铂/多壁碳纳米管修饰玻碳电极用于微分脉冲伏安法测定左旋多巴

采用微波辅助加热多元醇技术制备了载铂多壁碳纳米管复合材料,并将该复合材料分散在N,N′-二甲基甲酰胺溶液中得到悬浮液,取14μL悬浮液滴涂在玻碳电极表面,制备铂/多壁碳纳米管修饰电极(Pt/MWCNT′s/GCE)。循环伏安法研究了在0.05mol·L~(-1)硫酸支持电解质中,在0.30～0.70V(vs.SCE)电位范围内,左旋多巴在修饰电极上的电化学行为,结果表明:左旋多巴在Pt/MWCNT′s/GCE上于电位0.548V处可见明显的氧化峰,且氧化峰电流显著高于在MWCNT′s/GCE和裸玻碳电极上的氧化峰电流。提出了用微分脉冲伏安法测定左旋多巴的方法。左旋多巴的浓度在8.0×10~(-6)～2.0×10~(-1)mol·L~(-1)范围内与其氧化峰电流呈线性关系,检出限(3S/N)为1.9×10~(-6)mol·L~(-1),平均回收率为102.8%。     

聚对氨基苯磺酸修饰电极差分脉冲伏安法测定对乙酰氨基酚

在由pH 7.0的磷酸盐缓冲溶液和2.0×10~(-3)mol·L~(-1)对氨基苯磺酸组成的支持电解质中,以100mV·s~(-1)扫描速率在玻碳电极上先后在电位-1.5～2.5V范围内循环扫描10周、在电位-1.5～1.5V范围内循环扫描15min,制得聚对氨基苯磺酸修饰的玻碳电极。循环伏安法研究发现:对乙酰氨基酚在该修饰电极上出现了一对氧化还原峰,两峰的电位差为30mV;差分脉冲伏安法研究发现:在pH5.9的磷酸盐缓冲溶液中,对乙酰氨基酚在0.295V处出现一良好的氧化峰。且乙酰氨基酚的浓度在2.0×10~(-7)～1.0×10~(-5)mol·L~(-1)范围内与峰电流呈线性关系,检出限(3S/N)为9.0×10~(-8)mol·L~(-1)。据此提出了差分脉冲伏安法测定药片中对乙酰氨基酚的含量,3个样品的测定结果与标示值相符,测得平均回收率为98.6%,相对标准偏差(n=6)均小于3.5%。     

Differential Pulse Voltammetric Determination of L-Cysteine After Cyclic Voltammetry in Presence of Catechol with Glassy Carbon Electrode

An electrochemical method of determination of cysteine has been developed in the solution containing catechol as the indicator. Nucleophilic addition of the thiol species to the electrogenerated o-quinone results in the formation of o-quinone-cysteine adducts that easily accumulate use at the surface of the electrode in the acidic solution. Therefore, the use of cyclic voltammetry leads to the amplification of the o-quinone-cysteine adduct's reductive current. As cyclic voltammetry was performed prior to differential pulse voltammetry, the peak of o-quinone-cysteine could be separated preferentially from o-quinone in the differential pulse voltammogram and the selectivity of the method has been assessed with no interference from ascorbic acid, glycine, L-tyrosine, or L-lysine. The magnitude of o-quinone-cysteine peak is proportional to the concentration of cysteine, and thus it can be exploited to determine cysteine within the injection. The results were consistent with those obtained by means of HPLC analysis.     

Stripping Voltammetric Determination of Methyl Parathion at Activated Carbon Nanopowder Modified Electrode

An activated carbon nanopowder modified glassy carbon electrode (AC-GCE) was constructed for the sensitive determination of methyl parathion by adsorptive differential pulse anodic stripping voltammetry. The simple and rapid modification procedure included only drop-coating the electrode surface with a laponite stabilized activated carbon nanopowder suspension and drying. The modifier high adsorption ability, combined with its large electroactive surface area allowed a 30-fold signal increase to be achieved, compared to bare GCE. Under optimized experimental conditions (activated carbon to laponite ratio, pH and accumulation time), the AC-GCE exhibited a linear response to methyl parathion in two concentration ranges: from 0.01 μmol L⁻¹ to 1 μmol L⁻¹ and from 1 μmol L⁻¹ to 6 μmol L⁻¹. The LOD of 2.5 nmol L⁻¹ (S/N=3) achieved fitted with regulatory norms. It was demonstrated that the as-prepared AC-GCE is suitable for routine real samples analysis.     

Determination of Tetracycline at a UV‐Irradiated DNA Film Modified Glassy Carbon Electrode

In this study, interaction of tetracycline (TC) and DNA in the Britton? Robinson buffer solution (BR) was studied by cyclic voltammetry. The experimental results reveal that TC can bind strongly to DNA and the association constant and binding number between TC and DNA was obtained. Then DNA was immobilized on a glassy carbon electrode by UV‐irradiation. Through this process, water‐soluble DNA was converted into insoluble materials, and a stable DNA film was formed on the electrode. The electrochemical oxidation behavior of TC was studied at UV‐irradiated DNA film modified glassy carbon electrode (UV‐DNA‐GCE). The response of modified electrode was optimized with respect to pH, accumulation time, ionic strength, drug concentration and other variables. TC at the surface of modified electrode showed a linear dynamic range of 0.30–90.00 µM and a detection limit of 0.27 µM. To demonstrate the applicability of the modified electrode, it was used for the analysis of real samples such as pharmaceutical formulations and milk.     

Determination of Rutin by a Graphene-Modified Glassy Carbon Electrode

A reduced graphene oxide-modified glassy carbon electrode for sensitive detection of rutin is reported. The modified electrode was obtained by one-step electrochemical reduction of graphene oxide on the bare glassy carbon electrode. In the presence of graphene, an enhanced electrochemical response for rutin appeared with a pair of well-defined anodic and cathodic peaks in pH 3.0 phosphate buffer. Under the optimized conditions, the anodic peak currents exhibited a linear relationship with rutin concentration from 0.1 to 2.0 µM with a detection limit of 23.2 nM. The modified electrode was employed to the analysis of tablets (with satisfactory recovery of 19.96 mg/per tablet) and Flos Sophorae. The graphene-modified electrode exhibited high sensitivity, good stability, and selectivity for the determination of rutin.     

Electrochemical Detection of Alloxan on Reduced Graphene Oxide Modified Glassy Carbon Electrode

Alloxan is a toxic reagent that strongly induces the diabetes by destroying insulin‐producing β‐cells in the pancreas of living organisms. The reduction product of alloxan is dialuric acid, which is responsible for the intracellular generation of ROS to enhance the stress in living cells to cause kidney disease or diabetic nephropathy. Herein, we studied for the first time the electrochemical properties of alloxan on reduced graphene oxide modified glassy carbon electrode (rGO/GCE) in 0.1 M phosphate buffer solution (PBS) at pH 7. The obtained results were compared with graphene oxide modified GCE (GO/GCE) and bare GCE surfaces. The modified rGO/GCE showed well defined redox couple with 10 fold increase in both reduction as well as oxidation peak current for alloxan than that of GO/GCE and bare GCE. Differential pulse voltammetry (DPV) technique shows the linear increase in both oxidation and reduction peak current of alloxan in the range of 30 μM to 3 mM with LOD of 1.2 μM. An amperometric signal of alloxan is also increases with respect to each addition of 50 μM of alloxan on rGO/GCE at constant potential of ?0.05 V. The linear range of alloxan is observed between 50 μM to 750 μM (S/N=3). This kind of rGO/GCE surface is more suitable platform or sensor matrix for estimating unknown concentration of alloxan molecule in the real biological systems.     

氧化石墨烯/铁氰化铈修饰玻碳电极同时测定扑热息痛和咖啡因

采用滴涂法和电沉积法制备了氧化石墨烯/铁氰化铈(CeFe(CN)6)纳米复合膜修饰玻碳电极。用扫描电镜对氧化石墨烯和氧化石墨烯/CeFe(CN)6纳米复合膜进行了表征。分别用循环伏安法和差分脉冲伏安法研究了扑热息痛和咖啡因在修饰电极上的电化学行为。结果表明,在0.1 mol/L醋酸盐缓冲溶液(pH5.0)中,扑热息痛和咖啡因在此修饰电极上具有良好的电化学行为,扑热息痛和咖啡因分别在1.0×10-7～6.0×10-5mol/L和1.0×10-6～1.3×10-4mol/L浓度范围内与电化学响应信号呈良好的线性关系,相关系数分别为0.990和0.992;信噪比为3时,扑热息痛和咖啡因检出限分别为5.0×10-8mol/L和5.2×10-7mol/L。将本方法用于人尿样品分析,回收率为96.1%～105.4%。     

石墨烯-纳米金复合物修饰电极用于异烟肼及抗坏血酸的同时测定

制备了石墨烯-纳米金(GR/Au)复合物修饰的玻碳电极,并将其用于异烟肼(INZ)和抗坏血酸(AA)的同时检测。在0.1 mol·L-1PBS(pH 3.5)缓冲溶液中,采用循环伏安法分别考察了INZ及AA的电化学行为。结果显示,INZ及AA的氧化峰电流均与扫速(50~300 mV·s-1)的平方根呈良好线性关系,且复合物修饰电极对INZ及AA的氧化显示出高的催化性能,二者之间产生明显的峰分离(ΔV=170 mV)。在最优实验条件下,当AA存在时,INZ的氧化峰电流与其浓度在3.0×10-6~1.5×10-4mol·L-1范围内呈良好的线性关系,其检出限为8.0×10-7mol·L-1。而当INZ存在时,AA的氧化峰电流与其浓度在3.0×10-5~1.0×10-3mol·L-1范围内呈良好的线性关系,其检出限为6.0×10-6mol·L-1。将此修饰电极用于药物中INZ及AA的测定,结果满意。     

Simultaneous and Direct Determination of Tryptophan and Tyrosine at Boron‐Doped Diamond Electrode

A facile method for the simultaneous measurement of tryptophan (Trp) and tyrosine (Tyr) was firstly exploited at unmodified boron‐doped diamond (BDD) electrode. The experimental results indicated that by using differential pulse voltammetry, the oxidative peaks of these two kinds of amino acids could be completely separated at BDD electrode. The peak separation of Trp and Tyr was developed to be 0.64 V when Na₂PO₄/NaOH buffer solution with the optimized pH 11.2 was employed. The detection limit of Trp was obtained to be 1×10^?5 M, while that of Tyr was achieved to be 1×10^?6 M. The present method was also evidenced to be available to the determination of real samples of amino acids.     

Poly(Methyl Red) Modified Glassy Carbon Electrodes: Electrosynthesis,Characterization, and Sensor Behavior

Poly(methyl red), PMR, was electropolymerized on glassy carbon electrodes by potential cycling in 50 mM phosphate buffer solution at pH 7.0 and 8.0 and Britton Robinson buffer solution in the pH range 7.0‐11.0. The electrochemical behavior of PMR modified electrodes was investigated by cyclic voltammetry in Britton Robinson buffer solution at different pHs from 5.0 to 10.0 and found that the best PMR film formation was obtained at pH 9.0. Uric acid was quantitatively determined at PMR modified electrodes by cyclic voltammetry and differential pulse voltammetry in Britton Robinson buffer at pH 5.0. Both methods presented a linear dependence between the anodic peak current and the concentration of uric acid in the range of 0.4 to 60 μM and 0.08 to 100 μM with the limits of detection of 0.038 and 0.009 μM for cyclic voltammetry and differential pulse voltammetry, respectively. Poly(methyl red) as redox mediator allowed the determination of uric acid without any interferences from the substances in serum samples.     

Hemin Modified Carbon Fat Electrode for Analyzing Antimalarial Endoperoxide Artemisinin in Artemisia annua

A hemin bulk modified carbon electrode with Adeps neutralis (solid fat) as binder was developed for the determination of antimalarial endoperoxide artemisinin in plant matrix. The hemin modified electrode showed significant catalytic activity for the electrochemical reduction of artemisinin at about ?380 mV vs. Ag/AgCl in phosphate buffer solution of pH 7 by using cyclic and differential pulse voltammetry. Under optimized conditions strict linearity between artemisinin concentration and height of the cathodic catalytic current peak was observed in 4.8×10^?6–7.8×10^?5 M concentration range (R=0.9991) when using differential pulse voltammetry. The detection limit was calculated as 1.4×10^?6 M of artemisinin. The developed electroanalytical device is suitable for the determination of artemisinin in Artemisia annua extracts.     

银纳米粒子修饰银电极法测定酪氨酸

通过NaBH₄还原AgNO₃得到胶体银纳米粒子,制作了以该纳米粒子修饰的银电极。研究了银纳米粒子修饰银电极在电催化中的应用,并对相关机理进行了探讨。该修饰电极对醋酸具有电催化活性,但酪氨酸却对该催化信号有明显的抑制作用,因此建立了用胶体银纳米粒子修饰银电极在NaAc-HAc缓冲溶液中检测酪氨酸的方法,并讨论了最佳工作条件。结果表明：在pH = 5.5时,峰电流与酪氨酸的浓度在1.0×10_-8～1.0×10_-3mol L_-1 范围内呈良好的线性关系,检出限为4.2×10_-9 mol L_-1,线性回归方程为Ip (μA) = 7.64 pC – 15.69 ( R = 99.73% )。用该方法检测氨基酸注射液中酪氨酸的含量,加标回收率在95.2%~107.8%之间。     

日落黄在乙炔黑-壳聚糖修饰玻碳电极上的电化学行为研究

将新型炭材料乙炔黑(AB)分散制备成AB-壳聚糖(CTS)复合膜修饰玻碳电极(GCE)。运用循环伏安法(CV)和微分脉冲伏安法(DPV)研究了着色剂日落黄在该修饰电极上的电化学行为。通过对支持电解质、修饰剂的用量、富集电位、富集时间进行优化,建立了一种快速、灵敏测定日落黄的电化学分析方法。方法的线性范围为5.0×10-8~1.0×10-5 mol/L,检出限(S/N=3)为9.0×10-9 mol/L。该修饰电极制作简单,稳定性、重现性良好,已成功应用于实际样品的检测。     

邻氨基酚在硫堇分子自组装膜修饰金电极上的电化学行为及其测定

在 0 .0 5 mol/L p H4.2的 HAc- Na Ac- PHP(邻苯二甲酸氢钾 )缓冲溶液中 ,用硫堇分子自组装膜修饰金电极对邻氨基酚的电化学行为进行了初步研究。研究发现 ,邻氨基酚在 - 0 .1 V左右出现一可逆氧化还原峰 ,在 0 .38V( vs.SCE)左右产生一阳极峰。两峰均由邻氨基酚的氧化还原引起 ,较正处的阳极峰表现出吸附波的性质 ,该峰较灵敏 ,适于伏安测定。该峰的峰电流与邻氨基酚的浓度在 1 .0× 1 0 - 6 ～ 5 .0× 1 0 - 4mol/L范围内呈线性关系 (相关系数 r =0 .9991 )。该方法可用于邻氨基酚含量的测定     

硫桥杯[4]芳烃衍生物膜修饰玻碳电极差分脉冲溶出伏安法测定铅

将硫桥杯[4]芳烃衍生物25,27-二(2-噻二唑基硫代乙氧基)-26,28-二甲氧基-5,11,17,23-四叔丁基硫桥杯[4]芳烃(TTCA)溶于二氯甲烷中,滴涂在玻碳电极表面,制得硫桥杯[4]芳烃修饰的玻碳电极。循环伏安当研究结果表明:将此修饰电极浸泡在1.0×10-6mol.L-1铅(Ⅱ)溶液中一段时间后转移至0.1 mol.L-1硝酸溶液中,以扫速100 mV.s-1在电位-0.8~-0.2 V范围内扫描所得的CV图上出现一对氧化还原峰。当此修饰电极在上述浓度的铅(Ⅱ)溶液中于-1.1 V富集300 s后用差分脉冲溶出伏安法检测时,铅(Ⅱ)在-0.516 V处出现一良好的氧化峰。铅(Ⅱ)浓度在2.0×10-7~2.0×10-5mol.L-1范围内与峰电流呈线性关系。其检出限(3S/N)为8.0×10-9mol.L-1。此法应用于水样中痕量铅的测定,测得回收率在95.0%~104.0%之间。     

基于四氧化三铁磁性纳米粒子的微囊藻毒素免疫传感器研究

采用化学共沉淀法制备四氧化三铁(Fe3O4)磁性纳米粒子(MNPs),依次用3-氨基丙基三乙氧基硅烷(APTS)、丁二酸酐(SAH)对Fe3O4 MNPs表面进行修饰,得到羧基功能化的核壳型磁性纳米粒子(Fe3O4@APTS·SAH MNPs),分别采用透射电镜(TEM)、磁滞回线、X射线光电子能谱(XPS)和傅里叶红外光谱(FTIR)对其进行了表征.将此纳米粒子修饰在自制的磁性玻碳电极(MGCE)表面,用1-(3-二氨基丙基)-3-乙基碳二亚胺盐酸盐(EDC)和N-羟基琥珀酰亚胺(NHS)活化纳米粒子表面的羧基,通过与氨基的共价交联,将抗微囊藻毒素-(亮氨酸-精氨酸)(MCLR)抗体(anti-MCLR)固定于该修饰电极上,用牛血清白蛋白(BSA)封闭非特异性吸附位点,构建了一种检测MCLR的电流型免疫传感器.采用直接竞争免疫反应模式,在标记物辣根过氧化物酶(HRP)的MCLR (MCLR-HRP)存在下,利用差分脉冲伏安法(DPV)测定溶液中的微囊藻毒素.在优化的实验条件下,免疫传感器对MCLR的线性测定范围为0.05 ～ 100 μg/L,检出限为0.01 μg/L(S/N=3).构建的免疫传感器呈现出良好的重现性、稳定性和特异性.将本传感器用于实际水样的测定,加标回收率为94.3％ ～ 99.5％.     

用泛醌修饰的碳糊电极作葡萄糖传感器

本选择泛醌作酶电极电子传统递体，将它和葡萄糖氧化酶、碳糊混和组成一种新的葡萄糖传感器，电极性能较不含泛醌的电极更优越，峰高ｉｐ与葡萄糖浓度在０．８×１０＾－５－１．６×１０＾－４ｍｏｌ／Ｌ范围内呈线性关系，电极灵敏度较高，干扰少，响应快，使用寿命长达三周。     

在抗坏血酸存在下用L-赖氨酸修饰玻碳电极测定多巴胺

采用电化学氧化法制备了L-广赖氮酸单分子层修饰玻碳电极,研究了多巴胺（DA）和抗坏血酸（AA）在该电极上的电化学行为。结果表明,L-广赖氨酸单分子层修饰玻碳电极不仅能改善多巴胺和抗坏血酸的电化学行为,而且能将多巴胺和抗坏血酸二者在裸电极上的完全重叠的单氧化峰分开成为两个完全独立的氧化峰,循环伏安（CV）图上峰间距为507mV,差分脉冲伏安（DPV）图上峰间距为460mV,由此可实现在AA的共存下对样品中的DA进行选择性测定。