Facile measurement of polymer film thickness ranging from nanometer to micrometer scale using atomic force microscopy

As many properties of polymer thin films critically depend on their thickness, a convenient and cost‐effective method for precise measurement of film thickness in a wide range is highly desirable. Here, we present a method which enables polymer film thickness, ranging from nanometer to micrometer scale, to be facilely determined by measuring the height of an artificially created film step on smooth substrates with atomic force microscopy (AFM). Three polymeric films (polystyrene, poly(methyl methacrylate) and poly(styrene–ethylene/butylene–styrene) films), spin‐coated on either mica or quartz substrate with thickness ranging from 5.7 nm to 4.4 µm, were employed to demonstrate the procedure and feasibility of our method. The proposed method is particularly suitable for thicker polymer films, thus complementing the traditional AFM ‘tip‐scratch’ method which is generally limited to polymer films of no more than 100 nm thickness. Copyright © 2010 John Wiley & Sons, Ltd.     

Evaluation of CP Sil 8 CB film thickness for the capillary GC determination of methyl mercury

Different commercially available CP-Sil 8 CB capillary columns have been tested with a mixed standard containing methyl mercury chloride, ethyl mercury chloride and a stable nonpolar chlorinated hydrocarbon. The aim of the study was to see whether the columns tested could be used without special pretreatments and precautions for the determination of organo-mercury compounds. The GC conditions in these determinations where similar to those conditions used for the determination of chlorinated pesticides. The best peak shapes where found using a normal packed column injector, modified with a commercially available insert for on-column injections on wide bore columns, and a 5.35 m thick stationary phase. It was concluded that this CP Sil 8 CB column gave good results although minor interactions between the organomercury compounds and the column could be seen.     

Effect of stationary phase film thickness on efficiency in capillary supercritical fluid chromatography

Fused-silica capillary columns with internal diameters of 50 μm were coated with 0.25 to 1.0 μm films of SE-54 and evaluated under supercritical fluid chromatographic conditions using carbon dioxide as mobile phase. Experimental results compared well with theoretical predictions. There was no significant difference in h_min or ū_opt for film thicknesses from 0.25 to 1.0 μm over k = 1 to 5. At a film thickness of 1.0 μm, calculations indicate that approximately 10% resolution loss would be expected for solutes with k = 1.     

The dependence of the properties of liquid crystals on the film thickness and surface quality of capillary columns

Summary Glass capillary columns were prepared from non-deactivated and deactivated glass and coated with (2-methyl-4-[trans-4-n-propyl-cyclohexylcarbonyloxy]-benzoic acid-[4-n-heptyloxy-phenylester]) as the liqud phase, in different film thicknesses. The columns were tested using substances of different structures and polarities. It was verified that the capacity factors, retention indices and selectivity significantly depend on the thickness of the liquid crystalline stationary phase film and the quality of the tube, particularly in the case of columns with thin films. Trasition temperatures (melting and clearing point) of the liquid crystal are also dependent on these two factors.Dedicated to Professor J. F. K. Huber on the occasion of the his 60th birthday.     

Open tubular columns: The influence of changing the liquid phase film thickness on column efficiency

Summary The factors characterizing the influence of the variation of the liquid phase film thickness on the mass transfer terms in the Golay equations describing the performance of open tubular columns are investigated and numerical values are given.Paper dedicated to Professor S. R. Lipsky on his sixtieth birthday.     

Effect of the thickness of the Pt film coated on a counter electrode on the performance of a dye-sensitized solar cell

The effects of the thickness and morphology of a Pt film coated on a counter electrode on the performance of a dye-sensitized solar cell (DSC) were investigated. Deposition of a Pt film ranging in thickness from 2 to 415 nm gradually decreases the sheet resistance of the counter electrode. No significant difference in the charge-transfer resistance at the electrolyte|counter electrode interface was observed for a Pt film thickness ranging from 25 to 415 nm. A high energy conversion efficiency of approximately 5% can be obtained for DSCs based on a counter electrode with a very thin Pt film of 2 nm, as well as with a 415-nm thick Pt film. These results are important for reducing production costs by reducing the required amount of expensive platinum.     

Irradiated bivalve mollusks: Use of EPR spectroscopy for identification and dosimetry

High energy radiation treatment of foodstuff for microbial control and shelf-life extension is being used in many countries. However, for consumer protection and information, the European Union has adopted the Directives 1999/2/EC and 1999/3/EC to harmonize the rules concerning the treatment and trade of irradiated foods in EU countries. Among the validated methods to detect irradiated foods the EU directives also include Electron Paramagnetic Resonance (EPR/ESR) spectroscopy.We describe herein the use of EPR for identification of four species of bivalve mollusks, i.e. brown Venus shells (Callista chione), clams (Tapes semidecussatus), mussels (Mytilus galloprovincialis) and oysters (Ostrea edulis) irradiated with ⁶⁰Co γ-rays. EPR could definitely identify irradiated seashells due to the presence of long-lived free radicals, primarily CO₂⁻, CO₃³⁻, SO₂⁻ and SO₃⁻ radical anions. The presence of other organic free radicals, believed to originate from conchiolin, a scleroprotein present in the shells, was also ascertained. The use of one of these radicals as a marker for irradiation of brown Venus shells and clams can be envisaged. We also propose a dosimetric protocol for the reconstruction of the administered dose in irradiated oysters.     

Drainage and critical thickness of foam films from aqueous solutions of mixed nonionic surfactants

The thinning and the critical thickness (of rupture or “black spots” formation) of foam films from aqueous solutions of mixed nonionic surfactants are studied under varied experimental conditions, as a function of film radius (0.05–0.15 mm), surfactant concentration (0.01–1.0 CMC) and ionic strength (0.001–0.1 M NaCl). The experimental values of the drainage coefficient (), determined from the film thickness versus time dependences, were used to calculate the theoretical values of the film critical thickness.

The real velocity of film thinning is a major factor in the process of reaching the state of kinetic instability when approaching the critical thickness (Scheludko's criterion). The classical equation used to describe the film thinning rate, proposed and named by Scheludko (1955) “Reynolds Law”, is applicable for small film radii (r < 0.05 mm). At larger radii the velocity of thinning follows the equation of Manev et al. [E.D. Manev, R. Tsekov, B. Radoev, J. Colloid Interf. Sci. 18 (1997) 769], which takes into account the effect of the film thickness local non-homogeneity.

The studied stabilizing surfactants include n-dodecyl-β-d-maltoside (β-C12G2) and hexaethyleneglycol monododecyl ether (C12E6). Along with confirming the dependences following from the theories of the critical thickness [B. Radoev, A. Scheludko, E.D. Manev, J. Colloid Interf. Sci. 95 (1983) 254] and film thinning [E.D. Manev, R. Tsekov, B. Radoev, J. Colloid Interf. Sci. 18 (1997) 769], the results of the present investigation established also certain deviations for films stabilized with mixed surfactants (β-C12G2 + C12E6). The effectiveness of the empirical equation, employing the drainage coefficient () to describe the film thinning, is emphatically proven here.     

Determination of thickness distribution and composition of thin coatings by EPMA: Application in the field of steel sheet production

A new method for the investigation of surface coatings by EPMA is presented. It is based on a physical model which takes into account the X-ray intensity depth distribution, the absorption and the electron backscattering effects at the interface between film and substrate. When combined with the concentration mapping (CM) technique, a two-dimensional film thickness distribution and the film composition can be determined simultaneously. Only bulk standards are required for this method.With some examples in the field of steel sheet production and electrogalvanizing the versatility of the method as well as its high sensitivity are pointed out. Particularly important for practical work is the applicability to almost any combinations of film and substrate materials as well as the wide thickness range from almost the total X-ray emergence depth down to the monolayer range.Dedicated to Professor Günther Tölg on the occasion of his 60th birthday     

Variation of tube diameter and film thickness of capillary columns

This paper briefly surveys three important considerations related to the tube diameter and film thickness. These are the interrelationship of these two parameters through the phase ratio, the different meanings of the term “efficiency”, and the influence of film thickness and tube diameter on sample capacity. Comparative examples are given for columns having different diameters and film thicknesses.     

The thickness and contact angle of sodium dodecyl sulfate foam films depending on the concentration of LiCl

 In the present study a detailed investigation of the thickness and contact angles of foam films prepared from sodium dodecyl sulfate as a function of LiCl concentration was carried out. Concentration of LiCl was varied in a wide range from 0.05 to 2.0 M. It was found that in the investigated system Newton black foam films are formed at LiCl concentrations higher than 1.4 M. This observation is proved by contact angle measurements and calculated values for the change of interaction free energy between common and Newton black films. Received: 6 January 1998 Accepted: 11 March 1998     

正交设计和均匀设计用于硒-金膜修饰电极制备条件的选择

硒代胱氨酸在硒 金(Se Au)膜修饰玻碳电极上产生两个灵敏的氧化还原峰:峰II(-500mV左右)和峰III(-327mV左右),以峰II的峰电流作为评价指标,采用正交设计与均匀设计相结合的方法对Se Au膜修饰电极的制备条件进行优化得到最佳优化条件:底液0.1mol LKCl;沉积电位为-850mV;沉积时间为60s;SeO2浓度为8.3×10-3mol L;AuCl3浓度为8.9×10-4mol L。均匀设计的数据应用Matlab计算机软件处理。依此制备的Se Au膜修饰电极性能稳定,用于硒代胱氨酸伏安特性研究有良好的重现性。     

Effects of elevated temperatures during interruption of irradiation on Harwell Red 4034 PMMA and Kodak Biomax alanine film dosimetry systems

In the industrial setting it is not uncommon for a process interruption to occur during irradiation. In this event, dosimeters may be exposed to prolonged periods of elevated temperature without exposure to ionizing radiation. Once the process is restarted, the same dosimeters are exposed to ionizing radiation in order to achieve target dose. The goal of this experiment was to simulate a process interruption within limits and quantify the effects of a combination of factors (heat, time, and fractionation) on dosimeter response. We present an in-depth experimental study on the response of dosimeters that have been irradiated, stored for a fixed period of time at several temperatures, and then re-irradiated. This study was performed using Harwell Red 4034 polymethylmethacrylate (PMMA) and Kodak BioMax alanine film dosimeters.     

Performance of open tubular columns as a function of tube diameter and liquid phase film thickness

Summary Wall-coated, open-tubular (capillary) columns prepared from different diameter tubing, with different liquid phase film thickness, are compared with each other and with packed and support-coated open-tubular columns. The comparison is based on the variation of the phase ratio and the capacity factor, and includes column efficiency (HETP, theoretical plate number), resolution, retention time, and sample capacity. Problems associated with the evaluation of the sample capacity are outlined. The influence of temperature on column performance is discussed in detail. Finally, the possibilities of short, wide-bore open-tubular columns prepared with a thick liquid-phase film are demonstrated.Parts of this paper were presented at the 35th Pittsburgh Conference on Analytical Chemistry and Applied Spectroscopy, Atlantic City NJ, March 5–9, 1984, and at the 20th International Symposium on Advances in Chromatography, New York NY, April 16–18, 1984.     

Effect of film thickness and supercooling on the performance of cholesteryl cinnamate liquid crystal capillary columns

Improved separations of the isomers of olefinic aliphatic insect pheromones were obtained on cholesteryl cinnamate glass capillary columns by operating in the supercooled temperature range of the liquid crystal. Capillary columns were prepared with varying film thickness of the stationary phase; choice of the correct film thickness ensured optimum retention for a wide range of compounds within the most effective temperature range of the liquid crystal. The deactivation procedures described made the liquid crystal columns suitable for separation of the geometric isomers of polar and nonpolar compounds.     

Adhesion of silicon oxide layers on poly(ethylene terephthalate). II: Effect of coating thickness on adhesive and cohesive strengths

Fragmentation tests in the uniaxial mode were performed on poly (ethylene terephthalate) (PET) films coated with a silicon oxide layer of thickness ranging from 30 to 156 nm. The coating's fragmentation process was investigated to reveal the crack onset strain and the crack density at fragmentation saturation. Adhesive strength was modeled from the Kelly-Tyson approach, including a Weibull distribution of the coating strength. The prediction was found to be independent of coating thickness, and equal to the substrate shear stress at saturation. The cohesive strength of the coating was characterized from the crack onset strain. The measured decrease in crack onset strain with coating thickness increase was modeled by means of Weibull and fracture mechanics theories, the latter providing the best predictions. © 1997 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 35 : 1463–1472, 1997     

Optimization of thin film solid phase microextraction and data deconvolution methods for accurate characterization of organic compounds in produced water

The continued rise in the extraction of unconventional oil and gas across the globe poses many questions about how to manage these relatively new waste‐streams. Produced water, the primary waste by‐product, contains a diverse number of anthropogenic additives together with the numerous hydrocarbons extracted from the well. Due to potential environmental hazards, it is critical to characterize the chemical composition of this type of waste before proper disposal or remediation/reuse. In this work, a thin film solid phase microextraction approach was developed and optimized to characterize produced water. The thin film device consisted of hydrophilic‐lipophilic balance particles embedded in polydimethylsiloxane and immobilized on a carbon mesh surface. These devices were chosen to provide broad extraction coverage and high reusability. Various parameters were evaluated to ensure reproducible results while minimizing analyte loss. This optimized protocol, consisting of a 15 min extraction followed by a short (3 s) rinsing step, enabled the reproducible analysis of produced water without any sample pretreatment. Extraction efficiency was suitable for both produced water additives and hydrocarbons. The developed approach was able to tentatively identify a total of 201 compounds from produced water samples, by using one‐dimensional gas chromatography hyphenated to mass spectrometry and data deconvolution.     

Development of a competitive lateral flow immunoassay for progesterone: influence of coating conjugates and buffer components

Several aspects of the development of competitive lateral flow immunoassays (LFIAs) are described. The quantitation of progesterone is taken as an example. The LFIA format consisted of a nitrocellulose membrane spotted with various progesterone conjugates as the test line. A mixture of primary antibody and secondary antibody adsorbed to colloidal carbon was used for signal generation. A digital scanner and dedicated software were used to quantitate the response. A reappraisal of the checkerboard titration, often used in the optimisation of immunoassays, is discussed. Surprisingly, the highest sensitivity of the LFIA format (IC₅₀ of 0.6 μg L⁻¹ progesterone in buffer) was achieved by using a high coating concentration of the analyte–protein conjugate and a high dilution of the antibody solution. Immediate addition of all reagents in LFIA was superior to premixing the components and allowing prereaction. Of several blocking agents tested bovine serum albumin was superior in performance, whereas the combination of ovalbumin and progesterone substantially influenced test results.     

Exploring the characteristics,performance, and modification of Matrimid for development of thin‐film composite and thin‐film nanocomposite reverse osmosis membranes

Reverse osmosis (RO) membrane technology is widely employed to address the demands for freshwater. In this study, fabrication and performance evaluation of customized RO membranes comprised of Matrimid and polyacrylonitrile (PAN) is carried out. While exploring adoption of slip coating procedure, the effects of various modification techniques including incorporation of TiO₂ nanoparticles and polyethylene glycol (PEG) into the skin layer as well as cross‐linking were investigated. The individual and combined effects of parameters on membrane morphology, surface characteristics and performance were also examined. Despite the distinctive characteristics of involved materials, delamination‐free composite membranes were successfully formed with an intimate contact at the interface of two layers. The results also indicated that increasing concentration of Matrimid in dope solution led to increase in membrane thickness and consequently decline in water flux. In the best case, membrane prepared using 1 wt.% Matrimid in dope exhibited water flux of 0.98 LMH and NaCl rejection of 95.7%. Also, incorporation of 3 wt.% TiO₂ nanoparticles offered membranes with improved water flux of 1.37 LMH and salt rejection of 95.8%. On the other hand, water flux and salt rejection in membranes containing 5 wt.% PEG were 1.18 LMH and 96.2%, respectively. The co‐presence of both nanoparticles and PEG provided more insights about the contributing factors in tuned membranes. Modification of skin layer by cross‐linking significantly improved salt rejection at the expense of water flux. The results are scientifically interpreted and compared to the values reported in literature.