Chromatographic characterization of amphiphilic di‐ and tri‐block copolymers of poly(ethylene oxide) and poly(ε‐caprolactone)

Amphiphilic di‐ and tri‐block copolymers based on poly(ethylene oxide) as a hydrophilic segment and poly(ε‐caprolactone) as a hydrophobic part are synthesized by the ring‐opening polymerization of ε‐caprolactone while using poly(ethylene glycol)s and methoxy poly(ethylene glycol)s of varying molar masses as macro‐initiators. The synthesized block copolymers are characterized with respect to their total relative molar mass and its distribution by size exclusion chromatography. Liquid chromatography at critical conditions of both blocks is established for the analysis of individual block lengths and tracking presence of unwanted homopolymers of both types in the block copolymer samples. New critical conditions of polycaprolactone on reversed phase column are reported using organic mobile phase. The established critical conditions of polycaprolactone extended the applicable molar mass range significantly compared to already reported critical conditions of polycaprolactone in aqueous mobile phase. Block copolymers are also analyzed at critical conditions of poly(ethylene glycol). Complete analysis of the di‐ and tri‐block copolymers at corresponding critical conditions provided a fair estimate of molar mass of non‐critical block besides information regarding presence of homopolymers of both types in the samples.     

One‐pot,solvent‐free,metal‐free synthesis and UCST‐based purification of poly(ethylene oxide)/poly‐ε‐caprolactone block copolymers

A fast, one pot, solvent‐free and metal‐free synthesis of poly‐ε‐caprolactone and poly(ethylene oxide) block copolymers is reported. Copolymers with different molar mass, different hydrophilic to lipophilic balance, high degree of conversion and narrow molar mass dispersity have been obtained by organocatalyzed ring opening polymerization of ε‐caprolactone in presence of mono‐ or diol‐poly(ethylene oxide) as initiator and fumaric acid as catalyst. A new biocompatible and environmental friendly purification method is presented, exploiting the upper critical solution temperature of these class of copolymers in ethanol. The phase diagrams of the synthesized copolymers in ethanol are also reported. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 2992–2999     

Polystyrene‐graft‐poly(ethylene oxide) copolymers prepared by macromonomer technique in dispersion. I. Liquid chromatographic separation of product mixtures

Products of the radical dispersion copolymerization of methacryloyl‐terminated poly(ethylene oxide) (PEO) macromonomer and styrene were separated and characterized by size exclusion chromatography (SEC), full adsorption‐desorption (FAD)/SEC coupling and eluent gradient liquid adsorption chromatography (LAC). In dimethylformamide, which is a good solvent for PEO side chains but a poor solvent for polystyrene (PS), amphiphilic PS‐graft‐PEO copolymers formed aggregates, which were very stable at room temperature even upon substantial dilution. The aggregates disappeared at high temperature or in tetrahydrofuran (THF), which is a good solvent for both homopolymers and for PS‐graft‐PEO. FAD/SEC procedure allowed separation of homo‐PS from graft‐copolymer and determination of both its amount and molar mass. Effective molar mass of graft‐copolymer was estimated directly from the SEC calibration curve determined with PS standards. Presence of larger amount of the homo‐PS in the final graft‐copolymer products was also confirmed with LAC measurements. The results indicate that there are at least two or maybe three polymerization loci; namely the continuous phase, the particle surface layer and the particle core. The graft copolymers are produced mainly in the continuous phase while PS or copolymer rich in styrene units is formed mostly in the core of monomer‐swollen particles. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 2284–2291, 2000     

Self‐Assembly in Water of Poly(acrylic acid)‐Based Diblock Copolymers Synthesized by Nitroxide‐Mediated Polymerization

Summary: Amphiphilic diblock copolymers consisting of a hydrophilic block, poly(acrylic acid), and a hydrophobic block, polystyrene, were synthesized by direct nitroxide‐mediated polymerization using the PS block as a macro‐initiator for the first time. Several techniques were used to characterize the amphiphilic block copolymers (size exclusion chromatography, NMR spectroscopy). The proposed method can lead to samples with a broad range of composition and molar mass. Preliminary studies of their self‐assembly in aqueous medium using fluorescence spectroscopy and small‐angle neutron scattering are presented.

Schematic of the formation of the PS‐b‐PAA block copolymers and their micellization in aqueous media.     

Synthesis of new side‐group liquid crystalline block copolymers by living anionic polymerization

A new series of AB liquid crystalline (lc) block copolymers was synthesized via living anionic copolymerization of styrene as segment A and 6‐[4‐(4‐cyanophenylazo)phenoxy]hexyl methacrylate ( 1 ) as segment B. The copolymers were successfully prepared in quantitative yields and with narrow molar mass distributions. The number‐average molar mass of the segments was varied well‐defined. The polystyrene block ranged from 3 500 to 7 400 g/mol. The content of the B segment ranged from 1 to 54 wt.‐%. Thermotropic phases were detected by differential scanning calorimetry (DSC) for block copolymers with an lc segment of more than 30 wt.‐%.     

Block length determination of the block copolymer mPEG‐b‐PS using MALDI‐TOF MS/MS

The molar mass determination of block copolymers, in particular amphiphilic block copolymers, has been challenging with chromatographic techniques. Therefore, methoxy poly(ethylene glycol)‐b‐poly(styrene) (mPEG‐b‐PS) was synthesized by atom transfer radical polymerization (ATRP) and characterized in detail not only by conventional chromatographic techniques, such as size exclusion chromatography (SEC), but also by matrix‐assisted laser/desorption ionization tandem mass spectrometry (MALDI‐TOF MS/MS). As expected, different molar mass values were obtained in the SEC measurements depending on the calibration standards (either PEG or PS). In contrast, MALDI‐TOF MS/MS analysis allowed the molar mass determination of each block, by the scission of the weakest point between the PEG and PS block. Thus, fragments of the individual blocks could be obtained. The PEG block showed a depolymerization reaction, while for the PS block fragments were obtained in the monomeric, dimeric, and trimeric regions as a result of multiple chain scissions. The block length of PEG and PS could be calculated from the fragments recorded in the MALDI‐TOF MS/MS spectrum. Furthermore, the assignment of the substructures of the individual blocks acquired by MALDI‐TOF MS/MS was accomplished with the help of the fragments that were obtained from the corresponding homopolymers. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Physicochemical characterization of the thermo‐induced self‐assembly of thermo‐responsive PDMAEMA‐b‐PDEGMA copolymers

Diblock copolymers of poly[2‐(dimethylamino)ethyl methacrylate]‐block‐poly[di(ethylene glycol) methyl ether methacrylate], PDMAEMA‐b‐PDEGMA, were synthesized by reversible addition–fragmentation chain transfer polymerization. The block ratio was varied to study the influence on the lower critical solution temperature and the corresponding phase transition in water. Therefore, turbidimetry, differential scanning calorimetry (DSC), dynamic light scattering (DLS), and laser Doppler velocimetry were applied. Additionally, asymmetric flow field‐flow fractionation (AF4) coupled to DLS and multiangle laser light scattering (MALLS) was established as an alternative route to characterize these systems in terms of molar mass of the polymer chain and size of the colloids after the phase transition. It was found that AF4–MALLS allowed accurate determination of molar masses in the studied range. Nevertheless, some limitations were observed, which were critically discussed. The cloud point and phase transition of all materials, as revealed by turbidimetry, could be confirmed by DSC. For block copolymers with block ratios in the range of 50:50, a thermo‐induced self‐assembly into micellar and vesicular structures with hydrodynamic radii (R_h) of around 25 nm was observed upon heating. At higher temperatures, a reordering of the self‐assembled structures could be detected. The thermo‐responsive behavior was further investigated in dependence of pH value and ionic strength. Variation of the pH value mainly influences the solubility of the PDMAEMA segment, where a decrease of the pH value increases the transition temperature. An increase of ionic strength leads to a reduction of the cloud point due to the screening of electrostatic interactions. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 924–935     

Characterization of an unsaturated low‐density polyethylene

This study concerns a new group of low‐density polyethylenes (LDPEs)—unsaturated LDPE. The new LDPE is a copolymer between ethylene and 1,9‐decadiene and was polymerized in a commerical high‐pressure tubular reactor. The diene copolymerized with one double bond, leaving the other unreacted as a pendant side group. This yielded a copolymer containing a higher number of vinyl groups than ordinary LDPE. Fractionation of the copolymer and determination of the number of unsaturated structures in the different fractions by Fourier transform infrared spectroscopy revealed that the diene is homogeneously incorporated along the molar‐mass distribution curve. It is also possible to obtain copolymers with a varying vinyl content, without drastic changes in molar mass or molar‐mass distribution, by a controlled addition of 1,9‐decadiene to the reactor. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2974–2984, 2003     

Polyamide–polyester multiblock copolymers by chain‐coupling reactions of carboxy‐terminated polymers with phenylene and pyridylene bisoxazolines

Polyamide–polyester multiblock copolymers were synthesized through the reaction of α,ω‐dicarboxy polyamides and polyesters with various arylene bis(2‐oxazoline)s. 2,2′‐(2,6‐Pyridylene)bis(2‐oxazoline) was very reactive and yielded multiblock copolymers with number‐average molar masses ranging from 15,000 to 25,000 after 30 min of reaction in the bulk at 200 °C. The molar masses and thermal properties of the resulting random multiblock copolymers (glass‐transition temperature, melting temperature, and melting enthalpy) were close to those of their alternating homologues prepared by conventional polycondensation between diamino polyamides and dicarboxy polyesters. This showed that the presence of coupling agent moieties in the polymer chains did not exert a significant influence on the block copolymer morphology. The chain‐coupling method showed several advantages over conventional polycondensation: a much shorter reaction time, a lower temperature, no byproducts, and easy control of the final copolymer properties through the mass ratio of the starting oligomers. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 1331–1341, 2005     

Gas‐phase tautomerism in 1‐phenylazonaphthalene‐4‐ol: verification of the responses of individual tautomers

Gas‐phase tautomerism in 1‐phenylazonaphthalene‐4‐ol (1) was studied by using electron ionization (EI) mass spectrometry on the basis of the fragmentations of the model enol and keto tautomers, where the movable proton is replaced by a methyl group. These fixed tautomers were obtained as an easy separable mixture by simple methylation of the cheap and easily accessible diazene (1). It was found that their EI mass spectral fragmentations are in full congruence with the already published theoretical predictions. The relative energies required for bond cleavage in 1 and its fixed tautomers were estimated by stepwise increasing of the electron energy of the ion source of the mass spectrometer. A simple equation for the approximate estimation of the molar fractions of the individual tautomers was suggested. It was shown that the enol form is dominant in the temperature range of 200–300°C. Copyright © 2009 John Wiley & Sons, Ltd.     

Synthesis and MALDI‐TOF analysis of dendritic‐linear block copolymers of lactides: Influence of architecture on stereocomplexation

Formation of a stereocomplex from polylactide copolymers can be tuned by changing the size and the chain topology of the second block in the copolymer. In particular, the use of a dendritic instead of linear architecture is expected to destabilize the cocrystallisation of polylactide blocks. With this idea in mind, dendritic‐linear block copolymers were synthesized by ring‐opening polymerization (ROP) of lactides using benzyl alcohol dendrons of generation 1–3 as macroinitiators and stannous octoate as catalyst. Polymers with controlled and narrow molar mass distribution were obtained. The MALDI‐TOF mass spectra of these dendritic‐linear block copolymers show well‐resolved signals. Remarkably, 10% or less of odd‐membered polymers are present, indicating that ester‐exchange reactions which occur classically parallel to the polymerization process, were in these conditions, very limited. Thermal analysis of polyenantiomers of generation 1–3 and the corresponding blends were examined. The blend of a pair of enantiomeric dendritic‐linear block copolymers exhibit a higher melting temperature than each copolymer, characteristic for the formation of a stereocomplex. Melting temperatures are strongly dependent on the dendron generation. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 6782–6789, 2006     

Separation of ethylene‐propylene copolymers and ethylene‐propylene‐diene terpolymers using high‐temperature interactive liquid chromatography

Ethylene‐propylene‐diene terpolymers (EPDM) are generally amorphous and, therefore, do not crystallize from solution. Consequently, fractionation techniques based on crystallization, such as crystallization analysis fractionation or temperature rising elution fractionation, cannot be used to analyze their chemical composition distribution. Moreover, no suitable chromatographic system was known, which would enable to separate them according to their chemical composition. In this study, two different sorbent/solvent systems are tested with regard to the capability to separate EPDM‐terpolymers and ethylene‐propylene (EP)‐copolymers according to chemical composition. While porous graphite/1‐decanol system is selective towards ethylene and ethylidene‐2‐norbornene, carbon coated zirconia/2‐ethyl‐1‐hexanol is preferentially selective towards ethylene. Consequently, the earlier system enables to separate both EP copolymers and EPDM according to the chemical composition and the latter mainly according to the ethylene content. The results prove that the chromatographic separation in both sorbent/solvent systems is not influenced by molar mass of a sample or by its long chain branching. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Use of N‐methyliminodiacetic acid boronate esters in suzuki‐miyaura cross‐coupling polymerizations of triarylamine and fluorene monomers

Polytriarylamine copolymers can be prepared by Suzuki‐Miyaura cross‐coupling reactions of bis N‐methyliminodiacetic acid (MIDA) boronate ester substituted arylamines with dibromo arenes. The roles of solvent composition, temperature, reaction time, and co‐monomer structure were examined and (co)polymers prepared containing 9, 9‐dioctylfluorene (F8), 4‐sec‐butyl or 4‐octylphenyl diphenyl amine (TFB), and N, N′‐bis(4‐octylphenyl)‐N, N′‐diphenyl phenylenediamine (PTB) units, using a Pd(OAc)₂/2‐dicyclohexylphosphino‐2′,6′‐dimethoxybiphenyl (SPhos) catalyst system. The performance of a di‐functionalized MIDA boronate ester monomer was compared with that of an equivalent pinacol boronate ester. Higher molar mass polymers were produced from reactions starting with a difunctionalized pinacol boronate ester monomer than the equivalent difunctionalized MIDA boronate ester monomer in biphase solvent mixtures (toluene/dioxane/water). Matrix‐assisted laser desorption/ionization mass spectroscopic analysis revealed that polymeric structures rich in residues associated with the starting MIDA monomer were present, suggesting that homo‐coupling of the boronate ester must be occurring to the detriment of cross‐coupling in the step‐growth polymerization. However, when comparable reactions of the two boronate monomers with a dibromo fluorene monomer were completed in a single phase solvent mixture (dioxane + water), high molar mass polymers with relatively narrow distribution ranges were obtained after only 4 h of reaction. © 2017 The Authors. Journal of Polymer Science Part A: Polymer Chemistry Published by Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 2798–2806     

Synthesis and morphology of model PS‐b‐PDMS copolymers

True model linear poly(styrene‐b‐dimethylsiloxane) PS‐b‐PDMS copolymers were synthesized by using sequential addition of monomers and anionic polymerization (high‐vacuum techniques), employing the most recent experimental procedures that allow the controlled polymerization of each monomer to obtain blocks with controlled molar masses. The model diblock copolymers obtained were analyzed by using different techniques, such as size‐exclusion chromatography, ¹H NMR, Fourier transform infrared spectroscopy, small angle X‐rays scattering (SAXS), and wide angle X‐rays scattering (WAXS). The PS‐b‐PDMS copolymers obtained showed narrow molar mass distribution and variable PDMS content, ranging from 2 up to 55 wt %. Compacted powder samples were investigated by SAXS to reveal their structure and morphology changes on thermal treatment in the interval from 30 to 200 °C. The sample with the highest PDMS content exhibits a lamellar morphology, whereas two other samples show hexagonally packed cylinders of PDMS in a PS matrix. For the lowest PDMS content samples, the SAXS pattern corresponds to a disordered morphology and did not show any changes on thermal treatment. Detailed information about the morphology of scattering domains was obtained by fitting the SAXS scattering curves. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 3119–3127, 2010     

Synthesis and self‐assembly of thermosensitive double‐hydrophilic poly(N‐vinylcaprolactam)‐b‐poly(N‐vinyl‐2‐pyrrolidone) diblock copolymers

We report on novel diblock copolymers of poly(N‐vinylcaprolactam) (PVCL) and poly(N‐vinyl‐2‐pyrrolidone) (PVPON) (PVCL‐b‐PVPON) with well‐defined block lengths synthesized by the MADIX/reversible addition‐fragmentation chain transfer (RAFT) process. We show that the lower critical solution temperatures (LCST) of the block copolymers are controllable over the length of PVCL and PVPON segments. All of the diblock copolymers dissolve molecularly in aqueous solutions when the temperature is below the LCST and form spherical micellar or vesicular morphologies when temperature is raised above the LCST. The size of the self‐assembled structures is controlled by the molar ratio of PVCL and PVPON segments. The synthesized homopolymers and diblock copolymers are demonstrated to be nontoxic at 0.1–1 mg mL^?1 concentrations when incubated with HeLa and HEK293 cancer cells for various incubation times and have potential as nanovehicles for drug delivery. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 2725–2737     

Microstructure of metallocene isotactic propylene‐co‐1‐pentene‐co‐1‐hexene terpolymers

This study aims at characterizing in depth the microstructure of propylene‐co‐1‐pentene‐co‐1‐hexene terpolymers, which have been recently reported to develop the isotactic polypropylene δ trigonal polymorph when the total comonomer content is high enough. Such a specific crystalline form had been only reported so far in the analogous copolymers containing either 1‐pentene or 1‐hexene. A comparative ¹³C NMR study in solution of the aforementioned terpolymers and copolymers allows asserting the random insertion of both comonomers during chain growth under the polymerization conditions used. The reaction parameters, mainly catalyst and temperature, have been chosen for the purpose of assuring relatively high molar mass polymers. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 2537–2547     

High molar mass ethene/1‐olefin copolymers synthesized with acenaphthyl substituted metallocene catalysts

The influence of ligand structure on copolymerization properties of metallocene catalysts was elucidated with three C₁‐symmetric methylalumoxane (MAO) activated zirconocene dichlorides, ethylene(1‐(7, 9)‐diphenylcyclopenta‐[a]‐acenaphthadienyl‐2‐phenyl‐2‐cyclopentadienyl)ZrCl₂ ( 1 ), ethylene(1‐(7, 9)‐diphenylcyclopenta‐[a]‐acenaphthadienyl‐2‐phenyl‐2‐fluorenyl)ZrCl₂ ( 2 ), and ethylene(1‐(9)‐fluorenyl‐(R)1‐phenyl‐2‐(1‐indenyl)ZrCl2 ( 3 ). Polyethenes produced with 1 /MAO had considerable, ca. 10% amount of trans‐vinylene end groups, resulting from the chain end isomerization prior to the chain termination. When ethene was copolymerized with 1‐hexene or 1‐hexadecene using 1 /MAO, molar mass of the copolymers varied from high to moderate (531–116 kg/mol) depending on the comonomer feed. At 50% comonomer feed, ethene/1‐olefin copolymers with high hexene or hexadecene content (around 10%) were achievable. In the series of catalysts, polyethenes with highest molar mass, up to 985 kg/mol, were obtained with sterically most crowded 2 /MAO, but the catalyst was only moderately active to copolymerize higher olefins. Catalyst 3 /MAO produced polyethenes with extremely small amounts of trans‐vinylene end groups and relatively low molar mass 1‐hexene copolymers (from 157 to 38 kg/mol) with similar comonomer content as 1 . These results indicate that the catalyst structure, which favors chain end isomerization, is also capable to produce high molar mass 1‐olefin copolymers with high comonomer content. In addition, an exceptionally strong synergetic effect of the comonomer on the polymerization activity was observed with catalyst 3 /MAO. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 373–382, 2008     

An Efficient Thiol‐Ene Chemistry for the Preparation of Amphiphilic PHA‐Based Graft Copolymers

We present a straightforward method to prepare amphiphilic graft copolymers consisting of hydrophobic poly(3‐hydroxyalkanoates) (PHAs) backbone and hydrophilic α‐amino‐ω‐methoxy poly(oxyethylene‐co‐oxypropylene) (Jeffamine®) units. Poly(3‐hydroxyoctanoate)‐co‐(3‐hydroxyundecenoate) (PHOU) was first methanolyzed to obtain the desired molar mass. The amino end groups of Jeffamine were converted into thiol by a reaction with N‐acetylhomocysteine thiolactone and subsequently photografted. This “one‐pot” functionalization prevents from arduous and time‐consuming functionalization of the hydrophilic precursor or tedious modifications of PHAs, thus simplifying the process. The amphiphilic nature of modified PHAs leads to water‐soluble copolymers exhibiting thermoresponsive behavior.     

Synthesis and monomer reactivity ratios of methyl methacrylate and 2‐vinyl‐4,4′‐dimethylazlactone copolymers

We report the monomer reactivity ratios for copolymers of methyl methacrylate (MMA) and a reactive monomer, 2‐vinyl‐4,4′‐dimethylazlactone (VDMA), using the Fineman–Ross, inverted Fineman–Ross, Kelen–Tudos, extended Kelen–Tudos, and Tidwell–Mortimer methods at low and high polymer conversions. Copolymers were obtained by radical polymerization initiated by 2,2′‐azobisisobutyronitrile in methyl ethyl ketone solutions and were analyzed by NMR, gas chromatography (GC), and gel permeation chromatography. ¹H NMR analysis was used to determine the molar fractions of MMA and VDMA in the copolymers at both low and high conversions. GC analysis determined the molar fractions of the monomers at conversions of less than 27% and greater than 65% for the low‐ and high‐conversion copolymers, respectively. The reactivity ratios indicated a tendency toward random copolymerization, with a higher rate of consumption of VDMA at high conversions. For both low‐ and high‐conversion copolymers, the molecular weights increased with increasing molar fractions of VDMA, and this was consistent with the faster consumption of VDMA (compared with that of MMA). © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 3027–3037, 2003     

Synthesis and characterization of poly (1‐vinyl‐3‐butylimidazolium‐co‐methyl methacrylate) gel polymer electrolytes for dye‐sensitized solar cells: Effect of structure and composition

Herein, three ionic liquid random copolymers (P) containing 1‐vinyl‐3‐butylimidazolium bromide (VBImBr) and methyl methacrylate (MMA) with various molar ratios were prepared using conventional free radical polymerization. Afterward, their corresponding chemically cross‐linked copolymers (XP) were formed similarly in the presence of polyethylene glycol dimethacrylate (PEGDMA). The synthesized copolymers were characterized using FT‐IR, ¹H NMR, and GPC. Differential scanning calorimetry (DSC) and thermal gravimetric analysis (TGA) results showed that the rigidity and thermal stability of the copolymers depended on the ionic liquid content as well as the degree of cross‐linking. Gel polymer electrolytes were then prepared via obtained copolymers in the presence of a constant amount of synthesized imidazolium‐based ionic liquid. Among the copolymers, the P3 with in feed VBImBr:MMA molar ratio of 70:30 and the cross‐linked 1%‐XP3 copolymer prepared with 1 mol% of PEGDMA exhibited the highest conductivity and diffusion coefficients for I₃^¯ and I^¯. The power conversion efficiency of the optimized linear and cross‐linked copolymers (P3 and 1%‐XP3) under the simulated AM 1.5 solar spectrum irradiation at 100 mW cm^?2 were 3.49 and 4.13% in the fabricated dye‐sensitized solar cells (DSSCs), respectively. The superior long‐term stability and high performance of the gel electrolyte containing 1%‐XP3 suggested it as commercial gel electrolyte for future DSSCs.