Solution‐processed high‐performance orange phosphorescent and white PLEDs with a high color‐rendering index from an unprecedented π‐stacked and π‐conjugated host material

A blue fluorescent polymer based on poly(vinyl carbazole) (PVK) and terfluorene, combined to make a chemical hybrid at the carbazole unit (PVK‐TF), is fully characterized in this study. PVK‐TF shows useful emission features, such as peaks at 400, 420, 437, 460, and 496 nm, depending on the processing conditions. It possesses a relatively high triplet energy level (2.23 eV), electrochemical stability, good film‐forming ability, and morphological stability. Based on this blue fluorescent material, highly efficient orange phosphorescent polymer light‐emitting diodes (PLEDs) were fabricated with a maximum efficiency of 21.99 cd A^?1, and a maximum luminance of 19552.3 cd m^?2. Single‐layer hybrid white PLEDs were developed, with a high color rendering index of 81.9 that emitted across the whole visible spectrum from 380 to 780 nm, corresponding to the Commission International de L'Eclairage coordinates x, y values of around (0.38, 0.40) and CCT = 3774, with a maximum current efficiency of 10.69 cd A^?1, and a maximum brightness of 15723.3 cd m^?2. © 2014 Wiley Periodicals, Inc. J. Polym. Sci. Part B: Polym. Phys. 2014 , 52, 587–595     

Synthesis and characterization of light‐emitting oligo(p‐phenylene‐vinylene)s and polymeric derivatives containing three‐ and five‐conjugated phenylene rings. II. Electro‐optical properties and optimization of PLED performance

A series of multilayer polymeric light‐emitting diodes (PLEDs) containing an electron‐transporting layer (ETL), that is tris(8‐quinolinolato)‐aluminum(III) (Alq) and 2,2′,2″‐(1,3,5‐phenylene)‐tris[1‐phenyl‐1H‐benzimidazole] (TPBI), were fabricated by doping fluorescent oligo(p‐phenylene‐vinylene)s (BIII and BV) and polymer derivatives (PBV) into poly(N‐vinyl carbazole) (PVK). These PLEDs can be optimized by the design of multilayer device configurations (brightness increased 8–15 times by addition of ETL) and possess greenish electroluminescent (EL) spectra peaked about 500–540 nm. A remarkably high brightness of 56,935 cd/m² with a power efficiency of 3.25 lm/W was obtained in the device of PVK:BVOC₈‐OC₈ (100:20)/Alq (60 nm/60 nm). It suggests that the emission mechanism (including the conjugated and excimer emissions of BVOC₈‐OC₈ emitters) originates from both of BVOC₈‐OC₈ and ETL (Alq and TPBI) by varying the concentration of chromophores and adjusting the thickness of ETL. The concentration effect of the emitters in PVK (i.e. PVK:BVOC₈‐OC₈ = 100:5, 100:20, and 100:100 wt %) and the influence of the ETL (including its thickness) on the EL characteristics are also reported. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2922–2936, 2006     

Performance Improvement of Organic Light Emitting Diodes Using Poly(N-vinylcarbazole) (PVK) as a Blocking Layer

High efficiency organic light‐emitting‐devices (OLED) have been fabricated by incorporation of a polymeric layer as a controller of the unbalanced charge. In device configuration of ITO/PEDOT:PSS/PVK/Alq₃/LiF:Al, poly(N‐vinylcarbazole) (PVK) was selected as a block‐ing layer (BL) because it has a hole transporting property and a higher band gap, especially a lower LUMO level than the emitting layer (Alq₃) and a higher HOMO level than the hole injection layer (PEDOT: PSS). As a result, the optimal structure with this bl layer showed a peak efficiency of 6.89 cd/A and 2.30 lm/W compared to the device without the PVK layer of 1.08 cd/A, 0.27 lm/W. This result shows that the PVK layer could effec‐tively block the electrons from metal cathode and confine them in the emitting layer and accomplish the charge balance, which leads to enhanced hole‐electron balance for achieving high recombination efficiency.     

A novel oligothiophene derivative as a hole‐transport with emitting material for OLED

A novel oligothiophene derivative containing the triphenylamine moiety with high glass transition temperature (T_g; 135 °C), 5,5′‐{bis[4‐di(4‐thiophenyl)amino]phenyl}‐2,2′‐bithiophene (TTPA‐dimer) was synthesized by the dimerization of tris[4‐(2‐thienyl)phenyl]amine (TTPA) with a palladium catalysis. Some types of electroluminescent (EL) devices that use the amorphous material for a hole‐ and an electron‐transporting with an emitting layer were fabricated. These devices emitted a bright green‐yellowish light (λ_emi; around 510 nm) with a small full width at half maximum (FWHM) rather than that of Alq₃. The single layer EL device showed a maximum luminance of 221 cd/m² at 8 V (0.06 lm/W at 100 cd/m²). On the other hand, the double layer (TTPA‐dimer/Alq₃) EL device that used Alq₃ as the electron transport material was increased up to 10830 cd/m² at 12 V (0.89 lm/W at 300 cd/m²) and with a lower turn‐on voltage (3.2 V at 0.1 cd/m²) than other types of EL devices. Copyright © 2003 John Wiley & Sons, Ltd.     

Synthesis and electrochemical and electroluminescent properties of N‐phenylcarbazole‐substituted poly(p‐phenylenevinylene)

An N‐phenylcarbazole‐containing poly(p‐phenylenevinylene) (PPV), poly[(2‐(4′‐carbazol‐9‐yl‐phenyl)‐5‐octyloxy‐1,4‐phenylenevinylene)‐alt‐(2‐(2′‐ethylhexyloxy)‐5‐methoxy‐1,4‐phenylenevinylene)] (Cz‐PPV), was synthesized, and its optical, electrochemical, and electroluminescent properties were studied. The molecular structures of the key intermediates, the carbazole‐containing boronic ester and the dialdehyde monomer, were crystallographically characterized. The polymer was soluble in common organic solvents and exhibited good thermal stability with a 5% weight loss at temperatures above 420 °C in nitrogen. A cyclic voltammogram showed the oxidation peak potentials of both the pendant carbazole group and the PPV main chain, indicating that the hole‐injection ability of the polymer would be improved by the introduction of the carbazole‐functional group. A single‐layer light‐emitting diode (LED) with a simple configuration of indium tin oxide (ITO)/Cz‐PPV (80 nm)/Ca/Al exhibited a bright yellow emission with a brightness of 1560 cd/m² at a bias of 11 V and a current density of 565 mA/cm². A double‐layer LED device with the configuration of ITO/poly(3,4‐ethylenedioxy‐2,5‐thiophene):poly (styrenesulfonic acid) (60 nm)/Cz‐PPV (80 nm)/Ca/Al gave a low turn‐on voltage at 3 V and a maximum brightness of 6600 cd/m² at a bias of 8 V. The maximum electroluminescent efficiency corresponding to the double‐layer device was 1.15 cd/A, 0.42 lm/W, and 0.5%. The desired electroluminescence results demonstrated that the incorporation of hole‐transporting functional groups into the PPVs was effective for enhancing the electroluminescent performance. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 5765–5773, 2005     

Anthracene‐Cored Dendrimer for Solution‐Processible Blue Emitter: Syntheses,Characterizations, Photoluminescence,and Electroluminescence

Summary: A second‐generation blue fluorescent anthracene‐cored dendrimer EH‐G2AN was readily synthesized via a convergent method. Its monodispersity was confirmed by ¹H NMR and MALDI‐TOF mass measurement. The peak emission of EH‐G2AN in a dilute CH₂Cl₂ solution was observed at 416 nm with a shoulder at 434 nm and moved to 418 nm in the solid film with the shoulder at 433 nm. The nearly “perfect” overlap of solution and solid emission spectra revealed the absence of molecular aggregations in the solid film, which was apparently suppressed by the presence of rigid and bulky 1,3,5‐phenylene‐based dendrons and 2‐ethylhexyloxy solubilizing peripheral groups. EH‐G2AN appeared strikingly stable with the onset decomposition temperature above 350 °C and remained at the high temperature of 428 °C where 5% weight loss occurred. The electroluminescent device [ITO/PEDOT:PSS/EH‐G2AN/Ba/Al] showed a peak emission at 442 nm and maximal external device efficiency of 0.82%@170 cd · m⁻². After inserting a PVK layer between the hole injection layer and emitting layer, a maximal external device efficiency of 1.05%@184 cd · m⁻² was obtained with a narrow FWHI of merely ca. 42 nm in the device configuration [ITO/PEDOT:PSS/PVK/EH‐G2AN/Ba/Al].

     

带烷氧基的苯基蒎烯吡啶铱配合物在聚合物电致发光器件中的应用研究

采用旋涂法将一组带烷氧基的苯基蒎烯吡啶铱(Ⅲ)配合物(Ir(RO-pppy)₃)磷光材料掺杂到PVK中,制作出了聚合物电致发光器件:ITO/PE-DOT:PSS(40 nm)/PVK_0.7:PBD_0.3:(x%.)Ir-complex(80 nm)/CsF(1.5 nm)/Mg:Ag(200 nm).实验结果表明,带有长烷氧基链配体的铱(Ⅲ)配合物能表现出更好的器件行为,当掺杂浓度为3.2%时,器件的最高发光效率达19.9 cd/A(7.8 lm/W,9.1V),CIE为(0.20,0.56);器件最大亮度为15700 cd/m²(8.4V).通过对这组铱(Ⅲ)配合物的光物理行为及电化学性能的研究,考察了主体材料与配合物之间的能级配置以及能量转移的机理.     

Enantioselective micellar electrokinetic chromatography of dl‐amino acids using (+)‐1‐(9‐fluorenyl)‐ethyl chloroformate derivatization and UV‐induced fluorescence detection

Chiral analysis of dl ‐amino acids was achieved by micellar electrokinetic chromatography coupled with UV‐excited fluorescence detection. The fluorescent reagent (+)‐1‐(9‐fluorenyl)ethyl chloroformate was employed as chiral amino acid derivatizing agent and sodium dodecyl sulfate served as pseudo‐stationary phase for separating the formed amino acid diastereomers. Sensitive analysis of (+)‐1‐(9‐fluorenyl)ethyl chloroformate‐amino acids was achieved applying a xenon‐mercury lamp for ultraviolet excitation, and a spectrograph and charge‐coupled device for wavelength‐resolved emission detection. Applying signal integration over a 30 nm emission wavelength interval, signal‐to‐noise ratios for derivatized amino acids were up to 23 times higher as obtained using a standard photomultiplier for detection. The background electrolyte composition (electrolyte, pH, sodium dodecyl sulfate concentration, and organic solvent) was studied in order to attain optimal chemo‐ and enantioseparation. Enantioseparation of 12 proteinogenic dl ‐amino acids was achieved with chiral resolutions between 1.2 and 7.9, and detection limits for most derivatized amino acids in the 13–60 nM range (injected concentration). Linearity (coefficients of determination > 0.985) and peak‐area and migration‐time repeatabilities (relative standard deviations lower than 2.6 and 1.9%, respectively) were satisfactory. The employed fluorescence detection system provided up to 100‐times better signal‐to‐noise ratios for (+)‐1‐(9‐fluorenyl)ethyl chloroformate‐amino acids than ultraviolet absorbance detection, showing good potential for d ‐amino acid analysis.     

High-performance blue electroluminescent devices based on 2-(4-biphenylyl)-5-(4-carbazole-9-yl)phenyl-1,3,4-oxadiazole

An electron transporting moiety (1,3,4-oxadiazole) and a hole transporting moiety (carbazole) were combined to create 2-(4-biphenylyl)-5-(4-carbazole-9-yl)phenyl-1,3,4-oxadiazole (CzOxa), a three layer device with a configuration of ITO/TPD(50 nm)/CzOxa(40 nm)/AlQ(40 nm)/Mg0.9Ag0.1(200 nm)/Ag(80 nm) which exhibited a blue emission peak at approximately 470 nm (x = 0.14, y = 0.19) with a maximum luminance of 26,200 cd m(-2) at a drive voltage of 15 V and a maximum luminous efficiency of 2.25 lm W(-1).     

Synthesis and Crystal Structure of [1‐(η5‐9‐Fluorenyl)‐2‐(η5‐1‐indenyl)ethane]hafnium Dimethyl

The synthesis and characterization of the unsymmetric hafnium dialkyl [1‐(η⁵‐9‐fluorenyl)‐2‐(η⁵‐1‐indenyl)ethane]HfCl₂ ( 2 ) and corresponding dimethyl complex [1‐(η⁵‐9‐fluorenyl)‐2‐(η⁵‐1‐indenyl)ethane]Hf(CH₃)₂ ( 3 ) is described. The dialkyl hafnocene ( 3 ) crystallizes in monoclinic space group P2₁/c (No. 14) with a = 9.458(8), b = 8.541(8), c = 23.733(11) Å, β = 93.16(5) deg., V = 1914(3) ų, Z = 4. Further on, complex 3 was activated with methylaluminiumoxane (MAO) and utilized as a catalyst in ethene polymerization.     

Fluorene‐based alternating polymers containing electron‐withdrawing bithiazole units: Preparation and device applications

We report here the synthesis via Suzuki polymerization of two novel alternating polymers containing 9,9‐dioctylfluorene and electron‐withdrawing 4,4′‐dihexyl‐2,2′‐bithiazole moieties, poly[(4,4′‐dihexyl‐2,2′‐bithiazole‐5,5′‐diyl)‐alt‐(9,9‐dioctylfluorene‐2,7‐diyl)] (PHBTzF) and poly[(5,5′‐bis(2″‐thienyl)‐4,4′‐dihexyl‐2,2′‐bithiazole‐5″,5″‐diyl)‐alt‐(9,9‐dioctylfluorene‐2,7‐diyl)] (PTHBTzTF), and their application to electronic devices. The ultraviolet–visible absorption maxima of films of PHBTzF and PTHBTzTF were 413 and 471 nm, respectively, and the photoluminescence maxima were 513 and 590 nm, respectively. Cyclic voltammetry experiment showed an improvement in the n‐doping stability of the polymers and a reduction of their lowest unoccupied molecular orbital energy levels as a result of bithiazole in the polymers' main chain. The highest occupied molecular orbital energy levels of the polymers were ?5.85 eV for PHBTzF and ?5.53 eV for PTHBTzTF. Conventional polymeric light‐emitting‐diode devices were fabricated in the ITO/PEDOT:PSS/polymer/Ca/Al configuration [where ITO is indium tin oxide and PEDOT:PSS is poly(3,4‐ethylenedioxythiophene) doped with poly(styrenesulfonic acid)] with the two polymers as emitting layers. The PHBTzF device exhibited a maximum luminance of 210 cd/m² and a turn‐on voltage of 9.4 V, whereas the PTHBTzTF device exhibited a maximum luminance of 1840 cd/m² and a turn‐on voltage of 5.4 V. In addition, a preliminary organic solar‐cell device with the ITO/PEDOT:PSS/(PTHBTzTF + C₆₀)/Ca/Al configuration (where C₆₀ is fullerene) was also fabricated. Under 100 mW/cm² of air mass 1.5 white‐light illumination, the device produced an open‐circuit voltage of 0.76 V and a short‐circuit current of 1.70 mA/cm². The fill factor of the device was 0.40, and the power conversion efficiency was 0.52%. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 1845–1857, 2005     

White electroluminescence from a single polyfluorene containing bis‐DCM units

A series of fluorene‐based copolymers composed of blue‐ and orange‐light‐emitting comonomers were synthesized through palladium‐catalyzed Suzuki coupling reactions. 9,9‐Dihexylfluorene and 2‐(2,6‐bis‐{2‐[1‐(9,9‐dihexyl‐9H‐fluoren‐2‐yl)‐1,2,3,4‐tetrahydroquinolin‐6‐yl]‐vinyl}‐pyran‐4‐ylidene)‐malononitrile (DCMF) were used as the blue‐ and orange‐light‐emitting chromophores, respectively. The resulting single polymers exhibited simultaneous blue (423/450 nm) and orange (580–600 nm) emissions from these two chromophores. By adjusting the fluorene and DCMF contents, white light emission could be obtained from a single polymer; a device with an ITO/PEDOT:PSS/polymer/Ca/Al configuration was found to exhibit pure white electroluminescence with Commission Internationale de L'Eclairage (CIE) coordinates of (0.33, 0.31), a maximum brightness of 1180 cd/m², and a current efficiency of 0.60 cd/A. Furthermore, the white light emission of this device was found to be very stable with respect to variation of the driving voltage. The CIE coordinates of the device were (0.32, 0.29), (0.32, 0.29), and (0.33, 0.31) for driving voltages of 7, 8, and 10 V, respectively. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 3380–3390, 2007     

Synthesis and characterization of 9,10‐diphenylanthracene‐based blue light emitting materials

A new series of conjugated polymers having diphenylanthracene vinylene biphenylene and diphenylanthracene vinylene terphenylene in the main chain and fluorene pendant group, were synthesized by nickel catalized Yamamoto coupling and palladium catalized Suzuki coupling. The obtained polymers showed good solubility in the common organic solvent and number average molecular weights of 14,000–9500 with a polydispersity indexes ranging from 1.7 to 2.1. Both polymers possess excellent thermal stability with glass transition temperatures of 123–127 °C and the onset decomposition temperatures of 420–400 °C. The obtained polymers showed blue emission (λ_max = 461 for PFPA and λ_max = 455 nm for PFPAME) in PL spectra, specially, PFPAME containing diphenylanthracene vinylene terphenylenevinylene showed the consistent emission in the solution and film. The double‐layered device with an ITO/PEDOT/PFPAME/LiF/Al structure has a turn‐on voltage of about 5.8 V, maximum brightness of 152 cd/m² and an electroluminescent efficiency of 0.143 lm/W, and stable blue EL emission that is not altered by increased voltage. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 5908–5916, 2009     

Intramolecular energy transferable (2,2‐diphenylvinyl)phenyl substituted poly(p‐phenylenevinylene) derivative with efficient photoluminescence and electroluminescence

A poly(p‐phenylenevinylene) (PPV) derivative containing a bulky (2,2‐diphenylvinyl)phenyl group in the side chain, EHDVP‐PPV, was synthesized by Gilch route. The reduced tolane‐bisbenzyl (TBB) defects, as well as the structure of the polymer, was confirmed by various spectroscopic methods. The intramolecular energy transfer from the (2,2‐diphenylvinyl)phenyl side group to the PPV backbone was studied by UV‐vis and photoluminescence (PL) of the obtained polymer and model compound. The polymer film showed maximum absorption and emission peaks at 454 and 546 nm, respectively, and high PL efficiency of 57%. A yellow electroluminescence (λ_max = 548 nm) was obtained with intensities of 6479 cd/m² when the light‐emitting diodes of ITO/PEDOT/EHDVP‐PPV/LiF/Al were fabricated. The maximum power efficiency of the devices was 0.729 lm/W with a turn‐on voltage of 3.6 V. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5636–5646, 2004     

Efficient electroluminescence from new lanthanide (Eu3+, Sm3+) complexes

The syntheses, structures, and electroluminescent properties are described for two new lanthanide complexes Ln(HFNH)3phen [HFNH = 4,4,5,5,6,6,6-heptafluoro-1-(2-naphthyl)hexane-1,3-dione; phen = 1,10-phenanthroline; Ln = Eu3+ (1), Sm3+ (2)]. Both complexes exhibit bright photoluminescence at room temperature (RT) due to the characteristic emission of Eu3+ and Sm3+ ion. Several devices using the two complexes as emitters were fabricated. The performances of these devices are among the best reported for devices using europium complex and samarium complex as emitters. The device based on 1 with the structure ITO/TPD (50 nm)/1:CBP (10%, 40 nm)/BCP (20 nm)/AlQ (30 nm)/LiF (1 nm)/Al (200 nm) exhibits the maximum brightness of 957 cd/m2, current efficiency of 4.14 cd/A, and power efficiency of 2.28 lm/W with a pure red Eu3+ ion emission. Especially, at the high brightness of 200 cd/m2, the device of 1 still has a high current efficiency of 2.15 cd/A. The device of 2 with a three-layer structure of ITO/TPD (50 nm)/2 (50 nm)/BCP (20 nm)/LiF (1 nm)/Al (200 nm) gives the maximum brightness of 42 cd/m2, current efficiency of 0.18 cd/A. By the comparison of the electroluminescent properties of devices based on Eu(TTA3phen (TTA = 2-thenoyltrifluoroacteonate) and 1, we conclude that the polyfluoration on the alkyl group of the ligand and the introduction of the long conjugate naphthyl group into the ligand improve the efficiency of 1-doped devices, especially at high current densities.     

Synthesis,photophysics, and electroluminescent performance of stable blue‐light‐emitting copoly(9,9‐diarylfluorene)s

A series of fluorene derivatives containing nonsymmetric and bulky aromatic groups at C‐9 position were synthesized and used for the preparation of blue‐light‐emitting copolyfluorenes ( P1 – P4 ) by the Suzuki coupling polycondensation. The copolymers were characterized by molecular weight determination, elemental analysis, differential scanning calorimeter, thermogravimetric analysis, absorption and emission spectroscopy, cyclic voltammetry, and differential pulse voltammetry. Their decomposition temperatures and glass transition temperatures are 423–441 °C and >120 °C, respectively. In film state, the copolyfluorenes exhibit blue photoluminescence at 425–450 nm, which remains almost unchanged after annealing at 200 °C in air for 60 min. Polymer light‐emitting diodes [ITO/PEDOT:PSS/ P1 – P4 /Ca(50 nm)/Al(100 nm)] show stable blue‐light emission under device operation with the CIE co‐ordinates being between (0.16, 0.07) and (0.17, 0.09). The light‐emitting diodes devices from P1 and P3 containing electron‐deficient oxadiazole units display enhanced performance, with the maximum brightness and maximum current efficiency being (4510 cd/m² and 2.40 cd/A) and (2930 cd/m², 1.19 cd/A), respectively. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 2821–2834, 2009     

Construction of a Hexameric Zn(II)‐metallomacrocycle and its Photo‐ and Electroluminescence Properties: [Zn6(O‐hexyl‐3,5‐bis(2,2′:6′,2″‐terpyridine)phenol)6(BF4)12]

Summary: An O‐hexyl‐3,5‐bis(terpyridine)phenol ligand has been synthesized and transformed into a hexagonal Zn(II)‐metallomacrocycle by a facile self‐assembly procedure capitalizing on terpyridine‐Zn(II)‐terpyridine connectivity. The structural composition was confirmed by NMR and mass spectral techniques; photo‐ and electroluminescence properties were also investigated. The OLED device shows green electroluminescent emission at 515 nm with a maximum luminance of 39 cd · m⁻² and maximum efficiency of 0.16 cd · A⁻¹.

Structure and electroluminescent properties of the metallomacrocycle investigated.     

Synthesis of novel nitrogen‐ and sulfur‐containing conjugated polymers used as hole‐transporting materials for organic light‐emitting diodes

Two series of highly soluble novel nitrogen‐ and sulfur‐containing conjugated polymers were synthesized via an acid‐induced self‐polycondensation of functional monomers with methyl sulfinyl and aromatic groups. The well‐defined structures of synthesized polymers were confirmed by their NMR and IR spectra. The highest occupied molecular orbital energy values for these materials, estimated by cyclic voltammetry, showed a broad range of values from about 5.0 to 5.2 eV used as hole‐transport layers (HTL) in two‐layer light‐emitting diodes ITO/HTL/Alq₃/Mg:Ag [ITO = indium tin oxide, and Alq₃ = tris(8‐quinolinato) aluminum]. The typical turn‐on voltage of these diodes was about 4–5 V. The maximum brightness of the device was about 3440 cd/m² at 20 V. The maximum efficiency was estimated to be 0.15 lm/W at 10 V. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 1321–1333, 2002     

Carbazole end‐capped pyrene starburst with enhanced electrochemical stability and device performance

Carbazole end‐capped starburst molecule based on pyrene core “4CzFP” was synthesized and characterized. The starburst material shows good film‐forming ability and bright blue fluorescence. In cyclic voltammetry test, 4CzFP shows a high highest occupied molecular orbital energy level of ?5.26 eV, indicating it has good hole‐injection ability. The material is quite stable under series of cyclic voltammetry scans, implying its good electrochemical stability. Single‐layered electroluminescent device takes on stable blue emission with a peak current efficiency of 0.84 cd/A. Double‐layered device by adding Poly(N‐vinylcarbazole) (PVK) as a hole‐injection layer does not show any improvement, indicating that 4CzFP could be efficiently used as the hole‐injection/light‐emitting layer. The device performance is largely improved by adding a thin TPBI electron‐injection/transporting layer. The peak efficiency reaches 3.28 cd/A and the maximum brightness is over 2200 cd/m². © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

High‐efficiency blue light‐emitting polymers based on 3,6‐silafluorene and 2,7‐silafluorene

A novel blue‐emitting polymer based on 3,6‐silafluorene and 2,7‐silafluorene was synthesized via the Suzuki polycondensation. The resulting polymers are readily soluble in common organic solvents, such as toluene, xylene, THF, and chloroform. The thermal, electrochemical, photophysical, and electroluminescence properties of the resulting polymers were investigated. The device fabricated from the copolymer with a configuration of ITO/PEDOT:PSS/PVK/polymer/Ba/Al exhibited an external quantum efficiency of 1.95%, a luminous efficiency of 1.69 cd A^?1 and a maximal brightness of 6000 cd m^?2. It has been found that the incorporation of the 3,6‐silafluorene unit into the poly(2,7‐silafluorene) main chain can not only improve the color purity of the devices from the resulting copolymer but also enhance its device efficiency. Moreover, no undesired long‐wavelength green emission was observed in the PL spectra of P36‐27SiF90 compared to that of PFO with a dominating emission at 500–600 nm after thermal annealing at 200 °C for 8 h. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4941–4949, 2007