Synthesis and characterization of novel thermoresponsive‐co‐biodegradable hydrogels composed of N‐isopropylacrylamide,poly(L‐lactic acid), and dextran

A series of novel multifunctional hydrogels that combined the merits of both thermoresponsive and biodegradable polymeric materials were designed, synthesized, and characterized. The hydrogels were copolymeric networks composed of N‐isopropylacrylamide (NIPAAM) as a thermoresponsive component, poly(L‐lactic acid) (PLLA) as a hydrolytically degradable and hydrophobic component, and dextran as an enzymatically degradable and hydrophilic component. The chemical structures of the hydrogels were characterized by an attenuated total reflection–Fourier transform infrared spectroscopy (ATR–FTIR) technique. The hydrogels were thermoresponsive, showing a lower critical solution temperature (LCST) at approximately 32 °C, and their swelling properties strongly depended on temperature changes, the balance of the hydrophilic/hydrophobic components, and the degradation of the PLLA component. The degradation of the hydrogels caused by hydrolytic cleavage of ester bonds in the PLLA component was faster at 25 °C below the LCST than at 37 °C above the LCST, determined by the ATR–FTIR technique. Due to their multifunctional properties, the designed hydrogels show great potential for biomedical applications, including drug delivery and tissue engineering. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5054–5066, 2004     

一种光响应性热敏聚合物的合成及性能表征

合成了偶氮单体 2 [4 (4′ 乙氧基苯基偶氮 )苯氧基 ]乙基丙烯酸酯 (EAPEA) ,利用核磁共振、傅立叶红外和元素分析法对其分子结构进行了表征 .利用该单体与异丙基丙烯酰胺共聚得到一种对温度和光敏感的共聚物 .共聚物中少量的EAPEA单元能够显著降低聚异丙基丙烯酰胺 (PNIPA)的相转变温度 .当EAPEA的摩尔含量为 2 94%时 ,相转变温度从PNIPA均聚物的 31 8℃下降为 2 2 0℃ .在波长为 36 5nm的紫外光照射下 ,共聚物中的偶氮基团能够从反式构型转变为顺式构型 .在紫外光下照 30s后 ,EAPEA摩尔含量为 0 98%的聚 {异丙基丙烯酰胺 共 2 [4 (4′ 乙氧基苯基偶氮 )苯氧基 ]乙基丙烯酸酯 }的相转变温度从 2 7 2℃上升到2 9 3℃     

Introduction of pH‐sensitivity into mechanically strong nanoclay composite hydrogels based on N‐isopropylacrylamide

pH‐sensitive nanoclay composite hydrogels based on N‐isopropylacrylamide (NIPA) were synthesized by copolymerization with cationic and anionic comonomers. Laponite nanoclay particles served as multifunctional crosslinkers, producing hydrogels with exceptionally high mechanical strengths, as measured by elongation at break. Cationic copolymer gels based on NIPA and dimethylaminoethylmethacrylate were prepared by aqueous free radical polymerization, adopting a procedure reported by Haraguchi (Adv Mater 2002, 14, 1120–1124). Without modification, this technique failed to produce anionic copolymer gels of NIPA and methacrylic acid (MAA), due to flocculation of clay particles. Three methods were conceived to incorporate acidic MAA into nanoclay hydrogels. First, NIPA was copolymerized with sodium methacrylate under dilute conditions, producing hydrogels with good pH‐sensitivity but weak mechanical characteristics. Second, NIPA was copolymerized with methyl methacrylate, which was then hydrolyzed to generate acid sidegroups, yielding hydrogels that were much stronger but less pH sensitive. Third, NIPA was copolymerized with MAA following modification of the nanoclay surface with pyrophosphate ions. The resulting hydrogels exhibited both strong pH‐sensitivities at 37 °C and excellent tensile properties. Optical transparency changed during polymerization, depending on hydrophobicity of the components. This work increases the diversity and functionality of nanoclay hydrogels, which display certain mechanical advantages over conventionally crosslinked hydrogels. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 6630–6640, 2008     

A simple FTIR spectroscopic method for the determination of the lower critical solution temperature of N‐isopropylacrylamide copolymers and related hydrogels

Linear and crosslinked polymers based on N‐isopropylacrylamide (NIPAAm) exhibit unusual thermal properties. Aqueous solutions of poly(N‐isopropylacrylamide) (PNIPAAm) phase‐separate upon heating above a lower critical solution temperature (LCST), whereas related hydrogels undergo a swelling–shrinking transition at an LCST. A linear copolymer made of NIPAAm/acryloxysuccinimide (98/2 mol/mol) and two hydrogels with different hydrophilicities were prepared. Fourier transform infrared (FTIR) spectroscopy was employed to determine the transition temperature and provide insights into the molecular details of the transition via probing of characteristic bands as a function of temperature. The FTIR spectroscopy method described here allowed the determination of the transition temperature for both the linear and crosslinked polymers. The transition temperatures for PNIPAAm and the gel resulting from the crosslinking with polylysine or N,N′‐methylenebisacrylamide (MBA) were in the same range, 30–35 °C. For the gels, the transition temperature increased with the hydrophilicity of the polymer matrix. The spectral changes observed at the LCST were similar for the free chains and the hydrogels, implying a similar molecular reorganization during the transition. The C H stretching region suggests that the N‐isopropyl groups and the backbone both underwent conformational changes and became more ordered upon heating above the LCST. An analysis of the amide I band suggests that the amide groups of the linear polymer were mainly involved in hydrogen bonding with water molecules below the LCST, the chain being flexible and disordered in a water solution. During the transition, around 20% of these intermolecular hydrogen bonds between the polymer and water were broken and replaced by intramolecular hydrogen bonds. Similar changes were also observed at the LCST of a gel crosslinked with MBA. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 907–915, 2000     

Preparation,morphology, and thermoresponsive properties of poly(N‐isopropylacrylamide)‐based copolymer microgels

In this research, thermoresponsive copolymer latex particles with an average diameter of about 200–500 nm were prepared via surfactant‐free emulsion polymerization. The thermoresponsive properties of these particles were designed by the addition of hydrophilic monomers [acrylic acid (AA) and sodium acrylate (SA)] to copolymerize with N‐isopropylacrylamide (NIPAAm). The effects of the comonomers and composition on the synthesis mechanism, kinetics, particle size, morphology, and thermoresponsive properties of the copolymer latex were also studied to determine the relationships between the synthesis conditions, the particle morphology, and the thermoresponsive properties. The results showed that the addition of hydrophilic AA or SA affected the mechanism and kinetics of polymerization. The lower critical solution temperature (LCST) of the latex copolymerized with AA rose to a higher temperature. However, because the strong hydrophilic and ionic properties of SA caused a core–shell structure, where NIPAAm was in the inner core and SA was in the outer shell, the LCST of the latex copolymerized with SA was still the same as that of pure poly(N‐isopropylacrylamide) latex. It was concluded that these submicrometer copolymer latex particles with different thermoresponsive properties could be applied in many fields. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 356–370, 2006     

疏水改性智能水凝胶P(NIPA-co-DiAB)的合成及其温敏行为

以N-异丙基丙烯酰胺(NIPA)和N,N-双烯丙基苄胺(DiAB)为共聚单体、N,N-亚甲基双丙烯酰胺(BIS)为交联剂、十二烷基硫酸钠(SDS)为表面活性剂、过硫酸铵(APS)-四甲基乙二胺(TMEDA)为氧化还原引发体系,采用自由胶束交联共聚法合成了疏水基团为芳香基的疏水改性温敏性智能水凝胶P(NIPA-co-DiAB)。研究了DiAB摩尔分数(x(DiAB))对水凝胶溶胀性能的影响。 在初始溶胀阶段,随着x(DiAB)由0增大至3%,P(NIPA-co-DiAB)水凝胶的溶胀行为由Fickian扩散转变为non-Fickian扩散。x(DiAB)分别为0、1%、2%和3%时,P(NIPA-co-DiAB)水凝胶的平衡溶胀率SR0在蒸馏水中分别为63.6、93.5、141.6和167.4,在0.01 mol/L SDS溶液中分别为63.1、71.0、59.0和77.5,在CTAB溶液中分别为37.6、42.2、44.1和60.0,在Triton X-100溶液中分别为30.9、49.4、68.5和88.3。 结果表明,P(NIPA-co-DiAB)水凝胶的(SR0)大于PNIPA水凝胶,且在蒸馏中比在0.01 mol/L表面活性剂溶液中要大。 加入0.01 mol/L Triton X-100、CTAB或SDS后,PNIPA水凝胶的体积相变温度或较低临界溶解温度(LCST)由32.5 ℃分别增加至35.4、45.6和80 ℃。P(NIPA-co-DiAB)水凝胶的LCST由32.0～32.5 ℃分别增加至34.7～35.6 ℃、45.8~46.2 ℃和80 ℃。 加入表面活性剂能增加P(NIPA-co-DiAB)水凝胶的体积相变温度,高的体积相变温度与DiAB含量无关。     

Temperature‐induced aggregation of the copolymers of N‐isopropylacrylamide and sodium 2‐acrylamido‐2‐methyl‐1‐propanesulphonate in aqueous solutions

A series of random copolymers of N‐isopropylacrylamide (NIPAM) and sodium 2‐acrylamido‐2‐methyl‐1‐propanesulphonate (AMPS) was synthesized by free‐radical copolymerization. The content of AMPS in the copolymers ranged from 1.1 to 9.6 mol %. The lower critical‐solution temperature (LCST) of copolymers in water increased strongly with an increasing content of AMPS. The influence of polymer concentration on the LCST of the copolymers was studied. For the copolymers with a higher AMPS content, the LCST decreased faster with an increasing concentration than for copolymers with a low content of AMPS. For a copolymer containing 1.1 mol % of AMPS the LCST dropped by about 3 °C when the concentration increased from 1 to 10 g/L, whereas for a copolymer containing 9.6 mol % of AMPS the LCST dropped by about 10 °C in the concentration range from 2 to 10 g/L. It was observed that the ionic strength of the aqueous polymer solution very strongly influences the LCST. This effect was most visible for the copolymer with the highest content of AMPS (9.6 mol %) for which an increase in the ionic strength from 0.2 to 2.0 resulted in a decrease in the LCST by about 27 °C (from 55 to 28 °C), whereas for the copolymer containing 1.1 mol % of AMPS the LCST decreased only by about 6 °C (from 37 to 31 °C) when the ionic strength increased from 0.005 to 0.3. The reactivity ratios for the AMPS and NIPAM monomer pairs were determined using different methods. The values of r_AMPS and r_NIPAM obtained were 11.0–11.6 and 2.1–2.4, respectively. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 2784–2792, 2001     

Syntheses and Studies of PEG-b-PNIPA Block Polymers

ＳｙｎｔｈｅｓｅｓａｎｄＳｔｕｄｉｅｓｏｆＰＥＧ┐ｂ┐ＰＮＩＰＡＢｌｏｃｋＰｏｌｙｍｅｒｓＣＡＯＷｅｉ－ｘｉａｏ＊＊ａｎｄＺＨＡＮＧＴａｏ（ＣｏｌｅｇｅｏｆＣｈｅｍｉｓｔｒｙａｎｄＭｏｌｅｃｕｌａｒＥｎｇｉｎｅｒｉｎｇ，ＰｅｋｉｎｇＵｎｉｖｅｒｓｉｔ...     

Preparation and properties of poly(N‐isopropylacrylamide)/poly(N‐isopropylacrylamide) interpenetrating polymer networks for drug delivery

A novel poly(N‐isopropylacrylamide) (PNIPA)/PNIPA interpenetrating polymer network (IPN) was synthesized and characterized. In comparison with conventional PNIPA hydrogels, the shrinking rate of the IPN hydrogel increased when gels, swollen at 20 °C, were immersed in 50 °C water. The phase‐transition temperature of the IPN gel remained unchangeable because of the same chemical constituent in the PNIPA gel. The reswelling kinetics were slower than those of the PNIPA hydrogel because of the higher crosslinking density of the IPN hydrogel. The IPN hydrogel had better mechanical strength because of its higher crosslinking density and polymer volume fraction. The release behavior of 5‐fluorouracil (5‐Fu) from the IPN hydrogel showed that, at a lower temperature, the release of 5‐Fu was controlled by the diffusion of water molecules in the gel network. At a higher temperature, 5‐Fu inside the gel could not diffuse into the medium after a burst release caused by the release of the drug on the surface of the gel. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 1249–1254, 2004     

Chemically Crosslinked pH- and Temperature-Sensitive (N-isopropylacrylamide-co-1-vinyl-2-pyrrolidone) Based on New Crosslinker: I. Swelling Behavior

Novel pH- and temperature-sensitive polymer matrices based on N-isopropylacrylamide have been developed. The hydrogels were prepared by bulk radical polymerization of N-isopropylacrylamide and 1-vinyl-2-pyrrolidinone in appropriate amounts of distilled water using different mol% of traditional N,N-methylene bisacrylamide (MBA) and the new synthesized N,N,N-tris acryloyl melamine (MAAm) crosslinkers. Lower critical solution transition temperatures (LCST) were measured by differential scanning calorimetry. The synthesized hydrogels have LCST lower than 40°C. The influence of environmental conditions such as temperature and pH on the swelling behavior of these polymeric gels was investigated. The swelling behaviors of the resulting gels show pH sensitivity. The crosslinked NIPAAm/VP with MAAm hydrogels exhibited more rapid deswelling rate than NIPAAm/VP hydrogels crosslinked with MBA in pure water in response to abrupt temperature changes from 20°C to 50°C.     

β‐Cyclodextrin hydrogel incorporating hydrophobically modified poly(N‐isopropylacrylamide) for a temperature‐dependent release

Hydrogels exhibiting a temperature‐dependent release were prepared by incorporating hydrophobically modified poly(N‐isopropylacrylamide) (HmPNIPAM) into β‐cyclodextrin hydrogels (β‐CD hydrogels). The specific loading of HmPNIPAM was about 0.0069 g HmPNIPAM/g β‐CD hydrogels. The incorporation of the polymer was qualitatively conformed by FT‐IR spectroscopy and SEM. The percent release of blue dextran in 24 hr at 20°C (about 77%) was markedly higher than those obtained at 35°C and 45°C (about 53 and 55%, respectively). At the higher temperatures, the volume of the hydrogel could decrease upon the thermal contraction of HmPNIPAM, leading to a smaller mesh and a suppressed release. In fact, the swelling ratio in 24 hr at 35°C and 45°C (about 396% and 405%, respectively) was obviously lower than that obtained at 20°C (about 465%). Copyright © 2011 John Wiley & Sons, Ltd.     

Novel poly(N‐isopropylacrylamide)/clay/poly(acrylamide) IPN hydrogels with the response rate and drug release controlled by clay content

Novel interpenetrating network (IPN) hydrogels (PNIPAAm/clay/PAAm hydrogels) based on poly(N‐isopropylacrylamide) (PNIPAAm) crosslinked by inorganic clay and poly(acrylamide) (PAAm) crosslinked by organic crosslinker were prepared in situ by ultraviolet (UV) irradiation polymerization. The effects of clay content on temperature dependence of equilibrium swelling ratio, deswelling behavior, thermal behavior, and the interior morphology of resultant IPN hydrogels were investigated with the help of Fourier transform infrared spectroscopy, differential scanning calorimeter (DSC), scanning electron microscope (SEM). Study on temperature dependence of equilibrium swelling ratio showed that all IPN hydrogels exhibited temperature‐sensitivity. DSC further revealed that the temperature‐sensitivity was weakened with increasing amount of clay. Study on deswelling behavior revealed that IPN hydrogels had much faster response rate when comparing with PNIPAAm/clay hydrogels, and the response rate of IPN hydrogels could be controlled by clay content. SEM revealed that there existed difference in the interior morphology of IPN hydrogels between 20 [below lower critical solution temperature (LCST)] and 50 °C (above LCST), and this difference would become obvious with a decrease in clay content. For the standpoint of applications, oscillating swelling/deswelling behavior was investigated to determine whether properties of IPN hydrogels would be stable for potential applications. Bovine serum albumin (BSA) was used as model drug for in vitro experiment, the release data suggested that the controlled drug release could be achieved by modulating clay content. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 96–106, 2009     

Dual temperature‐ and pH‐sensitive hydrogels from interpenetrating networks and copolymerization of N‐isopropylacrylamide and sodium acrylate

Hydrogels responsive to both temperature and pH have been synthesized in the forms of sequential interpenetrating networks (IPNs) of N‐isopropylacrylamide (NIPAAm) and sodium acrylate (SA) and compared with the crosslinked random copolymers of N‐isopropylacrylamide and SA. Whereas the stimuli‐sensitive behaviors of copolymer hydrogels were strongly dependent on the ionic SA contents, the IPN hydrogels exhibited independent swelling and thermal behaviors of each network component. The sequences and media in the synthesis of IPNs influenced the swelling capacities of the IPNs, but not the temperature or pH ranges at which the swelling changes occurred. In IPNs, a more expanded primary gel network during the synthesis of the secondary network contributed to the better swelling of the final IPNs. Both the swelling and thermal behaviors of the IPNs suggest that poly(N‐isopropylacrylamide) and poly(sodium acrylate) are phase separated regardless of their synthesis conditions. The presence of the poly(sodium acrylate) network did not influence the temperature or the extent of phase transition of the poly(N‐isopropylacrylamide) network in the IPNs, but did improve the thermal stability of the IPNs. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 3293–3301, 2004     

Novel Interpenetrating Networks (IPNs) Hydrogels Prepared In Situ by Liquid-Phase Photopolymerization

Novel interpenetrating networks (IPNs) hydrogels responsive to temperature were prepared in situ by liquid-phase photopolymerization. The first network of the IPNs (poly isopropyl acrylamide) were formed with a special kind of hectorite (Laponite XLS) modified by tetrasodium pyrophosphate as cross-linker and 2-oxogultaric acid as photoinitiator. The samples were subsequently immersed in an acrylamide (AAm) aqueous solution for at least one day for preparing IPNs hydrogels, in which acrylamide aqueous solution containing N,N′-Dimetyl acrylamide (MBAA) as cross-linker and 2-oxogultaric acid as photoinitiator. Then the second networks were in situ formed by introducing ultraviolet light irradiated PNIPAAm gels. The swelling/deswelling behaviors of IPNs hydrogels were measured. Compared with the corresponding nanocomposite PNIPAAm hydroges(NC hydrogels), chemically cross-linked PNIPAAm and PAAm IPNs hydrogels, the results indicate that the new IPN hydrogel has a faster deswelling rate above its LCST (≈32 °C). The effect was explained as being an additional contribution of the PAAm chains in IPN hydrogels, which may act as a water-releasing channel when the hydrophobic aggregation of PNIPA takes place.     

Synthesis and characterization of poly(N‐isopropylacrylamide) films by photopolymerization

A novel method used for the preparation of poly(N‐isopropylacrylamide) (PNIPAAm) films of varying crosslink density under homogeneous/heterogeneous conditions is described in this paper. Photopolymerization of the N‐isopropylacrylamide (NIPAAm) monomer in water (homogeneous at ～7°C and heterogeneous at ～40°C) or a mixture of water/ethanol (50:50, heterogeneous at ～7°C) was carried out using 1‐[4‐(2‐hydroxyethoxy)‐phenyl]‐2‐hydroxy‐2‐methyl‐1‐propane‐1‐one (hydrophilic) or 2‐hydroxy‐2‐methyl propiophenone (hydrophobic) photo‐initiator. In order to investigate the effect of temperature and crosslink density, polymerization was carried out at ～7°C [below lower critical soluble temperature (LCST)] and ～40°C (above LCST) using varying amounts of N,N′‐methylene bisacrylamide (BIS) ranging from 1–4 wt%. Degree of swelling (determined by optical microscopy), phase transition temperature [determined by differential scanning calorimetry (DSC)] as well as morphology (scanning electron microscopy) were found to be dependent on solvent system (homogeneous/heterogeneous), temperature of polymerization and crosslink density. Hydrogels prepared at ～7°C using hydrophobic photo‐initiator and water/ethanol (50:50) as solvent, showed much higher degree of swelling at all levels of crosslink density as compared to hydrogel prepared at ～7°C using hydrophilic photo‐initiator and water as solvent. Hydrogels were used for patterning which may find applications in microfluidic devices. Copyright © 2006 John Wiley & Sons, Ltd.     

Photoisomerizable and Thermoresponsive N‐isopropylacrylamide–Surfmer Copolymer Hydrogels Prepared upon Electrostatic Self‐Assembly of an Azobenzene Bolaamphiphile

Photoreactive and thermoresponsive N‐isopropylacrylamide (NIPAM)–surfmer copolymer hydrogels containing 4,4′‐di(6‐sulfato‐hexyloxy)azobenzene (DSHA) dianions are described. The functional hydrogels are obtained in a two steps. First a micellar aqueous solution of (11‐(acryloyloxy)undecyl)trimethylammonium bromide (AUTMAB) and NIPAM is exposed to ⁶⁰Co‐gamma irradiation, and a thermoresponsive copolymer gel is obtained. Second, DSHA is included by shrinking the gel at 50 °C and subsequent reswelling in an aqueous solution of DSHA disodium salt at 20 °C. Reswelling is accompanied by electrostatic adsorption of DSHA dianions at the positively charged AUTMAB headgroups replacing the bromide ions. Gels containing trans‐DSHA are transparent yellow at room temperature (λ_max = 370 nm), while gels containing cis‐rich DSHA are orange (λ_max = 460 and 330 nm). Energy dispersive X‐ray measurements indicate that 41% of the bromide ions are exchanged if trans‐DSHA is used for adsorption, and only 7.5% if cis‐DSHA is used. The incorporation of DSHA lowers the lower critical solution temperature (LCST) from 34 to 32 °C. Below the LCST, DSHA can be switched from the trans‐ to the cis‐rich state and vice versa upon irradiation with UV (λ = 366 nm) or visible light (λ ≥ 450 nm). Above the LCST no photoreaction takes place.     

Hydration‐mediated effects of saccharide stereochemistry on poly(N‐isopropylacrylamide) gel swelling

To shed new light on the mechanisms of saccharide stereochemistry effect on macromolecules in aqueous solutions, we studied the effect of three monosaccharide stereoisomers, glucose, galactose, and mannose, on the swelling of Poly(N‐isopropylacrylamide) (PNIPA) hydrogels. We equilibrated PNIPA hydrogels in sugar solutions of different concentrations at 25 °C, and determined gel volume and mass swelling ratios, and sugar concentration imbalance. The volume‐phase‐transition occurred at molal concentrations of 0.587 ± 0.004 (galactose), 0.724 ± 0.003 (glucose), and 0.846 ± 0.004 (mannose). The same order of sugars emerged for the gel‐swelling and the magnitude of the sugar concentration‐imbalance, which correlated with sugar isentropic molar compressibility and hydration number. The more hydrated the sugar, the worse a cosolvent it is for the polymer, hence the larger the deswelling and the more negative the sugar concentration imbalance. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

A novel sodium carboxymethylcellulose/poly(N‐isopropylacrylamide)/Clay semi‐IPN nanocomposite hydrogel with improved response rate and mechanical properties

A novel semi‐IPN nanocomposite hydrogel (CMC/PNIPA/Clay hydrogel) based on linear sodium carboxymethylcellulose (CMC) and poly(N‐isopropylacrylamide) (PNIPA) crosslinked by inorganic clay was prepared. The structure and morphology of these hydrogels were investigated and their swelling and deswelling kinetics were studied in detail. TEM images showed that the clay was substantially exfoliated to form nano‐dimension platelets dispersed homogeneously in the hydrogels and acted as a multifunctional crosslinker. The CMC/PNIPA/Clay hydrogels swell faster than the corresponding PNIPA/Clay hydrogels at pH 7.4, whereas they swell slower than the PNIPA/Clay hydrogels at pH 1.2. The CMC/PNIPA/Clay nanocomposite hydrogels showed much higher deswelling rates, which was ascribed to more passway formed in these hydrogels for water to diffuse in and out. The deswelling process of the hydrogels could be approximately described by the first‐order kinetic equation and the deswelling rate decreased with increasing clay content. The mechanical properties of the CMC/PNIPA/Clay nanocomposite hydrogels were analyzed based on the theory of rubber elasticity. It was found that with increasing clay content, the effective crosslink chain density, v_e, increased whereas the molecular weight of the chains between crosslinks M_c decreased. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1546–1555, 2008     

Dependence of Protein Recognition of Temperature‐Sensitive Imprinted Hydrogels on Preparation Temperature

Temperature‐sensitive imprinted and non‐imprinted hydrogels composed of N‐isopropylacrylamide (NIPA) and 2‐acrylamido‐2‐methyl‐propanosulfonic acid (AMPS) have been prepared by free‐radical crosslinking copolymerization in aqueous solution at three different temperatures: 10 °C (below the lower critical solution temperature, LCST), 33 °C (at the LCST), and 40 °C (above the LCST). Myoglobin (Mb, MW 17 kDa) is used as the template biomolecule. The effects of the initial concentration and adsorption time over the Mb adsorption capacity of the hydrogels have been analyzed and found to be strongly dependent on the preparation temperature (T_prep). The maximum Mb adsorption for the imprinted hydrogel prepared at 10 °C is 97.40 ± 2.35 mg Mb · g⁻¹ dry gel in 0.32 mg · mL⁻¹ Mb solution at 22 °C. Moreover, batch adsorption equilibrium and selectivity studies have been performed using a reference molecule, hemoglobin (Hb, MW 65 kDa). The imprinted hydrogels have a 2.8–3.3 times higher adsorption capacity for Mb than the non‐imprinted hydrogels prepared at the same T_preps, and also have a 1.8–2.7 times higher selectivity for the imprinted molecule.

     

Fast responsive poly(<Emphasis Type="Italic">N,N</Emphasis>-diethylacrylamide) hydrogels with interconnected microspheres and bi-continuous structures

We prepared thermo-responsive polymer hydrogels by γ-ray irradiation of aqueous solutions of N, N-diethylacrylamide at different temperatures below and above its lower critical solution temperature (LCST). Poly(N, N-diethylacrylamide) gel had a transparent and homogeneous structure when the radiation-induced polymerization and crosslinking were carried out below the LCST (25 °C) of the polymer. On the other hand, cloudy and heterogeneous gels were formed at temperatures above the LCST of the polymer (>35 °C). From environmental scanning electron microscopy observations, the gels prepared at 35 and 40 °C were seen to show sponge-like bi-continuous porous structures, while those prepared at 50 °C showed a porous structure consisting of interconnected microspheres. For temperature changes between 10 and 40 °C, gels with porous structures showed rapid volume transitions on a time scale of about a minute, not only for shrinking but also for swelling processes, which is in remarkable contrast to the porous poly(N-isopropylacrylamide) hydrogels.