Facile synthesis and characterization of the copolymers and their pure nanoparticles from aniline with 4‐sulfonic diphenylamine

Copolymer nanoparticles from aniline (AN) and 4‐sulfonic diphenylamine (SDP) were simply synthesized for the first time by an oxidative precipitation polymerization with inorganic oxidants in an acidic aqueous medium without any external emulsifier or stabilizer. The polymerization yield, intrinsic viscosity, solubility, solvatochromism, electrical conductivity, and thermal stability of the copolymers were systematically studied through changes in the AN/SDP ratio, polymerization temperature, oxidant species, monomer/oxidant ratio, and acidic medium. The molecular structure of the copolymers was characterized with elemental analysis, IR, and ultraviolet–visible spectra. The polymers exhibited very good solubility in polar solvents, water, and NH₄OH, and this was mainly attributable to the presence of sulfonic acid side groups. The electrical conductivity of the copolymers increased greatly, from 6.00 × 10^?4 to 2.55 × 10^?1 S/cm, with increasing AN content. The size of the copolymer particles, determined by laser particle analysis and atomic force microscopy (AFM), strongly depended on the polymer state and oxidant/monomer ratio. Pure dedoped particles of the AN/SDP (50/50) copolymer at an oxidant/monomer ratio of 1/2 exhibited minimum length/diameter ratios of 62/44 and 45/30 nm by AFM and transmission electron microscopy, respectively. The copolymers showed typical four‐step weight‐loss behavior in nitrogen and air and higher thermostability in nitrogen. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 3380–3394, 2004     

Synthesis and properties of processable conducting copolymers from N‐ethylaniline with aniline

Copolymers were synthesized through the chemically oxidative polymerization of N‐ethylaniline (EA) and aniline (AN) in five acid aqueous media. The polymerization yield, intrinsic viscosity, molecular weight, solubility, solvatochromism, electrical conductivity, and mechanical properties of the copolymer films were systematically studied through changes in the comonomer ratio, polymerization temperature, oxidant, oxidant/monomer ratio, and acid medium. Open‐circuit‐potential and temperature measurements of the polymerization solutions showed that the polymerization rate depended on the EA content, and the polymerization was an exothermic reaction. The resultant copolymers were characterized in detail with IR, ultraviolet–visible, and ¹H NMR spectroscopy, gel permeation chromatography, wide‐angle X‐ray diffractometry, and scanning electron microscopy. The reactivity ratios of the monomer pair were calculated from the ¹H NMR spectra of the copolymers formed at a low conversion. The polymers exhibited good solubility and interesting solvatochromism in most of the solvents and variable conductivity with the EA/AN ratio and doping state. The conductivity of the HCl‐doped copolymers increased monotonically from 5.61 × 10^?7 to 2.55 × 10^?1 S/cm with decreasing EA content from 100 to 0 mol % and showed a percolation transition between EA concentrations of 20 and 30 mol %. The EA/AN copolymers also had excellent film formability and flexibility together with high mechanical and oxygen‐enriching properties. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 6109–6124, 2004     

Synthesis of a soluble pyrrole copolymer with phenetidine

A new series of copolymers was synthesized through the oxidative polymerization of pyrrole (PY) and o‐phenetidine (PHT) with inorganic oxidants in acidic media. The polymerization parameters including the mixing method of the oxidant with the comonomer, the comonomer ratio, the time, the temperature, the oxidant, the organic medium, and the acid were systematically optimized for the synthesis of copolymers with high yields, intrinsic viscosities, and solubility. The resultant copolymers were characterized by elemental analysis, infrared, ultraviolet–visible, solution high‐resolution ¹H NMR and solid‐state high‐resolution ¹³C NMR, circular dichroism spectroscopy, and cyclic voltammetry. The results showed that the PY observed content in the copolymers was much higher than the PY feed content. The regular variation of the polymerization yield, intrinsic viscosity, solubility, macromolecular structure, and electroactivity of the resulting polymers with the comonomer ratio, together with the complete solubility of a PY/PHT (10/90) polymer in highly polar solvents, indicated the formation of real random copolymers containing both PY and PHT units rather than a mixture of two homopolymers. However, the polymers containing more than 59 mol % PY were not homogeneous copolymers consisting of soluble and insoluble parts. A semiquantitative relationship between the polymerization yield or solubility of the copolymers and the polarity index of the organic solvents was examined. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2073–2092, 2004     

Preparation and characterization of soluble terpolymers from m‐phenylenediamine,o‐anisidine,and 2,3‐xylidine

A series of terpolymers were synthesized by the chemical oxidative polymerization of m‐phenylenediamine (MPD), o‐anisidine (AS), and 2,3‐xylidine (XY) in hydrochloride aqueous medium. The yield, intrinsic viscosity, and solubility of the terpolymers were studied by changing the MPD/AS/XY molar ratio from 100/0/0 to 53/39/8 to 0/100/0. It was discovered that the MPD/AS/XY terpolymers exhibit a higher polymerization yield and better solubility than MPD/AS and MPD/XY bipolymers having the same MPD molar content. The as‐prepared MPD/AS/XY terpolymer bases were characterized by Fourier transform infrared, ultraviolet–visible, ¹H NMR, and high‐resolution solid‐state ¹³C NMR spectroscopies; wide‐angle X‐ray diffraction; and thermogravimetry. The results suggested that the oxidative polymerization from MPD, AS, and XY is exothermic, and the resulting terpolymers are more easily soluble in some organic solvents than MPD homopolymer. The copolymer obtained was a real terpolymer containing MPD, AS, and XY units, and the actual MPD/AS/XY molar ratio calculated by solid‐state ¹³C NMR spectra of the polymers is very close to the feed ratio, although the AS content calculated on the basis of the ¹H NMR spectrum of the soluble part of the polymer is higher than the feed AS content. The terpolymers and MPD homopolymer exhibit a higher polymerization yield and much higher intrinsic viscosity and are more amorphous than the AS homopolymer. At a fixed MPD content of 70 mol %, the terpolymers exhibit an increased thermostability and activation energy of the major degradation in nitrogen and air with an increasing AS content. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 3989–4000, 2001     

Configuration effects of ortho,meta, and para linkages on liquid crystallinity during thin‐film polymerization of poly(ester‐amide)s

By in situ thin‐film polymerization conducted on a heating stage of a polarizing microscope, we have investigated the effects of monomer structures on the formation of liquid crystallinity. Three polymerization systems studied are 2,6‐acetoxynaphthoic acid (ANA)/acetoxy acetanilide (AAA)/phthalic acid (PA), ANA/AAA/isophthalic acid (IA) and ANA/AAA/terephthalic acid (TA). In the three systems, PA, IA, and TA may create an ortho, a meta, and a para linkage, respectively. The formation of liquid crystallinity was found strongly dependent on the straightness and configuration of monomeric units. For ANA/AAA/PA and ANA/AAA/IA systems, there exists the critical ANA content to yield the liquid crystalline phase. Below this critical content, either amorphous phase forms or crystallization occurs during polymerization. Experimental data also indicate that defect density in the polymerization product reduces with increasing ANA content. Surprisingly, for the first time, we have observed that the ANA/AAA/PA system has a higher tendency to yield liquid crystallinity than the ANA/AAA/IA system. For the ANA/AAA/TA system, the polycondensation reaction is incomplete if the TA content is too high because of the low reactivity and the high melting point of TA. Polymerization of the ANA/AAA/TA system does not yield totally random copolymers because the liquid crystal phase appears before all TA crystals disappear during the polymerization. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 2221–2231, 2000     

Catalytic cyclopolymerization and copolymerization of 1,6‐heptadiynes by Mo(CO)6

The catalytic polymerization of a series of 1,6‐heptadiynes (1–4) by Mo(CO)₆ under simple thermal conditions produces corresponding poly(1,6‐heptadiyne)s with highly conjugated polyenes. The number‐average molecular weights of the polymers range from 2400 to 110,000. The structures of the polymers depend on the types of monomers employed. Namely, diethyl dipropargylmalonate (DEDPM) and 1 result in a polyene backbone consisting of only five‐membered rings, whereas the remaining monomers (2–4) result in a mixture of both five‐membered and six‐membered ring structures. The copolymerization of DEDPM and phenylacetylene (PA) can also be effected by the same catalysis to yield a polyene backbone consisting of only five‐membered rings as well as PA. The relative molar ratio of the two monomers determines the yields and molecular weights of the copolymers. Comparative studies show that Mo(CO)₆ exhibits reactivity toward DEDPM alone, thus initially catalyzing metathesis cyclopolymerization of DEDPM followed by copolymerization with PA. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 2663–2670, 2000     

Linear and comb‐like acrylonitrile/N‐isopropylacrylamide copolymers synthesized by the combination of RAFT polymerization and ATRP

We describe the synthesis of three novel thermoresponsive copolymers of acrylonitrile (AN) with N‐isopropylacrylamide (NIPAM) by a combination of reversible addition‐fragmentation chain transfer (RAFT) polymerization and atom transfer radical polymerization (ATRP). Linear copolymer polyacrylonitrile (PAN)‐b‐PNIPAM was directly prepared by RAFT polymerization. Comb‐like copolymers were synthesized by ATRP using brominated AN/2‐hydroxyethyl methacrylate copolymers as macroinitiators, which were prepared by RAFT polymerization. FT‐IR, NMR, and GPC were employed to characterize the synthesized copolymers. Results indicate that the polymerization processes can be well controlled and the resultant copolymers have well‐defined structures as well as narrow polydispersity. Then dense films were fabricated from these thermoresponsive copolymers and the surface wettability was evaluated by water contact angle measurements at different temperatures. It is found that the surface wettability is temperature‐dependant and both the transition temperature and decrement of water contact angle are affected by the copolymer shapes as well as the length of PNIPAM blocks. Considering the excellent fiber‐ and membrane‐forming properties of PAN‐based copolymers, the obtained thermoresponsive copolymers are latent materials for functional fibers and membranes. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 92–102, 2009     

Facile synthesis and optimization of conductive copolymer nanoparticles and nanocomposite films from aniline with sulfodiphenylamine

A new series of electrically conductive pure copolymer nanoparticles was facilely synthesized by using oxidative polymerization of aniline (AN) and sodium diphenylamine-4-sulfonate (SDP) in acidic media in the absence of stabilizer. The variation of the structure of the copolymer particles was comprehensively studied by carefully choosing several important parameters, such as the comonomer ratio, oxidant/monomer ratio, polymerization time and temperature, monomer concentration, acidic medium, and oxidant species. Analytical techniques used include IR and UV-visible spectroscopy, X-ray diffraction, laser particle analysis, atomic force microscopy, and transmission electron microscopy. It was found that the particle size varied significantly with the above-mentioned polymerization parameters, only changes in the salt concentration in the aqueous testing solution had no noticeable effect. The polymerization conditions were optimized for the formation of copolymer nanoparticles with sought-after properties. The doped copolymer particles of AN/SDP (50:50) at an oxidant/monomer molar ratio of 0.5 exhibit a minimum length of 50 nm and a minimum diameter of 44 nm. The bulk electrical conductivity of the copolymer particles increases greatly from 5.90x10(-4) to 1.15x10(-2) S cm(-1) with increasing AN content. Compared with barely soluble polyaniline, the copolymers exhibit a remarkably enhanced solubility in most solvents, including NH4OH and even water, due to the presence of the hydrophilic sulfonic groups. Nanocomposite films of the nanoparticles and cellulose diacetate exhibit a percolation threshold of down to 0.1 wt %, at which the film retains 98% of the transparency, 94% of the strength, and 5x10(7) times the conductivity of a pure cellulose diacetate film.     

Synthesis of poly(D,L‐lactic acid‐alt‐glycolic acid) from D,L‐3‐methylglycolide

D ,L ‐3‐Methylglycolide (MG) was synthesized via two step reactions with a good yield (42%). It was successfully polymerized in bulk with stannous octoate as a catalyst at 110 °C. The effects of the polymerization time and catalyst concentration on the molecular weight and monomer conversion were studied. Poly(D ,L ‐lactic acid‐co‐glycolic acid) (D ,L ‐PLGA50; 50/50 mol/mol) copolymers were successfully synthesized from the homopolymerization of MG with high polymerization rates and high monomer conversions under moderate polymerization conditions. ¹H NMR spectroscopy indicated that the bulk ring‐opening polymerization of MG conformed to the coordination–insertion mechanism. ¹³C NMR spectra of D ,L ‐PLGA50 copolymers obtained under different experimental conditions revealed that the copolymers had alternating structures of lactyl and glycolyl. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 4179–4184, 2000     

One‐pot synthesis of polyamide 12,T–polyamide‐6 block copolymers

Polyamide 12,T–polyamide‐6 (PA‐12,T–PA‐6) block copolymers were synthesized by anionic polymerization of caprolactam using a PA‐12,T macrocoinitiator (McI). PA‐12,T McI and its precursors are soluble in molten caprolactam allowing for both the McI step‐growth polymerization and anionic polymerization to be performed in one‐pot. It was found that the competing reaction rates of caprolactam ring‐opening polymerization and McI transamidation are both deterred by a common ion effect using CaCl₂ and soluble materials were obtained using >1 mol % CaCl₂. Without CaCl₂, the reaction mixture solidifies in less than 30 s and produces crosslinked materials. To understand this effect, PA‐12,T McI reactions with caprolactam were performed with 1–10 mol % CaCl₂, and polymer structures were characterized using ¹³C NMR and dilute solution viscometry. These data were then correlated with unique thermal properties and swelling behavior of the block copolymers. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Kinetics of chemical oxidative dispersion polymerization of 3,5‐xylidine in aqueous medium using a PH stat method

Kinetics of chemical oxidative dispersion polymerization of 3,5‐xylidine (Xy) in aqueous medium with ammonium persulfate (APS) as an oxidant was studied by monitoring the amount of proton released from Xy monomer, which was obtained from the amount of potassium hydroxide (KOH) solution added to keep constant pH values using a pH stat. The initial polymerization rate (R) [mol/L/min] of Xy was expressed as follows: R = 1.65 (1 − α) [Xy] [APS], where α is the degree of ionization of Xy, and [Xy] and [APS] are concentrations of Xy and APS, respectively. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 4238–4246, 2000     

1H NMR study of the kinetics of substituted aniline polymerization. II. Copolymerization of 2‐methoxyaniline and 3‐aminobenzenesulfonic acid

We investigated the kinetics of the oxidative chemical copolymerization of 2‐methoxyaniline (OMA) and 3‐aminobenzenesulfonic acid (MA) by monitoring monomer depletion with ¹H NMR spectroscopy. We adapted a semiempirical kinetic model, previously used for OMA homopolymerization, for the consumption of both OMA and MA monomers with a large difference in their reactivities. The OMA polymerization rate and end conversion showed a similar dependence on the reaction conditions, as described in the first part of this series, for its homopolymerization. Generally, the MA comonomer had an inhibition effect on the OMA polymerization rate. However, an increase in the initial MA concentration resulted in an increased OMA initiation rate. Because of the higher reactivity of OMA compared with that of MA, the OMA conversion began before the MA conversion, and both the initiation and propagation rates were higher than those for MA. The molar ratios of the converted monomers (MA/OMA) were always significantly lower than the corresponding MA/OMA feed fractions. They depended on the reaction conditions used for the copolymerization. In particular, higher oxidant or MA concentrations, higher temperatures, and a 1 M DCl concentration favored MA conversion, that is, its insertion into the copolymer. The MA end conversion was much smaller than that of OMA, only up to 23%; for a low oxidant concentration (oxidant/monomer‐deficient molar ratio), it was only 6%. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 2482–2493, 2001     

Synthesis of novel polybenzimidazoles with pendant amino groups and the formation of their crosslinked membranes for medium temperature fuel cell applications

A series of new polybenzimidazoles (PBIs) with pendant amino groups have been synthesized via condensation polymerization of 5‐aminoisophthalic acid (APTA), isophthalic acid (iPTA), and 3,3′diaminobenzidine (DAB) in polyphosphoric acid at 190 °C for 20 h. The molar ratios between APTA and iPTA were controlled at 1:0, 2:1, 1:1, and 1:2, respectively, and the copolymerization reactions were carried out via both random and sequenced manners. The resulting polymers showed good solubility in some organic solvents such as dimethylsulfoxide (DMSO) and N,N‐dimethylacetamide (DMAc). The pendant amino groups of the PBIs were utilized to react with two kinds of crosslinkers, 1,3‐dibromopropane and ethylene glycol diglycidyl ether, to yield various crosslinked membranes. The crosslinked membranes generally showed good mechanical properties even at high‐phosphoric acid (PA) doping levels, whereas the uncrosslinked membranes highly swelled or even dissolved in PA. Fenton's test revealed that the crosslinked PBI membranes had excellent radical oxidative stability. The proton conductivities of the PA‐doped crosslinked membranes increased with an increase in temperature and high‐proton conductivity up to 0.14 S/cm at 0% relative humidity at 170 °C was achieved. The membranes with high PA‐doping levels, good mechanical properties, and high‐proton conductivities have been successfully developed. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2009     

Optimized water‐based ATRP of an anionic monomer: Comprehension and properties characterization

The effect of pH and the ligand nature over the atom transfer radical polymerization (ATRP) of the anionic monomer sodium 2‐acrylamido‐2‐methylpropanesulfonate (AMPSNa) was investigated in aqueous medium by using ω‐halogenated poly(ethylene oxide) and CuBr, as macroinitiator and catalyst, respectively. The stability of both catalytic complexes and macroinitiator was investigated in function of pH, that is, fixed between 7.5 and 12. UV‐VIS spectroscopy confirmed a good catalytic complex stability in the studied conditions. Hydrolysis of the macroinitiator ester group at pH higher than 7.5 was detected by ¹H NMR and GPC, yielding ill‐defined polymer samples when ATRP is performed in alkaline conditions. 2,2′‐Bipyridyl (Bpy), 1,1,4,7,10,10‐hexamethyltriethylenetetramine (HMTETA), and tris(2‐methylaminoethyl)amine (Me₆‐TREN)‐based complexes were compared at the optimal pH (pH 7.5). When polymerization was carried out in the presence of CuBr · 2Me₆‐TREN complex block copolymers with narrow molecular weight distribution (1.1 ≤ M _W/M _n ≤ 1.3), and good agreement between theoretical and experimental molar masses was obtained. Moreover, increasing the PAMPSNa polymerization degrees (n) did not affect the control over the polymerization. Preliminary characterization of the diblock copolymers behavior in aqueous medium revealed a strong polyelectrolyte effect independently of n. Interestingly, occurrence of interactions between the PEO and PAMPSNa‐blocks was also evidenced by differential scanning calorimetry and thermogravimetric analyses. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 1108–1119, 2009     

Atom transfer radical copolymerization of acrylonitrile and ethyl methacrylate at ambient temperature

Copolymerization of acrylonitrile (AN) and ethyl methacrylate (EMA) using copper‐based atom transfer radical polymerization (ATRP) at ambient temperature (30 °C) using various initiators has been investigated with the aim of achieving control over molecular weight distribution. The effect of variation of concentration of the initiator, ligand, catalyst, and temperature on the molecular weight distribution and kinetics were investigated. No polymerization at ambient temperature was observed with N,N,N′,N′,N″‐pentamethyldiethylenetriamine (PMDETA) ligand. The rate of polymerization exhibited 0.86 order dependence with respect to 2‐bromopropionitrile (BPN) initiator. The first‐order kinetics was observed using BPN as initiator, while curvature in first‐order kinetic plot was obtained for ethyl 2‐bromoisobutyrate (EBiB) and methyl 2‐bromopropionate (MBP), indicating that termination was taking place. Successful polymerization was also achieved with catalyst concentrations of 25 and 10% relative to initiator without loss of control over polymerization. The optimum [bpy]₀/[CuBr]₀ molar ratio for the copolymerization of AN and EMA through ATRP was found to be 3/1. For three different in‐feed ratios, the variation of copolymer composition (F_AN) with conversion indicated toward the synthesis of copolymers having slight changes in composition with conversion. The high chain‐end functionality of the synthesized AN‐EMA copolymers was verified by further chain extension with methyl acrylate and styrene. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 1975–1984, 2006     

A minimal amount of acrylonitrile turns the nitroxide‐mediated polymerization of methyl methacrylate into an almost ideal controlled/living system

Nitroxide‐mediated controlled/living free‐radical polymerization of methyl methacrylate initiated by the SG1‐based alkoxyamine BlocBuilder was successfully performed in bulk at 80–99 °C with the help of a very small amount of acrylonitrile (AN, 2.2–8.8 mol %) as a comonomer. Well‐defined PMMA‐rich P(MMA‐co‐AN) copolymers were prepared with the number‐average molar mass, M_n, in the 6.1–32 kg mol^?1 range and polydispersity indexes as low as 1.24. Incorporation of AN in the copolymers was demonstrated by ¹H and ¹³C NMR spectroscopy, and its effect on the chain thermal properties was evaluated by DSC and TGA analyses. Investigation of chain‐end functionalization by an alkoxyamine group was performed by means of ³¹P NMR spectroscopy and chain extensions from a P(MMA‐co‐AN)‐SG1 macroinitiator. It demonstrated the very high proportion of SG1‐terminated polymer chains, which opened the door to block copolymer synthesis with a high quality of control. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 34–47, 2010     

Facile synthesis and intrinsic conductivity of novel pyrrole copolymer nanoparticles with inherent self-stability

Intrinsically self-stabilized nanoparticles of a copolymer from 4-sulfonic diphenylamine (SD) and pyrrole (PY) were facilely synthesized in HCl solution at 10 degrees C by a chemically oxidative polymerization. The critical reaction parameters such as SD/PY ratio, polymerization time, and oxidant species were studied to significantly optimize the polymerization yield, size, conductivity, and solubility of the final copolymer particles. The molecular structure, size, size distribution, and morphology of the particles were analyzed by IR spectroscopy, laser particle-size analysis (LPA), atomic force microscopy, and transmission electron microscopy (TEM). It was found that the polymerization yield of the SD/PY (50/50) copolymers increased dramatically in the initial 2 h of polymerization and then slowly enlarged in the subsequent 22 h. However, the copolymerization yield for the polymerization time of 24 h exhibited a nonlinear dependence on the SD/PY molar ratio, i.e., a maximum at 10/90 and a minimum at 80/20. The number-average diameter, Dn, of the copolymer particles strongly depended on the SD/PY ratio, decreasing rapidly from 6402 to 291 nm as the SD/PY molar ratio changed from 30/70 to 50/50, whereas the polydispersity index, PDI = Dw/Dn (where Dw is the weight-average diameter), surprisingly maintained very small values, decreasing slightly from 1.21 to 1.08. The SD/PY (80/20) copolymer particles prepared with (NH4)2S2O8 as the oxidant had the smallest size of ca. 10 nm by TEM and the lowest Dw/Dn value of 1.03 by LPA, whereas the copolymer particles prepared with FeCl3 as the oxidant exhibited the second smallest size of ca. 20 nm by TEM and the highest conductivity. The conductivity of the SD/PY (50/50) copolymers rose first and then decreased with increasing polymerization time from 10 min to 24 h, exhibiting a maximum (0.217 S/cm) at 12 h. It is of interest that the copolymer particles with SD/PY molar ratios in the range between 50/50 and 80/20 surprisingly exhibited the smallest size, the narrowest size distribution, and the highest conductivity at the same time. In particular, the copolymer nanoparticles exhibited high purity, clean surfaces, good self-stability, high conductivity, and strong chemoresistance that were very important to nanomaterial processibility and application. The obtained copolymers were partially soluble in concentrated H2SO4, demonstrating a new direction for synthesizing a soluble pyrrole copolymer.     

One‐shot synthesis of high molar mass polyurethane in supercritical carbon dioxide

Well‐defined polyurethane–polydimethylsiloxane particles of tunable diameter in the range of 0.5–20 μm were synthesized in “one‐shot” by step‐growth polymerization using supercritical carbon dioxide (scCO₂) as a dispersant medium. Polymerizations were carried out at 60 °C and above 25 MPa, after the solubility of each reactant in scCO₂ has been determined in its typical reaction concentration. The synthesis of such copolymers was achieved by polyaddition between short aliphatic diols, that is, ethylene glycol, 1,4‐butanediol (BD) or polyethylene oxide (M_n = 200 g mol^?1), and tolylene‐1,4‐di‐isocyanate (TDI) in the presence of mono or di‐isocyanate‐terminated polydimethylsiloxane (PDMS) as reactive stabilizers and dibutyltin dilaurate as a catalyst. The nature of the diol used as well as the functionality of the reactive stabilizer incorporated was found to have a dramatic effect on the molar mass and the morphology of the resulting product. Thus, copolymers obtained from the polyaddition of BD and TDI in the presence of di‐isocyanate‐terminated PDMS exhibit molar mass up to 90,000 g mol^?1. Thermal behaviors of copolymers were also examined by differential scanning calorimetry. All samples exhibited only one glass transition temperature (T_g) and were found to be totally amorphous. A logical decrease of the T_g was observed as the length of the diol incorporated increased, that is, as the density of urethane linkages within the polymer decreased. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5649–5661, 2007     

Optimization of polymerization conditions of furan with aniline for variable conducting polymers

A high-throughput multiparameter optimization of chemical oxidative polymerization conditions has been developed for a facile synthesis of furan homopolymers and furan/aniline copolymers using a combinatorial method. The polymerization yield, molecular structure, and properties of the polymers would be optimized against typical polymerization parameters, including oxidant species, medium species, temperature, oxidant/monomer ratio, monomer concentration, dopant concentration, and furan/aniline comonomer ratio. The electrical conductivity, lead ion adsorptivity, chemical resistance, and thermal behavior of the polymers were also elaborated. It is found that only a combination of FeCl(3) and nitromethane as oxidant and medium, respectively, is appropriate for the furan homopolymerization. The homopolymerization yield increases consistently with an increase in the monomer concentration from 0.05 to 0.2 M and the FeCl(3)/furan molar ratio from 0.25 to 1.25. Although the as-prepared polyfuran exhibits very low conductivity, down to 10(-11) S cm(-1), the HCl- and HClO(4)-doped polyfurans possess much higher conductivities of 9.2 x 10(-8) and 2.38 x 10(-5) S cm(-1), respectively. In addition, the conductivity of the furan/aniline copolymer rises steadily with increasing aniline content, although the copolymerization yield shows a minimum at the furan/aniline molar ratio of 60/40, which is evidence of the occurrence of a real copolymerization between the furan and aniline monomers. The difficulty of synthesizing conducting polyfuran could be overcome to some extent by the polymerization in an appropriate condition optimized in this study. Particularly, the difficulty of synthesizing poly(furan-co-aniline) having much higher conductivity than the polyfuran would be largely conquered by chemical oxidative copolymerization of furan with aniline.     

Copper(0)‐mediated living radical polymerization of acrylonitrile at room temperature

The copper(0)‐catalyzed living radical polymerization of acrylonitrile (AN) was investigated using ethyl 2‐bromoisobutyrate as an initiator and 2,2′‐bipyridine as a ligand. The polymerization proceeded smoothly in dimethyl sulphoxide with higher than 90% conversion in 13 h at 25 °C. The polymerization kept the features of controlled radical polymerization. ¹H NMR spectra proved that the resultant polymer was end‐capped by ethyl 2‐bromoisobutyrate species. Such polymerization technique was also successfully introduced to conduct the copolymerization of styrene (St) and AN to obtain well‐controlled copolymers of St and AN at 25 °C, in which the monomer conversion of St could reach to higher than 90%. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011