MALDI‐TOF‐MS analysis of living cationic polymerization of vinyl ethers. II. Living nature of growing end and side reactions

Matrix‐assisted laser desorption/ionization time‐of‐flight mass spectrometry analysis revealed that the HCl–vinyl ether adduct/SnCl₄/n‐Bu₄NCl initiating system induced living cationic polymerization of isobutyl vinyl ether in CH₂Cl₂ at ?78 °C, that is, the well‐resolved spectra demonstrated that the produced polymers consist of only one series of polymers carrying one initiator fragment at the α end and one methoxy group originated from quenching with methanol at the ω end. The polymer molecular weight as well as the terminal structure were unchanged even when the reaction mixtures were kept unquenched at ?78 °C for an interval of more than five times longer than the reaction period after complete consumption of monomer, which indicates the long lifetime of the living end even under such starved conditions. In contrast, the polymers obtained at a higher temperature, ?15 °C, showed an additional minor series of polymers formed via proton initiation, originating from adventitious water. Under the starved conditions, other side reactions occurred to generate minor series of polymers with an aldehyde ω end or a diisobutyl acetal ω end. Rather surprisingly, however, unsaturated C?C end groups were not detected, which means the absence of β‐proton elimination under these conditions. © 2001 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 1249–1257, 2001     

MALDI‐TOF‐MS analysis of living cationic polymerization of vinyl ethers. III. Polymerization with SnCl4 and TiCl4 in the absence of additives

Matrix‐assisted laser desorption/ionization time‐of‐flight mass spectrometry analysis revealed that the precision control (or the living nature) of the cationic polymerization of vinyl ethers with SnCl₄ or TiCl₄ critically depends on the Lewis acid concentration and temperature. Specifically, at an extremely low Lewis acid concentration, for example, the polymerization with the HCl–vinyl ether adduct (an initiator) is living at ?78 °C in CH₂Cl₂ solvent, whereas side reactions occurred at a higher concentration of SnCl₄ or at a higher temperature, ?15 °C. This was more pronounced with SnCl₄ than with TiCl₄, which was due to a stronger Lewis acidity of SnCl₄ as suggested by NMR analysis of the model reactions. © 2001 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 1258–1267, 2001     

Rapid living cationic polymerization of vinyl ethers by a single‐molecular initiating system

Initiated by an organic molecule trifluoromethanesulfonimide (HNTf₂) without any Lewis acid or Lewis base stabilizer, cationic polymerization of isobutyl vinyl ether (IBVE) takes place rapidly and the polymerization is proved to be in a controlled/living manner. The conversion of IBVE could easily achieve 99% in seconds. The product poly(isobutyl vinyl ether) is narrowly distributed and its molecular weight increases linearly with time and fits well with the corresponding theoretical value. This single‐molecular initiating system also works well in the living cationic polymerization of ethyl vinyl ether. HNTf₂ is considered playing multiple roles which include initiator, activator, and stabilizer in the polymerization. It is quite different from the hydrogen halide‐catalyzed polymerizations of vinyl ethers. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 1373‐1377     

Matrix‐assisted laser desorption/ionization time‐of‐flight mass spectroscopic analysis of telechelic polythiourethanes obtained by the cationic ring‐opening polymerization of six‐membered cyclic thiourethane

A matrix‐assisted laser desorption/ionization time‐of‐flight (MALDI‐TOF) mass spectroscopy analysis of polythiourethanes obtained by the cationic ring‐opening polymerization of a six‐membered cyclic thiourethane [3‐benzyltetrahydro‐1,3‐oxazine‐2‐thione (BTOT)] is described. A MALDI‐TOF mass spectrum of a polymer obtained by the polymerization of BTOT with boron trifluoride etherate (BF₃OEt₂) as the initiator in nitrobenzene at 50 °C for 24 h followed by an end‐capping reaction with diethyldithiocarbamic acid diethylammonium salt showed a series of well‐resolved signals that were assignable to polythiourethanes possessing an amino group at the initiating end and a diethyldithiocarbamate group at the terminating end. In comparison with the MALDI‐TOF mass spectra of polymers obtained by polymerization with trifluoromethanesulfonic acid or methyl trifluoromethanesulfonate, the plausible initiating species in the polymerization with BF₃OEt₂ was estimated to be a proton, which successively eliminated carbonyl sulfide to produce a secondary amine group at the initiating end. The secondary amine group in the obtained telechelic polymer was converted to a tertiary amine group by a reaction with benzyl bromide in the presence of triethylamine, and this was confirmed by MALDI‐TOF mass spectroscopy. Furthermore, a telechelic polymer with a pyrrole end group was successfully synthesized by the end‐capping reaction of the growing species in the polymerization of BTOT with sodium 1‐pyrrolecarbodithioate. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 4281–4289, 2006     

Living cationic polymerization of 2‐adamantyl vinyl ether

Living cationic polymerization of 2‐adamantyl vinyl ether (2‐vinyloxytricyclo[3.3.1.1]^3,7decane; 2‐AdVE) was achieved with the CH₃CH(OiBu)OCOCH₃/ethylaluminum sesquichloride/ethyl acetate [CH₃CH(OiBu)OCOCH₃/Et_1.5AlCl_1.5/CH₃COOEt] initiating system in toluene at 0 °C. The number‐average molecular weights (M_n's) of the obtained poly(2‐AdVE)s increased in direct proportion to monomer conversion and produced the polymers with narrow molecular weight distributions (MWDs) (M_w/M_n = ～1.1). When a second monomer feed was added to the almost polymerized reaction mixture, the added monomer was completely consumed and the M_n's of the polymers showed a direct increase against conversion of the added monomer. Block and statistical copolymerization of 2‐AdVE with n‐butyl vinyl ether (CH₂?CH? O? CH₂ CH₂CH₂CH₃; NBVE) were possible via living process based on the same initiating system to give the corresponding copolymers with narrow MWDs. Grass transition temperature (T_g) and thermal decomposition temperature (T_d) of the poly(2‐AdVE) (e.g., M_n = 22,000, M_w/M_n = 1.17) were 178 and 323 °C, respectively. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 1629–1637, 2008     

Precise synthesis of end‐functionalized thermosensitive poly(vinyl ether)s by living cationic polymerization

A series of poly(2‐methoxyethyl vinyl ether)s with narrow molecular weight distributions and with perfectly defined end groups of varying hydrophobicities was successfully synthesized by base‐assisting living cationic polymerization. The end group was shown to greatly affect the temperature‐induced phase separation behavior of aqueous solutions (lower critical solution temperature‐type phase separation) or organic solutions (upper critical solution temperature‐type phase separation) of the polymers. The cloud points were also influenced largely by the molecular weight and concentration of the polymer. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Living cationic polymerization of vinyl ethers by electrophile/lewis acid initiating systems. VII. Living cationic polymerization of isobutyl vinyl ether by trimethylsilyl halide/zinc halide initiating systems in the presence of p-methoxybenzaldehyde: Effects of halide anions and zinc halides

Trimethylsilyl halides (Me₃SiY), in conjunction with zinc halides (ZnX₂) (Y and X:I, Br, Cl), were employed to investigate the living cationic polymerization of isobutyl vinyl ether (IBVE) in toluene at ?15°C in the presence of p-methoxybenzaldehyde; with the aldehyde and IBVE monomer, Me₃SiY yields an initiating species [Me₃Si? O? CHC₆H₄(OM_e) ? CH₂CH(OiBu) ? Y] that triggers the IBVE polymerization via the activation of its carbon-halogen bond (C? Y) by ZnX₂ into C^δ+…?Y^δ?…?ZnX₂. Living polymerizations occurred with the silyl iodide and bromide irrespective of the type of ZnX₂, either when Y = X (Me₃Sil/Znl₂ and Me₃SiBr/ZnBr₂) or when Y ≠ X (Me₃Sil/ZnBr₂, Me₃SiI/ZnCl₂, and Me₃SiBr/Znl₂). With these five initiating systems, the number-average molecular weights (M?_n) of the polymers increased in proportion to monomer conversion, and the molecular weight distributions (MWDs) of the polymers were narrow (M?_w/M?_n = 1.1?1.2). The Me₃SiCl-based systems (Me₃SiCl/ZnCl₂ and Me₃SiCl/Znl₂), in (Me₃SiCl/Znl₂), in contrast, failed to give perfectly living polymerization; the M?_n indeed increased with conversion, but the MWDs of the polymers were broader (M?_w/M?_n = 1.3?1.5). Thus, the living nature of the polymerizations with Me₃SiY/Znx₂ is primarily determined by the halogen Y in Me₃SiY, which generates the terminal carbon-halogen bond (C? Y) that is activated by ZnX₂ for the propagation via a species C^δ+…?Y^δ?…?ZnX₂. For Y^?, not only the iodide but the bromide anion also is suited for living cationic polymerization. The virtual absence of the effects of X in ZnX₂ implies that the halogen exchange between ZnX₂ and Y from Me₃ SiY at the growing end (C^λ+…?Y^δ?…?ZnX₂ ?C^δ+…?X^δ?…?ZnXY) is absent or negligible.     

Living cationic polymerization of isobutyl vinyl ether by EtAlCl2 in the presence of ether additives: Cyclic ethers,cyclic formals,and acyclic ethers with oxyethylene units

The living cationic polymerization of isobutyl vinyl ether (IBVE) was investigated in the presence of various cyclic and acyclic ethers with 1-(isobutoxy)ethyl acetate [CH₃CH(OiBu)OCOCH₃, 1 ]/EtAlCl₂ initiating system in hexane at 0°C. In particular, the effect of the basicity and steric hindrance of the ethers on the living nature and the polymerization rate was studied. The polymerization in the presence of a wide variety of cyclic ethers [tetrahydrofuran (THF), tetrahydropyran (THP), oxepane, 1,4-dioxane] and cyclic formals (1,3-dioxolane, 1,3-dioxane) gave living polymers with a very narrow molecular weight distribution (MWD) (M?_ω/M?_n ≤ 1.1). On the other hand, propylene oxide and oxetane additives resulted in no polymerization, whereas 1,3,5-trioxane gave the nonliving polymer with a broader MWD. The polymerization rates were dependent on the number of oxygen and ring sizes, which were related to the basicity and the steric hindrance. The order of the apparent polymerization rates in the presence of cyclic ether and formal additives was as follows: nonadditive ～ 1,3,5-trioxane ? 1,3-dioxane > 1,3-dioxolane ? 1,4-dioxane ? THP > oxepane ? THF ? oxetane, propylene oxide ? 0. The polymerization in the presence of the cyclic formals was much faster than that of the cyclic ethers: for example, the apparent propagation rate constant k in the presence of 1,3-dioxolane was 10³ times larger than that in the presence of THF. Another series of experiments showed that acyclic ethers with oxyethylene units were effective as additives for the living polymerization with 1 /EtAlCl₂ initiating system in hexane at 0°C. The polymers obtained in the presence of ethylene glycol diethyl ether and diethylene glycol diethyle ether had very narrow molecular weight distribution (M?_ω/M?_n ≤ 1.1), and the M?_n was directly proportional to the monomer conversion. The polymerization behavior was quite different in the polymerization rates and the MWD of the obtained polymers from that in the presence of diethyl ether. These results suggested the polydentate-type interaction or the alternate interaction of two or three ether oxygens in oxyethylene units with the propagating carbocation, to permit the living polymerization of IBVE. © 1994 John Wiley & Sons, Inc.     

Living cationic polymerization of vinyl ethers by electrophile/lewis acid initiating systems. XII. Phosphoric and phosphinic acids/zinc chloride initiating systems for isobutyl vinyl ether

Phosphoric and phosphinic acid derivatives (R¹R²PO₂H; R¹, R² = OPh, OPh; OnBu, OnBu; Ph, Ph; Ph, H) in conjunction with zinc chloride (ZnCl₂) led to living cationic polymerization of isobutyl vinyl ether (IBVE) in toluene below 0°C. The number-average molecular weights (M?_n) of the polymers (M?_n > 2 × 10⁴) were directly proportional to monomer conversion and in excellent agreement with the calculated values assuming that one polymer chain forms per R¹R²PO₂H molecule. Throughout the reaction, the molecular weight distributions (MWDs) stayed narrow (M?_w/M?_n ? 1.1). A dibasic acid, PhOP (O) (OH)₂, coupled with ZnCl₂, also induced living cationic polymerization of IBVE where one molecule of the acid generated two living polymer chains. The polymerization by (PhO)₂PO₂H/ZnCl₂ and its model reactions were directly analyzed by ³¹P and ¹H-NMR spectroscopy. The analysis showed that the acid initially forms the adduct [CH₃CH(OiBu)OP(O)(OPh)₂], the phosphate linkage of which is in turn activated by ZnCl₂ so as to initiate living propagation. The finding thus indicates that (PhO)₂PO₂H indeed acts as an initiator in the living polymerization. The NMR analysis also suggested that an exchange reaction occurs between the phosphate group at the polymer terminal and the chlorine in ZnCl₂. The occurrence of living IBVE polymerization with these various R¹R²PO₂H/ZnCl₂ systems shows that phosphoric and phosphinic acids are another general class of protonic acids which are effective initiators for the living cationic polymerization assisted by Lewis acids. © 1993 John Wiley & Sons, Inc.     

Living cationic polymerization of an azide‐containing vinyl ether toward addressable functionalization of polymers

We first achieved the living cationic polymerization of azide‐containing monomer, 2‐azidoethyl vinyl ether (AzVE), with SnCl₄ as a catalyst (activator) in conjunction with the HCl adduct of a vinyl ether [H‐CH₂CH(OR)‐Cl; R ? CH₂CH₂Cl, CH₂CH(CH₃)₂]. Despite the potentially poisoning azide group, the produced polymers possessed controlled molecular weights and fairly narrow distributions (M_w/M_n ～ 1.2) and gave block polymers with 2‐chloroethyl vinyl ether. The pendent azide groups are easily converted into various functional groups via mild and selective reactions, such as the Staudinger reduction and copper‐catalyzed azide‐alkyne 1,3‐cycloaddition (CuAAC; a “click” reaction). These reactions led to quantitative pendent functionalization into primary amine (? NH₂), hydroxy (? OH), and carboxyl (? COOH) groups, at room temperature and without any acidic or basic treatment. Thus, poly(AzVE) is a versatile precursor for a wide variety of functional vinyl ether polymers with well‐defined structures and molecular weights. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 1449–1455, 2010     

Living carbocationic polymerization of isobutyl vinyl ether and the synthesis of poly[isobutylene-b-(isobutyl vinyl ether)]

The MeCH(O-i-Bu)Cl/TiCl₄/MeCONMe₂ initiating system was found to induce the rapid living carbocationic polymerization (LC^⊕Pzn) of isobutyl vinyl ether (IBuVE) at ?100°C. Degradation by dealcoholation which usually accompanies the polymerization of alkyl vinyl ethers by strong Lewis acids is “frozen out” at this low temperature and poly(isobutyl vinyl ether)s (PIBuVEs) with theoretical molecular weights up to ca. 40,000 g/mol (calculated from the initiator/monomer input) and narrow molecular weight distributions (M?_w/M?_n ≤ 1.2) are readily obtained. According to ¹³C-NMR spectroscopy, PIBuVEs prepared by living polymerization at ?100°C are not stereoregular. The MeCH(O-i-Bu)Cl/TiCl₄ combination induces the rapid LC^⊕Pzn of IBuVE even in the absence of N,N-dimethylacetamide (DMA). The addition of the common ion salt, n-Bu₄NCl to the latter system retards the polymerization and meaningful kinetic information can be obtained. The kinetic findings have been explained in terms of TiCl₄. IBuVE and TiCl₄ · IBuVE and TiCl₄ · PIBuVE complexes. The HCl (formal initiator)/TiCl₄/DMA combination is the first initiating system that can be regarded to induce the LC^⊕Pzn of both isobutylene (IB) and IBuVE. Polyisobutylene (PIB)–PIBuVE diblocks were prepared by sequential monomer addition in “one pot” by the 2-chloro-2,4,4-trimethylpentane (TMP-Cl)/TiCl₄/DMA initiating system. Crossover efficiencies are, however, below 35% because the PIB^⊕ + IBuVE → PIB-b-PIBuVE^⊕ crossover is slow. © 1993 John Wiley & Sons, Inc.     

Cationic polymerization of isobutyl vinyl ether initiated with transition‐metal ate complexes

The cationic polymerization of isobutyl vinyl ether was examined with transition‐metal ate complexes with trityl cation as initiators. The initiators were generated by the reaction of triphenylmethyl chloride [trityl chloride (TrCl)] with ate complexes of Nb, Mo, and W with lithium cation, which were obtained in situ by the reaction of the transition‐metal halides with anionic reagents (organolithium or lithium amide). When the polymerization was initiated with a mixture of TrCl and Li⁺[NbH₅(NnBuPh)]^?, the resulting poly(isobutyl vinyl ether)s had narrow molecular weight distributions (weight‐average molecular weight/number‐average molecular weight = 1.13–1.20). Although the polymerization was supposed to be initiated by the electrophilic attack of the trityl cation, matrix‐assisted laser desorption/ionization time‐of‐flight mass spectrometry analysis of the resulting poly(isobutyl vinyl ether)s revealed the presence of H at the α‐chain end. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2636–2641, 2006     

Living cationic polymerization of vinyl ethers with a urethane group

To study the possibility of living cationic polymerization of vinyl ethers with a urethane group, 4‐vinyloxybutyl n‐butylcarbamate ( 1 ) and 4‐vinyloxybutyl phenylcarbamate ( 2 ) were polymerized with the hydrogen chloride/zinc chloride initiating system in methylene chloride solvent at ?30 °C ([monomer]₀ = 0.30 M, [HCl]₀/[ZnCl₂]₀ = 5.0/2.0 mM). The polymerization of 1 was very slow and gave only low‐molecular‐weight polymers with a number‐average molecular weight (M_n) of about 2000 even at 100% monomer conversion. The structural analysis of the products showed occurrence of chain‐transfer reactions because of the urethane group of monomer 1 . In contrast, the polymerization of vinyl ether 2 proceeded much faster than 1 and led to high‐molecular‐weight polymers with narrow molecular weight distributions (MWDs ≤ ～1.2) in quantitative yield. The M_n's of the product polymers increased in direct proportion to monomer conversion and continued to increase linearly after sequential addition of a fresh monomer feed to the almost completely polymerized reaction mixture, whereas the MWDs of the polymers remained narrow. These results indicated the formation of living polymer from vinyl ether 2 . The difference of living nature between monomers 1 and 2 was attributable to the difference of the electron‐withdrawing power of the carbamate substituents, namely, n‐butyl for 1 versus phenyl for 2 , of the monomers. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2960–2972, 2004     

Synthesis of end‐functionalized polymers and copolymers of cyclopentadiene with vinyl ethers by cationic polymerization

A series of cyclopentadiene (CPD)‐based polymers and copolymers were synthesized by a controlled cationic polymerization of CPD. End‐functionalized poly(CPD) was synthesized with the HCl adducts [initiator = CH₃CH(OCH₂CH₂X)Cl; X = Cl ( 2a ), acetate ( 2b ), or methacrylate] of vinyl ethers carrying pendant functional substituents X in conjunction with SnCl₄ (Lewis acid as a catalyst) and n‐Bu₄NCl (as an additive) in dichloromethane at −78 °C. The system led to the controlled cationic polymerizations of CPD to give controlled α‐end‐functionalized poly(CPD)s with almost quantitative attachment of the functional groups (F_n ∼ 1). With the 2a or 2b /SnCl₄/n‐Bu₄NCl initiating systems, diblock copolymers of 2‐chloroethyl vinyl ether (CEVE) and 2‐acetoxyethyl vinyl ether with CPD were also synthesized by the sequential polymerization of CPD and these vinyl ethers. An ABA‐type triblock copolymer of CPD (A) and CEVE (B) was also prepared with a bifunctional initiator. The copolymerization of CPD and CEVE with 2a /SnCl₄/n‐Bu₄NCl afforded random copolymers with controlled molecular weights and narrow molecular weight distributions (weight‐average molecular weight/number‐average molecular weight = 1.3–1.4). © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 398–407, 2001