A Metastable Crystalline Phase in Two‐Dimensional Metallic Oxide Nanoplates

A simple method was adopted in which ultrathin cerium oxide nanoplates (<1.4 nm) were synthesized to increase the surface atomic content, allowing transformation from a face‐centered cubic (fcc) phase to a body‐centered tetragonal (bct) phase. Three types of cerium oxide nanoparticles of different thicknesses (1.2 nm ultrathin nanoplates, 2.2 nm nanoplates, and 5.4 nm nanocubes) were examined using transmission electron microscopy and X‐ray diffraction. The metastable bct phase was observed only in ultrathin nanoplates. Thermodynamic energy analysis confirmed that the surface energy of the ultrathin nanoplates is the cause of the remarkable stabilization of the metastable bct phase. The mechanism of surface energy regulation can be expanded to other metallic oxides, thus providing a new means for manipulating and stabilizing novel materials under ambient conditions that otherwise would not be recovered.     

Green, effective chemical route for the synthesis of silver nanoplates in tannic acid aqueous solution

Silver nanoplates, with average size tunable from 50 to 500 nm, have been synthesized via a simple room-temperature tannic acid (TA) solution-phase chemical reduction method. The synthesis was a seedless process in which tannic acid was used as a reducing as well as a capping agent, and did not need any other surfactant or capping agent to direct the anisotropic growth of the silver nanoparticles. The morphology of silver nanoplates has been confirmed by transmission electron microscopy, the growth process of nanoplates has been studied by UV/vis spectroscopy. Control experiments have been explored for a more thorough understanding of the growth mechanism. It was found that both the concentrations of TA and the pH of solution were the key elements to control the morphology silver nanoplates. The optical in-plane dipole plasmon resonance bands of these silver plates could be tuned from 520 to 1100 nm.     

Silver nanoplates: a highly sensitive material toward inorganic anions

This paper demonstrates a simple sensing method to detect inorganic anions by silver nanoplates (edge length of approximately 70 nm and thickness of approximately 2 nm) in aqueous solution. By this method, the solution system containing silver nanoplates shows a high sensitivity on the order of 1 x 10(-6) M in detecting halides, phosphate, and thiocyanate ions in water at room temperature. The sensitivity could be identified by the shift in the surface plasmon resonance (SPR) band in UV-vis spectrum. The selectivity of such a sensing system toward various anions was also studied, and it was found that this sensing system could distinguish individual anions (e.g., Cl-, Br-, I-, H2PO4-, and SCN-) from other anions (e.g., F-, SO42-, CH3COO-, NO3-, and ClO4-) and inorganic cations (e.g., Zn2+, Cd2+, and Cu2+) under the given conditions. The sensing mechanism was also analyzed. It was proposed that the particle surface electron charging, which is mainly determined by the interaction tendency between silver atoms and various inorganic anions in water, is responsible for the shift in the SPR observed. The need for further studies was finally discussed, particularly for systems composed of mixed anions.     

Temperature-controlled growth of ZnO nanowires and nanoplates in the temperature range 250-300 degrees C

Starting from a mixture of Zn and BiI3, we grew nanowires and nanoplates on an oxidized Si substrate at relatively low temperatures of 250 and 300 degrees C, respectively. The ZnO nanowires had diameters of approximately 40 nm and grew along the [110] direction rather than the conventional [0001] direction. The nanoplates had thicknesses of approximately 40 nm and lateral dimensions of 3-4 microm. The growth of both the nanowires and nanoplates is dominated by the synergy of vapor-liquid-solid (VLS) and direction conducting. Analysis of photoluminescence spectra suggested that the nanoplates contain more oxygen vacancies and have higher surface-to-volume ratios than the nanowires. The present results clearly demonstrate that the shapes of ZnO nanostructures formed by using BiI3 can be controlled by varying the temperature in the range 250-300 degrees C.     

Optimization of synthesis procedure and structure characterization of manganese tungstate nanoplates

A simple and fast chemical method was used for synthesis of manganese tungstate nanoplates in flower-like clusters; while Taguchi robust design was employed as statistical method for optimization of the experimental parameters for the procedure. Ultrafine manganese tungstate plates in flower-like clusters were synthesized via a direct precipitation method involving addition of manganese ion solution to the aqueous tungstate reagent. Effects of various reaction conditions such as manganese and tungstate concentrations, flow rate of reagent addition and reactor temperature on the thickness of the synthesized manganese tungstate plates were investigated experimentally. Analysis of variance (ANOVA) showed that manganese tungstate nanoplates could be effectively synthesized by tuning significant parameters of precipitation procedure. Meanwhile, optimum conditions for synthesis of MnWO4 nanoplates via this simple, fast, and cost effective method were proposed. The structure and composition of the prepared nanoplates under optimum conditions were characterized by EDX, X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), FT-IR spectroscopy, and photoluminescence techniques.      

Facile synthesis and catalytic property of porous tin dioxide nanostructures

Porous tin dioxide (SnO(2)) nanostructures consisting of nanoplates are prepared through thermal decomposition of the mixed solution composed of dibutyltin dilaurate and acetic acid. The aggregations of the nanoplates give rise to large macropores with the size of about 100-300 nm. These nanoplates have a wormhole-like porous structure with the size of about 4 nm and possess high surface area. X-ray powder diffraction, transmission electron microscopy, scanning electron microscopy, infrared spectroscopy, and nitrogen sorption have been employed to characterize the obtained porous structures. It is found that the obtained nanostructures exhibit excellent catalytic activity toward methanol decomposition. Such porous structures with high surface area have promising industrial applications as catalysts.     

Synthesis of CeVO<Subscript>4</Subscript> Crystals with Different Sizes and Shapes

Tetragonal CeVO₄ was prepared through hydrothermal treatment and sonication method with the same precursor in the absence of any catalysts or templates, and the products were characterized by XRD, TEM and Raman. It is found that microrods, nanoparticles, nanorods and nanoplates have been obtained. The bigger nanorods produced through hydrothermal treatment have average diameters of 15–25 nm and lengths of 20–60 nm. The smaller nanorods prepared through ultrasound treatment have average diameters of 6–12 nm and lengths of 10–18 nm. Uniform nanoplates have been produced. The nanoplates produced through hydrothermal method are composed of CeVO₄ and CeO₂. The mechanism of shape changing has been discussed. And the existing vanadium which is sensitive to the pH value of synthesis solution may be a key factor for the resulted sizes and shapes of the obtained nanocrystals. The samples prepared through hydrothermal treatment and sonication method were used as the catalysts for the combustion of trichloroethylene to test their catalytic activity.     

Synthesis and Characterization of β‐Co(OH)2, CuO and ZnO Nanostructures by Solvothermal Method without Any Additive

β‐Co(OH)₂, CuO and ZnO nanostructures with plate‐like, particle‐like and flower‐like morphologies were prepared through the use of simple solvothermal method using of melt salt and 1,10‐phenanthroline as complexing agent and sodium hydroxide. β‐Co(OH)₂ consisted of a plate‐like structure, and the nanoplates size was about 29 nm. The structure was comprised of regular sheets which were assembled together. Furthermore, the as‐obtained β‐Co(OH)₂ nanoplates can be easily converted into Co₃O₄ nanoplates by calcining in air at 500 °C for 2 h. The results indicate that ZnO powder is of hexagonal wurtzite structure and well crystallized with high purity. CuO powder is pure monoclinic‐structured crystalline. The products were characterized by X‐ray diffraction (XRD), scanning electron microscopy (SEM), and Fourier transform infrared (FT‐IR) spectra. Possible formation mechanism of the nanostructures is proposed.     

Oxidants for the colorimetric determination of pindolol

A simple, sensitive and accurate colorimetric method is described for the quantitative determination of pindolol either in the pure form or in its tablets. The method is based on the oxidation of the indole moiety in pindolol with potassium persulphate or hydrogen peroxide-in acid medium-to give a highly coloured product that exhibits maximum absorption at 535 nm and 570 nm, respectively. Beer's law is obeyed over concentrations ranging from 0.07-0.35 mg/10 ml for potassium persulphate and 0.1-0.5 mg/10 ml for hydrogen peroxide with mean recoveries of 99.6+/-0.6 and 99.8+/-0.9%, respectively. The method is applied for the assay of pindolol tablets without any interference due to tablet fillers.     

烟草花叶病毒介导合成三角形金纳米片

利用碱处理烟草花叶病毒的生物还原性和辅助结构导向作用,在室温下以水为溶剂直接还原氯金酸制备出三角形金纳米片。采取透射电子显微镜（TEM）、高分辨透射电子显微镜（HRTEM）、选区电子衍射（SAED）和紫外-可见光谱仪（UV-Vis）等对所制备金纳米片的结构和性能进行了表征。结果显示,所制备三角形金纳米片为单晶,三角面为{111}晶面簇,边长在40 ~120 nm之间,厚度约为15 nm。该材料在可见光区有两个等离子共振吸收峰,在感光成像、生物检测和催化等领域具有很好的应用前景。     

Mesoporous rare earth fluoride nanocrystals and their photoluminescence properties

YF(3) and YF(3):Eu(3+) mesoporous hexagonal nanocrystals were successfully synthesized via a simple hydrothermal process based on the in situ assembly of the as-synthesized YF(3) and YF(3):Eu(3+) nanoparticles. The well defined mesoporous nanostructures are formed by phenanthroline assisted assembly of ～20 nm nanoparticles, and 2-4 nm pores are contained as indicated by N(2) adsorption-desorption studies. The obtained YF(3):Eu(3+) mesoporous hexagonal nanoplates show a significant photoluminescence intensity enhancement compared with other shaped YF(3):Eu(3+) nanocrystals.     

Simultaneous determination of hyoscine butylbromide and ketoprofen in pharmaceutical preparations by spectrophotometric and liquid chromatographic methods

A binary mixture of hyoscine butylbromide and ketoprofen was determined by 4 different methods. The first involved determination of hyoscine butylbromide and ketoprofen using the ratio-spectra first-derivative spectrophotometric technique at 211 and 234 nm over the concentration ranges of 2-14 and 5-45 microg/mL with mean accuracies 99.84 +/-0.92 and 99.98+/- 0.64%, respectively. The second method utilized second-derivative spectrophotometry over the concentration ranges of 2-14 and 5-35 microg/mL with mean accuracies 99.32+/- 1.06 and 99.55+/-1.15%, respectively. The third method was based on the resolution of the 2 components by bivariate calibration depending on a simple and rapid mathematical algorithm and quantitative evaluation of the absorbances at 206 and 254 nm over concentration ranges of 2-16 and 5-35 microg/mL; mean accuracies of 100.21+/-1.30 and 100.19 +/-1.07% were obtained for hyoscine butylbromide and ketoprofen, respectively. The fourth method was reversed-phase liquid chromatography using 0.05 M ammonium dihydrogen phosphate-acetonitrile-methanol (20 + 30 + 6, v/v) as the mobile phase with ultraviolet detection at 220 nm over concentration ranges of 1-90 and 5-70 microg/mL; mean accuracies were 99.92+/-1.02 and 99.61+/- 0.98%, respectively. The suggested procedures were checked using laboratory-prepared mixtures and were successfully applied for the analysis of pharmaceutical preparations. The methods retained their accuracy and precision when the standard addition technique was applied. The results obtained by applying the proposed methods were statistically analyzed and compared with those obtained by the manufacturer's method.     

New methods for determination of cinnarizine in mixture with piracetam by spectrodensitometry, spectrophotometry, and liquid chromatography

Four new methods were developed and validated for the determination of cinnarizine HCl in its binary mixture with piracetam in pure and pharmaceutical preparations. The first one was a densitometric analysis that provides a simple and rapid method for the separation and quantification of cinnarizine HCI. The method depends on the quantitative densitometric evaluation of thin-layer chromatograms of cinnarizine HCI at 252 nm over concentration range of 1-6 microg/spot, with a mean accuracy of 100.05 +/- 0.91%. The second method was determination of the drug using a colorimetric method that utilizes the reaction of 3-methyl-benzothiazolin-2-one in the presence of FeCl3 as an oxidant. The green color of the resulting product was measured at 630 nm over concentration range 10-40 microg/mL, with a mean accuracy of 100.10 +/- 1.13%. The third method was a direct spectrophotometric determination of cinnarizine HCI at 252 nm over the concentration range 7-20 microg/mL, while piracetam was determined by derivative ratio spectrophotometry at 221.6 nm over concentration range 5-30 microg/mL, with a mean accuracy of 100.14 +/- 0.79 and 100.26 +/- 1.24% for cinnarizine HCI and piracetam, respectively. The last method was a liquid chromatography analysis of both cinnarizine HCI and piracetam, depending on quantitative evaluation of chromatograms of cinnarizine HCI and piracetam at 252 and 212 nm, respectively, over the concentration range 10-200 microg/mL for cinnarizine HCI and 20-500 microg/mL for piracetam, with a mean accuracy of 100.03 +/- 0.89 and 100.40 +/- 0.94% for cinnarizine HCI and piracetam, respectively. The proposed procedures were checked using laboratory-prepared mixtures and successfully applied for the analysis of their pharmaceutical preparations. The validity of the proposed procedures was further assessed by applying the standard addition technique. Recoveries were quantitative, and the results obtained agreed with those obtained by other reported methods.     

Thermal aqueous solution approach for the synthesis of triangular and hexagonal gold nanoplates with three different size ranges

The synthesis of gold nanoplates was carried out in an aqueous solution by thermal reduction of HAuCl(4) with trisodium citrate in the presence of cetyltrimethylammonium bromide (CTAB) surfactant in just 5-40 min. The sizes of the gold nanoplates can be varied from as small as tens of nanometers in width, to several hundreds of nanometers, and even a few microns in width by changing the reagent concentrations, solution temperature, and the reaction time. A [CTAB]/[HAuCl(4)] ratio of 6 in the reaction solution was found to be favorable for the formation of gold nanoplates. The nanoplates possess well-defined shapes with sharp edges. The small nanoplates exhibit mainly a triangular shape, while larger nanoplates show a mixture of triangular, hexagonal, truncated triangular, and other symmetrical structures. The nanoplates are composed of essentially (111) lattice planes, as revealed by both XRD and TEM results. Nanoplates with widths from several hundreds of nanometers to a few microns absorb light strongly in the near-infrared region. The growth mechanism of these nanoplates was investigated. The ability to synthesize gold nanoplates with these different size ranges in large scale in aqueous solution using simple CTAB capping surfactant should allow more diverse applications of gold nanoplates.     

Structural and optical properties of KTa0.77Nb0.23O3 nanoplates synthesized by hydrothermal method

Two-dimensional KTa(0.77)Nb(0.23)O(3) (KTN) nanoplates with edge sizes of about 100 nm and thickness of about 10 nm have been fabricated by hydrothermal method at 200 degrees C using Ta(2)O(5), Nb(2)O(5), and KOH served as the precursors. Detailed structural studies indicate that the synthesized products are made up of large quantity single crystalline nanoplates with quadrilateral shape, which have a cubic perovskite structure without any other impurity phase and (011) growth direction. The stacking faults may be the key in the formation and growth of the (011) plate. Room temperature photoluminescence spectra excited at different wavelengths exhibit a strong emission band centered at 470 nm (2.63 eV) as well as two weak emission peaking at 423 nm (3.06 eV) and 505 nm (2.46 eV), respectively. The electron-hole recombination of localized excitons should responsible for the light emissions at 423 and 470 nm. Room temperature Raman spectrum of KTN nanoplates reveal that the frequencies of vibration mode are lower slightly than that of KTN bulk materials, and the scattering profile is to be more diffused and enlarged, which may be induced by the crystal structure defects, such as stacking faults.     

CTAB assisted hydrothermal synthesis, controlled conversion and CO oxidation properties of CeO2 nanoplates, nanotubes, and nanorods

In this work, CeO₂ nanoplates were synthesized by a hydrothermal reaction assisted by hexadecyltrimethylammonium bromide (CTAB) at 100-160 °C. The size of nanoplates was around 40 nm. Further experiment showed that the controlled conversion of nanoplates into nanotubes, and nanorods can be realized by changing the reaction time, temperature, and CTAB/Ce³⁺ ratio value. X-ray diffraction (XRD), transmission electron microscopy (TEM), and Brunauer-Emmett-Teller (BET) nitrogen adsorption-desorption measurements were employed to characterize the samples. The CO oxidation properties of nanorods, nanoplates, and nanotubes were investigated. An enhanced catalytic activity has been found for CO oxidation by using CeO₂ nanoplates as compared with CeO₂ nanotubes and nanorods, and the crystal surfaces (100) of CeO₂ nanoplates were considered to play an important role in determining their catalytic oxidation properties.     

Optimization of high-yield biological synthesis of single-crystalline gold nanoplates

In this work, single-crystalline gold nanoplates were obtained by reducing aqueous chloroauric acid solution with the extract of Sargassum sp. (brown seaweed) at room temperature. The gold nanoplates so obtained were characterized by UV-vis spectroscopy, X-ray diffraction, atomic force microscopy, and transmission electron microscopy. The formation of gold nanoplates was found to depend on a number of environmental factors, such as the time taken to age the seaweed extract, pH of the reaction medium, reaction temperature, reaction time, and initial reactant concentrations. The size of the gold nanoplates could be controlled to between 200 and 800 nm by manipulating the initial reactant concentrations. The yield of the flat gold nanocrystals relative to the total number of nanoparticles formed was as high as approximately 80-90%.     

边长为微米级的银纳米片的简易合成与形成机理

用低温(60 ℃)溶剂热法, 以N,N-二甲基甲酰胺(DMF)为主还原剂和溶剂, 以聚乙烯吡咯烷酮(PVP)为辅助还原剂和晶面生长控制剂, 以硝酸银为前驱物, 大量制备了高纯度的、边长为微米级、宽厚比≥10的单晶银纳米片. 采用粉末X射线衍射(PXRD)、场发射扫描电镜(FE-SEM)、透射电子显微镜(TEM)等表征和分析了合成产物的成分、形貌和结构. 结果表明, 合成的银纳米片为面心立方单晶, 边长为1-4 μm, 厚度为50-100 nm. 考察了不同溶剂对银纳米结构的影响, 并提出了大尺寸的银纳米片的形成机理. 本文为调控单晶银纳米片的边长和宽厚比提供了一种新的可靠的动力学方法, 制备的长边长、大宽厚比的单晶银纳米片在聚合物基导电复合材料和电磁屏蔽材料方面有潜在的重要应用.     

Spectrofluorometric determination of ketorolac tromethamine via its oxidation with cerium(IV) in pharmaceutical preparations and biological fluids

A simple and sensitive fluorometric method for determination of ketorolac tromethamine was studied. The method depends on oxidation of the drug with cerium(IV) and subsequent monitoring of the fluorescence of the induced cerium(III) at lambda(em) 365 nm after excitation at 255 nm. Different variables affecting the reaction conditions, such as the concentrations of cerium(IV), sulfuric acid concentration, reaction time, and temperature, were carefully studied and optimized. Under the optimum conditions, a linear relationship was found between the relative fluorescence intensity and the concentration of the investigated drug in the range of 0.1-0.8 microg/mL. No interferences could be observed from the excipients commonly present in dosage forms. The proposed method was successfully applied to the analysis of the investigated drug in its pure form, pharmaceutical preparations, and biological fluids with good accuracy and precision. The recoveries for pharmaceutical formulations ranged from 99.8-101.0 +/- 0.6% for tablets, 98.5-101.0 +/- 1.0% for ampoules, and 99.0-100.5 +/- 0.7% for eye drops. The results obtained by the proposed method were satisfactory compared with those obtained by the official method. The recoveries for biological fluids were 99.1-100.4 +/- 0.7 and 99.0-100.0 +/- 0.5% for plasma and urine, respectively.