Structural studies of an oligomer (vinyl chloride tetramer) isolated from poly(vinyl chloride) resin used for food packaging applications

A presumptive single component previously isolated from PVC base resin and tentatively identified from GC-MS data as a vinyl chloride tetramer (mol. wt = 248) has been the subject of further studies. After hydrogenation, two isomeric compounds were separable by capillary GC. Mass spectra confirmed the earlier assignment of one double bond in the parent compounds. Further evidence for the presence of a pair of isomers in the apparently pure tetramer was obtained by epoxidation where two products giving identical mass spectra were produced. The MS fragmentation pattern suggested that the double bond position was allylic to chlorine; GC-MS analysis of the derived chlorohydrins supported this conclusion. Analysis of the tetramer by NMR gave complex overlapping signals, thought to be due to impurities, which hindered interpretation. Some supportive evidence for an allylic double bond was obtained. The structure of the tetramer thus remains only partially determined; the complexities of isomer purification and the difficulties of assigning chlorine substituent patterns make future unequivocal characterisation unlikely.     

Viscometric study of poly(vinyl chloride)/poly(vinyl acetate) blends in various solvents

The intermolecular interactions between poly(vinyl chloride) (PVC) and poly(vinyl acetate) (PVAc) in tetrahydrofuran (THF), methyl ethyl ketone (MEK) and N,N^′-dimethylformamide (DMF) were thoroughly investigated by the viscosity measurement. It has been found that the solvent selected has a great influence upon the polymer-polymer interactions in solution. If using PVAc and THF, or PVAc and DMF to form polymer solvent, the intrinsic viscosity of PVC in polymer solvent of (PVAc+THF) or (PVAc+DMF) is less than in corresponding pure solvent of THF or DMF. On the contrary, if using PVAc and MEK to form polymer solvent, the intrinsic viscosity of PVC in polymer solvent of (PVAc+MEK) is larger than in pure solvent of MEK. The influence of solvent upon the polymer-polymer interactions also comes from the interaction parameter term Δb, developed from modified Krigbaum and Wall theory. If PVC/PVAc blends with the weight ratio of 1/1 was dissolved in THF or DMF, Δb<0. On the contrary, if PVC/PVAc blends with the same weight ratio was dissolved in MEK, Δb>0. These experimental results show that the compatibility of PVC/PVAc blends is greatly associated with the solvent from which polymer mixtures were cast. The agreement of these results with differential scanning calorimetry measurements of PVC/PVAc blends casting from different solvents is good.     

Suspension polymerization of vinyl chloride and the processibility of poly(vinyl chloride)

The most important technological procedure in the production of PVC is the suspension polymerization of vinyl chloride, as processibility of the polymer may be influenced to a considerable extent by the choice of polymerization conditions. Structure heterogeneities in PVC powders manifest themselves in plasticized PVC by the occurrence of “fish eye” particles. This review concerns the formation and properties of these particles and discusses the causes of their difficult processibility. Also, the relation between polymerization process and PVC dehydrochlorination is discussed and a new mechanism of its initiation based on the reactivity of cisoid enone structures is proposed. These structures catalyze elimination of hydrogen chloride from regular units of PVC by an interchain enzyme-like mechanism giving rise to chloroallyl structures.     

用DSC研究线形多嵌段聚氨酯与聚氯乙烯、氯化聚氯乙烯共混相容性

用示差扫描量热法（DSC）研究了线形多嵌段聚氨酯（PU）与聚氯乙烯（PVC）、氯化聚氯乙烯（CPVC）共混相容性，说明了PU／VC、PU／CPVC的相容是由于共混物中形成了新的氢键的缘故．聚酯型聚氨酯与PVC、CPVC的相容性要好子聚酸型聚氨酯，CPVC与PU的相容性又要好于PVC．聚氨酯中硬段的引入不利于PU／PVC、PU／CPVC的相容性．     

Gas chromatographic determination of tetramethylsuccinonitrile in poly(vinyl chloride) products in contact with food

A method is described for the determination of tetramethylsuccinonitrile (TMSN) in poly(vinyl chloride) (PVC) products in contact with food. TMSN was extracted from PVC with dichloromethane, steam distilled, extracted from the distillate with dichloromethane, then determined with a gas chromatograph equipped with a nitrogen-phosphorus detector and a 6-ft. glass column packed with Chromosorb W coated with 5% Thermon 1000 plus 0.5% phosphoric acid. Recoveries between 98.3 and 100.6% were obtained in the range of 0.5-12.5 ppm of TMSN by the use of nitrobenzene as an internal standard. The detection limit was 0.05 ppm of TMSN in 1 g of PVC products. The highest residue to TMSN found in PVC products in contact with food was 13.9 ppm.     

Mechanism of decoloration by solvent of thermally degraded poly(vinyl chloride)

The mechanism of decoloration of thermally degraded poly(vinyl chloride (PVC)) by solvents has been investigated systematically. The main results obtained are as follows. Good solvents for PVC, especially tetrahydrofuran, methyl ethyl ketone, and dioxane are effective for decoloration. The solvent peroxide which is formed by autoxidation of solvent contributes to decoloration. The number of double bonds in degraded PVC decreases as the decoloration proceeds and at the same time the solvent peroxide existing in solvent is consumed. Moreover, the existence of solvent fragments in decolored PVC is recognized. From these results, it is most reasonable to conclude that the decoloration mechanism is as follows: the solvent partially is changed to a solvent peroxide by autoxidation, and the solvent peroxide reacts with polyene double bonds of degraded PVC and breaks down conjugated double bonds, and consequently degraded PVC is decolored.     

Structure and properties of poly(vinyl chloride)/graphene nanocomposites

The goal of the paper was to investigate the influence of graphene (GN) on properties and structure of suspensive poly(vinyl chloride) (PVC). PVC/GN nanocomposites were obtained by the solvent evaporation method, and their structures were evaluated using optical microscopy, SEM, FT-IR, XRD and Raman spectroscopy methods. Thermal properties of the obtained materials were studied by TGA. Electrical properties and swelling behaviour were also determined.The microscopic observations confirm a uniform distribution of graphene in the PVC matrix. The investigations carried out indicated an effect of graphene on a decrease in resistivity to a value which enabled to include the PVC/GN nanocomposites into anti-static materials group. On the basis of swelling studies, it has been found that the PVC/GN nanocomposites have a higher chemical resistance against acetone while compared to pure poly(vinyl chloride). The properties of the obtained materials depend significantly on content and dispersion level of graphene in the PVC matrix. An impact of GN on the acceleration of the PVC degradation process was found.     

Determination of adipate plasticizers in poly(vinyl chloride) by microwave-assisted extraction

A new method based on the application of microwave radiation to the extraction of adipate plasticizers from poly(vinyl chloride) PVC plastics is described. The experimental conditions for microwave-assisted extraction (i.e. extracting solvent, temperature, time and microwave power) were evaluated in terms of recovery. The optimisation was carried out with pastes of PVC plastified with di-2-ethylhexyl adipate, and extracts were measured by gas chromatography with flame ionization detection. Six different adipate plasticizers were studied, and microwave-assisted extraction was compared with supercritical fluid extraction for the extraction of adipates and phthalates from PVC matrices. It has been observed that the microwave-assisted extraction parameters evaluated are tightly interconnected. It has been shown that the efficiency of microwave-assisted extraction depends on the kind of solvent, the temperature achieved and the heating time. Moreover, the final temperature reached depends on the microwave power, the number of vessels and the irradiation time. On the other hand, microwave-assisted extraction provides higher recovery values than supercritical fluid extraction for both phthalate and adipate plasticizers.     

Influence of physical-chemical interactions on the thermal stability and surface properties of poly(vinyl chloride)-b-poly(hydroxypropyl acrylate)-b-poly(vinyl chloride) block copolymers

The synthesis of poly(vinyl chloride) (PVC) homopolymers and poly(vinyl chloride)-b-poly(hydroxypropyl acrylate)-b-poly(vinyl chloride) (PVC-b-PHPA-b-PVC) block copolymers via a single electron - degenerative transfer mediated living radical polymerisation was carried out on a pilot scale in industrial facilities. The thermal stability of the products was assessed conductimetrically. The block copolymers, that contained a low content of PHPA (below 12 wt.%), showed thermal stability that was approximately three times greater than that of conventional PVC. Inverse gas chromatography study of the copolymers surface showed that there was a decrease in the dispersive component and greater Lewis acidity and basicity constants were observed relative to those of PVC. The thermal stabilisation of PVC when in the presence of PHPA is explained by the interactions between its functional groups and the structures formed during the thermal degradation. The thermal stability and the surface properties of PVC-b-PHPA-b-PVC were strongly dependent on the molecular weight of the block copolymer. Lewis acid-base interaction parameters were determined and are interpreted as evidence of the PVC-b-PHPA-b-PVC compatibilising function in PVC-wood flour composites.     

Investigations on poly(vinyl chloride). II. Pyrolysis of chlorinated polybutadienes as model compounds for poly(vinyl chloride)

The pyrolysis of chlorinated polybutadienes (CPB) was investigated by using a pyrolysis gas chromatograph. CPB corresponds to poly(vinyl chloride) (PVC) constructed with head–head and tail–tail linkages of the vinyl chloride unit. Benzene, toluene, ethyl-benzene, o-xylene, styrene, vinyltoluene, chlorobenzenes, naphthalene, and methylnaphthalenes were detected in the pyrolysis products from CPB above 300°C, and no hydrocarbons could be detected at 200°C. The pyrolysis products from CPB were similar to those from PVC and new products could not be detected. Lower aliphatics, toluene, ethylbenzene, o-xylene, chlorobenzenes, and methylnaphthalenes were released more easily from pyrolysis of CPB than from PVC; amounts of benzene, styrene, and naphthalene formed were small. These results support the conclusion that recombination of chlorine atoms with the double bonds in the polyene chain takes place and that scission of the main chain may depend on the location of methylene groups isolated along the polyene chain during the thermal decomposition of PVC.     

Structure of chlorinated poly(vinyl chloride). V. Molecular parameters of chlorinated poly(vinyl chloride)

The molecular parameters of samples of chlorinated poly(vinyl chloride) (CPVC) and chlorinated β,β-dideuterated poly(vinyl chloride) (β,β-d₂-CPVC) were determined by gel permeation chromatography (GPC), light scattering, osmometry, and viscometry. Comparison of GPC, light scattering, osmometric, and viscometric data resulted in a discussion of the possibility of degradation and the causes of changes in the solution properties in chlorination of PVC and ββ-dideuterated poly(vinyl chloride) (ββ-d₂-PVC). The results obtained are discussed in relation to the mechanism of chlorination of PVC.     

High-temperature pyrolysis of poly(vinyl chloride): Gas chromatographic-mass spectrometric analysis of the pyrolysis products from PVC resin and plastisols

A pyrolysis–gas chromatographic–mass spectrometric technique for analyzing the pyrolysis products from polymers in an inert atmosphere is described. Initial studies encompassing the pyrolysis of poly(vinyl chloride) homopolymer and a series of PVC plastisols (based on o-phthalate esters) have provided a complete qualitative and semi-quantitative analysis of the pyrolysis products from these materials. PVC resin yields a series of aliphatic and aromatic hydrocarbons when pyrolyzed at 600°C; the amount of aromatic products is greater than the amount of aliphatic products. Benzene is the major organic degradation product. A typical PVC plastisol [PVC/o-dioctyl phthalate (100/60)] yields, upon pyrolysis, products that are characteristic of both the PVC matrix and the phthalate plasticizer. The pyrolysis products from the plasticizer dilute those from the PVC portion of the plastisol and are, in turn, the major degradation products. There are no degradation products resulting from an interaction of the PVC with the plastisol. The pyrograms resulting from pyrolysis of the various plastisols of PVC can be used for purposes of “fingerprinting.” Identification of the major peaks in a typical plastisol pyrogram provides information leading to a precise identification of the plasticizer. The pyrolysis data from this study were related to a special case of flammability and toxicity.     

Investigations on poly(vinyl chloride). IV. Effects of metal chlorides on the thermal decomposition of poly(vinyl chloride)

The effects of various metal oxides upon the thermal decomposition of poly(vinyl chloride) (PVC) were previously reported. In this work, 23 metal chlorides were investigated to determine their effects on the thermal decomposition of PVC by pyrolysis–gas chromatography at 500°C. Each metal chloride exhibits influences on the course of thermal decomposition of PVC almost similar to the corresponding metal oxide except for a few elements; the metal chlorides from acidic metal oxides accelerate the thermal decomposition of PVC, but the metal chlorides from basic metal oxides do not. On comparing the effects of metal oxides and metal chlorides on the thermal decomposition of PVC, most metal chlorides were found to accelerate the thermal decomposition of PVC more than the corresponding metal oxides, owing to ease of addition of the chlorine atoms released from metal chloride to the dehydrochlorinated chains. It is concluded from these results that the thermal decomposition of PVC containing metal salts is markedly influenced by the ease with which chlorine atoms are released from the corresponding metal chloride.     

用FTIR研究线形多嵌段聚氨酯与聚氯乙烯、氯化聚氯乙烯共混相容性

用溶液法得到线形多嵌段聚氨酯（PU）与聚氯乙烯（PV）、氯化聚氯乙烯（CPVC）的共混物。用FTIR研究PU/PVC、PU／CPVC共混物的相容性，发现PVC、CPVC的加入破坏了PU中原来的氢键，并且PU中的炭基（C=0）与PVC、CPVC中的α－H形成了新的氢键，因而说明了PU／PVC、PU／CPVC共混物具有良好的相容性。     

溶剂对聚氯乙烯-聚乙二醇-KOH体系脱氯行为的影响

废旧塑料的回收利用是当今研究的热点之一.据报道,2007年中国聚氯乙烯(PVC)产量高达960万吨[1],如何合理利用相应产生的废旧PVC是一个十分重要的课题.     

Graft polymers from poly(vinyl chloride) and chlorinated rubber

Graft polymers from poly(vinyl chloride) (PVC) and chlorinated rubber (CIR) with side chains of poly(methyl methacrylate) (PMMA), poly(methyl acrylate) (PMA), or poly(ethyl methacrylate) (PEMA) were synthesized. For this purpose, a vinyl monomer was polymerized in the presence of small quantities of PVC or CIR with benzoyl peroxide as catalyst. The graft polymers were separated from both homopolymers by precipitation with methanol from methyl ethyl ketone solutions of the reaction products and the grafting efficiency was calculated. The graft polymers were characterized by infrared spectra, elemental analysis, NMR, and osmometric or light-scattering determinations. From the results it is concluded that the PVC or CIR molecules contain side chains of PMMA, PMA, or PEMA. The graft polymers showed higher molecular weights, and the values of second virial coefficient for these polymers were much different from those of the starting polymers.     

Synthesis of adjustable poly(vinyl chloride) networks

2-Mercaptobenzyl alcohol and 4-mercaptobenzyl alcohol were synthesized in good yields starting form thiosalicylic acid and p-toluenesulfonic acid, respectively. Poly(vinyl chloride) (PVC) reacts selectively with the thiol group of these bifunctional compounds leading to modified PVC with free hydroxy groups. In a second step the polymer chains can be partially crosslinked by reaction with hexamethylene diisocyanate. According to the degree of PVC modification, the network density of the resulting elastomers is freely adjustable.     

Effects of plasticizers on novel electromechanical actuations with different poly(vinyl chloride) gels

Four different plasticizers were applied to make different poly(vinyl chloride) (PVC) gels, poly(vinyl chloride)‐bis(2‐ethylhexyl)phthalate (PVC‐DOP), poly(vinyl chloride)‐di‐n‐butylphthalate, poly(vinyl chloride)‐bis(2‐ethylhexyl)adipate, and poly(vinyl chloride)‐tris(2‐ethylhexyl)trimellitate. In our previous work, we reported that PVC‐DOP gel exhibits novel and reversible deformations of creeping and jointlike bending induced by direct current electric fields. In this article, we scrutinize the effects of plasticizers on electromechanical actuations, that is, reversible creeping and bending actuation with four of the different aforementioned gels. We measured the relative creeping distance, creeping area, creeping velocity, current observed, and bending angle as a function of applied electric fields for different PVC gels and found significant differences among them. To explain these variations, we compared the utility of plasticizers on the basis of the properties of different PVC gels, such as plasticizer‐retention ability, bending modulus, elongation at break, and the dielectric constant. The mentioned properties of the PVC gels played vital roles on their electromechanical actuations. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 2119–2127, 2003