end-member EOS and on an empirical mixing rule. The mixing rule is based on an analogy with high order contributions to the virial expansion for mixtures. Comparison with experimental data indicates that the mixed system EOS can predict both phase equilibria and volumetric properties for this binary system with accuracy close to that of the experimental data from 50°C and 1 bar to critical temperatures and pressures.     

Oxidation of furfural with H2O2 in the presence of a photogenerated iron catalyst

Visible irradiation of a methanolic solution of furfural containing dilute aqueous H₂O₂ and [FeCp(C₆H₅R)]PF₆ (1: R  H, Cl or CH₃) as catalyst yields methyl 2-furoate quantitatively. After photodecomplexation, the inorganic Fe^II,III catalyst can be isolated and recycled several times with unchanged activity in dark reactions at 20°C.     

Ind2Zr(OC6H4Me-P)2和EtnAICL3-n催化乙烯齐聚的研究

茂金属催化剂 ( Kaminsky催化剂 )是 80年代发展起来的烯烃聚合高效催化剂 [1] ,有关其催化烯烃聚合的研究很多 [2～ 4 ] .近年来 ,Kaminsky型催化剂催化乙烯齐聚合成低碳α烯烃的研究已有报道 [5] .由乙烯齐聚得到的直链低碳α烯烃是生产线性低密度聚乙烯 ( LL DPE)和高密度聚乙烯 ( HDPE)的共聚单体 .以茚基锆化合物与烷基铝组成的 Ziegler- Natta催化体系催化乙烯齐聚尚未见报道 .本文考察了Ind2 Zr( OC6H4 Me- p) 2 和各种乙基铝组成的二元催化体系对乙烯齐聚的催化性能 .1　实验部分　　二茚基锆配合物 Ind2 Zr Cl2 和 Ind2 …     

A study of the graft copolymerization of methacrylic acid onto starch using the H2O2/Fe++ redox system

Graft copolymerization of methacrylic acid (MetAc) onto potato starch using H₂O₂/Fe⁺⁺ redox system was investigated. The best conditions of the grafting reaction were determined and several variables were studied: initiator and monomer concentrations, time, and temperature. Percent grafting efficiency, percent grafting, percent grafted monomer conversion, and total conversion were obtained. The optimum graft yield was obtained at 7.3 × 10^?3M H₂O₂ concentration and it was favored by increasing the methacrylic acid concentration and reaction time.