N2O在Au/Co3O4和Au/ZnCo2O4催化剂上的分解反应

通过调变HAuCl₄溶液的pH值和Au负载量,用沉积-沉淀法制备了一系列Au/Co₃O₄催化剂,并采用AES、BET、XRD、SEM、XPS和H₂-TPR等技术对催化剂的结构和组成进行了表征,考察了制备条件对其在有氧气氛中催化N₂O分解反应性能的影响规律,得到了催化剂最佳制备条件:HAuCl₄溶液pH值为9,Au负载量为0.29%。催化测试结果表明:虽然ZnCo₂O₄的催化活性优于Co₃O₄,但0.31%Au/ZnCo₂O₄的活性和稳定性低于0.29%Au/Co₃O₄。500℃、在含氧气氛中连续反应10 h, 两者均可完全分解N₂O,但在含氧、含水气氛中0.29%Au/Co₃O₄和0.31%Au/ZnCo₂O₄上的N₂O转化率分别为92%和63%。究其原因,发现Au/Co₃O₄中Au和Co组分间存在协同效应,而Au/ZnCo₂O₄中Au和Co组分间则没有协同效应。     

Activation and properties of Mo=O bonds in Mo/SiO2 catalysts

The existence of the charge transfer excited triplet state [Mo⁵⁺-O^-] produced by UV-irradiation of Mo/SiO₂ catalysts, and its reactivity are evidenced by experiments of photoluminescence, photoinduced metathesis, and photoreduction of CO. Mo⁵⁺ ions can be produced separately by thermal activation and O^- ions by further adsorption of N₂O on those Mo⁵⁺ ions. The latter of which are adsorbed on Mo⁶⁺ ions are found to be more reactive than O^2- of [Mo⁶⁺ =O^2-] bond. They are able either to add a molecule such as CO or C₂H₄, or to abstract hydrogen from H₂, CH₄ or trans-dicyanoethylene, or a CN group form tetracyanoethylene (TCNE). The Mo⁵⁺ ions are able to coordinate gas phase ligands when their coordination sphere possesses vacant sites. This is the case for tetracoordinated Mo⁵⁺ _4c ions arising from reduction of tetrahedral Mo⁶⁺ ions (Eq. (7)). These Mo⁵⁺ _4c ions are similar to those produced by UV-irradiaiion (Eq. (2)). In addition, if the adsorbed molecule has a sufficiently large electron affinity, such as TCNE or O₂, an electron transfer can occur (Eq. (9) and (17)). The [Mo⁵⁺-O^-] bond obtained by thermal activation is more difficult to evidence than that obtained with UV-activation because it is not detectable by EPR. However, the EPR results obtained at low temperature show that the O^- ions adsorbed on Mo/SiO₂ catalysts as well as the [Mo⁵⁺-O^-] excited triplet state obtained by UV-irradiation of 1Mo⁶⁺=O²] interact with methanol (Eq. (16)). They are consistent with the mechanism of methanol oxidation occurring at high temperature (Eq. (4)).     

Characterization of CuO supported on tetragonal ZrO2 catalysts for N2O decomposition to N2

A series of tetragonal zirconia-supported CuO oxide catalysts with various CuO loadings were characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), electron spin resonance (ESR), ultraviolet and visible diffuse reflectance spectroscopy (UV/vis-DRS), and temperature-programmed reduction (TPR) measurements. The results indicate that the dispersion capacity of copper oxide on this support is approximately 8.6 Cu(2+) ions/nm(2) ZrO(2). The state of the resulting supported copper species depends on the CuO loading. At CuO loadings below the dispersion capacity, only highly dispersed copper ion species are present on the surface of t-ZrO(2). In particular, isolated Cu ions are the predominant species at low loadings. In contrast, pair Cu ions become the most abundant species at loadings near the dispersion capacity. It has been proposed that these dispersed CuO (isolated and paired Cu ions) have a symmetric 5-fold-oxygen-coordination symmetry (C(3)(v) symmetry) and can be described as distorted octahedra with a missing corner or a trigonal bipyramids. Finally, at CuO loadings above the dispersion capacity the formation of crystalline CuO is observed. TPR results reveal that the dispersed Cu ion species have a different reducibility from CuO crystallites, presumably due to strong interactions between these species and the t-ZrO(2) support. The catalytic activity of these CuO/t-ZrO(2) catalysts for the decomposition of N(2)O can also be directly correlated to CuO dispersion, with paired Cu ions being the most active species for this reaction.     

Enhancement of alpha-oxygen formation and N2O decomposition on Fe/ZSM-5 catalysts by extraframework Al

The concentration of alpha-oxygen which can oxidize methane to methanol and benzene to phenol at RT, increases linearly with the amount of introduced extraframework Al on Fe/ZSM-5 catalysts prepared by solid-state exchange of FeCl3 and AlCl3 with H-ZSM-5.     

Study of Ni-Ag/SiO2 catalysts prepared by reduction in aqueous hydrazine

We have studied bimetallic Ni-Ag (Ni + Ag = 1 wt%) catalysts supported on crystallized silica and prepared by aqueous chemical reduction with hydrazine at 353 K. Two protocols of reduction were used. Prepared catalysts were characterized by means of XRD, TEM, STEM, H2 chemisorption and H2-TPD. Their catalytic activity was studied in the gas-phase hydrogenation of benzene. The most important feature of the results obtained is the synergistic effect between Ni and Ag which led to improvement of dispersion and reactivity of nickel in the presence silver for precipitated catalysts. Silver is inactive in the test-reaction. Precipitated bimetallic catalysts give rise to total conversion from 373 K, a temperature at which conversion hardly reaches 30% for the impregnated catalysts. Dispersion and activity pass through a maximum of monotonically decrease with precipitated and impregnated catalysts, respectively. Deactivation was observed for bimetallic catalysts, particularly with precipitated samples. These results could be explained by the mechanism of metal reduction in the hydrazine media. As a result, various Ni-Ag species formed where Ni and Ag phases were separated clusters or interacted as heteroatomic groupings on the carrier surface. These grouping would be responsible of the high performances of the precipitated catalysts.     

载体性质对Pt催化剂H2选择催化还原NOx活性和选择性的影响

研究了Pt/MgO, Pt/γ-Al2O3, Pt/ZrO2和Pt/HZSM-5催化剂上H2选择催化还原消除NOx(H2-SCR)反应。结果发现, H2-SCR活性和N2生成选择性受催化剂中Pt的金属性以及载体的氮氧化物吸附能力影响很大。 HZSM-5的表面酸性使载体对NOx吸附能力较小,使担载Pt以较高的金属性存在,从而导致Pt/HZSM-5催化剂的高活性和高选择性。相反, Pt/MgO和Pt/γ-Al2O3催化剂较差的活性和选择性可归因于其载体的碱性表面、催化剂中Pt较低的金属性以及载体对氮氧化物较大的吸附能力。结合反应的原位红外光谱结果可以认为,在Pt/载体界面处亚硝酸根/硝酸根物种被还原为N2或N2O,取决于该处参与反应的活性H与这些含氮物种的相对数目。     

载体性质对Pt催化剂H2选择催化还原NOx活性和选择性的影响

研究了Pt/MgO, Pt/γ-Al2O3, Pt/ZrO2和Pt/HZSM-5催化剂上H2选择催化还原消除NOx(H2-SCR)反应。结果发现, H2-SCR活性和N2生成选择性受催化剂中Pt的金属性以及载体的氮氧化物吸附能力影响很大。 HZSM-5的表面酸性使载体对NOx吸附能力较小,使担载Pt以较高的金属性存在,从而导致Pt/HZSM-5催化剂的高活性和高选择性。相反, Pt/MgO和Pt/γ-Al2O3催化剂较差的活性和选择性可归因于其载体的碱性表面、催化剂中Pt较低的金属性以及载体对氮氧化物较大的吸附能力。结合反应的原位红外光谱结果可以认为,在Pt/载体界面处亚硝酸根/硝酸根物种被还原为N2或N2O,取决于该处参与反应的活性H与这些含氮物种的相对数目。     

酸预处理对于 Fe-ZSM-5和 Fe-beta分子筛催化消除 N2O的影响

作为六大温室气体之一, N2O的增温潜能是 CO2的310倍,甲烷的21倍,目前仍然以0.80 ppb/年的速度增长,但是减排成本很低,因此对 N2O的消除具有重要意义.在工业中金属修饰的微孔分子筛因其优良的催化活性,高水热稳定性,低成本等优点而成为研究重点.但是微孔分子筛狭窄的微孔孔道限制了金属前驱体的进入,导致活性金属含量低,进而限制了活性的提高.因此采用一定的改性手段减小分子筛颗粒尺寸,缩短微孔孔道长度或者扩大微孔孔道来增加活性铁物种的含量进而提高分子筛催化活性.
　　本文选用商用的 ZSM-5和 beta分子筛作为母板分子筛,按照3 g ：50 mL比例将分子筛母板与1.0 mol/L的 HNO3在室温下混合,分别搅拌0,2和24 h,然后采用液相离子交换法负载金属铁制备得到 Fe-ZSM-5和 Fe-beta.通过 X射线衍射、N2物理吸吸脱附、电感耦合等离子原子发射光谱仪、扫描电镜、透射电镜、NH3程序升温脱附及紫外漫反射(UV-vis)等手段对不同时间处理的分子筛的形貌、酸性和铁物种等物理化学性质进行表征.对两种催化剂催化消除 N2O的反应性能进行了测试.结果显示,温和的酸处理下分子筛脱除了部分 Al,其中, ZSM-5分子筛的表现为由外向内逐层刻蚀,颗粒尺寸减小,孔道长度缩短,但是由于 MFI型分子筛较高的稳定性,酸处理对分子筛孔道大小的改变并不明显,而对于 beta分子筛,首先是其中大量无定形物种的去除,然后对孔道进行修饰,使之略微扩大,但是对颗粒尺寸的影响不大.
　　 ICP结果显示,商用 ZSM-5和 beta分子筛经过温和的酸处理改性后, Si/Al比增大,负载 Fe的含量明显增加,各催化剂催化消除 N2O的活性也出现了不同程度的提高. Fe-ZSM-5和 Fe-beta分子筛上 N2O完全转化温度分别向低温段移动了10–15和30°C. UV-vis谱图显示,分子筛中存在着不同种类的铁物种,通过分峰计算发现,孤立的 Fe3+铁离子和低聚态的 Fex3+Oy均是催化活性铁物种,其含量的增加部分也解释了活性提高的原因.     

Photocatalytic reduction of CO2 with H2O on TiO2 and Cu/TiO2 catalysts

Photoinduced reduction of CO₂ by H₂O to produce CH₄ and CH₃OH has been investigated on wellcharacterized standard TiO₂ catalysts and on a Cu²⁺ loaded TiO₂ catalyst. The efficiency of this photoreaction depends strongly on the kind of catalyst and the ratio of H₂O to CO₂. Anatase TiO₂, which has a large band gap and numerous surface OH groups, shows high efficiency for photocatalytic CH₄ formation. Photogenerated Ti³⁺ ions, H and CH₃ radicals are observed as reactive intermediates, by ESR at 77 K. Cu-loading of the small, powdered TiO₂ catalyst (Cu/TiO₂) brings about additional formation of CH₃OH. XPS studies suggest that Cu⁺ plays a significant role in CH₃OH formation.     

Structural studies of high dispersion H3PW12O40/SiO2 solid acid catalysts

Highly dispersed H(3)PW(12)O(40)/SiO(2) catalysts with loadings between 3.6 and 62.5 wt% have been synthesised and characterised. The formation of a chemically distinct interfacial HPW species is identified by XPS, attributed to pertubation of W atoms within the Keggin cage in direct contact with the SiO(2) surface. EXAFS confirms the Keggin unit remains intact for all loadings, while NH(3) adsorption calorimetery reveals the acid strength >0.14 monolayers of HPW is loading invariant with initial DeltaH(ads) = approximately -164 kJ mol(-1). Lower loading catalysts exhibit weaker acidity which is attributed to an inability of highly dispersed clusters to form crystalline water. For reactions involving non-polar hydrocarbons the interfacial species where the accessible tungstate is highest confer the greatest reactivity, while polar chemistry is favoured by higher loadings which can take advantage of the H(3)PW(12)O(40) pseudo-liquid phase available within supported multilayers.     

钴铝复合氧化物负载金催化剂的制备及催化分解N2O

分别用离子交换法和共沉淀法制备了钴铝复合氧化物负载金催化剂,用于催化分解N₂O。离子交换法制备的催化剂活性优于共沉淀法制备的催化剂。对于离子交换法制备的催化剂,考察了金负载量、HAuCl₄溶液的预处理方式、焙烧温度对催化剂活性的影响,用BET、XRD、H₂-TPR等技术对催化剂进行了表征,优化出了催化剂的最佳制备参数：金负载量1.1%、预调节HAuCl₄溶液的pH值至9.0、300℃焙烧。在钴铝氧化物中加入适量的助剂Na,提高了Co³⁺的还原性和催化剂的低温活性,在此基础上制备的1.5%Na/1.1%Au/Co-Al催化剂的低温活性优于1.1%Au/Co-Al和1.5%Na/Co-Al。     

不同沉淀剂对Co3O4催化剂催化分解N2O活性的影响

采用了不同沉淀剂（K2 CO3、Na2 CO3、NaOH、NaHCO3）制备了一系列 Co3 O4氧化物催化剂。通过 XRD、XPS、BET、H2-TPR、O2-TPD 表征手段,探究了催化剂物相结构和氧化还原性能对 N2 O 催化分解性能的影响。研究表明,以 K2 CO3为沉淀剂制备的 Co3 O4催化剂具有优越的氧化还原性能。此外,较低结晶度有助于提高催化剂的催化性能,催化剂表面物种与其沉淀剂相关：丰富的表面 Co 物种促进催化活性,较多氧空位有利于催化剂表面的电子传递和氧气的脱附。以 K2 CO3为沉淀剂制备的 Co3 O4催化剂表现出最佳的 N2 O 催化分解活性,在450℃达到90％以上的转化率。     

Direct catalytic decomposition of N2O over Co(x)/RPSA catalysts

Research on Chemical Intermediates - As one of the main greenhouse gases, reducing emissions of N2O is imperative, for which catalytic decomposition is one of the most effective methods. A series...     

Shock tube studies of the N2O/Ar and N2O/H2/Ar systems

N₂O decay has been monitored via infrared emission for a series of mixtures containing N₂O/Ar and N₂O/H₂/Ar. These mixtures were studied behind reflected shock waves in the temperature interval of 1950–3075°K with total concentrations ranging from 1.2 to 2.5 × 10¹⁸ molec/cm³. In all cases the N₂O decayed exponentially, and a rate constant k_obs was obtained. Runs without added H₂ could be described by the following Arrhenius parameters: log A = ?9.72 ± 0.08 (in units of cm³/molec · sec) and E_A = 203.5 ± 3.6 kJ/mole. Addition of 0.01% and 0.1% H₂ was observed to increase the decay rate; the largest increase occurred between 2250 and 2500°K with 0.1% H₂, where k_obs doubled. Mixtures with no added H₂ were analyzed by numerical integration of the following reactions: Quantitative agreement between calculations and observations were obtained with both high and low choices for k₂ and k₃. The additional reactions were included in the analysis of the mixtures containing H₂. Here agreement was obtained only when low values were assigned to k₂ and k₃. The combinations of k₁ ← k₃ which agreed with all the data were k₁ = 3.25 × 10^?10 exp (?215 kJ/RT) and k₂ = k₃ = 1.91 × 10^?11 exp (-105 kJ/RT).     

Reduction of beta-hydroxyketones by SmI2/H2O/Et3N

Reduction of a series of beta-hydroxyketones by SmI2/H2O/Et3N provided 1,3-diols in quantitative yields. The reactions were exceedingly clean with no byproduct formation, negating the need for further purification. Most reactions provided moderate to excellent diastereoselectivity with syn-diols as the major isomer in most instances.     

O2 reduction to H2O by the multicopper oxidases

In nature the four electron reduction of O2 to H2O is carried out by Cytochrome c oxidase (CcO) and the multicopper oxidases (MCOs). In the former, Cytochrome c provides electrons for pumping protons to produce a gradient for ATP synthesis, while in the MCOs the function is the oxidation of substrates, either organic or metal ions. In the MCOs the reduction of O2 is carried out at a trinuclear Cu cluster (TNC). Oxygen intermediates have been trapped which exhibit unique spectroscopic features that reflect novel geometric and electronic structures. These intermediates have both intact and cleaved O-O bonds, allowing the reductive cleavage of the O-O bond to be studied in detail both experimentally and computationally. These studies show that the topology of the TNC provides a unique geometric and electronic structure particularly suited to carry out this key reaction in nature.     

Neue Verbindungen im System CaO/SiO2/CaCl2/H2O

New Compounds in the System CaO/SiO₂/CaCl₂/H₂O The hydrothermal formation of novel calcium silicate hydrates of compositions 5 CaO · 2 SiO₂ · CaCl₂ · 4 H₂O, 5 CaO · 2 SiO₂ · CaCl₂ · 2 H₂O and 4 CaO · 2 SiO₂ · CaCl₂ · H₂O from Ca₃SiO₅ and mixtures of CaO and SiO₂, respectively, in presence of calciumchloride at 200°–350 °C is described. From molybdate-reaction, ²⁹Si MAS NMR, DTA and TG measurements it is concluded that these compounds are based on disilicate anions and are to be interpreted as calcium hydroxide disilicate chlorides.