Validation of a novel very large eddy simulation method for simulation of turbulent separated flow

The paper describes the validation of a newly developed very LES (VLES) method for the simulation of turbulent separated flow. The new VLES method is a unified simulation approach that can change seamlessly from Reynolds‐averaged Navier–Stokes to DNS depending on the numerical resolution. Four complex test cases are selected to validate the performance of the new method, that is, the flow past a square cylinder at Re = 3000 confined in a channel (with a blockage ratio of 20%), the turbulent flow over a circular cylinder at Re = 3900 as well as Re = 140,000, and a turbulent backward‐facing step flow with a thick incoming boundary layer at Re = 40,000. The simulation results are compared with available experimental, LES, and detached eddy simulation‐type results. The new VLES model performs well overall, and the predictions are satisfactory compared with previous experimental and numerical results. It is observed that the new VLES method is quite efficient for the turbulent flow simulations; that is, good predictions can be obtained using a quite coarse mesh compared with the previous LES method. Discussions of the implementation of the present VLES modeling are also conducted on the basis of the simulations of turbulent channel flow up to high Reynolds number of Re_τ = 4000. The efficiency of the present VLES modeling is also observed in the channel flow simulation. From a practical point of view, this new method has considerable potential for more complex turbulent flow simulations at relative high Reynolds numbers. Copyright © 2013 John Wiley & Sons, Ltd.     

Numerical prediction of turbulent flows using Reynolds‐averaged Navier–Stokes and large‐eddy simulation with uncertain inflow conditions

Numerous comparisons between Reynolds‐averaged Navier–Stokes (RANS) and large‐eddy simulation (LES) modeling have already been performed for a large variety of turbulent flows in the context of fully deterministic flows, that is, with fixed flow and model parameters. More recently, RANS and LES have been separately assessed in conjunction with stochastic flow and/or model parameters. The present paper performs a comparison of the RANS k ? ε model and the LES dynamic Smagorinsky model for turbulent flow in a pipe geometry subject to uncertain inflow conditions. The influence of the experimental uncertainties on the computed flow is analyzed using a non‐intrusive polynomial chaos approach for two flow configurations (with or without swirl). Measured quantities including an estimation of the measurement error are then compared with the statistical representation (mean value and variance) of their RANS and LES numerical approximations in order to check whether experiment/simulation discrepancies can be explained within the uncertainty inherent to the studied configuration. The statistics of the RANS prediction are found in poor agreement with experimental results when the flow is characterized by a strong swirl, whereas the computationally more expensive LES prediction remains statistically well inside the measurement intervals for the key flow quantities.Copyright © 2012 John Wiley & Sons, Ltd.     

Swirling-strength based large eddy simulation of turbulent flow around single square cylinder at low Reynolds numbers

In view of the fact that large scale vortices play the substantial role of momentum transport in turbulent flows, large eddy simulation(LES) is considered as a better simulation model. However, the sub-grid scale(SGS) models reported so far have not ascertained under what flow conditions the LES can lapse into the direct numerical simulation. To overcome this discrepancy, this paper develops a swirling strength based the SGS model to properly model the turbulence intermittency, with the primary characteristics that when the local swirling strength is zero, the local sub-grid viscosity will be vanished. In this paper, the model is used to investigate the flow characteristics of zero-incident incompressible turbulent flows around a single square cylinder(SC)at a low Reynolds number range Re ∈ [103, 104]. The flow characteristics investigated include the Reynolds number dependence of lift and drag coefficients, the distributions of time-spanwise averaged variables such as the sub-grid viscosity and the logarithm of Kolmogorov micro-scale to the base of 10 at Re = 2 500 and 104, the contours of spanwise and streamwise vorticity components at t = 170. It is revealed that the peak value of sub-grid viscosity ratio and its root mean square(RMS) values grow with the Reynolds number. The dissipation rate of turbulent kinetic energy is larger near the SC solid walls.The instantaneous factor of swirling strength intermittency(FSI) exhibits some laminated structure involved with vortex shedding.     

LES and RANS for Turbulent Flow over Arrays of Wall-Mounted Obstacles

Large-eddy simulation (LES) has been applied to calculate the turbulent flow over staggered wall-mounted cubes and staggered random arrays of obstacles with area density 25%, at Reynolds numbers between 5 × 10³ and 5 10⁶, based on the free stream velocity and the obstacle height. Re = 5 × 10³ data were intensively validated against direct numerical simulation (DNS) results at the same Re and experimental data obtained in a boundary layer developing over an identical roughness and at a rather higher Re. The results collectively confirm that Reynolds number dependency is very weak, principally because the surface drag is predominantly form drag and the turbulence production process is at scales comparable to the roughness element sizes. LES is thus able to simulate turbulent flow over the urban-like obstacles at high Re with grids that would be far too coarse for adequate computation of corresponding smooth-wall flows. Comparison between LES and steady Reynolds-averaged Navier-Stokes (RANS) results are included, emphasising that the latter are inadequate, especially within the canopy region.     

Properties of the hybrid RANS/LES filter

One of the most important and challenging topics in the Large Eddy Simulation of turbulent flows is the connection of the LES technique to the well known and largely used RANS approach where the Navier–Stokes equations are Reynolds averaged. The hybridation of LES and RANS is not only important for its possible practical use, (a rational use of the computational means in different zones), but also from a theoretical point of view, and one possible procedure consists of blending RANS and LES models in the transition zone. In this paper a new filtering technique based on blending filters which transitions smoothly between LES and RANS is proposed and the associated universal model for the subgrid scale stresses is derived. PACS 47.27.Eq     

Large eddy simulation of fuel injection and mixing process in a diesel engine

The large eddy simulation(LES) approach implemented in the KIVA-3V code and based on one-equation sub-grid turbulent kinetic energy model are employed for numerical computation of diesel sprays in a constant volume vessel and in a Caterpillar 3400 series diesel engine.Computational results are compared with those obtained by an RANS(RNG k-ε) model as well as with experimental data.The sensitivity of the LES results to mesh resolution is also discussed.The results show that LES generally provides flow and spray characteristics in better agreement with experimental data than RANS;and that small-scale random vortical structures of the in-cylinder turbulent spray field can be captured by LES.Furthermore,the penetrations of fuel droplets and vapors calculated by LES are larger than the RANS result,and the sub-grid turbulent kinetic energy and sub-grid turbulent viscosity provided by the LES model are evidently less than those calculated by the RANS model.Finally,it is found that the initial swirl significantly affects the spray penetration and the distribution of fuel vapor within the combustion chamber.     

VLES Modeling of Flow Over Walls with Variably-shaped Roughness by Reference to Complementary DNS

Turbulent flow over variably-shaped rough walls, characterized by either a regular or a random arrangement of axisymmetric roughness elements in an open channel flow configuration, is investigated computationally within a VLES (Very Large Eddy Simulation) framework by utilizing a volumetric forcing-based roughness model. The prime objective of the present work is to assess the roughness model’s capability to predict mean velocities and turbulent intensities in conjunction with this recently formulated hybrid LES/RANS (Reynolds-Averaged Navier-Stokes) model. The friction velocity-based Reynolds number is in the range Re_τ =?460 ? 500. A non-dimensional drag function accounting for the shape of the roughness elements is introduced and evaluated based on the results of complementary direct numerical simulations (DNS). The dynamics of the residual motion of the presently adopted VLES methodology is described by an appropriately modified elliptic-relaxation-based ζ ? f (\(\zeta =\overline {v^{2}}/k\)) RANS model.     

LES-based filter-matrix lattice Boltzmann model for simulating fully developed turbulent channel flow

In this paper, a three-dimensional filter-matrix lattice Boltzmann (FMLB) model based on large eddy simulation (LES) was verified for simulating wall-bounded turbulent flows. The Vreman subgrid-scale model was employed in the present FMLB–LES framework, which had been proved to be capable of predicting turbulent near-wall region accurately. The fully developed turbulent channel flows were performed at a friction Reynolds number Re_τ of 180. The turbulence statistics computed from the present FMLB–LES simulations, including mean stream velocity profile, Reynolds stress profile and root-mean-square velocity fluctuations greed well with the LES results of multiple-relaxation-time (MRT) LB model, and some discrepancies in comparison with those direct numerical simulation (DNS) data of Kim et al. was also observed due to the relatively low grid resolution. Moreover, to investigate the influence of grid resolution on the present LES simulation, a DNS simulation on a finer gird was also implemented by present FMLB–D3Q19 model. Comparisons of detailed computed various turbulence statistics with available benchmark data of DNS showed quite well agreement.     

Surface‐sampled simulations of turbulent flow at high Reynolds number

A new approach to turbulence simulation, based on a combination of large eddy simulation (LES) for the whole flow and an array of non–space‐filling quasi‐direct numerical simulations (QDNS), which sample the response of near‐wall turbulence to large‐scale forcing, is proposed and evaluated. The technique overcomes some of the cost limitations of turbulence simulation, since the main flow is treated with a coarse‐grid LES, with the equivalent of wall functions supplied by the near‐wall sampled QDNS. Two cases are tested, at friction Reynolds number Re_τ=4200 and 20000. The total grid point count for the first case is less than half a million and less than 2 million for the second case, with the calculations only requiring a desktop computer. A good agreement with published direct numerical simulation (DNS) is found at Re_τ=4200, both in the mean velocity profile and the streamwise velocity fluctuation statistics, which correctly show a substantial increase in near‐wall turbulence levels due to a modulation of near‐wall streaks by large‐scale structures. The trend continues at Re_τ=20000, in agreement with experiment, which represents one of the major achievements of the new approach. A number of detailed aspects of the model, including numerical resolution, LES‐QDNS coupling strategy and subgrid model are explored. A low level of grid sensitivity is demonstrated for both the QDNS and LES aspects. Since the method does not assume a law of the wall, it can in principle be applied to flows that are out of equilibrium.     

Wall modeling for implicit large-eddy simulation and immersed-interface methods

We propose and analyze a wall model based on the turbulent boundary layer equations (TBLE) for implicit large-eddy simulation (LES) of high Reynolds number wall-bounded flows in conjunction with a conservative immersed-interface method for mapping complex boundaries onto Cartesian meshes. Both implicit subgrid-scale model and immersed-interface treatment of boundaries offer high computational efficiency for complex flow configurations. The wall model operates directly on the Cartesian computational mesh without the need for a dual boundary-conforming mesh. The combination of wall model and implicit LES is investigated in detail for turbulent channel flow at friction Reynolds numbers from Re _τ  = 395 up to Re _τ =100,000 on very coarse meshes. The TBLE wall model with implicit LES gives results of better quality than current explicit LES based on eddy viscosity subgrid-scale models with similar wall models. A straightforward formulation of the wall model performs well at moderately large Reynolds numbers. A logarithmic-layer mismatch, observed only at very large Reynolds numbers, is removed by introducing a new structure-based damping function. The performance of the overall approach is assessed for two generic configurations with flow separation: the backward-facing step at Re _h = 5,000 and the periodic hill at Re _H = 10,595 and Re _H = 37,000 on very coarse meshes. The results confirm the observations made for the channel flow with respect to the good prediction quality and indicate that the combination of implicit LES, immersed-interface method, and TBLE-based wall modeling is a viable approach for simulating complex aerodynamic flows at high Reynolds numbers. They also reflect the limitations of TBLE-based wall models.     

A reformulated synthetic turbulence generation method for a zonal RANS–LES method and its application to zero-pressure gradient boundary layers

A synthetic turbulence generation (STG) method for subsonic and supersonic flows at low and moderate Reynolds numbers to provide inflow distributions of zonal Reynolds-averaged Navier–Stokes (RANS) – large-eddy simulation (LES) methods is presented. The STG method splits the LES inflow region into three planes where a local velocity signal is decomposed from the turbulent flow properties of the upstream RANS solution. Based on the wall-normal position and the local flow Reynolds number, specific length and velocity scales with different vorticity content are imposed at the inlet plane of the boundary layer. The quality of the STG method for incompressible and compressible zero-pressure gradient boundary layers is shown by comparing the zonal RANS–LES data with pure LES, pure RANS, and direct numerical simulation (DNS) solutions. The distributions of the time and spanwise wall-shear stress, Reynolds stress distributions, and two point correlations of the zonal RANS–LES simulations are smooth in the transition region and in good agreement with the pure LES and reference DNS findings. The STG approach reduces the RANS-to-LES transition length to less than four boundary-layer thicknesses.     

A hybrid RANS/LES simulation of high-Reynolds-number channel flow using additional filtering at the interface

A hybrid method combining large eddy simulation (LES) with the Reynolds-averaged Navier-Stokes (RANS) equation is used to simulate a turbulent channel flow at high Reynolds number. It is known that the mean velocity profile has a mismatch between the RANS and LES regions in hybrid simulations of a channel flow. The velocity mismatch is reproduced and its dependence on the location of the RANS/LES interface and on the type of RANS model is examined in order to better understand its properties. To remove the mismatch and to obtain better velocity profiles, additional filtering is applied to the velocity components in the wall-parallel planes near the interface. The additional filtering was previously introduced to simulate a channel flow at low Reynolds number. It is shown that the filtering is effective in reducing the mismatch even at high Reynolds number. Profiles of the velocity fluctuations of runs with and without the additional filtering are examined to help understand the reason for the mismatch. Due to the additional filtering, the wall-normal velocity fluctuation increases at the bottom of the LES region. The resulting velocity field creates the grid-scale shear stress more efficiently, and an overestimate of the velocity gradient is removed. The dependence of the velocity profile on the grid point number is also investigated. It is found that the velocity gradient in the core region is underestimated in the case of a coarse grid. Attention should be paid not only to the velocity mismatch near the interface but also to the velocity profile in the core region in hybrid simulations of a channel flow at high Reynolds number. PACS47.27.Eq; 47.27.Nz; 47.60.+i     

An eddy viscosity model with near‐wall modifications

An extended version of the isotropic k–ε model is proposed that accounts for the distinct effects of low‐Reynolds number (LRN) and wall proximity. It incorporates a near‐wall correction term to amplify the level of dissipation in nonequilibrium flow regions, thus reducing the kinetic energy and length scale magnitudes to improve prediction of adverse pressure gradient flows, involving flow separation and reattachment. The eddy viscosity formulation maintains the positivity of normal Reynolds stresses and the Schwarz' inequality for turbulent shear stresses. The model coefficients/functions preserve the anisotropic characteristics of turbulence. The model is validated against a few flow cases, yielding predictions in good agreement with the direct numerical simulation (DNS) and experimental data. Comparisons indicate that the present model is a significant improvement over the standard eddy viscosity formulation. Copyright © 2005 John Wiley & Sons, Ltd.     

Large eddy simulation of gas-particle turbulent channel flow with momentum exchange between the phases

This paper presents results of a large eddy simulation (LES) combined with Lagrangian particle tracking and a point-force approximation for the feedback effect of particles on the downward turbulent gaseous flow in a vertical channel. The LES predictions are compared with the results obtained by direct numerical simulation (DNS) of a finer computational mesh. A parametric study is conducted for particles with two response times in simulations with and without streamwise gravitational settling and elastic, binary interparticle collisions. It is shown that the classical and the dynamic Smagorinsky turbulence models adequately predict the particle-induced changes in the mean streamwise velocity and the Reynolds stresses of the carrier phase for the range of parameters studied. However, the largest discrepancies between the LES and DNS results are found in the cases of particle-laden flows. Conditional sampling of the instantaneous resolved flow fields indicates that the mechanisms by which particles directly oppose the production of momentum and vorticity of the organized fluid motions are also observed in the LES results. However, the geometric features of the near-wall quasistreamwise vortices are overestimated by the use of both turbulence models compared to the DNS predictions.     

植被层湍流的大涡模拟

研究植被层湍流的大涡模拟,发展了一个TSF（transientstructurefunction）亚格于模式,尽可能真实地处理植被湍流这种既有强剪切,又有热对流的流动．我们建立了植被湍流数据库,并进行了较为详细的分析研究．湍流统计量如平均风速剖面、雷诺应力、湍流脉动能等等,与有关观测结果作了对比,符合较好．大涡模拟计算同样发现已由现场观测到的、在强对流情况时出现的温度场斜坡型有组织结构．     

Parallel FEM LES with one-equation subgrid-scale model for incompressible flows

This article develops a parallel large-eddy simulation (LES) with a one-equation subgrid-scale (SGS) model based on the Galerkin finite element method and three-dimensional (3D) brick elements. The governing filtered Navier–Stokes equations were solved by a second-order accurate fractional-step method, which decomposed the implicit velocity–pressure coupling in incompressible flow and segregated the solution to the advection and diffusion terms. The transport equation for the SGS turbulent kinetic energy was solved to calculate the SGS processes. This FEM LES model was applied to study the turbulence of the benchmark open channel flow at a Reynolds number Re_τ = 180 (based on the friction velocity and channel height) using different model constants and grid resolutions. By comparing the turbulence statistics calculated by the current model with those obtained from direct numerical simulation (DNS) and experiments in literature, an optimum set of model constants for the current FEM LES model was established. The budgets of turbulent kinetic energy and vertical Reynolds stress were then analysed for the open channel flow. Finally, the flow structures were visualised to further reveal some important characteristics. It was demonstrated that the current model with the optimum model constants can predict well the organised structure near the wall and free surface, and can be further applied to other fundamental and engineering applications.     

A new wall-damping function for large eddy simulation employing Kolmogorov velocity scale

A new wall-damping function, based on the Kolmogorov velocity scale, for large eddy simulation (LES) is proposed, which accounts for the near-wall effect. To calculate the Kolmogorov velocity scale, u_ε, the dissipation rate of turbulent energy, ε, is needed. In LES, however, the dissipation rate is generally not solved, unlike in the Reynolds averaged Navier-Stokes (RANS) simulations, e.g., k-ε models. Although, in some previous studies, the dissipation rate of the subgrid-scale (SGS) turbulent energy, ε_SGS, is used instead of ε in calculating the Kolmogorov velocity scale, the scale obtained using such a method overly depends on the grid resolution employed and is generally inappropriate. Accordingly, the wall-damping function using the incorrect velocity scale also depends on the grid resolution and gives an inadequate wall effect. This is because ε_SGS contains only the components in the scale smaller than the grid-filter width, which obviously varies with the grid resolution employed. In this study, to overcome this problem, we propose a method for estimating the Kolmogorov velocity scale with a technique of conversion in LES, and the estimated one is utilized in the wall-damping function. The revised wall-damping function for LES is tested in channel flows and a backward-facing step flow. The results show that it yields a proper near-wall effect in all test cases which cover a wide range of grid resolution and Reynolds numbers. It is also shown that all three kinds of SGS models incorporating the present wall-damping function provide good predictions, and it is effective both in one-equation and 0-equation SGS models. These results suggest that the use of the proposed wall-damping function is a refined and versatile near-wall treatment in LES with various kinds of SGS models.     

Turbulent Couette–Taylor flows with endwall effects: A numerical benchmark

The accurate prediction of fluid flow within rotating systems has a primary role for the reliability and performance of rotating machineries. The selection of a suitable model to account for the effects of turbulence on such complex flows remains an open issue in the literature. This paper reports a numerical benchmark of different approaches available within commercial CFD solvers together with results obtained by means of in-house developed or open-source available research codes exploiting a suitable Reynolds Stress Model (RSM) closure, Large Eddy Simulation (LES) and a direct numerical simulation (DNS). The predictions are compared to the experimental data of Burin et al. (2010) in an original enclosed Couette–Taylor apparatus with endcap rings. The results are discussed in details for both the mean and turbulent fields. A particular attention has been turned to the scaling of the turbulent angular momentum G with the Reynolds number Re. By DNS, G is found to be proportional to Re^α, the exponent α = 1.9 being constant in our case for the whole range of Reynolds numbers. Most of the approaches predict quite well the good trends apart from the k–ω SST model, which provides relatively poor agreement with the experiments even for the mean tangential velocity profile. Among the RANS models, even though no approach appears to be fully satisfactory, the RSM closure offers the best overall agreement.     

Numerical study of an oscillatory turbulent flow over a flat plate

Oscillatory turbulent flow over a flat plate is studied using large eddy simulation (LES) and Reynolds-average Navier-Stokes (RANS) methods. A dynamic subgrid-scale model is employed in LES and Saffman's turbulence model is used in RANS. The flow behaviors are discussed for the accelerating and decelerating phases during the oscillating cycle. The friction force on the wall and its phase shift from laminar to turbulent regime are also investigated for different Reynolds numbers. The project supported by the Youngster Funding of Academia Sinica and by the National Natural Science Foundation of China     

Simulations of Turbulent Flow in a Plane Asymmetric Diffuser

Large-eddy simulations (LES) of a planar, asymmetric diffuser flow have been performed. The diverging angle of the inclined wall of the diffuser is chosen as 8.5°, a case for which recent experimental data are available. Reasonable agreement between the LES and the experiments is obtained. The numerical method is further validated for diffuser flow with the diffuser wall inclined at a diverging angle of 10°, which has served as a test case for a number of experimental as well as numerical studies in the literature (LES, RANS). For the present results, the subgrid-scale stresses have been closed using the dynamic Smagorinsky model. A resolution study has been performed, highlighting the disparity of the relevant temporal and spatial scales and thus the sensitivity of the simulation results to the specific numerical grids used. The effect of different Reynolds numbers of the inflowing, fully turbulent channel flow has been studied, in particular, Re _b  = 4,500, Re _b  = 9,000 and Re _b  = 20,000 with Re _b being the Reynolds number based on the bulk velocity and channel half width. The results consistently show that by increasing the Reynolds number a clear trend towards a larger separated region is evident; at least for the studied, comparably low Reynolds-number regime. It is further shown that the small separated region occurring at the diffuser throat shows the opposite behaviour as the main separation region, i.e. the flow is separating less with higher Re _b . Moreover, the influence of the Reynolds number on the internal layer occurring at the non-inclined wall described in a recent study has also been assessed. It can be concluded that this region close to the upper, straight wall, is more distinct for larger Re _b . Additionally, the influence of temporal correlations arising from the commonly used periodic turbulent channel flow as inflow condition (similar to a precursor simulation) for the diffuser is assessed.