Electrochemically Prepared Three‐dimensional Porous Nitrogen‐doped Graphene Modified Electrode for Non‐enzymatic Detection of Hydrogen Peroxide

A facile and green electrochemical method for the fabrication of three‐dimensional porous nitrogen‐doped graphene (3DNG) modified electrode was reported. This method embraces two consecutive steps: First, 3D graphene/polypyrrole (ERGO/PPy) composite was prepared by electrochemical co‐deposition of graphene and polypyrrole on a gold foil. Subsequently, the ERGO/PPy composite modified gold electrode was annealed at high temperature. Thus 3DNG modified electrode was obtained. Scanning electron microscopy (SEM), X‐ray photoelectron spectroscopy (XPS) and Raman spectroscopy were used to characterize the structure and morphology of the electrode. The electrode exhibits excellent electroanalytical performance for the reduction of hydrogen peroxide (H₂O₂). By linear sweep voltammetric measurement, the cathodic peak current was linearly proportional to H₂O₂ concentration in the range from 0.6 μM to 2.1 mM with a sensitivity of 1.0 μA μM⁻¹ cm⁻². The detection limit was ascertained to be 0.3 μM. The anti‐interference ability, reproducibility and stability of the electrode were carried out and the electrode was applied to the detection of H₂O₂ in serum sample with recoveries from 98.4 % to 103.2 %.     

Uniform Decoration of Vanadium Oxide Nanocrystals on Reduced Graphene‐Oxide Balls by an Aerosol Process for Lithium‐Ion Battery Cathode Material

VO₂‐decorated reduced graphene balls were prepared by a one‐pot spray‐pyrolysis process from a colloidal spray solution of well‐dispersed graphene oxide and ammonium vanadate. The graphene–VO₂ composite powders prepared directly by spray pyrolysis had poor electrochemical properties. Therefore, the graphene–VO₂ composite powders were transformed into a reduced graphene ball (RGB)–V₂O₅ (RGB) composite by post‐treatment at 300 °C in an air atmosphere. The TEM and dot‐mapping images showed a uniform distribution of V and C components, originating from V₂O₅ and graphene, consisting the composite. The graphene content of the RGB–V₂O₅ composite, measured by thermogravimetric analysis, was approximately 5 wt %. The initial discharge and charge capacities of RGB–V₂O₅ composite were 282 and 280 mA h g^?1, respectively, and the corresponding Coulombic efficiency was approximately 100 %. On the other hand, the initial discharge and charge capacities of macroporous V₂O₅ powders were 205 and 221 mA h g^?1, respectively, and the corresponding Coulombic efficiency was approximately 93 %. The RGB–V₂O₅ composite showed a better rate performance than the macroporous V₂O₅ powders.     

Preparation and Electrochemical Performance of V2O3-C Dual-Layer Coated LiFePO4 by Carbothermic Reduction of V2O5

The V₂O₃-C dual-layer coated LiFePO₄ cathode materials with excellent rate capability and cycling stability were prepared by carbothermic reduction of V₂O₅. X-ray powder diffraction, elemental analyzer, high resolution transmission electron microscopy and Raman spectra revealed that the V₂O₃ phase co-existed with carbon in the coating layer of LiFePO₄ particles and the carbon content reduced without graphitization degree changing after the carbothermic reduction of V₂O₅. The electrochemical measurement results indicated that small amounts of V₂O₃ improved rate capability and cycling stability at elevated temperature of LiFePO₄/C cathode materials. The V₂O₃-C dual-layer coated LiFePO₄ composite with 1wt% vanadium oxide delivered an initial specific capacity of 167 mAh/g at 0.2 C and 129 mAh/g at 5 C as well as excellent cycling stability. Even at elevated temperature of 55 oC, the specific capacity of 151 mAh/g was achieved at 1 C without capacity fading after 100 cycles.     

Improvement of the cycle life of composite xerogel V<Subscript>2</Subscript>O<Subscript>5</Subscript>/C in aqueous LiNO<Subscript>3</Subscript> solution by addition of vinylene carbonate

The xerogel V₂O₅/C composite was synthesized by a sol-gel method, using the suspension of carbon black in the solution of crystalline V₂O₅ in hydrogen peroxide as the precursor solution. The Li⁺ intercalation/deintercalation reactions of the xerogel V₂O₅/C composite, used as an anode material of a two-electrode cell with an aqueous LiNO₃ solution as the electrolyte, was studied before and after the addition of vinylene carbonate (VC). Upon addition of vinylene carbonate in an amount of only l wt %, the coulombic capacity during galvanostatic cycling, instead of commonly observed permanent fade, displayed an initial increase and then a stable plateau.     

Electrospun V2O5 Nanostructures with Controllable Morphology as High‐Performance Cathode Materials for Lithium‐Ion Batteries

Porous V₂O₅ nanotubes, hierarchical V₂O₅ nanofibers, and single‐crystalline V₂O₅ nanobelts were controllably synthesized by using a simple electrospinning technique and subsequent annealing. The mechanism for the formation of these controllable structures was investigated. When tested as the cathode materials in lithium‐ion batteries (LIBs), the as‐formed V₂O₅ nanostructures exhibited a highly reversible capacity, excellent cycling performance, and good rate capacity. In particular, the porous V₂O₅ nanotubes provided short distances for Li⁺‐ion diffusion and large electrode–electrolyte contact areas for high Li⁺‐ion flux across the interface; Moreover, these nanotubes delivered a high power density of 40.2 kW kg^?1 whilst the energy density remained as high as 201 W h kg^?1, which, as one of the highest values measured on V₂O₅‐based cathode materials, could bridge the performance gap between batteries and supercapacitors. Moreover, to the best of our knowledge, this is the first preparation of single‐crystalline V₂O₅ nanobelts by using electrospinning techniques. Interestingly, the beneficial crystal orientation provided improved cycling stability for lithium intercalation. These results demonstrate that further improvement or optimization of electrochemical performance in transition‐metal‐oxide‐based electrode materials could be realized by the design of 1D nanostructures with unique morphologies.     

Flaky Structured V2O5: Morphology,Formation Scheme and Supercapactive Performance

Vanadium pentoxide (V₂O₅) based electrodes for energy storage devices have captured sizeable attention in the past decade owing to their attractive physiochemical features. In the present work, flaky structured V₂O₅ was prepared using a single step hydrothermal route. The results from analytical investigations hold up well with the formation scheme proposed. The flaky morphology of V₂O₅ facilitates additional pathways for electron transport and effective ion access. When employed as a supercapacitor electrode in a neutral electrolyte, this flaky V₂O₅ electrode demonstrates a specific capacitance of 472 F g^?1. Besides, it retains maximum capacitance at higher current density confirming its good rate performance. An asymmetric type supercapacitor using flaky V₂O₅ as positive electrode and activated carbon as negative electrode exhibits specific capacitance of 69 F g^?1. This device shows energy density of 10 W h kg^?1 within the operational window of 1 V.

     

(La0.8Sr0.2)0.9MnO3–Gd0.2Ce0.8O1.9 composite cathodes prepared from (Gd, Ce)(NO3) x -modified (La0.8Sr0.2)0.9MnO3 for intermediate-temperature solid oxide fuel cells

Development of high performance cathodes with low polarization resistance is critical to the success of solid oxide fuel cell (SOFC) development and commercialization. In this paper, (La_0.8Sr_0.2)_0.9MnO₃ (LSM)–Gd_0.2Ce_0.8O_1.9(GDC) composite powder (LSM ~70 wt%, GDC ~30 wt%) was prepared through modification of LSM powder by Gd_0.2Ce_0.8(NO₃) _x solution impregnation, followed by calcination. The electrode polarization resistance of the LSM–GDC cathode prepared from the composite powder was ~0.60 Ω cm² at 750 °C, which is ~13 times lower than that of pure LSM cathode (~8.19 Ω cm² at 750 °C) on YSZ electrolyte substrates. The electrode polarization resistance of the LSM–GDC composite cathode at 700 °C under 500 mA/cm² was ~0.42 Ω cm², which is close to that of pure LSM cathode at 850 °C. Gd_0.2Ce_0.8(NO₃) _x solution impregnation modification not only inhibits the growth of LSM grains during sintering but also increases the triple-phase-boundary (TPB) area through introducing ionic conducting phase (Gd,Ce)O_2-δ, leading to the significant reduction of electrode polarization resistance of LSM cathode.     

Electrochemically Generated γ‐LixV2O5 as Insertion Host for High‐Energy Li‐Ion Capacitors

In this study, we explored the feasibility of using electrochemically generated γ‐Li_xV₂O₅ as an insertion‐type anode in the lithium‐ion capacitor (LIC) with activated carbon (AC) as a cathode. Along with the native form of V₂O₅, their carbon composites are also used as the electrode material which is prepared by high‐energy ball milling. The electrochemical pre‐lithiation strategy is used to generate the desired γ‐phase of V₂O₅ (γ‐Li_xV₂O₅). Under the optimized mass loading conditions, the LICs are assembled with γ‐Li_xV₂O₅ as anode and AC as a cathode in the organic medium. Among the different LICs fabricated, AC/γ‐Li_xV₂O₅‐BM50 configuration delivered an energy density of 33.91 Wh kg^?1 @ 0.22 kW kg^?1 with excellent capacity retention characteristics. However, a dramatic increase in energy density (43.98 Wh kg^?1@0.28 kW kg^?1) is noted after the electrolyte modification with fluoroethylene carbonate. The high temperature performance of the assembled LIC is also studied and found that γ‐Li_xV₂O₅ phase can be used as a potential battery‐type component to construct high‐performance hybrid charge storage devices.     

Electrochemical properties of LiMn2O4 films produced by combustion reaction

Lithium manganese oxide powders were prepared via combustion reaction. Structural characterization of the powder using X-ray diffraction and scanning electron microscopy confirmed the formation of a LiMn₂O₄ nanosized powder. LiMn₂O₄ films were prepared by spin coating using 80 wt% of oxide, 15 wt% of polyaniline (PAni) as an electronic conductor and 5 wt% of polyvinylidene (PVDF) as a binder in N.N.-dimethyl acetamide. A Coulombic efficiency of 96% confirmed the electrochemical stability of the composite. The variation in impedance as a function of the lithium intercalation/deintercalation process reflected the interaction between the oxide and/or polyaniline particles at a high frequency range, and a diffusion tendency was observed at medium and low frequency ranges. The capacity values of the composite electrodes relative to the LiMn₂O₄ mass were 178.6/177.5 and 145/140 mAh g⁻¹ for the first and 25th charge/discharge cycles, respectively.     

Nanobiocomposite Modified Carbon‐Ceramic Electrode Based on Nano‐TiO2‐Plant Tissue and Its Application for Electrocatalytic Oxidation of Dopamine

A new modified carbon‐ceramic electrode was prepared by incorporating TiO₂ nanoparticle into sol‐gel network by accompanying apple tissue. A mixture of fine graphite powder with 15 wt% of TiO₂ nanoparticle was used for the preparation of the carbon matrix and finally modification with a known amount weighted of apple tissue. The apple tissue containing polyphenol oxidase enzyme acts as molecular recognition element. The electrocatalytic oxidation of dopamine was investigated on the surface of the nanobiocomposite modified carbon‐ceramic electrode using cyclic voltammetry, chronoamperometry and amperometry techniques. Effect of pH, scan rate, TiO₂ percentage on the response of modified electrode was studied. The prepared modified electrode presented a linear range for dopamine from 5.0×10^?6 to 1.2×10^?3 M in buffered solutions with pH 7.4 by amperometry. The detection limit was 3.41×10^?6 M dopamine. The response of the modified carbon‐ceramic electrode and unmodified carbon‐ceramic electrode was compared.     

Tris(2,2′‐bipyridyl)ruthenium(II) Electrogenerated Chemiluminescence Sensor Based on Sol–Gel‐Derived V2O5/Nafion Composite Films

Mesoporous V₂O₅/Nafion composite films have been used for the immobilization of tris(2,2′‐bipyridyl)ruthenium (II) (Ru(bpy) ) on an electrode surface to yield a solid‐state electrogenerated chemiluminescence (ECL) sensor. The electrochemical and ECL behavior of Ru(bpy) ion‐exchanged into the composite films has been characterized as a function of the amount of Nafion incorporated into the V₂O₅/Nafion composite. The composite film with 80% Nafion content has the largest pore diameter (4.19 nm) and yields the maximum ECL response for tripropylamine (TPA) because of the fast diffusion of analyte into the film with large pores. Due to the enlarged pore size and enhanced conductivity of the V₂O₅/Nafion composite, the present ECL sensor based on the composite films exhibited around 2 orders of magnitude higher ECL response and one order of magnitude lower detection limit for TPA (10 nM) compared to those obtained with the ECL sensors based on other types of sol–gel ceramic/Nafion composite films such as SiO₂/Nafion and TiO₂/Nafion.     

A new Na+ glass-dispersed Na2CO3 composite for a solid state electrochemical CO2 gas sensor

The electrical conductivity of the 40Na₂O:50SiO₂:10B₂O₃ glass-dispersed Na₂CO₃ composite solid electrolyte system, prepared by liquid phase sintering, is systematically investigated using complex impedance spectroscopy. The unreacted glass glues the Na₂CO₃ grains together, which not only reduces the micropores but also improves the ionic conductivity and mechanical strength of the pellet. The conductivity enhancement in such a composite solid electrolyte system is discussed in the light of the increased concentration of charge carriers in a diffuse space charge layer formed at the crystalline-glass interface. A galvanic CO₂ gas sensor using an optimised composite electrolyte (50 wt% glass-dispersed Na₂CO₃) is found to be more stable against thermal cycles (heating and cooling) vis-à-vis the sensor based on a pure crystalline solid electrolyte. Received: 12 June 1998 / Accepted: 21 October 1998     

Porous nanostructured V2O5 film electrode with excellent Li-ion intercalation properties

Porous nanostructured V₂O₅ films were prepared by electrodeposition from V₂O₅ sol with the addition of block copolymer Pluoronic P123, and they can be readily applied as Li-ion battery cathode without adding any polymer binder or conductive additives. SEM images showed an ideal morphology for Li⁺ intercalation favored charge transfer kinetics, which is a combination of homogeneously distributed nano-pores and V₂O₅ nanoparticles. Electrochemical measurements revealed that, the porous nanostructured V₂O₅ films have a high discharge capacity of 160 mAh/g at 9 A/g, and maintain 240 mAh/g after 40 cycles at 300 mA/g. The excellent Li⁺ intercalation property could be ascribed to the high surface area, sufficient contact between electrode materials and electrolyte, short Li⁺ diffusion path, as well as the good accommodation for volume change which are benefited from homogeneously distributed nano-pores and V₂O₅ nanoparticles.     

Facile one‐step synthesis of electromagnetic functionalized polypyrrole/Fe3O4 nanotubes via a self‐assembly process

This article reports a simple self‐assembly process for facile one‐step synthesis of novel electromagnetic functionalized polypyrrole (PPy)/Fe₃O₄ composite nanotubes using p‐toluenesulfonic acid (p‐TSA) as the dopant and FeCl₃ as the oxidant. The key trick of the present method is to use FeCl₃ as the oxidant for both PPy and Fe₃O₄ in the same time to synthesize PPy/Fe₃O₄ composite nanotubes in one‐step. This facile one‐step method is much simpler than the conventional approach using the Fe₃O₄ nanoparticles as the additives. Compared to the similar composites synthesized using the conventional method, the as‐prepared PPy‐p‐TSA/Fe₃O₄ composite nanotubes using the facile one‐step self‐assembly process show much higher room‐temperature conductivity. Moreover, the composite nanotubes display interesting ferromagnetic behavior. The electrical properties of the PPy‐p‐TSA/Fe₃O₄ composite nanotubes are dominated by the amount of FeCl₃ while their magnetic properties are controlled by the amount of FeCl₂. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 320–326, 2010     

Composite cathode materials Ag-Ba0.5Sr0.5Co0.8Fe0.2O3 for solid oxide fuel cells

Silver-Ba_0.5Sr_0.5Co_0.8Fe_0.2O_3-δ (BSCF) cathodes were prepared in two ways. In the first method, Ag-BSCF composite powder was prepared in ethanol solution, where Ag nanoparticles serving as a component in the preparation of Ag-BSCF composite cathodes had been previously obtained via one-step synthesis in absolute ethanol using a neutral polymer (polyvinylpyrrolidone). To the best of our knowledge, this is the first study to use a Ag sol obtained by the above method for preparation of Ag-BSCF composite powder. Then, a paste containing this powder was screen-printed on a Sm_0.2Ce_0.8O_1.9 electrolyte and sintered at 1,000 °C. In the second technique, an aqueous solution of AgNO₃ was added to a previously sintered BSCF cathode, which was then sintered again at 800 °C. The oxygen reduction reaction at the quasi-point BSCF cathode on the Sm_0.2Ce_0.8O_1.9 electrolyte was tested by electrochemical impedance spectroscopy at different oxygen concentrations in three electrode setup. The continuous decrease of polarization resistance was observed under polarization ?0.5 V at 600 °C. The comparative studies of both obtained composite Ag-BSCF materials were performed in hydrogen-oxygen IT-SOFC involving samaria-doped ceria as an electrolyte and Ni-Gd_0.2Ce_0.8O_1.9 anode. In both cases, the addition of silver to the cathode caused an increase in current and power density compared with an IT-SOFC built with the same components but involving a monophase BSFC cathode material.     

Plasma Modified V2O5/PEDOT Hybrid Based Flexible Electrochromic Devices

Vanadium oxide/poly (3,4‐ ethylenedioxythiophene)(V₂O₅‐PEDOT) hybrid materials were prepared in a rotating quartz plasma reactor via capacitively coupled radio frequency (RF 13.56 MHz) plasma. Thin films of V₂O₅‐PEDOT hybrid and V₂O₅ were obtained by electron beam evaporation technique onto flexible PET substrate for electrochromic devices (ECDs) applications. As a counter electrode, both RF magnetron sputtered MoO₃ onto ITO coated PET and only ITO coated PET electrodes were used. Characterizations of the films were carried out via using scanning electron microscopy‐energy dispersive X‐ray spectroscopy (SEM‐EDX) and X‐ray diffraction (XRD). Hybrid ECDs results showed that synergistic effect depending on improved stability between V₂O₅ and PEDOT. As a result, we developed all solid complementary electrochromic devices including V₂O₅, V₂O₅‐PEDOT and MoO₃ films. The electrochromic device characteristics such as electrochromic contrast, coloration efficiency, switching time were calculated from optical and electrochemical measurements. The highest coloration efficiency and optical contrast were obtained as 53 cm²/C and 17 % for V₂O₅‐PEDOT/MoO₃‐based ECD.     

Synthesis, characterization and activity in cyclohexene epoxidation of V2O5–TiO2 anatase xerogel

The system of V₂O₅?CTiO₂ catalysts with V₂O₅ contents from 5 to 20 wt% were prepared by the sol?Cgel route and calcined at 500?°C. The mixed oxide series presented the crystalline structure of TiO₂ anatase phase. BET analysis showed a medium surface area decreasing from 73 to 19?m² g^?1 when V₂O₅ content rose from 5 to 20 wt%. The results of pyridine adsorption followed by FT-IR indicate that the catalysts display identical surface acid densities, independently of the V₂O₅ content, and both Br?nsted and Lewis acid sites are present on their surfaces. The V₂O₅ system presents an activity and selectivity during the cyclohexene oxidation reaction. The presence of V₂O₅ increases the catalyst efficiency and leads to a selectivity change from cyclohexenol (blank test) to epoxide, with a maximum for 15 wt% V₂O₅. The conversion of cyclohexene was 46?% while the selectivity to epoxide was higher (75?%).     

Radar Absorption Properties of Ni0.5Zn0.5Fe2O4/PANI/epoxy Nanocomposites

A nitrate? citrate gel was prepared from metallic nitrates and citric acid by sol? gel process and was further used to synthesize Ni_0.5Zn_0.5Fe₂O₄ nanocrystalline powder by auto‐combustion. Then, two novel 15 and 35% (w/w) magnetic Ni_0.5Zn_0.5Fe₂O₄ containing polyaniline nanocomposites, named as PANI‐Ni15 and PANI‐Ni35, respectively, were prepared via in‐situ polymerization of aniline in an aqueous solution containing proper amount of Ni_0.5Zn_0.5Fe₂O₄ magnetic powder. The incorporation of the nanopowders to PANI matrix was confirmed by X‐ray diffraction (XRD), IR and SEM. Synthesized PANI‐NiZn ferrite composite particles were subsequently added to an epoxy resin matrix to produce related nanocomposites. The morphological properties of these nanocomposite materials were investigated by SEM and TEM. The electromagnetic‐absorbing properties were studied by measuring the reflection loss in the frequency range of 8.0 to 12.0 GHz. Results showed the reflection loss of the PANI‐Ni35 composite is higher than pure polyaniline and PANI‐Ni15. The good reflection loss of the nanocomposites suggests their potential applicability as radar absorber.     

Bifunctional Reduced Graphene Oxide/V2O5 Composite Hydrogel: Fabrication,High Performance as Electromagnetic Wave Absorbent and Supercapacitor

Multifunctional graphene hydrogels have attracted great attention aimed at practical applications. Herein, the novel and bifunctional composite hydrogel containing reduced graphene‐oxide nanosheets (RGO) and V₂O₅ nanobelts (RGO/V₂O₅) is successfully prepared for the first time. Surprisingly, tridimensional (3D) RGO/V₂O₅ composite hydrogels cannot only be used as high‐performance electromagnetic (EM) wave absorbents; they also exhibit excellent properties suitable for supercapacitor electrodes. The composites exhibit a maximum absorption of up to ?21.5 dB. In particular, a composite hydrogel showed a bandwidth of 6.63 GHz, corresponding to a reflection loss at ?10 dB, which opens the possibility for the use of 3D graphene with other functional nanomaterials as lightweight and high‐performance EM wave absorption materials. Remarkably, the composite hydrogel is capable of delivering a high specific capacitance of about 320 F g^?1 at a current density of 1.0 A g^?1.