Na5[B2P3O13]晶体双晶结构的研究

采用泡生法和b向籽晶生长出尺寸为22mm×24mm×20mm的透明Na5[B2P3O13]晶体.晶体定向中发现(100)和(001)晶面的一级衍射出现双峰;正交偏光显微镜下观察晶体的(010)切片,看到清晰的明暗条纹;当一束激光正入射(010)切片时,产生衍射现象;用同步辐射白光X射线形貌术拍摄了(100)、(010)和(001)切片的Laue像,观察到了晶体的孪晶结构,再借助(010)切片的化学腐蚀研究,推出该晶体为规则的聚片双晶,其结合面为(001).     

Na2 O-B2O3-SiO2-CaO-P2O5-F生物微晶玻璃制备与性能研究

采用烧结法,选用Na2O-B2O3-SiO2为基础玻璃(NBS),按照氟磷灰石组成配比添加CaO,P2O5,CaF2三种组分,制备Na2O-B2O3-SiO2-CaO-P2O5-CaF2生物微晶玻璃.利用差热分析、X射线衍射分析及扫描电镜等测试手段对微晶玻璃物相、微观结构进行了测试和分析,并采用模拟体液对样品的生物活性进行了验证.结果表明:随着热处理温度升高,样品的晶化程度逐步提高,当热处理温度在750℃时,可以获得主晶相为氟磷灰石,晶粒尺寸在100 nm左右、其晶化率≥80;的微晶玻璃样品,通过模拟体液浸泡实验证明了样品具有一定的生物活性.     

Al2TiO5/Al2O3陶瓷复合材料的晶粒异向生长

通过机械激活法制备了Al2TiO5/Al2O3(nAl2TiO5: nAl2O3=1: 4)的陶瓷复合材料.利用X射线衍射(XRD)、扫描电镜(SEM)以及能谱(EDS)分析了不同的温度制度下Al2TiO5/Al2O3陶瓷复合材料的晶粒生长特性.X射线衍射谱图(XRD)显示烧结样品的主晶相为α-Al2O3和Al2TiO5.SEM和EDS分析显示,较低温度下烧结(1350 ℃)时Al2TiO5晶粒为等轴状.当温度升高到1450 ℃时,Al2TiO5开始异向长大,形成棒状晶粒.随着温度的升高(1500 ℃),棒状Al2TiO5的长径比继续增加.而Al2O3则始终为片状和等轴晶粒,且异向生长的Al2TiO5晶粒填充于Al2O3三角晶界处.研究表明,烧结温度的升高会促进晶体异向生长并增加其体积分数.Al2TiO5会阻碍Al2O3基体颗粒进一步生长,所以当Al2TiO5颗粒平均尺寸随着烧结温度增加而增大,Al2O3基体晶粒生长几乎停滞.     

CsB3O5(CBO)晶体生长和形貌研究

本文采用籽晶浸没法,在Cs2O过量3;的Cs2O-B2O3体系中生长了CsB3O5单晶.生长参数如下:液面以下温度梯度为0.5℃/cm, 晶体旋转速度为12r/min,降温速率0.2℃/d,可获得透明、无包裹体、无开裂、最大尺寸达65×44×49mm3的CsB3O5单晶.研究了CsB3O5的生长形貌,CsB3O5生长没有明显的方向性,总是呈现长柱状,最易出现的晶面是(011)和(101)晶面.     

P2O5对CaO-MgO-Al2O3-SiO2系微晶玻璃析晶的影响

采用熔融法制备了不同P2O5含量的CaO-MgO-Al2O3-SiO2玻璃样品,研究了P2O5对该系微晶玻璃析晶的影响规律.结果表明:在所研究的CaO-MgO-Al2O3-SiO2玻璃中,P2O5的最大溶解量在10.0;质量分数左右,超过其饱和溶解度后将析出α-磷酸钙相.玻璃中添加4.0;质量分数P2O5时以表面析晶为主,析出晶体为钙长石和少量硅灰石.随着P2O5含量的提高, α-磷酸钙逐渐析出,同时钙长石和硅灰石的析出逐渐降低.进一步提高P2O5含量抑制了玻璃的表面析晶,促进了玻璃的分相和整体析晶.当P2O5的含量达到10;时,玻璃以整体析晶为主,在分相区内外区域析出晶体的形态非常相似,均呈现为细小粒状.     

Nd3+:Na3La9O3(BO3)8晶体生长和光谱性能

采用顶部籽晶法生长Nd3+:Na3La9O3(BO3)8 晶体.在室温下测试了吸收光谱、发射光谱和荧光寿命.应用Judd-Ofelt理论评价了Nd3+:Na3La9O3(BO3)8晶体的光谱性能.812 nm处较宽的吸收峰适合AlGaAs LD泵浦的吸收.分别计算了Nd3+离子的唯象强度、谱线强度、辐射寿命、荧光分支比和荧光量子效率.     

Na3Sm2(BO3)3的晶体生长及热学和光谱性质

以Na2CO3-H3BO3为助溶剂,用顶部籽晶法生长了14mm×8mm×2mm的Na3Sm2(BO3)3晶体.差热分析(DTA)表明Na3Sm2(BO3)3非同成分熔融,熔点为1089.1℃.该晶体易溶于酸,在空气条件下能稳定存在,不易潮解.测量了室温下晶体在200～2500nm范围内的吸收光谱,并对跃迁能级进行了初步指认.     

Growth,Morphology, Structure and Properties of Na3BaCl5 2H2O Crystals

Single crystals of Na₃BaCl₅ 2H₂O were obtained from saturated aqueous solutions at two different temperatures (27° C and 32° C). The crystal size increases with increasing temperature. The crystals obtained were subjected to a systematic morphological, X-ray and thermal analyses. The study of as-grown crystal morphology and surface morphology of Na₃BaCl₅ 2H₂O crystals clearly indicate the requirement of a slow rate of evaporation at temperatures 27 to 28° C, moderate supersaturation in order to obtain high quality single crystals of Na₃BaCl₅ 2H₂O. The X-ray diffraction studies give the following cell parameters for the title compound: monoclinic, P21/n, a = 8.5773(9), b = 9.5502(4), c = 5.2873(3) A, β =92.069°, V = 432.8 A³, Z = 2. The study of TGA curves indicate the occurrence of dehydration process at around 200° C and not the decomposition of the compound. Similarly, the low temperature DSC study indicates a thermal anomaly at 267 K, and the high temperature DSC study (323 K to 873 K) indicates the transition from dihydrate to monohydrate and in turn anhydrous state at 454.6 K for Na₃BaCl₅ 2H₂O crystals. Thus both the TGA and DSC curves conclude that the Na₃BaCl₅ 2H₂O crystals contain two molecules of water of crystallization and its molecular formula is Na₃BaCl₅ 2H₂O.     

Real Structure of LiB3O5 (LBO) Crystals Grown in Li2O‐B2O3‐MoO3 System

The liquidus surface structure and field of LiB₃O₅ (LBO) primary crystallization have been revealed in Li₂O‐B₂O₃ ‐MoO₃ ternary system. The optimization of charge composition and growth conditions results in large volume optical quality LBO single crystals yielding. Crystallographic properties and real defect structure of grown LBO single crystals have been investigated by X‐ray powder diffraction method and X‐ray reflection topography. The volume of the crystals is partly free of any structural imperfections.     

Ho~(3+)∶La_2CaB_(10)O_(19)晶体生长和光谱性能(英文)

采用顶部籽晶法生长Ho3+∶La2CaB10O19晶体。测试了晶体的X射线衍射谱图以及晶体器件的摇摆曲线,半峰宽为21.6 arcsec,晶体结晶质量良好。在室温下测试了吸收光谱、发射光谱和荧光寿命。应用Judd-Ofelt理论评价了Ho3+∶La2CaB10O19晶体的光谱性能。分别计算了Ho3+的唯象强度、谱线强度、辐射寿命、荧光分支比等参数。     

钛宝石晶体的泡生法生长和闪烁发光性能

采用泡生法生长了115 kg级大尺寸钛宝石(Ti:Al2 O3)晶体,晶体外形完整无开裂,制备了口径达?300 mm的高质量大口径钛宝石单晶样品.在X射线和α粒子激发下测试了晶体的闪烁发光性能.结果表明,Ti:Al2 O3晶体的闪烁发光包含近红外和近紫外发光.近红外发光来源于Ti3+特征发射,效率较高,衰减时间慢.近紫...     

Ce3+∶GdLu2Al5O12/Al2O3共晶微结构及其发光性能

稀土共晶闪烁体是通过定向凝固晶体生长技术,将具有不同折射率的两相制备成具有射线探测功能的共晶材料,其中含有激活离子的闪烁体相的折射率高于基质相。在高能射线辐照下,闪烁体相将入射高能射线转换成荧光,然后,荧光在闪烁体相和基底相的界面以全反射的形式实现定向输出,从而有效提高辐射探测成像的空间分辨率。本工作采用微下降法成功生长得到φ3 mm×117.0 mm 的1.0%(原子数分数)Ce∶GdLu₂Al₅O₁₂/Al₂O₃闪烁共晶样品。通过切割抛光加工得到φ3 mm×2.0 mm的共晶薄片,并将该共晶薄片进行微观结构、能谱分析和荧光性能等表征和测试,结果表明所得到的共晶样品由Ce∶GdLuAG和Al₂O₃两晶相构成,微观结构呈现出“中国结”结构,并在生长方向呈现出一定的有序排列。荧光光谱测试表明该共晶材料存在Gd³⁺-Ce³⁺间的能量传递,具有典型的Ce³⁺辐射跃迁,其中双宽峰发射峰最强位于560 nm。此外,根据生长速率对共晶样品发射峰强、峰位以及荧光寿命影响,优化出最佳下拉生长速率为4.0 mm/min。     

UV-vis辐照下H2Fe2Ti3O10/TiO2插层材料光催化活性的研究

在高压汞灯辐照下,通过插入反应将H2Fe2Ti3O10与n-C3H7NH2/C2H5OH和TiO2溶胶制备出H2Fe2Ti3O10/TiO2插层复合物.插入TiO2的层状钙钛矿化合物H2Fe2Ti3O10在UV-vis辐照下表现出高活性.实验结果表明H2Fe2Ti3O10/TiO2作为光催化剂在可见光(λ＞420nm)下辐照24h,降解甲基橙的速率为59.0;.与相同条件下降解率只有24;的商用光催化剂TiO2(Degussa P-25)相比,H2Fe2Ti3O10/TiO2表现出了更高的光催化活性.     

Selective etching of ZnTe in HF:H2O2:H2O solution: Interpretation of extended defect‐related etch figures

HF:H₂O₂:H₂O solution (40%wt.HF: 30wt.%H₂O₂: H₂O, 3:2:1 by volume) was used to reveal extended defects (line, face and volume defects) in bulk ZnTe crystals grown from Te solution. The etch patterns were analyzed based on their size, shape and distribution. The etch figures, both in the shape of pits and hillocks with high resolution, show forms controlled by the symmetries of the respective faces were produced. Two different sizes of pits were observed, the larger‐size pits correspond to dislocations penetrating the surface, however, the smaller‐size texture pits are produced on the defect‐free region, which serve as standard pits on respect faces. The face defects, such as grain boundaries, sub‐grain boundaries, dislocation walls, twins and stacking faults, can be all displayed clearly. Another essential feature of the etchant is that, it can effectively dissolve Te‐rich phase (Te inclusion/precipitates), which makes it promising to reveal the shape of this volume defect.     

Er:Lu2 O3单晶的导模法生长及性能表征

本文以高纯Lu₂O₃、Er₂O₃为原料,使用自主设计、制造的自动等径导模炉,采用导模法(EFG)生长了φ25 mm×20 mm的7.82%(原子数分数)Er:Lu₂O₃单晶,分凝系数为0.92,并探索了退火条件。X射线衍射仪(XRD)结果为纯相,X射线荧光光谱仪(XRF)结果证明杂质含量较低。利用吸收光谱计算在972 nm及1 535 nm附近的吸收截面,分别为3.24×10^-21 cm²、8.43×10^-21 cm²,半峰全宽(FWHM)分别为28.22 nm、27.31 nm。热学性能测试结果表明,在30 ℃时热导率为13.28 W·m^-1·K^-1。利用扫描电子显微镜(SEM)对晶体表面微观形貌进行了表征。     

H2SO4-H2O中硝酸铜对脱硫石膏晶须生长的影响

以处理后的脱硫石膏为原料,在H₂SO₄-H₂O体系中以Cu(NO₃)₂为晶形控制剂采用水热法制备脱硫石膏晶须,探讨了Cu(NO₃)₂对脱硫石膏晶须生长的影响机理。结果表明:Cu(NO₃)₂对脱硫石膏有明显促溶作用,其中Cu²⁺可减小溶液中各离子的活度系数,使溶液中的Ca²⁺浓度增大。NO^-₃通过静电作用在Ca²⁺周围聚集并对SO^2-₄产生屏蔽作用,导致脱硫石膏继续溶解并使Ca²⁺和SO^2-₄的浓度处于相对稳定状态,有利于半水脱硫石膏晶体的形核与生长。此外,Cu²⁺还可在晶须的生长过程中选择性吸附在晶须表面,生成CuSO₄,促进了脱硫石膏的结晶生长,最终在Cu(NO₃)₂用量为2.0%(质量分数)时制备的脱硫石膏晶须长径比约为73。     

A7MIIRE2(B5O10)3系列紫外非线性光学晶体的研究进展

稀土硼酸盐非线性光学(NLO)材料由于其在激光技术领域的重要应用而备受关注,这主要是因为三价稀土离子如Y³⁺、Sc³⁺、Lu³⁺等可以有效抑制d-d和f-f电子跃迁从而扩宽化合物的透过范围,同时稀土原子与氧原子结合成畸变的多面体可增强材料的非线性光学效应。A₇M^IIRE₂(B₅O₁₀)₃系列(RE为稀土金属,A为碱金属、M为二价金属)化合物是稀土硼酸盐中一类重要的材料,其A、M以及RE位点具备灵活的占据方式,近年来得到了广泛关注。通过化学元素取代法,研究者们对该类化合物的种类进行拓展,目前已经合成出数十种属于该体系的化合物。这些化合物的截止边大多处在紫外甚至是波长小于200 nm的深紫外波段,非线性光学效应为0.4~2.1倍KDP,在紫外以及深紫外波段非线性光学领域中展现出了应用潜力。本文对其研究现状进行了总结,分析了其微观结构与光学性能之间的关系,并指出不同位点组分对材料非线性光学性能的影响,以期对此类化合物今后的发展提供参考。     

三维网络结构NiCo2S4@NiCo2O4复合电极的制备及其性能

超级电容器具有更大的功率密度、优秀的循环稳定性、极快的充放电速度、超长的循环寿命以及环境友好等突出特点,其性能与构件关系密切,其中最根本的就是组成它的电极材料。本研究主要采用传统的水热法制备出钴酸镍(NiCo₂O₄)电极材料,进而通过离子交换(二次水热)制得镍钴硫(NiCo₂S₄),最后利用化学浴沉积(CBD)法使其与钴酸镍复合,得到最终所需的三维网络结构NiCo₂S₄@NiCo₂O₄复合电极。经过表面形貌表征、循环伏安测试、恒电流充放电测试以及比电容计算分析等可以证明:三维网络结构NiCo₂S₄@NiCo₂O₄复合电极的比电容及循环稳定性等远远优于复合前单一的纯NiCo₂O₄电极材料,具有极大应用前景。     

Growth and dielectric properties of Ta2O5 single crystal by the floating zone method

Large Ta₂O₅ single crystal with high‐dielectric permittivity was successfully grown by floating zone (FZ) method under air atmosphere. The grown crystal that has been obtained was typically about 8 mm in diameter and 90 mm in length. The crystal growth parameters were optimized. The crystal symmetry, characterized by means of X‐ray diffraction (XRD), was found to be tetragonal. The relative permittivity and loss tangent along growth and [001] direction were measured in the temperature range between ‐200 °C and 200 °C, which showed a strong dielectric anisotropy. At a frequency of 1 MHz and 20 °C, the dielectric permittivity along the growth direction and [001] direction are 81.17 and 25.04 respectively. The stabilization of high‐temperature phase can explain the dielectric enhancement.     

Second harmonic generation in Na3Gd2(BO3)3 crystals

Na₃Gd₂(BO₃)₃ crystals with dimensions up to 22 × 20 × 5 mm³has been grown from NaBO₂ flux by the top‐seeded solution growth (TSSG) method for the first time. Differential scanning calorimetry (DSC) result shows that Na₃Gd₂(BO₃)₃ melts incongruently. The infrared spectrum indicates that Na₃Gd₂(BO₃)₃ contains characteristic triangular [BO₃]^3– groups responsible for the nonlinear optical effect. For the as‐grown crystal, the transmittance exceeds 80% in the wavelength range of 315 nm to 2670 nm, and the UV cutoff wavelength is 207 nm. The damage threshold is 0.47 GW cm^–2 at 1064 nm. Moreover, Na₃Gd₂(BO₃)₃ crystal exhibits an optical second harmonic generation effect which is 1.3 times as large as that of KH₂PO₄ (KDP). (© 2011 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)