Controlled radical polymerization of styrene in the presence of cyclic 1,2‐disulfides

The thermal polymerization of styrene (St) in the presence of cyclic 1,2‐disulfides at 120 °C was investigated. In the polymerization of St in the presence of 1,2‐dithiane (DT), that is, six‐member cyclic 1,2‐disulfide, the polymer yields and molecular weights increased with the reaction time. The linear relation between the polymer yields and molecular weights was observed, and the line passed through an original point. The molecular weight distributions of the polymers remained almost constant but were not narrow. For this polymerization with a living nature, we proposed the following mechanism: the propagating St radical reacted with thiyl radicals derived from DT, leading to the formation of dormant species, and the formed C S bond of the dormant was dissociated again to give the propagating polystyryl radical and thiyl radical. Similar results were obtained in the thermal polymerization of St at 120 °C in the presence of 1,2‐dithiacycloheptane, that is, seven‐member cyclic 1,2‐disulfide. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 145–151, 2001     

End‐group fidelity of copper(0)‐meditated radical polymerization at high monomer conversion: an ESI‐MS investigation

Copper(0)‐mediated radical polymerization (single electron transfer‐living radical polymerization) is an efficient polymerization technique that allows control over the polymerization of acrylates, vinyl chloride and other monomers, yielding bromide terminated polymer. In this contribution, we investigate the evolution of the end‐group fidelity at very high conversion both in the presence and in the absence of initially added copper (II) bromide (CuBr₂). High resolution electrospray‐ionization mass spectroscopy (ESI‐MS) allows determination of the precise chemical structure of the dead polymers formed during the polymerization to very high monomer conversion, including post polymerization conditions. Two different regimes can be identified via ESI‐MS analysis. During the polymerization, dead polymer results mainly from termination via disproportionation, whereas at very high conversion (or in the absence of monomer, that is, post‐polymerization), dead polymers are predominantly generated by chain transfer reactions (presumably to ligand). The addition of CuBr₂ significantly reduces the extent of termination by both chain transfer and disproportionation, at very high monomer conversion and under post‐polymerization conditions, offering a convenient approach to maintaining high end‐group fidelity in Cu(0)‐mediated radical polymerization. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Thermodynamics of addition polymerization

Addition polymerizations of both acyclic and cyclic monomers show the characteristic features of any aggregation process, in particular, a ceiling temperature above which the formation of the aggregate (long‐chain polymer), under given conditions of monomer concentration, solvent, and pressure, would involve a positive change of free energy and is therefore impossible. Conversely, for a given temperature, pressure, and solvent, there is an equilibrium monomer concentration below which long‐chain polymer cannot be formed. Monomers must therefore have a negative free energy of polymerization, under given conditions, if they are to be capable of undergoing a significant extent of polymerization. The effect of monomer structure, including ring size, on thermodynamic polymerizability is discussed, as well as the possibility of copolymerizing monomers that cannot themselves give homopolymers. Examples are given for various possible mechanisms of polymerization. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 2137–2146, 2000     

Polymer having a trithiocarbonate moiety in the main chain: Application to reversible addition–fragmentation chain transfer controlled thermal and photoinduced monomer insertion polymerizations

A polymer having a trithiocarbonate moiety in its main chain was synthesized with a cyclic, five‐membered dithiocarbonate as a building block. The trithiocarbonate in the polymer acted as a reversible addition–fragmentation chain transfer reagent to mediate a controlled insertion polymerization of styrene into the polymer main chain, giving the corresponding sequence‐ordered polymer having a well‐defined polystyrene segment in the main chain. During the polymerization, the polystyrene segment in the main chain gained its molecular weight, which maintained a linear relationship with the conversion of styrene. The insertion polymerization of styrene was induced not only thermally but also by ultraviolet irradiation. This photoinduced polymerization was well controlled by the trithiocarbonate moiety to give the corresponding polymer, whose structure was virtually the same as that obtained by the thermal polymerization. © 2006 Wiley Periodicals, Inc. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 6324–6331, 2006     

Polymerization of epoxidized vegetable oil derivatives: Ionic‐coordinative polymerization of methylepoxyoleate

Ring‐opening polymerization of epoxidized methyloleate (EMO) with various ionic‐coordinative initiators have been studied and compared with other internal epoxy monomers: benzyl 9,10‐epoxyoleoylether and cis‐4,5‐epoxyoctane. The structure and molecular weight of the resulting polymers have been studied by ¹H‐ and ¹³C‐NMR, MALDI‐TOF‐MS, and size exclusion chromatography analysis. Polymers with higher molecular weight than those obtained with conventional cationic catalyst are obtained. These materials have been found to consist of a complex mixture of cyclic and linear polymer chains with different chain ends that can be related to the catalyst nature and the occurrence of two main polymerization mechanisms, the cationic and the ionic‐coordinative. In the polymerization of EMO, transesterification by‐side reactions leading to ester linkages in the main chain have been identified. These undesired reactions have been suppressed by copolymerization with small amounts of tetrahydrofuran with no substantial decrease in the polymer yield and molecular weight. Finally, the polymerization of EMO has been tested in a larger scale to prepare a renewable resource‐based polyether as starting material to produce polyether polyols for polyurethane applications. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Ring‐opening polymerization of lipoic acid and characterization of the polymer

Thermal polymerization of DL ‐α‐lipoic acid (LPA) in bulk without any initiator proceeded easily above the melting point of LPA. The molecular weight polymer determined by GPC was high. From the ¹H NMR spectra of polymers, poly(LPA) obtained from polymerization of high purity LPA was to consist of cyclic structures, which was confirmed by ESI‐MS. Interlocked polymer consisting of poly(LPA) and dibenzo‐30‐crown‐10 entangled with each other was synthesized by the polymerization of LPA in the presence of dibenzo‐30‐crown‐10. From the DSC analysis of the polymers, glass transition temperature was estimated to be about ?11 °C, but melting point was not observed, indicating that poly(LPA) is an amorphous polymer. By photodecomposition of poly(LPA), M_n was rapidly decreased at the early stage of the decomposition. After that, the M_n of the polymer kept and then was almost constant even for a prolonged reaction time. On the basis of the results, it would be presumed that poly (LPA) obtained form polymerization of high purity LPA includes an interlocked structure. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Synthesis and properties of an ionic polyacetylene with aromatic heterocycles

A new ionic polyacetylene with two aromatic heterocycles (pyridyl and thienyl) was prepared by the activation polymerization of 2‐ethynylpyridine by using 3‐(6‐bromohexyloxy)methylthiophene without any additional initiator or catalyst. The activated acetylenic triple bond of N‐substituted‐2‐ethynylpyridinium bromide, formed at first quaternarization process, was susceptible to linear polymerization. The instrumental analysis data on the polymer structure revealed that the polymer have the conjugated polyene backbone structure with the designed two aromatic heterocycles. The photoluminescence peak is located at 510 nm corresponding to a photon energy of 2.43eV. The electrochemical properties of this ionic polyacetylene were also measured and discussed. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5679–5685, 2007     

Pendant cyclic carbonate‐polymer/Na‐smectite nanocomposites via in situ intercalative polymerization and solution intercalation

Nanocomposites of sodium smectite with polyether‐ and polystyrene‐containing pendant cyclic carbonates offer a novel approach to improving hydraulic barrier properties of Na‐smectite liners to saline leachates. The cyclic carbonate polyethers were prepared by cationic ring opening polymerization of a cyclic carbonate‐containing epoxide, whilst polystyrene polymers having pendant cyclic carbonate groups were obtained from radical photopolymerization of styrene. Na‐smectite nanocomposites of these polymers were formed via clay in situ polymerization and solution intercalation methods. X‐ray diffraction (XRD) and FT‐IR analysis confirmed that the polyether can be intercalated within the layers of smectite via in situ as well as solution intercalation of the pre‐formed polymer. The cyclic carbonate polyether nanocomposite was more resistant to leaching in 3M aqueous sodium chloride than its respective cyclic carbonate. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 2421–2429     

Spontaneous crosslinking of poly(1,5‐dioxepan‐2‐one) originating from ether bond fragmentation

The spontaneous reaction of unsaturated double bonds induced by the fragmentation of ether bonds is presented as a method to obtain a crosslinked polymer material. Poly(1,5‐dioxepan‐2‐one) (PDXO) was synthesized using three different polymerization techniques to investigate the influence of the synthesis conditions on the ether bond fragmentation. It was found that thermal fragmentation of the ether bonds in the polymer main chain occurred when the synthesis temperature was 140 °C or higher. The double bonds produced reacted spontaneously to form crosslinks between the polymer chains. The formation of a network structure was confirmed by Fourier transform infrared spectrometry and differential scanning calorimetry. In addition, the low molar mass species released during hydrolysis of the DXO polymers were monitored by ESI‐MS and MALDI‐TOF‐MS. Ether bond fragmentation also occurred during the ionization in the electrospray instrument, but predominantly in the lower mass region. No fragmentation took place during MALDI ionization, but it was possible to detect water‐soluble DXO oligomers with a molar mass up to approximately 5000 g/mol. The results show that ether bond fragmentation can be used to form a network structure of PDXO. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 7258–7267, 2008     

The synthesis of cyclic polymers by olefin metathesis: Achievements and challenges

Cyclic polymers have drawn considerable interest for their peculiar physical properties in comparison to linear polymers, despite their equivalent compositions. Synthetically, cyclic polymers can be accessed through either macrocyclic ring‐closure or by ring‐expansion polymerization, but the main challenge with either method is the production of highly pure cyclic polymer samples. This highlight describes advances in the area of cyclic polymer synthesis, with a particular focus on ring‐expansion metathesis polymerization. Methods for characterizing cyclic polymers and assessing their purity are also discussed in order to emphasize the need for additional robust and reliable methods for synthesizing and studying topologically complex macromolecules. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019 , 57, 228–242     

Controlled ring‐opening polymerization of L‐lactide and 1,5‐dioxepan‐2‐one forming a triblock copolymer

Novel elastomeric A‐B‐A triblock copolymers were successfully synthesized in a new two‐step process: controlled ring‐opening polymerization of the cyclic ether–ester 1,5‐dioxepan‐2‐one as the amorphous middle block (B‐block) followed by addition and polymerization of the two semicrystalline L ‐lactide blocks (A‐block). A 1,1,6,6‐tetra‐n‐butyl‐1,6‐distanna‐2,5,7,10‐tetraoxacyclodecane initiator system was utilized and the reaction was performed in chloroform at 60 °C. A good control of the synthesis was obtained, resulting in well defined triblock copolymers. The molecular weight and chemical composition were easily adjusted by the monomer‐to‐initiator ratio. The triblock copolymers formed exhibited semicrystallinity up to a content of 1,5‐dioxepan‐2‐one as high as 89% as determined by differential scanning calorimetry. WAXS investigation of the triblock copolymers showed a crystal structure similar to that of the pure poly(L ‐lactide). © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 1774–1784, 2000     

Environmental stress cracking resistance of polyethylene: The use of CRYSTAF and SEC to establish structure–property relationships

Nineteen commercial high‐density polyethylene resins made with different polymerization processes and catalyst types were analyzed by high‐temperature size exclusion chromatography and crystallization analysis fractionation. The information obtained with these characterization techniques on the polymer chain structure was correlated to environmental stress cracking resistance. Environmental stress cracking resistance increases when the molecular weight and concentration of polymer chains that crystallize in trichlorobenzene between 75 and 85 °C increase. Polymer chains present in this crystallization range are assumed to act as tie molecules between crystal lamellae. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 1267–1275, 2000     

Well‐defined polycaprolactone precursors for low surface‐energy polyurethane films

For the purpose of developing model coating systems, it is important to use well‐defined coating precursors. In this work, polyester oligomers were synthesized by controlled ring‐opening polymerization of ε‐caprolactone and 4‐tert‐butyl‐ε‐caprolactone via an activated monomer mechanism. These well‐defined oligomers, including 3‐armed hydroxyl‐functionalized polyesters and perfluoroalkyl‐end‐capped linear polyesters, have been obtained with controlled functionality and low‐molecular weight polydispersity and without the formation of cyclic structures, as demonstrated by MALDI‐ToF MS analyses. The polymer architecture and functionality can be tuned by using different initiating alcohols. These oligomers have been used as precursors to prepare model low surface‐energy polyurethane coatings. Upon the addition of about 1 wt % of fluorine in the polyurethane films, the advancing contact angles for water and hexadecane have been increased to 105° and 78°, respectively; the surface enrichment of fluorinated species has been confirmed by X‐ray photoelectron spectroscopy. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 218–227, 2008     

Synthesis and characterization of a novel reactive ladderlike 4,4′‐phenylene ether‐bridged polyvinylsiloxane

A novel soluble, reactive ladderlike 4,4′‐phenylene ether‐bridged polyvinylsiloxane (L) was synthesized successfully for the first time by a stepwise coupling polymerization (SCP) including hydrolysis and polycondensation. The monomer, 4,4′‐bis(vinyldimethoxysilyl)phenylene ether (M), was synthesized by Grignard reaction. The structures of the monomer and the polymer were characterized by infrared spectrometry (IR), nuclear magnetic resonance (¹H NMR, ¹³C NMR, ²⁹Si NMR), mass spectrometry (MS), differential scanning calorimetry (DSC), X‐ray diffraction (XRD), and gel permeation chromatography (GPC). It is proposed from the characterization data that the polymer possesses an ordered ladderlike structure. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 2702–2710, 2000     

Cross‐linking photopolymerization of monoacrylate initiated by benzophenone

The chain‐end structure of the photopolymerized acrylate using benzophenone as an initiator was investigated as well as polymerization behavior. Dodecyl acrylate was used as a monomer in this study. Gelation occurred during ultraviolet (UV) irradiation, whereas a cross‐linker was not employed. Conversion‐time profile below gel point gave a linear first‐order plot suggesting that the steady‐state was held throughout polymerization. Matrix‐assisted laser desorption/ionization time‐of‐flight mass spectra of the resultant polymer indicated that most polymers had an acryloyl group at one of the chain‐ends, while some polymers had an acryloyl group at each chain‐end. The cross‐linking reaction leading to gelation would have been caused by the subsequent copolymerization of the residual monomer with the latter polymer having two acryloyl groups. Dissolved oxygen in the monomer solution influenced the polymer structure giving hydroxyl group at chain‐end. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 1545–1553     

Solid‐phase thermal polymerization of macrocyclic ethylene terephthalate dimer using various transesterification catalysts

Thermal ring‐opening polymerization of a uniform macrocyclic ethylene terephthalate dimer with and without catalyst was investigated for the first time. Although polymerization progressed without a catalyst, the reaction was extremely slow and all the products were colored. Various transesterification catalysts were tested for their activity toward this ring‐opening polymerization. Among the various catalysts, 1,3‐dichloro‐1,1,3,3‐tetrabutyldistannoxane exhibited the highest catalytic activity, and a colorless polymer with a weight‐average molecular weight of 36,100 was obtained in 100% yield by heating for 3 min at 200 °C. It is noteworthy that our method does not need a vacuum because no side products are formed during the process. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 3360–3368, 2000     

Polypeptoids: A perfect match for molecular definition and macromolecular engineering?

Precision synthesis of polymers has been a hot topic in recent years. While this is notoriously difficult to address for polymers with a C? C backbone, Merrifield has discovered a way many decades ago for polypeptides. Using a similar approach, N‐substituted polypeptides, so‐called polypeptoids have been synthesized and studied for about 20 years. In contrast, the living ring‐opening polymerization (ROP) of N‐substituted N‐carboxyanhydrides was among the first living polymerizations to be discovered. More recently, a surge in new synthetic approaches led to the efficient synthesis of cyclic or linear multiblock copolypeptoids. Thus, polypeptoids can be synthesized either by solid phase synthesis to yield complex and exactly defined oligo‐ and small polymers or by ROP of appropriately N‐substituted N‐carboxyanhydrides (NNCA) to give linear, cyclic, or star‐like polymers. Together with an excellent biocompatibility, this polymer family may have a bright future ahead as biomaterials. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013, 51, 2731–2752     

Tadpole‐shaped amphiphilic copolymers prepared via RAFT polymerization and click reaction

The tadpole‐shaped amphiphilic copolymers with cyclic polystyrene as the head and a linear poly(N‐isopropylacrylamide) as the tail have been successfully synthesized by combination of reversible addition‐fragmentation chain transfer (RAFT) polymerization and “click” reaction. The synthesis involves two main steps: (1) preparation of a linear acetylene‐terminated PNIPAAM‐b‐PS with a side azido group anchored at the junction between two blocks; (2) intramolecular cyclization reaction to produce the cyclic PS block using “click” chemistry under high dilution. The structures, molecular weights, and molecular weight distributions of the resulted intermediates and the target polymers were characterized by their ¹H NMR, FTIR, and gel permeation chromatography. The difference of surface property between tadpole‐shaped polymer and its linear precursor was observed, and the water contact angles on the former surface are larger than that of the latter surface. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 2390–2401, 2008     

Ring‐opening polymerization of ε‐caprolactone and L‐lactide from silica nanoparticles surface

Coating of silica nanoparticles by biocompatible and biodegradable polymers of ε‐caprolactone and L ‐lactide was performed in situ by ring‐opening polymerization of the cyclic monomers with aluminum, yttrium, and tin alkoxides as catalysts. Hydroxyl groups were introduced on the silica surface by grafting of a prehydrolyzed 3‐glycidoxypropyl trimethoxysilane to initiate a catalytic polymerization in the presence of metal alkoxides. In this manner, free polymer chains were formed to grafted ones, and the graft density was controlled by the nature of the metal and the alcohol‐to‐metal ratio. The grafting reaction was extensively characterized by spectroscopic techniques and quantified. Nanocomposites containing up to 96% of polymer were obtained by this technique. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 1976–1984, 2004