Radiation-induced grafting of styrene onto ultra-high molecular weight polyethylene powder and subsequent film fabrication for application as polymer electrolyte membranes: I. Influence of grafting conditions

Ultra-high molecular weight polyethylene (UHMWPE) powder was irradiated by gamma rays using a ⁶⁰Co source. Simultaneous and pre-irradiation grafting was performed in air and in inert atmosphere at room temperature. The monomer selected for grafting was styrene, since the styrene-grafted UHMWPE could be readily post-sulfonated to afford proton exchange membranes (PEMs). The effect of absorbed radiation dose and monomer concentration in methanol on the degree of grafting (DG) is discussed. It was found that the DG increases linearly with increase in the absorbed dose, grafting time and monomer concentration, reaching a maximum at a certain level. The order of rate dependence of grafting on monomer concentration was found to be 2.32. Furthermore, the apparent activation energy, calculated by plotting the Arrhenius curve, was 11.5 kJ/mole. Lower activation energy and high rate dependence on monomer concentration shows the facilitation of grafting onto powder substrate compared with film. The particle size of UHMWPE powder was measured before and after grafting and found to increase linearly with increase in level of grafting. FTIR-ATR analysis confirmed the styrene grafting. The grafted UHMWPE powder was then fabricated into film and post-sulfonated using chlorosulfonic acid for the purposes of evaluating the products as inexpensive PEM materials for fuel cells. The relationship of DG with degree of substitution (DS) of styrene per UHMWPE repeat unit and ion exchange capacity (IEC) is also presented.     

Positron annihilation lifetime spectroscopy study of polyvinylpyrrolidone-added polyvinylidene fluoride membranes: Investigation of free volume and permeation relationships

Polyvinylidene fluoride (PVDF) membranes were prepared via the phase inversion method from casting solutions containing PVDF, dimethylformamide (DMF), and polyvinylpyrrolidone (PVP) as pore former. PVP was used in the casting solution in a range of 0–5 wt % and extracted. The effect on membranes of using PVP in the casting process was analyzed by X-ray diffraction, differential scanning calorimetry, scanning electron microscopy, viscosity, and water permeability techniques. With an increase of PVP from 0 to 5 wt %, the PVDF casting solution viscosities increased from 858 to 1148 cP; the resulting PVDF membrane thickness increased; and the crystallinity of PVDF membranes decreased from 40.0 to 33.3%, which indicates that the addition of PVP inhibits the degree of crystallization in the PVDF membranes. SEM results revealed the shape and size of macropores in the membranes; these macropores changed after PVP addition to the casting solutions. The impact of structural changes on free-volume properties was evaluated using positron annihilation lifetime spectroscopy (PALS) studies. PALS analysis indicated no effect on the average radius (~3.4 Å) of membrane free-volume holes from the addition of PVP to the casting solution. However, the percentage of o-Ps pick-off annihilation intensity, I₃, increased from 1.7 to 5.1% with increased PVP content. Further, increasing the PVP content from 0.5 to 5% resulted in an increased final pure water permeability flux. For instance, the 210 min flux for a 14% PVDF + 0.5% PVP membrane was found to be 3.3 times greater than a control membrane having the same PVDF concentration. © 2020 Wiley Periodicals, Inc. J. Polym. Sci. 2020 , 58, 589–598     

Preparation of poly(vinylpyrrolidone)-protected Prussian blue nanoparticles-modified electrode and its electrocatalytic reduction for hemoglobin

In this paper, a novel modified electrode was developed by using highly dispersed Prussian blue (PB) nanoparticles protected by poly(vinylpyrrolidone) (PVP). The size of the nanoparticles was controlled through adjusting the feed ratio of PVP/Fe²⁺. Physical characteristics of the nanocomposite were studied by transmission electron microscopy (TEM), UV-vis, IR spectroscopy, and X-ray powder diffraction (XRPD) analysis. The electrocatalytic reduction of hemoglobin (Hb) at PVP-protected PB nanoparticles (PVP/PB NPs)-modified electrode had been investigated. In addition, the size effects and biocompatibility of PVP/PB NPs for the electrochemistry of Hb were also observed. Experimental results indicated that the reduction peak currents of Hb were linear with its concentrations over the range from 1.0 × 10⁻⁷ to 1.2 × 10⁻⁵ mol/L and the calculated detection limit (S/N = 3) was 4.0 × 10⁻⁸ mol/L.     

Low-temperature fluorination of fluoro-containing polymers: EPR studies of polyvinylidenefluoride and the copolymer of tetrafluoroethylene with ethylene

The direct fluorination of polyvinylidenefluoride (PVDF) and the copolymer of tetrafluoroethylene with ethylene (CTE) was studied at 35-300 K. The dependence of radical formation on temperature and reaction time was obtained by use of electron paramagnetic resonance (EPR) spectroscopy. Primary alkyl radicals formed as a result of the reaction of fluorine abstracting a hydrogen from the polymer were detected at 35 K. These radicals rapidly react with molecular oxygen producing long-lived (∼48 h at 300 K) peroxy radicals. The peroxy radicals when subjected to UV-irradiation (λ < 280 nm) give rise to other radicals that are not stable at T > 77 K. The concentration of the radicals produced during fluorination of PVDF at 77-200 K is one order of magnitude less than that formed from CTE under similar conditions. A mechanism based on the abstraction of the H and the energies of the C-H bonds is given. Density functional theory was used to predict the structures and EPR parameters for a number of fluorinated radicals to explain the observed spectra. The FOO radical was detected at low temperatures.     

Optimization strategies for radiation induced grafting of 4-vinylpyridine onto poly(ethylene-co-tetraflouroethene) film using Box-Behnken design

The radiation induced grafting of 4-vinylpyridine (4-VP) onto poly(ethylene-co-tetrafluoroethene) (ETFE) was optimized using the Box-Behnken factorial design available in the response surface method (RSM). The optimized grafting parameters; absorbed dose, monomer concentration, grafting time and reaction temperature were varied in four levels to quantify their effect on the grafting yield (GY). The validity of the statistical model was supported by the small deviation between the predicted (GY=61%) and experimental (GY=57%) values. The optimum conditions for enhancing GY were determined at the following values: monomer concentration of 48 vol%, absorbed dose of 64 kGy, reaction time of 4 h and temperature of 68 °C. A comparison was made between the optimization model developed for the present grafting system and that for grafting of 1-vinylimidazole (1-VIm) onto ETFE to confirm the validly and reliability of the Box-Behnken for the optimization of various radiation induced grafting reactions. Fourier transform infrared (FTIR), thermogravimetric analysis (TGA) and X-ray diffraction (XRD) were used to investigate the properties of the obtained films and provide evidence for grafting.     

Synthesis and characterization of PVP/AAc copolymer hydrogel and its applications in the removal of heavy metals from aqueous solution

Chelating poly(vinylpyrrolidone/acrylic acid) (PVP/AAc) copolymer hydrogels were prepared by radiation-induced copolymerization. The effects of preparation parameters such as PVP content in the hydrogel and irradiation dose on the swelling behavior of the hydrogel were studied. The pH dependent swelling was investigated. The thermal stability of the prepared hydrogel and the metal chelated ones was characterized by TGA. The removal of Fe(III), Cu(II), and Mn(II) from aqueous solution by the prepared PVP/AAc chelating hydrogel was examined by batch equilibration technique. The influence of treatment time, pH, and the initial feed concentration on the amount of the metal ions removed was studied. The results show that the removal of the metal ion followed the following order: Fe(III) > Cu(II) > Mn(II). The amounts of the removed metal ions increased with treatment time and pH of the medium. To re-use the hydrogel, the metal ions were stripped by using 2 N HCl.     

Photochemical stability of poly(vinyl pyrrolidone) in the presence of collagen

The photochemical stability of poly(vinyl pyrrolidone) (PVP) in the presence of 1%, 3% and 5% of collagen has been studied by UV-vis spectroscopy, Fourier transform infrared spectroscopy (FTIR), thermogravimetry analysis (TG) and derivative thermogravimetry (DTG). Surface properties have been studied by contact angle measurements. PVP samples and samples containing 1%, 3% and 5% of collagen were irradiated with UV light of wavelength λ = 254 nm in air for up to 24 h. The amount of gel created during UV irradiation was estimated.PVP in the presence of 1%, 3% and 5% of collagen is less stable both thermally and photochemically. Collagen enhances photochemical processes leading to crosslinking of PVP. The contact angle measurements and values of surface free energy showed that the wettability of PVP films was changed by the addition of collagen and by UV irradiation. The increase of polarity of samples indicates an efficient photooxidation on the surface upon UV irradiation.     

Separation of casein micelles from whey proteins by high shear microfiltration of skim milk using rotating ceramic membranes and organic membranes in a rotating disk module

This paper investigates the microfiltration of skim milk in order to separate caseins micelles from two whey proteins, α-lactalbumin (α-La) and β-lactoglobulin (β-Lg), using a modified dynamic filtration pilot (MSD) consisting in 6 ceramic 9-cm diameter membrane disks of 0.2 μm pores, rotating around a shaft inside cylindrical housing. A comparison was made with another dynamic filtration module consisting in a disk rotating near a fixed PVDF 15.5 cm diameter membrane with 0.15 μm pores. Maximum permeate fluxes were 120 L h⁻¹ m⁻² with the MSD module at 1930 rpm and at 40 °C, and 210 L h⁻¹ m⁻² at 2500 rpm and 45 °C, with the rotating disk module. Casein rejection was around 99% at high speed for both membranes. α-La transmission decreased with increasing transmembrane pressure (TMP) from 75% to 60% for ceramic membranes and from 25% to 10% for the PVDF one. β-Lg transmissions were lower, ranging from 23% to 15% for ceramic membranes and from 20% to 5% for the PVDF one. In a concentration test with the PVDF membrane at 2000 rpm, the flux decayed from 200 L h⁻¹ m⁻² at initial concentration to 80 L h⁻¹ m⁻² at VRR = 3.2 and 22.1% of the initial α-La mass was recovered in the permeate, against 8.1% for β-Lg. Permeate fluxes in the mass transfer limited regime (J_lim) of the MSD and rotating disk module operated at various speeds were well correlated by the equation J_lim = 17.13 V_av where V_av denoted the disk azimuthal velocity averaged over the membrane area. Measurements of J_lim, taken from Ref. [G. Samuelsson, P. Dejlmek, G. Tragardh, M. Paulsson, Minimizing whey protein retention in crossflow microfiltration of skim milk. Int. Dairy J. 7 (1997) 237–242] during MF of skim milk using tubular ceramic membranes at velocities from 1.5 to 8 m s⁻¹ with permeate co-current recirculation were found to obey the same correlation.     

Synthesis and electropolymerization of 5,12-dihydrothieno[3′,4′:2,3][1,4]dioxocino[6,7-b]quinoxaline and its electrochromic properties

Synthesis of a new thiophene-based monomer; 5,12-dihydrothieno[3′,4′:2,3][1,4]dioxocino[6,7-b]quinoxaline (DDQ), was realized. The chemical structure of the monomer was characterized by ¹H NMR, FTIR and mass spectroscopy techniques. Electrochemical polymerization of DDQ and characterization of the resulting polymer [P(DDQ)] was performed. Moreover, the spectroelectrochemical and electrochromic properties of the polymer film were investigated. P(DDQ) has a low oxidation potential (0.9 V) and low band gap (1.73 eV) compared to polythiophene. In addition, dual-type polymer electrochromic device (ECD) based on P(DDQ) with poly(3,4-ethylenedioxythiophene) (PEDOT) was constructed. Spectroelectrochemistry, electrochromic switching, stability and open-circuit stability of the device were studied. It was observed that polymer have good switching time, reasonable contrast and optical memory.     

Discrimination and simultaneous determination of hydroquinone and catechol by tunable polymerization of imidazolium-based ionic liquid on multi-walled carbon nanotube surfaces

Tunable polymerization of ionic liquid on the surfaces of multi-walled carbon nanotubes (MWCNTs) was achieved by a mild thermal-initiation-free radical reaction of 3-ethy-1-vinylimidazolium tetrafluoroborate in the presence of MWCNTs. Successful modification of polymeric ionic liquid (PIL) on MWCNTs surfaces (PIL-MWCNTs) was demonstrated by scanning electron microscopy, transmission electron microscopy, Fourier transform infrared spectroscopy, thermogravimetric analysis and X-ray photoelectron spectroscopy. The resulting PIL-MWCNTs possessed unique features of high dispersity in aqueous solution and tunable thickness of PIL layer, due to positive imidazole groups along PIL chains and controllable ionic liquid polymerization by tuning the ratio of precursor. Based on cation-π interaction between the positive imidazole groups on PIL-MWCNTs surface and hydroquinone (HQ) or catechol (CC), excellent discrimination ability toward HQ and CC and improved simultaneous detection performance were achieved. The linear range for HQ and CC were 1.0 × 10⁻⁶ to 5.0 × 10⁻⁴ M and 1.0 × 10⁻⁶ to 4.0 × 10⁻⁴ M, respectively. The detection limit for HQ was 4.0 × 10⁻⁷ M and for CC 1.7 × 10⁻⁷ M (S/N = 3), correspondingly.     

Studies on the atom transfer radical polymerization of a maleimide AB* monomer and modification of the halogen end groups

The atom transfer radical polymerization (ATRP) of an AB* monomer, N-(4-α-bromobutyryloxy phenyl)maleimide (BBPMI), was conducted using the complex of CuBr/2,2′-bipyridine as catalyst. The study of kinetics of polymerization and the growth behavior of macromolecules show that the polymerization proceeds rapidly in first 1 h and then slows down. The decrease in the rate of polymerization is ascribed to the poor reactivity of maleimide radicals from A* to initiate the polymerization of maleimide double bonds. The molecular weight of the resulting polymer also increases with the dosage of catalyst. The coincidence of molecular weight determined by hydrogen proton nuclear magnetic resonance spectroscopy (¹H NMR) and gel permeation chromatography (GPC) proves that the resulting polymer is of linear structure, which is further verified by ¹³C NMR measurement and high performance liquid chromatography (HPLC) analysis of the hydrolysate of the resulting polymer. The stabilization modification of the halogen end groups of the resulting polymer by free-radical chain transfer reaction was attempted under ATRP condition. Isopropyl benzene was employed as the chain transfer agent. Indeed, the modified polymer with carbon-bromine bonds conversion of 40.7% shows enhanced thermal stability. The initial weight loss temperature has been increased from 193 to 243 °C. On the other hand, the atom transfer radical copolymerization of BBPMI with styrene resulted in the formation of hyperbranched polymer.     

Spectroscopic, thermal, magnetic and structural characterization of K3VF6 prepared at room temperature

A straight forward room-temperature synthesis of V(III) containing complex fluoride K₃VF₆, using KF and vanadium(III) acetylacetonate is reported. The pale green colored powder was characterized by chemical analysis, powder X-ray diffraction; diffuse reflectance spectroscopy, infrared spectroscopy, Raman spectroscopy, differential scanning calorimetry, scanning electron microscopy, photoluminescence spectroscopy, magnetic susceptibility measurements and photoluminescence spectroscopy. The powder X-ray diffraction pattern was fitted in P2₁/n space group (monoclinic) with a = 12.106 (1) Å, b = 17.685 (0) Å, c = 11.802 (0) Å, β = 92.23° (1). Differential scanning calorimetry showed phase transitions, occurring at 158 °C and 190 °C. In the FT-IR spectrum, characteristic band for the VF₆³⁻ group was observed at 508 cm⁻¹. The bands observed in the 335-361 cm⁻¹ region and at 504 cm⁻¹ in the room temperature Raman spectrum of K₃VF₆ corresponded to the F_2g and A_1g modes, respectively. The ratio of the frequencies (F_2g/A_1g) observed in the diffuse reflectance spectrum was fitted on the Tanabe-Sugano diagram to determine the Racah parameter B value of 712 cm⁻¹. Magnetic ordering was not observed down to the lowest measured temperature of 5 K.     

A novel sandwiched membrane as polymer electrolyte for application in lithium-ion battery

A novel kind of sandwiched polymer membrane was prepared, which consists of two outer layers of electrospun poly(vinyl difluoride) (PVDF) fibrous films and one inner layer of poly(methyl methacrylate) (PMMA) film. Its characteristics were investigated by scanning electron microscopy and X-ray diffraction. The membrane can easily absorb non-aqueous electrolyte to form gelled polymer electrolytes (GPEs). The resulting gelled polymer electrolytes had a high ionic conductivity up to 1.93 × 10⁻³ S cm⁻¹ at room temperature, and exhibited a high electrochemical stability potential of 4.5 V (vs. Li/Li⁺). It is of great potential application in polymer lithium-ion batteries.     

Albumin molecularly imprinted polymer with high template affinity — Prepared by systematic optimization in mixed organic/aqueous media

An approach using systematic optimization for the formation of an albumin molecularly imprinted polymer (MIP), able to separate albumin from proteins in solution, has been prepared by imprinting albumin using a copolymer comprising 3-dimethylaminopropyl methacrylate and tetraethylene glycol dimethacrylate in a mole ratio of 1 to 8. Cytochrome c, lysozyme and myoglobin were used in competitive re-binding experiments to compete with the polymer's native template with all protein species present at 0.0004 g mL^− 1. The effects of: monomer to crosslinker mole ratio, polymerization temperature and time were investigated. It was found that the addition of water 6.04%, into the pre-polymerization albumin-monomer complex enhanced the adsorption capacity and selectivity of the resulting MIP from 2.18 × 10^− 3 to 6.02 × 10^− 3 g g-MIP^− 1 and 83.5% to 98.7%, respectively. These results also showed that the MIP possessed high selectivity and adsorption capacity with respect to albumin in comparison with interfering species also present in solution. Polymerization temperature, time and the water content of the pre-polymerization mixture were all shown to have significant effects on the resulting albumin-MIP's performance. However, their influence on the polymer's affinity for the potentially interfering species was negligible. Additionally, higher polymerization temperatures (> 38 °C) and extended polymerization times (> 60 h) increased monomer conversion as determined by HPLC, but decreased the selectivity and adsorption capacity of the MIP. An optimized MIP, with very high selectivity and 6.37 × 10^− 3 g g-MIP^− 1 template re-adsorption capacity was obtained using the following polymerization conditions: 0.125 mole ratio of monomer to crosslinker, 6.04 wt.% water content with respect to the mass of the monomer complex, 60 h polymerization time at 38 °C, and with 0.47% albumin in the pre-polymerization monomer complex. Finally, the functions of polymerization temperature, time and the significance of the water content in the albumin-monomer complex are also discussed.     

Effect of monomer molecular flow on electrode surface on the structure of poly(α-tetrathiophene) obtained by anodic polymerization

Different structures have been found for poly(α-tetrathiophene) [poly(α-4TF)] electrosynthesized on Pt by anodic oxidation of 1.0 mM monomer solutions in media such as 45:35:20 (v/v/v) acetonitrile/THF/DMF, 45:35:20 (v/v/v) acetonitrile/ethanol/DMF and 72:28 (v/v) acetonitrile/DMF containing 0.1 M LiClO₄; as well as 72:28 (v/v) acetonitrile/DMF with 0.1 M NaClO₃, under dynamic and static conditions at 25 °C. In all cases the polymer was generated by chronoamperometry at 1.000 V vs. Ag∣AgCl, corresponding to the first oxidation peak detected by cyclic voltammetry. Uniform, adherent, insoluble and black polymer films were obtained under these conditions. The resulting structures have been elucidated by combining the information of their IR spectrum, n_ox-value and doping level of the counterion. The degree of crosslinking of every polymer has been quantified and related to the molecular flow of monomer on the Pt electrode. A monomer concentration flow between 4 × 10⁻⁶ and 5 × 10⁻⁶ mmol cm⁻² s⁻¹ was determined as the limiting value below which the polymer grows with crosslinking. This value corresponds to the electropolymerization rate of α-4TF by Pt area unit at 25 °C.     

CTAB-assisted synthesis of mesoporous F-N-codoped TiO2 powders with high visible-light-driven catalytic activity and adsorption capacity

This article describes the preparation of mesoporous rod-like F-N-codoped TiO₂ powder photocatalysts with anatase phase via a sol-gel route at the temperature of 373 K, using cetyltrimethyl ammonium bromide (CTAB) as surfactant. The as-prepared photocatalysts were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS) and UV-visible diffuse reflectance spectra (UV-vis DRS). The results showed that the photocatalysts possessed a homogeneous pore diameter and a high surface area of 106.3-160.7 m³ g⁻¹. The increasing CTAB reactive concentration extended the visible-light absorption up to 600 nm. The F-N-codoped TiO₂ powders exhibited significant higher adsorption capacity for methyl orange (MO) than that of Degussa P25 and showed more than 6 times higher visible-light-induced catalytic degradation for MO than that of P25.     

Sensitive detection of clozapine using a gold electrode modified with 16-mercaptohexadecanoic acid self-assembled monolayer

Clozapine, an effective antipsychotic drug, was found generating a pair of redox peaks at about 0.33-0.4 V (versus SCE) at 16-mercaptohexadecanoic acid (i.e. MHA) self-assembled monolayer (SAM) modified gold electrode (i.e. MHA/Au) in 0.05 mol L⁻¹ Tris-HCl (pH 8.1) buffer solution. Sensitive and quantitative measurement of clozapine based on anodic peak was established under optimum conditions. The anodic peak current was linear to clozapine concentration in the range from 1 × 10⁻⁶ to 5 × 10⁻⁵ mol L⁻¹ with the detection limit of 7 × 10⁻⁹ mol L⁻¹. This method was successfully applied to the detection of clozapine in drug tablets and proved to be reliable compared with ultraviolet spectrophotometry (UV). The MHA SAM was characterized by Fourier transform infrared spectroscopy (FT-IR), X-ray photoelectron spectroscopy (XPS), contact angle goniometry, electrochemical impedance spectroscopy (EIS) and electrochemical probe.     

Preparation of PVDF/PEO-PPO-PEO blend microporous membranes for lithium ion batteries via thermally induced phase separation process

Microporous poly(vinylidene fluoride)/polyethylene oxide-co-polypropylene oxide-co-polyethylene oxide (PVDF/PEO-PPO-PEO, or PVDF/F127) blend membranes were prepared via thermally induced phase separation (TIPS) process using sulfolane as the diluent. Then they were soaked in a liquid electrolyte to form polymer electrolytes. The effects of F127 weight fraction on the morphology, crystallinity and porosity of the blend membranes were studied. It was found that both electrolyte uptake of blend membranes and ionic conductivity of corresponding polymer electrolytes increased with the increase of F127 weight fraction. The maximum ionic conductivity was found to reach 2.94 ± 0.02 × 10⁻³ S/cm at 20 °C. Electrochemical stability window was stable up to 4.7 V (vs. Li⁺/Li). The testing results indicated that the PVDF/F127 blend membranes prepared via TIPS process can be used as the polymer microporous matrices of polymer electrolytes for lithium ion batteries.     

Radiation-grafting of 2-hydroxyethylmethacrylate and oligo (ethylene glycol) methyl ether methacrylate onto polypropylene films by one step method

Polypropylene films were modified with 2-hydroxyethylmethacrylate (HEMA) and oligo (ethylene glycol) methyl ether methacrylate (OEGMA) using the pre-irradiation method with gamma-rays (one step method). The effect of absorbed dose from 10 to 100 kGy, temperature (50, 60, and 70 °C), monomer concentration between 12.5% and 62.5%, monomers ratio from 10% to 90% and reaction time from 5 to 50 h; on the degree of grafting was determined. The grafted samples were analyzed by FTIR-ATR, TGA, DSC, swelling, and contact angle. Grafts onto polymeric films between 3% and 109% were obtained at doses from 10 to 100 kGy and a dose rate around 7.4 kGy/h. The graft percent increased with the content in HEMA in the HEMA:OEGMA feed mixture, which indicates a lower reactivity of OEGMA compared to HEMA. The hydrogel layer grafted on the polypropylene substrate increases the hydrophilicity of the surface and also provides certain temperature-responsiveness, which may be of interest for biomedical applications.     

Study on thermal cure and heat-resistant properties of N-(3-acetylenephenyl)maleimide monomer

N-(3-acetylenephenyl)maleimide (3-APMI), was synthesized by reacting 3-aminophenylacetylene (3-APA) with maleic anhydride by the usual two-step procedure that included ring-opening addition to give maleamic acid, followed by cyclodehydration to maleimide. Structure of the monomer was confirmed by Fourier transform infrared spectroscopy (FTIR), proton nuclear magnetic resonance (¹H NMR), elemental analysis (EA) and mass spectrum (MS). Thermal cure of the monomer was investigated by differential scanning calorimetry (DSC) and FTIR, then processing parameters and cure kinetics parameters were determined. The results showed that the monomer possesses excellent reactivity, whose cure peak temperature was 197.9 °C and cure reaction was almost complete after 4 h cure at 200 °C. Thermal properties of the cured monomer were determined by dynamic mechanical analysis (DMA) and the results show that glass transition temperature (represented by onset temperature of storage modulus) is high up to 460 °C. The results of thermogravimetry analysis (TGA) reveal that the cured monomer possessed excellent thermal stability, whose 10% weight loss temperature (T_10%) is 515.6 °C and char yield at 800 °C is 59.1%. All these characteristics make the 3-APMI monomer be an ideal candidate for matrix of thermo-resistant composites.