Formation of solid solutions of multiferroics in the Bi<Subscript>2</Subscript>O<Subscript>3</Subscript>–Nd<Subscript>2</Subscript>O<Subscript>3</Subscript>–Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> system

The sequence of phases appearance during the formation of Bi_1–xNd_xFeO₃ solid solutions in powder oxides mixtures of bismuth, neodymium, and iron has been determined. It has been shown that the closeness of the reaction mixture composition to that of the individual compound (BiFeO₃ or NdFeO₃) is essential for the realization of the series of phase transformations yielding solid solutions of multiferroics Bi_1–xNd_xFeO₃ as the final product, due to the prevalence of various interphase contacts in the starting reaction zone.     

Reduction of Oxide Mixtures of (Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> + CuO) and (Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> + Co<Subscript>3</Subscript>O<Subscript>4</Subscript>) by Low-Temperature Hydrogen Plasma

The paper presents experimental results pertaining to the reduction of oxide mixtures namely (Fe₂O₃ + CuO) and (Fe₂O₃ + Co₃O₄), by low-temperature hydrogen plasma in a microwave hydrogen plasma set-up, at microwave power 750 W and hydrogen flow rate 2.5 × 10^?6 m³ s^?1. The objective was to examine the effect of addition of CuO or Co₃O₄, on the reduction of Fe₂O₃. In the case of the Fe₂O₃ and CuO mixture, oxides were reduced to form Fe and Cu metals. Enhancement of reduction of iron oxide was marginal. However, in the case of the Fe₂O₃ and Co₃O₄ mixture, FeCo alloy was formed within compositions of Fe₇₀Co₃₀, to Fe₃₀Co₇₀. Since the temperature was below 841 K, no FeO formed during reduction and the sequence of Fe₂O₃ reduction was found to be Fe₂O₃ → Fe₃O₄ → Fe. Reduction of Co₃O₄ preceded that of Fe₂O₃. In the beginning, the reduction of oxides led to the formation of Fe–Co alloy that was rich in Co. Later Fe continued to enter into the alloy phase through diffusion and homogenization. The lattice strain of the alloy as a function of its composition was measured. In the oxide mixture in which excessive amount of Co₃O₄ was present, all the Co formed after reduction could not form the alloy and part of it appeared as FCC Co metal. The crystallite size of the alloy was in the range of 22–30 nm. The crystal size of the Fe–Co alloy reduced with an increase in Co concentration.     

Synthesis of Fe<Subscript>3</Subscript>O<Subscript>4</Subscript>@Au core–shell nanoparticles

A new two-step synthesis of Fe₃O₄@Au core–shell nanoparticles stabilized in polyethylene glycol is described. The nanoparticles were characterized by transmission electron microscopy, X-ray powder diffraction, UV and Mössbauer spectroscopy. Fe₃O₄@Au nanoparticles featured both optical properties (they featured a plasmon resonance band) and magnetic properties (they responded to an external magnetic field), typical of individual gold and magnetite nanoparticles, respectively.     

Synthesis and properties of magnetic superhydrophobic mesoporous Fe<Subscript>2</Subscript>O<Subscript>3</Subscript>–SiO<Subscript>2</Subscript> composites

Ways to obtain Fe₂O₃–SiO₂ iron-containing silica composites with organized mesoporous structure (MCM-41) and large specific surface area (up to 1476 m² g^–1) were considered. The influence exerted by the method used to synthesize the materials on their structure, texture characteristics, particle size, and magnetic properties were studied. The aggregative stability of samples was examined. It was shown that treatment of the resulting composites with compounds from the chlorosilane group affects their hydrophobic properties.     

Thermal studies of ZnO–B<Subscript>2</Subscript>O<Subscript>3</Subscript>–P<Subscript>2</Subscript>O<Subscript>5</Subscript>–TeO<Subscript>2</Subscript> glasses

The effect of TeO₂ additions on the thermal behaviour of zinc borophosphate glasses were studied in the compositional series (100 − x)[0.5ZnO–0.1B₂O₃–0.4P₂O₅]–xTeO₂ by differential scanning calorimetry, thermodilatometry and heating microscopy thermal analysis. The addition of TeO₂ to the starting borophosphate glass resulted in a linear increase of glass transition temperature and dilatometric softening temperature, whereas the thermal expansion coefficient decreased. Most of glasses crystallize under heating within the temperature range of 440–640 °C. The crystallization temperature steeply decreases with increasing TeO₂ content. The lowest tendency towards crystallization was observed for the glasses containing 50 and 60 mol% TeO₂. X-ray diffraction analysis showed that major compounds formed by annealing of the glasses were Zn₂P₂O₇, BPO₄ and α-TeO₂. Annealing of the powdered 50ZnO–10B₂O₃–40P₂O₅ glass leads at first to the formation of an unknown crystalline phase, which is gradually transformed to Zn₂P₂O₇ and BPO₄ during subsequent heating.     

Concentration Space of Homogeneous Garnet in the System Ga<Subscript>2</Subscript>O<Subscript>3</Subscript>–(Y,Bi)<Subscript>3</Subscript>(Fe,Ga)<Subscript>5</Subscript>O<Subscript>12</Subscript>–Fe<Subscript>2</Subscript>O<Subscript>3</Subscript>

The concentration space of homogeneous garnet in the system Ga₂O₃–(Y, Bi)₃(Fe, Ga)₅O₁₂–Fe₂O₃ was determined by X-ray powder diffraction analysis. The obtained results expand the knowledge of the possible variations of cation ratios Y : Bi : Fe : Ga in garnet, which can be used for searching for and creating new stable magneto-optical materials.     

Photoelectrochemical performance of bilayered Fe–TiO<Subscript>2</Subscript>/Zn–Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> thin films for solar generation of hydrogen

A visible-light sensitive bilayered photoanode of Fe–TiO₂/Zn–Fe₂O₃ has been developed by spray pyrolytically depositing Zn–Fe₂O₃ layers onto predeposited Fe–TiO₂ thin film on ITO substrate. Fe–TiO₂/Zn–Fe₂O₃ photoelectrodes were characterized by XRD, Raman, AFM, UV-vis absorption spectroscopy. Photoelectrochemical properties of bilayered Fe–TiO₂/Zn–Fe₂O₃ photoelectrode were studied by Mott–Schottky curves and I–V characteristics. Bilayered Fe–TiO₂/Zn–Fe₂O₃ photoelectrode was observed to possess much higher separation efficiency of photogenerated charge carriers and could generate nine times better photocurrent density than pure Fe–TiO₂. Solar to hydrogen conversion efficiency exhibited by this electrode was 0.77%.     

Distribution of niobium and lanthanum between two immiscible melts in the system LaPO<Subscript>4</Subscript>–SiO<Subscript>2</Subscript>–NaF–Nb<Subscript>2</Subscript>O<Subscript>5</Subscript>–Fe<Subscript>2</Subscript>O<Subscript>3</Subscript>

The system LaPO₄–SiO₂–NaF–Nb₂O₅–Fe₂O₃ is characterized by immiscibility fields in the liquid state region. Addition of iron expands fields of immiscibility of melts and decreases the temperature of their coexistence. A fraction of 87–90% of niobium is extracted into iron silicate melt, and 92–98% of lanthanum is extracted into phosphate salt melt.     

Modifying additives affect the properties of Y<Subscript>2</Subscript>O<Subscript>3</Subscript>–Al<Subscript>2</Subscript>O<Subscript>3</Subscript>–SiO<Subscript>2</Subscript> system

The effects caused by modifying additives, namely nonionic surfactants (Tween 80 and Neonol AF 9-6) and oxides (B₂O₃ and HfO₂), on the rheology, film formation, and phase formation in the yttrium aluminum silicate system prepared by sol–gel technology were studied. The effect of 1 wt % HfO₂ additions on the activation energy of crystallization was studied.     

Structural and Temperature Dependent Electrical Conductivity Properties of Dy<Subscript>2</Subscript>O<Subscript>3</Subscript>–Sm<Subscript>2</Subscript>O<Subscript>3</Subscript> CO-Doped Bi<Subscript>2</Subscript>O<Subscript>3</Subscript>

In the present work, Dy₂O₃ and Sm₂O₃ double-doped Bi₂O₃-based materials are synthesized by exploiting the solid-state synthesis method. The structural and temperature dependent electrical properties of these ternary ceramic samples, which are candidate materials for solid oxide fuel cell (SOFCs) electrolyte, are determined by means of a powder X-ray diffractometer (XRD), the four point-probe method (FPPM), and the thermal-gravimetry/differential thermal analysis (TG/DTA). As a result of the XRD measurements, the fluorite-type fcc δ-phase with a stable structure is obtained for higher values of the dopant oxide material, which are the samples with the maximum content of fixed 20% Dy₂O₃ and 15% and 20% Sm₂O₃. The samples with the stable δ-phase structure have higher conductivities. The highest electrical conductivity is found for the (Bi₂O₃)0.6(Dy₂O₃)_0.2(Sm₂O₃)_0.2 sample, which was 2.5×10^–2 (Ohm cm)^–1 at 750 °C. The activation energies are also calculated from the Arrhenius charts, which were determined from the FPPM measurements. The lowest activation energy is found as 0.85 eV for the sample with the highest electrical conductivity.     

Thermal analysis study of LiFeO<Subscript>2</Subscript> formation from Li<Subscript>2</Subscript>CO<Subscript>3</Subscript>–Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> mechanically activated reagents

Series of n-octadecane/expanded graphite composite phase-change materials (PCMs) with different mass ratio were prepared using n-octadecane as PCMs, expanded graphite as multi-porous supporting matrix through vacuum impregnation method. Microstructure, crystallization properties, energy storage behavior, thermal cycling property and intelligent temperature-control performance of the composite PCMs were investigated. Results show that the composite PCMs have a good energy storage property. The melting enthalpy and crystallization enthalpy can reach 164.85 and 176.51 J g^?1, respectively. Furthermore, the good thermal conductivity of expanded graphite reduces the super-cooling degree of n-octadecane and endows the composite PCMs with fast thermal response rate and excellent thermal cycling stability. As a result, the phase-change temperatures and phase-change enthalpy almost have no change after 50 thermal-cooling cycles. The test of intelligent temperature-control performance shows that the electronic radiator filled with the composite PCMs possesses a high intelligent temperature-control performance, and its temperature can sustain in the range of 22–27.5 °C for about 6120 s. These results indicate that the prepared composite PCMs possess good comprehensive property and can be widely used in energy storage and thermal management systems.     

Thermal properties of Ga<Subscript>2</Subscript>O<Subscript>3</Subscript>–PbO–P<Subscript>2</Subscript>O<Subscript>5</Subscript> glass system

Thermal behavior of xGa₂O₃–(50 − x)PbO–50P₂O₅ (x = 0, 10, 20, and 30 mol.% Ga₂O₃) and xGa₂O₃–(70 − x)PbO–30P₂O₅ (x = 0, 10, 20, 30, and 40 mol.% Ga₂O₃) glassy materials were studied by thermo-mechanical analysis (TMA) and differential thermal analysis (DTA). Replacement of PbO for Ga₂O₃ is accompanied by increasing glass-transition temperature (263 ≤ T _g/°C ≤ 535), deformation temperature (363 ≤ T _d/°C ≤ 672), crystallization temperature (396 ≤ T _c/°C ≤ 640) and decreasing of coefficient of thermal expansion (5.1 ≤ CTE/ppm K⁻¹ ≤ 16.7). Values of Hruby parameter were determined (0.1 ≤ K _H ≤ 1.3). The thermal stability of prepared glasses increases with increasing of concentration of Ga₂O₃.     

Glass Formation in the Ternary System La<Subscript>2</Subscript>O<Subscript>3</Subscript>–As<Subscript>2</Subscript>S<Subscript>3</Subscript>–Er<Subscript>2</Subscript>O<Subscript>3</Subscript>

The boundaries of the glass formation region in the ternary system La₂O₃–As₂S₃–Er₂O₃ were found. Transparent glass of composition (La₂O₃)_0.03(As₂S₃)0.90(Er₂O₃)0.07 was studied by X-ray photoelectron and Raman spectroscopy. The intensities of the bands characterizing As–S, La–O, and Er–O bonds increased, and these bands were shifted toward higher energies. This was due to an increase in the covalence of these bonds and probably due to the formation of new bonds in the glasses. Samples in the glass formation region are resistant at 300 K to air, water, and organic solvents.     

Synthesis and properties of γ-Ga<Subscript>2</Subscript>O<Subscript>3</Subscript>–Al<Subscript>2</Subscript>O<Subscript>3</Subscript> solid solutions

The textural and structural properties of mixed oxides Ga₂O₃–Al₂O₃, obtained via impregnating γ-Al₂O₃ with a solution of Ga(NO₃)₃ and subsequent heat treatment, are studied. According to the results from X-ray powder diffraction, gallium ions are incorporated into the structure of aluminum oxide to form a solid solution of spinel-type γ-Ga₂O₃–Al₂O₃ up to a Ga₂O₃ content of 50 wt % of the total weight of the sample, accompanied by a reduction in the specific surface area, volume, and average pore diameter. It is concluded that when the Ga₂O₃ content exceeds 50 wt %, the β-Ga₂O₃ phase is observed along with γ-Ga₂O₃–Al₂O₃ solid solution. ⁷¹Ga and ²⁷Al NMR spectroscopy shows that gallium replaces aluminum atoms from the tetrahedral position to the octahedral coordination in the structure of γ-Ga₂O₃–Al₂O₃.     

Characterization of gold supported on Al<Subscript>2</Subscript>O<Subscript>3</Subscript>–CuO–Mn<Subscript>2</Subscript>O<Subscript>3</Subscript> catalysts obtained by thermal decomposition of aerosols

The purpose of this work was to employ the differential thermal analysis (DTA) technique to compare variations in the collapse energy of the zeolite Y crystalline structure in a fresh catalyst and in the same catalyst impregnated with nickel and vanadium. A small exothermic signal in the DTA curve at 950–1150 °C indicated the collapse of the crystalline structure. The areas of the exothermic signals in the DTA curves of the two samples indicated a reduction in the curve of the metal impregnated catalyst. These results were compared with X-ray data, leading to the conclusion that metal impregnation affects the zeolite Y crystalline structure and that the DTA technique is a potentially useful tool for measuring the integrity of zeolite Y in catalysts.     

Preparation and characterization of rapid magnetic recyclable Fe<Subscript>3</Subscript>O<Subscript>4</Subscript>@SiO<Subscript>2</Subscript>@TiO<Subscript>2</Subscript>–Sn photocatalyst

Effective procedure to synthesize Fe₃O₄@SiO₂@TiO₂–Sn magnetically separable photocatalyst by a combination of co-precipitation, sol–gel and photodeposition methods was introduced. Products were characterized by XRD, SEM, VSM, EDS, DRS, TEM, ICP-OES and IR techniques. The dimensions of catalyst particle size were evaluated by scanning electron microscopy, and results approved nanoscale size for product. In addition, studying the magnetic nature by VSM analysis showed superparamagnetic properties for all samples. XRD pattern indicates that TiO₂ coated on Fe₃O₄@SiO₂ core well crystallized at 400 °C in anatase phase. Synthesized photocatalyst shows good photocatalytic performance in decolorization of rhodamine B aqueous solution. The composite nanoparticles showed high recycling efficiency and stability over five separation cycles.     

Mass attenuation coefficients of B<Subscript>2</Subscript>O<Subscript>3</Subscript>–Al<Subscript>2</Subscript>O<Subscript>3</Subscript>–SiO<Subscript>2</Subscript>–CaF<Subscript>2</Subscript> glass system at 0.662 and 1.25 MeV gamma energies

The total mass attenuation coefficients, partial interaction and the effective atomic numbers (Z_eff) of glass system (80−x)B₂O₃–10Al₂O₃–10SiO₂–xCaF₂ (where x = 5, 10, 20, 25, 30, 35 and 40 mol %) have been calculated at photon energies 0.662 and 1.25 MeV using the WinXCom software on the basis of mixture rule. Results indicated that the total mass attenuation coefficients showed a decrease with increasing the CaF₂ concentration, due to a decrease in Compton scattering probability, which gave a dominant contribution to the total mass attenuation coefficients for the studied glass samples at both energies. However, the photoelectric absorption and coherent scattering showed an increase with increasing the CaF₂, concentrations at same energies. For a comparison, the total mass attenuation coefficients of the glass system had lower values at the energy 1.25 MeV than that at 0.662 MeV. Z_eff was found to increase linearly with the increase of CaF₂ concentrations. It was concluded that low CaF₂ concentrations in glass system, under study, have Z_eff close to that of human tissue and have higher total absorption coefficients at energy of 0.662 MeV than that at 1.25 MeV. These results are very useful in designing gamma radiation detectors using thermoluminescence technique. Therefore, it is recommended to use low CaF₂ concentration of our glass system as good gamma detectors at energy of 1.25 MeV.     

Atmospheric control of gel-oxide transformation in sol–gel derived Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-Y<Subscript>2</Subscript>O<Subscript>3</Subscript> fibers

Via sol–gel processing metal–organic fibers were produced and dried up to 140 °C. For these gel fibers the influence of a treatment in different atmospheres was investigated for the temperature range of 200–850 °C. The atmospheres were nitrogen, water vapor, evaporated nitric and hydrochloric acid and evaporated hydrogen peroxide. In the presence of moisture and especially with acidic moisture fibers were transformed almost completely to their oxide composition (82 mol% Al₂O₃·18 mol% Y₂O₃). In these inorganic amorphous structures considerable differences were observed on several structural levels. On the atomic scale, the coordination of Al ions was investigated by ²⁷Al MAS NMR and skeletal density by He-pycnometry. Porosity in the nm scale was characterized by N₂-sorption. As a macroscopic effect of different treatment atmospheres, the longitudinal shrinkage was observed. For fibers treated at 500 °C the relative shrinkage varied by 100% (comparing water vapor and nitrogen atmosphere). No simple correlation between the release of organic constituents, the formation of porosity and the shrinkage could be found. These aspects were controlled by the rigidity of the inorganic network against atomic reconstitution. The kind of atmosphere was found to be an effective parameter to control various aspects of the xerogel structure.     

Effect of MoO<Subscript>3</Subscript> additions on the thermal stability and crystallization kinetics of PbO–Sb<Subscript>2</Subscript>O<Subscript>3</Subscript>–As<Subscript>2</Subscript>O<Subscript>3</Subscript> glasses

The present paper reports on the effect of MoO₃ on the glass transition, thermal stability and crystallization kinetics for (40PbO–20Sb₂O₃–40As₂O₃)_100−x –(MoO₃) _x (x = 0, 0.25, 0.5, 0.75 and 1 mol%) glasses. Differential scanning calorimetry (DSC) results under non-isothermal conditions for the studied glasses were reported and discussed. The values of the glass transition temperature (T _g) and the peak temperature of crystallization (T _p) are found to be dependent on heating rate and MoO₃ content. From the compositional dependence and the heating rate dependence of T _g and T _p, the values of the activation energy for glass transition (E _g) and the activation energy for crystallization (E _c) were evaluated and discussed. Thermal stability for (40PbO–20Sb₂O₃–40As₂O₃)_100−x –(MoO₃) _x glasses has been evaluated using various thermal stability criteria such as ΔT, H _r , H _g and S. Moreover, in the present work, the K _r(T) criterion has been considered for the evaluation of glass stability from DSC data. The stability criteria increases with increasing MoO₃ content up to x = 0.5 mol%, and decreases beyond this limit.