Novel thermotropic esters‐based polymers with broad nematic processing windows

In this study, a new series of semiflexible liquid crystalline (LC) polyesters and poly(ester‐amide)s were synthesized and characterized. Polymers based on 4‐hydroxybenzoic acid (4‐HBA), 6‐hydroxy‐2‐naphthoic acid (HNA), suberic acid (SUA), and sebacic acid (SEA) were modified with hydroquinone (HQ) and different concentrations of 4‐acetamidophenol (AP) to obtain a polyester and two poly(ester‐amide)s, respectively. All polymers were successfully prepared using conventional melt‐condensation techniques. The polymers were characterized by inherent viscosity measurements, SEC, hot‐stage polarizing microscopy, DSC, and TGA. The mechanical behavior was investigated using DMTA and tensile testing. All linear polymers have T_gs in the range of 50–80 °C and melt between 120 and 150 °C. Our polymers display good thermooxidative stabilities (5% wt loss at ～ 400 °C) and exhibit homogeneous nematic melt behavior over a wide temperature range (ΔN ～ 250 °C). The liquid crystal phase was lost when high concentrations of nonlinear monomers such as 3‐HBA (>27 mol %) and resorcinol (RC) (>23 mol %) were incorporated. The LC polyester based on 4‐HBA/HNA/HQ/SUA/SEA could easily be processed into good quality films and fibers. The films display good mechanical properties (E′ ～ 4 GPa) and high toughness, that is, ～ 15% elongation at break, at room temperature. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 6565–6574, 2008     

SIZE EXCLUSION CHROMATOGRAPHIC COLUMN PACKED WITH REGENERATED CELLULOSE GELS*

Microporous regenerated cellulose gel particles were prepared by mixing cellulose cuoxam with silk fibroin aspore former, and the mean pore size and pore volume of the pallicles were 525 nm and 7.27 mL g~(-1), respectively. Apreparative size-exclusion chromatography (SEC) column (550 mm×20 mm) packed with the cellulose gel particles wasused for the fractionation of two polysaccharides Dextran 07 (M_w = 7.14×10~4, d= 1.7) and Dextran 50(M_w = 50.5×10~4,d = 3.8) in water phase. The fractionation range of the stationary phase covered M_w from 3×10~3 to 1.1×10~6. The dailythroughput was 2.9 g for Dextran 07 (D07) and 4.3 g for Dextran 50 (D50) with a flow-rate of 1.5 mL min~(-1). The fractionsobtained by using the SEC were analyzed by an analytical SEC combined with laser light scattering (LLS), and thepolydispersity indices of fractions for Dextran 07 and Dextran 50 were determined to be 1.34-1.57 and 1.53-3.36,respectively. The preparative SEC is a simple, rapid, and suitable means not only for the fractionation of polysaccharides inwater but also for other polymers in organic solvents.     

One‐pot synthesis of isocyanate and methacrylate multifunctionalized polyisobutylene and polyisobutylene‐based amphiphilic networks

Amphiphilic polymer networks consisting of hydrophilic poly(2‐hydroxyethyl methacrylate) (PHEMA) and hydrophobic polyisobutylene (PIB) chains were synthesized from a cationic copolymer of isobutylene (IB) and 3‐isopropenyl‐α,α‐dimethylbenzyl isocyanate (IDI) prepared at ?50 °C in dichloromethane in conjunction with SnCl₄. The isocyanate groups of this random copolymer, PIB(NCO)_n, were subsequently transformed in situ to methacrylate (MA) groups in the dibutyltin dilaurate‐catalyzed reaction with 2‐hydroxyethyl methacrylate (HEMA) at 30 °C. The resulting PIB(MA)_n with number–average molecular weight 8200 and average functionality F_n ～ 4 per chain was in situ copolymerized radically with HEMA at 70 °C, giving rise to the amphiphilic networks containing 41 and 67 mol % HEMA. PHEMA–PIB network containing 43 mol % HEMA was also prepared by radical copolymerization of PIB(MA)_n precursor with HEMA using sequential synthesis. An amphiphilic nature of the resulting networks was proved by swelling in both water and n‐heptane. PIB(NCO)_n and PIB(MA)_n were characterized by FTIR spectroscopy, SEC and the latter also by ¹H NMR spectroscopy. Solid state ¹³C NMR spectroscopy was used for characterization of the resulting PHEMA–PIB networks. Whereas single glass‐transition temperature, T_g = ?67.4 °C, was observed for the rubbery crosslinked PIB prepared by reaction of PIB(NCO)_n with water, the PHEMA–PIB networks containing 67 and 41 mol % HEMA showed two T_g's: ?70.4 and 102.7 °C, and ?63 and 107.2 °C, respectively. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2891–2900, 2006     

Development and validation of UPLC‐MS/MS method for simultaneous determination of gestodene and ethinyl estradiol in rat plasma

A selective and sensitive ultra‐performance liquid chromatography method with tandem mass spectrometric detection for simultaneous determination of gestodene (GES) and ethinyl estradiol (EE) in rat plasma was developed and validated. GES, EE and the internal standard, norgestrel, were extracted with ethyl acetate, derivatized (EE only) with dansyl chloride and then back‐extracted into diethyl ether‐hexane (2:1, v/v). The separation was performed on an ACQUITY UPLC? BEH C₁₈ column with gradient elution using mobile phase consisting of acetonitrile and water (both containing 0.1% formic acid). The detection was carried out by means of electrospray ionization (ESI) mass spectrometry in positive ion mode with multiple‐reaction monitoring. Calibration curves of GES and EE were linear (r² ≥ 0.99) over the concentration ranges 1.59–159 and 0.196–78.4 ng/mL, respectively. The intra‐ and inter‐day precisions were not more than 6.9 and 12.9% for GES and 10.6 and 9.0% for EE, and the accuracies were ?2.5–8.0% for GES, and ?7.2–0.19% for EE, respectively. The method herein described was superior to previous methods and was applicable to the pharmacokinetic study of GES and EE in rats. Copyright © 2009 John Wiley & Sons, Ltd.     

Living/controlled cationic cyclopolymerization of divinyl ether with a cyclic acetal moiety: Synthesis of poly(vinyl ether)s with high glass transition temperature based on incorporation of cyclized main chain and cyclic side chains

Cationic cyclopolymerization of 2‐methyl‐5,5‐bis(vinyloxymethyl)‐1,3‐dioxane ( 1 ), a divinyl ether with a cyclic acetal group, was investigated with the HCl/ZnCl₂ initiating system in toluene and methylene chloride at ?30 °C. The reaction proceeded quantitatively to give gel‐free, soluble polymers in organic solvents. The number‐average molecular weight (M_n) of the polymers increased in direct proportion to monomer conversion, and further increased on addition of a fresh monomer feed to the almost completely polymerized reaction mixture, indicating that the polymerization proceeded in living/controlled manner. The contents of the unreacted vinyl groups in the produced soluble polymers were less than ～3 mol %, and therefore, the degree of cyclization was determined to be ～97%. In contrast, the pendant cyclic acetal groups remained intact in the polymers under the present cationic polymerization conditions. These facts show that cyclopolymerization of 1 almost exclusively occurred and the poly(vinyl ether)s with the cyclized repeating units and cyclic pendant acetal rings were obtained. Glass transition temperature (T_g) and thermal decomposition temperature (T_d) of poly( 1 ) (M_n = 7870, M_w/M_n = 1.57) were found to be 166 and 338 °C, respectively, indicating that poly( 1 ) had high T_g and high thermal stability. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 952–958, 2010     

Synthesis,characterization, and rheological properties of multiarm stars with poly(glycidol) core and poly(methyl methacrylate) arms by AGET ATRP

Well‐defined multiarm star block copolymers poly(glycidol)‐b‐poly(methyl methacrylate) (PGOHBr‐b‐PMMA_x) with an average number of PMMA arms of 85, 55, and 45 have been prepared. The core‐first approach has been selected as the methodology using atom transfer radical polymerization (ATRP) of MMA from an activated hyperbranched poly(glycidol) as the core. These activated hyperbranched macroinitiators were prepared by esterification of hyperbranched poly(glycidol) (PGOH) with 2‐bromoisobutyryl bromide. The effect of monomer/initiator ratio, catalyst concentration, time, temperature, and solvent on the growing of the arms has been studied in detail in order to optimize the process and to diminish the radical‐radical coupling. The final products and intermediates were characterized by means of size exclusion chromatography (SEC), nuclear magnetic resonance (NMR) and Fourier transform‐infrared (FTIR) spectroscopy. The length of PMMA arms was determined by SEC after cleavage of ester bond linked to PGOH core. Glass transition temperature (T_g), thermal stability and rheological properties of the multiarm star copolymers were also studied. Finally, tapping mode atomic force microscopy (TMAFM) allowed the clear visualization of nano‐sized particles (80–200 nm) corresponding to individual star molecules. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Role of grafting in the emulsion polymerization of vinyl acetate with poly(vinyl alcohol) as an emulsifier. I. Effect of the degree of blockiness on the kinetics and mechanism of grafting

The role of grafting in particle nucleation during the emulsion polymerization of vinyl acetate with partially hydrolyzed poly(vinyl alcohol) (PVA) as an emulsifier and potassium persulfate as an initiator was investigated. The polymerizations were carried out in batch with a low solids (10%) recipe. An automated reaction calorimeter (Mettler RC1) was used for the direct monitoring of the kinetics of emulsion polymerizations with three medium molecular weight PVAs differing in their degrees of blockiness (Poval 217EE > 217E > 217). Smith–Ewart case 1 kinetics (average number of free radicals per particle < 0.5) were followed in all cases, and no constant rate in interval II was observed. Contrary to what was expected, a nonlinear relationship was observed between the rate of polymerization (R_p) and the number of particles (N_p). At R_{p max,} N_p (217E) > N_p (217EE) > N_p (217), and the final N_p was independent of the degree of blockiness of PVA. The particle size distributions were broad (particle diameter = 20–100 nm) and bimodal. On the basis of these data, we concluded that particle nucleation was continuous and was accompanied by extensive limited aggregation during the particle growth stages. The evolution of the amounts of grafted PVA and poly(vinyl acetate) (PVAc) were determined in polymerizations employing the two PVAs differing the most in blockiness (Poval 217EE and 217). The grafted PVAc followed similar profiles, increasing with conversion, particularly near the end of the two reactions. The amounts of grafted PVAc were about the same in the final latexes (37–39%). In contrast, the grafting of PVA was nearly complete by the time monomer droplets had disappeared in each reaction (25% conversion). However, the extent of grafting differed significantly, with the blockier PVA having about one‐third the grafting of the more random PVA (～10% vs ～30%). In these low solids recipes, grafting appeared to be primarily a solution event, occurring predominantly in the aqueous phase and not at the particle/water interface, as was previously speculated. The PVAc grafts grew until the molecules became water‐insoluble and precipitated, forming polymer particles. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 3633–3654, 2001     

Branched poly(1,4‐butylene carbonate‐co‐terephthalate)s: LDPE‐like semicrystalline thermoplastics

Branched poly[1,4‐butylene carbonate‐co‐terephthalate]s (PBCTs) have been synthesized by the addition of a small amount of glycerol propoxylate ( 1 ) or pentaerythritol ( 2 ) in the polycondensation of 1,4‐butanediol, dimethyl carbonate, and dimethyl terephthalate. To avoid gel formation, the feed amount of 1 or 2 was carefully controlled at below 0.5 mol % for 1 and below 0.3 mol % for 2 . When feed of 1 or 2 was used, a high‐molecular weight melt state (M_w ～180,000 g/mol) was reached in a total reaction time of 5.5 to 6.5 h with a yield higher than 90%. The generated PBCTs were a semicrystalline polymer (T_g ～5 °C and T_m ～120 °C) when the terephthalate content (F_[TPA]) was 45 to 50 mol %. The crystallization rate increased with increasing F_[TPA] and branch content (F_{[ 1 or 2 ]}); PBCT composed of F_[TPA] = 49 mol % and F_{[ 1 ]} = 0.44 mol % was crystallized completely in a short time, ～3 min, at a crystallization temperature of 50 °C. The branched PBCT exhibited more pronounced toughness in tensile test while providing the advantage of processibility at high shear rates due to the pronounced shear thinning in melt. It was also found that the branched PBCTs were biodegradable. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 914–923     

Sulfonated liquid crystalline polyesters as resin matrix for single wall carbon nanotube and nanodiamond composites

The focus of this study is on incorporating pendant sulfonate groups along the backbone of a liquid crystalline polyester (LCPE) with the aim to improve the dispersion of single wall carbon nanotubes (SWNTs) and nanodiamonds (NDs). Two LCPE matrices, one sulfonated (LCPE‐S) and one nonsulfonated reference polymer (LCPE‐R), were successfully synthesized via a melt condensation method using aromatic and aliphatic AB, AA, and BB‐type monomers. Upon the introduction of SWNT and ND particles, the glass transition temperature (T_g) of the sulfonated LCPE increased from 21.5 °C to 41.0 °C and 41.9 °C, for SWNTs and NDs, respectively. When sulfonate groups were absent, a decrease in T_g was observed. The storage modulus (E′) followed a similar trend, i.e., E′ increased from 1.3 GPa to 5.2 GPa and 3.4 GPa, upon the addition of NDs and SWNTs. The LCPE‐S showed a lower thermal stability due to the loss of sulfonate groups, i.e. the 5% weight loss temperature (T) is ～280 °C for LCPE‐S vs. 333 °C for LCPE‐R. The decomposition temperature increased somewhat upon addition of the nanoparticles. The ability of dispersing carbon‐based nanostructures combined with an accessible melt processing window makes sulfonated LCPs attractive matrices towards preparing nanocomposites with improved thermal and mechanical properties. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011.     

High Tg microspheres by dispersion copolymerization of N‐phenylmaleimide with styrenic or alkyl vinyl ether monomers

Solution and dispersion copolymerizations of N‐phenylmaleimide (PMI) with either styrenics or alkyl vinyl ethers (AVEs), systems with a tendency to give alternating polymers, were investigated with the goal of producing high glass transition particles. Equimolar solution copolymerization of PMI with styrenics gave alternating copolymers, whereas AVEs gave PMI‐rich copolymers (～65:35) except for t‐butyl vinyl ether, which gave copolymers with only a slight excess of PMI. These copolymers had glass transition temperatures (T_gs) ranging from 115 to 225 °C depending on comonomer(s). Dispersion copolymerization in ethanol‐based solvents in the presence of poly(vinylpyrrolidone) as steric stabilizer led to narrow‐disperse microspheres for many copolymers studied. Dispersion copolymeriations of PMI with styrenics required good cosolvents such as acetonitrile or methyl ethyl ketone as plasticizers during particle initiation and growth. Dispersion copolymerizations generally resulted in copolymer particles with compositions and T_gs very similar to those of the corresponding copolymers formed by solution polymerization, with the exception of t‐butyl vinyl ether (tBVE), which now behaved like the other AVEs. Dispersion terpolymerizations of PMI (50 mol %) with different ratios of either n‐butylstyrene and t‐butylstyrene or n‐butyl vinyl ether and tBVE led to polymer particles with T_gs that depended on the ratio of the two butyl monomers. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Fibrillar structure of self‐assemblies formed from heterocomplementary monomers linked through sextuple hydrogen‐bonding arrays

The nanostructure of the fibrillar supramolecular aggregates generated in decane solutions of homoditopic heterocomplementary monomers forming sextuple hydrogen‐bond‐mediated self‐assemblies was investigated by small‐angle neutron scattering and cryogenic‐temperature transmission electron microscopy. The persistence length (L_p) of the fibrillar aggregates was found to be ～18 nm, as inferred from combined measurements of the radius of gyration and of the contour length. The values of both the weight‐average molecular weight and the mass per unit length of the fibers suggest that the latter consist of few aggregated monomolecular wires. At T = 25 °C, the formation of branched aggregates occurs around the crossover concentration, C*, between the dilute and semidilute regimes, whereas the classical behavior of equilibrium polymers is observed at T = 65 °C. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 103–115, 2007     

Effect on structural relaxation of the poly(methyl‐methacrylate) copolymers chain flexibility

The structural relaxation of poly(methyl‐methacrylate) (PMMA)‐based copolymers with different chain flexibility has been studied by DSC with the classical procedure of the isothermal and dynamical approach. Modified PMMA with different chain flexibility have been prepared by free radical polymerization in solution using a mixture of monomers containing 10 mol % of alkyl methacrylate (i.e., ethyl, buthyl, and hexyl methacrylate). The molecular characteristics of all the prepared copolymers have been performed by a multiangle laser light scattering (MALS) photometer on‐line to a size exclusion chromatography (SEC) system (SEC‐MALS) after and before the thermal treatments, NMR (¹H and ¹³C) and MALDI‐TOF mass spectrometry. A comparison of the apparent relaxation rate (R_H) was appraised from the enthalpy loss by annealing the different samples at the same level of undercooling (T_a = T_g ? 18 °C). It was found an increase of R_H increasing the chain flexibility in the copolymers. Dynamical tests, performed at different cooling rates, have been used to estimate the apparent activation energy of the relaxation process. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 596–607, 2009     

Superdrawing of polytetrafluoroethylene virgin powder above the static melting temperature

A new two‐stage draw technique was successfully applied to the superdrawing of polytetrafluoroethylene (PTFE) virgin powder. A film, compression‐molded from powder below the melting temperature (T_m = 335 °C), was initially solid‐state coextruded to an extrusion draw ratio (EDR) of 6–20 at 325 °C, about 10 °C below the T_m. These extrudates from the first‐stage draw were further drawn by a second‐stage pin draw in the temperature (T_d) range of 300–370 °C that covers the static T_m. The maximum achievable total draw ratio was ～60 at a T_d = 300 °C and increased rapidly with increasing T_d, reaching a maximum of 100–160 at a temperature window between 340 and 360 °C, depending on the initial EDRs. At yet higher T_d's, the ductility was lost as a result of melting. The high ductility of the PTFE extrudates at such high temperatures was ascribed to the improvement of interfacial adhesion and bonding between the deformed powder particles upon the first‐stage extrusion combined with the rapid heating of only a portion of the extrudate followed by the elongation at a high rate. The highly drawn fibers were highly crystalline (χ_c ≤ 87%) and showed high chain orientation (f_c ≤ 0.997) and a large crystallite size along the chain axis (D₀₀₁₅ ≤ 160 nm). The molecular draw ratio, estimated from the entropic shrinkage above the T_m, was close to the macroscopic deformation ratio independently of the initial EDRs. These results indicate that the draw was highly efficient in terms of chain extension, orientation, and crystallization. Thus, the maximum tensile modulus and strength achieved in this work were 102 ± 5 and 1.4 ± 0.2 GPa, respectively, at 24 °C. These tensile properties are among the highest ever reported on oriented PTFE. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 1995–2004, 2001     

Influence of long‐chain branching on the miscibility of poly(ethylene‐r‐ethylethylene) blends with different microstructures

The melt miscibility of two series of poly(ethylene‐r‐ethylethylene) (PE_Exx) polymers with different percentages (xx) of ethylethylene (EE) repeat units was examined with small‐angle neutron scattering (SANS). The first series consisted of comb/linear blends in which the first component is a heavily branched comb polymer (B90) containing 90% EE and an average of 62 long branches with a weight‐average molecular weight (M_W) of 5.5 kg/mol attached to a backbone with M_W = 10.0 kg/mol. The comb polymer was blended with six linear PE_Exx copolymers, all of which had M_W ≈ 60 kg/mol and EE percentages ranging from 55 to 90%; they were denoted L55 to L90, with the number referring to the percentage of EE repeat units. The second series consisted of linear/linear blends; the first component, with M_W = 220 kg/mol and 90% EE, was denoted L90A, and the second components were the same series of linear polymers, with M_W ≈ 60 kg/mol and various EE compositions. The concentrations investigated were 50/50 w/w, except for the blend of branched B90 and linear L90 (both components were 90% EE), for which 25/75 and 75/25 concentrations were also examined. The SANS results indicated that for the comb/linear blends, only the dB90/L90 blends were miscible, whereas the other five blends phase‐separated; for the linear/linear blends, dL90A/L83 and dL90A/L78 were miscible, whereas the other three blends were immiscible. These results indicate that long‐chain branching significantly narrowed the miscibility window of these polyolefin blends. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 466–477, 2002; DOI 10.1002/polb.10102     

Unique morphological and thermal behaviors of reorganized poly(ethylene terephthalates)

Bulk poly(ethylene terephthalate) PET has been reorganized both morphologically and conformationally by processing from its inclusion complex (IC) formed with γ‐cyclodextrin (CD). In the narrow channels of its γ‐CD‐IC crystals the included guest PET chains are isolated from neighboring PET chains and the ethylene glycol (EG) units adopt the highly extended g±tg? kink conformations, whose cross‐sectional diameters are ～80% of the diameter of the fully extended, all‐trans crystalline PET conformer, though they are nearly (～95%) as extended. When the highly extended, unentangled guest PET chains are coalesced from their γ‐CD‐IC crystals by exposure to hot water, host γ‐CDs are removed and the PET chains are presumably consolidated into a bulk sample with a morphology and constituent chain conformations not normally found in PET samples solidified from their randomly coiling, possibly entangled, disordered melts and solutions. Observations by polarized light and atomic force microscopies provide visual evidence for widely different semicrystalline morphologies developed in coalesced and as‐received PETs when crystallized from their melts, with possibly chain extended, small crystals and spherulitic, chain‐folded, large crystals, respectively. DSC observations reveal that coalesced PET is rapidly crystallizable from the melt, while as‐received PET is slow to crystallize and is easily quenched into a totally amorphous sample. Analyses of ¹³C‐NMR data strongly indicate that the PET chains in the noncrystalline regions of the coalesced sample remain predominantly in the highly extended kink conformations, with g±tg? EG units, which are required by their inclusion into PET‐γ‐CD‐IC crystals, while the predominantly amorphous PET chains in the as‐received sample have high concentrations of gauche± ? CH₂? CH₂? and trans ? O? CH₂? ,? CH₂? O? EG bond conformations. ¹³C‐NMR T₁(¹³C) and T_1ρ(¹H) relaxation studies show no evidence of a glass transition for coalesced PET, while the as‐received sample shows abrupt changes in both the MHz [T₁(¹³C)] and kHz [T_1ρ(¹H)] motions at T ～ T_g. Preliminary observations of differences in their macroscopic properties are attributed to the very different morphologies and conformations of the constituent chains in these PET samples. Apparently the kink conformers in the noncrystalline regions of coalesced PET are at least partially retained for extended periods even in the melt and are rapidly crystallized upon cooling. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 386–394, 2004     

Thermodynamic and kinetic thermal analyses on dual crystal forms in polymorphic poly(heptamethylene terephthalate)

Thermal analyses were performed for determining the equilibrium melting temperatures T of the respective α‐ and β‐crystal in melt‐crystallized polymorphic poly(heptamethylene terephthalate) (PHepT) using both linear and nonlinear Hoffman‐Weeks (H‐W) methods for comparison of validity. These two crystals in PHepT do not differ much in their melting temperatures. The equilibrium melting temperatures of the α‐ and β‐crystal as determined by the linear H‐W method are 98 °C and 100.1 °C, respectively; but the nonlinear H‐W method yielded higher values for both crystals. The equilibrium melting temperatures of the α‐ and β‐crystal according to the nonlinear H‐W method are 121 °C and 122.5 °C, respectively. Both methods consistently indicate that T of the β‐crystal is only slightly higher than that of the α‐crystal. Such small difference in T between the α‐ and the β‐crystal causes difficulties in judging the relative thermodynamic stability of these two crystals. Thus, kinetics of these two crystals was compared using the Avrami and Ozawa theory. The crystallization produced by quenching from T_max = 110 °C and 150 °C shows a heterogeneous and homogeneous nucleation mechanism, respectively. The lower T_max = 110 °C leads to heterogeneous nucleation and only α‐crystal in PHepT, whose crystallization rates at same T_c are much higher than crystallization rates by quenching from T_max = 150 °C leading to either α‐ or β‐crystal with homogeneous nucleation. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 1839–1851, 2009     

Simultaneous determination of etonogestrel and ethinyl estradiol in human plasma by UPLC‐MS/MS and its pharmacokinetic study

A selective, sensitive and rapid ultra‐performance liquid chromatography tandem mass spectrometry method was developed and validated for the simultaneous determination of etonogestrel (ENG) and ethinyl estradiol (EE) in human plasma. The analytes and their deuterated internal standards, ENG‐d7 and EE‐d4, were extracted from plasma samples by solid‐phase extraction on HyperSep™ Retain PEP cartridges. The chromatographic analysis was performed on an Acquity UPLC HSS Cyano column, 100 Å (50 × 2.1 mm, 1.8 μm), column using gradient mobile phase, acetonitrile and 2.0 mm ammonium trifluoroacetate at 0–1.7 min (65:35, v/v) and 1.8–2.7 min (95:5, v/v) with 0.250 mL/min flow rate. Analytes and IS protonated precursor → product ion transitions (ENG, m/z 325.2 → 257.2; EE, m/z 530.2 → 171.2; ENG‐d7, m/z 332.2 → 263.2; EE‐d4, m/z 534.2 → 171.2) were monitored on a Triple Quadrupole Mass spectrometer (TQMS), operating in multiple reaction monitoring and positive ionization mode. The calibration curves were established at 10.00–2500 pg/mL for ENG and 1.500–150.0 pg/mL for EE with a correlation coefficient (r²) ≥0.9996 for both. The validated method was successfully applied to support a bioequivalence study of 0.15 mg ENG and EE 0.03 mg tablet formulation, administered in 24 healthy Indian females. Method reliability was assessed by reanalysis of 94 incurred study samples.     

Long‐Lived Room‐Temperature Deep‐Red‐Emissive Intraligand Triplet Excited State of Naphthalimide in Cyclometalated IrIII Complexes and its Application in Triplet‐Triplet Annihilation‐Based Upconversion

Cyclometalated Ir^III complexes with acetylide ppy and bpy ligands were prepared (ppy=2‐phenylpyridine, bpy=2,2′‐bipyridine) in which naphthal ( Ir‐2 ) and naphthalimide (NI) were attached onto the ppy ( Ir‐3 ) and bpy ligands ( Ir‐4 ) through acetylide bonds. [Ir(ppy)₃] ( Ir‐1 ) was also prepared as a model complex. Room‐temperature phosphorescence was observed for the complexes; both neutral and cationic complexes Ir‐3 and Ir‐4 showed strong absorption in the visible range (ε=39600 M ^?1 cm^?1 at 402 nm and ε=25100 M ^?1 cm^?1 at 404 nm, respectively), long‐lived triplet excited states (τ_T=9.30 μs and 16.45 μs) and room‐temperature red emission (λ_em=640 nm, Φ_p=1.4 % and λ_em=627 nm, Φ_p=0.3 %; cf. Ir‐1 : ε=16600 M ^?1 cm^?1 at 382 nm, τ_em=1.16 μs, Φ_p=72.6 %). Ir‐3 was strongly phosphorescent in non‐polar solvent (i.e., toluene), but the emission was completely quenched in polar solvents (MeCN). Ir‐4 gave an opposite response to the solvent polarity, that is, stronger phosphorescence in polar solvents than in non‐polar solvents. Emission of Ir‐1 and Ir‐2 was not solvent‐polarity‐dependent. The T₁ excited states of Ir‐2 , Ir‐3 , and Ir‐4 were identified as mainly intraligand triplet excited states (³IL) by their small thermally induced Stokes shifts (ΔE_s), nanosecond time‐resolved transient difference absorption spectroscopy, and spin‐density analysis. The complexes were used as triplet photosensitizers for triplet‐triplet annihilation (TTA) upconversion and quantum yields of 7.1 % and 14.4 % were observed for Ir‐2 and Ir‐3 , respectively, whereas the upconversion was negligible for Ir‐1 and Ir‐4 . These results will be useful for designing visible‐light‐harvesting transition‐metal complexes and for their applications as triplet photosensitizers for photocatalysis, photovoltaics, TTA upconversion, etc.     

Formation of triblock copolymers via a tandem enhanced spin capturing—nitroxide‐mediated polymerization reaction sequence

The preparation of ABA‐type block copolymers via tandem enhanced spin capturing polymerization (ESCP) and nitroxide‐mediated polymerization (NMP) processes is explored in‐depth. Midchain alkoxyamine functional polystyrenes (M_n = 6200, 12,500 and 19,900 g mol^?1) were chain extended with styrene as well as tert‐butyl acrylate at elevated temperature NMP conditions (T = 110 °C) generating a tandem ESCP‐NMP sequence. Although the chain extensions and thus the block copolymer formation processes function well (yielding in the case of the chain extension with styrene number average molecular weights of up to 20,800 g mol^?1 (PDI = 1.22) when the 6200 g mol^?1 precursor is used and up to 67,500 g mol^?1 (PDI = 1.36) when the 19,900 g mol^?1 precursor is used and 21,600 g mol^?1 (PDI = 1.17) as well as 37,100 g mol^?1 (PDI = 1.21) for the tert‐butyl acrylate chain extensions for the 6200 and 12,500 g mol^?1 precursors, respectively), it is also evident that the efficiency of the block copolymer formation process decreases with an increasing chain length of the ESCP precursor macromolecules (i.e., for the 19,900 g mol^?1 ESCP precursor no efficient chain extension with tert‐butyl acrylate can be observed). For the polystyrene‐block‐tert‐butyl acrylate‐block‐polystyrene polymers, the molecular weights were determined via triple detection SEC using light scattering and small‐angle X‐ray scattering. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011.     

Rendering polyureas melt processible

Because of the presence of extensive H‐bonding in the hard segments, polyureas are processed by solution techniques (e.g., dry spinning) by the use of relatively costly and environmentally unfriendly solvents. Thus, the objective of this research was to render polyureas melt processible, (i.e., to reduce their flow temperature, T_flow) without compromising their excellent mechanical properties. We hypothesized and herein demonstrate that by using conventional chain extenders (CEs) in combination with small amounts of H‐bond acceptor chain extenders (HACEs), the T_flow of polyureas can be significantly reduced from ～230 to ～180 °C, and thus melt processible products with excellent mechanical properties can be obtained. We document the synthesis of conventional polytetramethylene oxide‐based and novel polyisobutylene (PIB)‐based polyureas with T_flows ～ 180 °C and excellent mechanicals by the addition of few percents of commercially available HACEs. Products were characterized by various techniques, including Instron (tensile strengths, elongations), durometer (Shore A Hardness), dynamic mechanical thermal analysis (T_flow), and thermal gravimetric analysis (TGA) (thermal weight loss). According to TGA, a polyurea with T_flow of ～180 °C did not degrade up to ～234 °C in air. A micromorphology for melt processible polyureas is proposed that emphasizes flexibilized hard segments in the presence of HACEs. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011