(PtAuPt)HN/GC的制备及对甲酸氧化的电催化性能

以Se溶胶为模板,合成了多层核壳结构的Se@Pt@Au@Pt实心纳米粒子;采用化学与电化学相结合的除硒方法制得了(PtAuPt)HN/GC,并表征了(PtAuPt-Se)HN的表面形貌、结构与组成;以甲酸为探针分子,比较了(PtAuPt)HN/GC和Pt/C/GC对甲酸氧化的电催化行为,发现(PtAuPt)HN/GC催化甲酸氧化只有1个氧化峰,峰电位和峰电流分别约为0.35V和1.22mA/cm2,而Pt/C/GC则有2个氧化峰,在0.35V时所对应的电流密度仅约为0.30mA/cm2,前者在该电位时的电流密度是后者的4倍;在0.30mA/cm2的电流密度下,(PtAuPt)HN/GC对应的电极电位为0.01V,比Pt/C/GC负移了340mV;在600s时的计时电流分别为0.06和0.02mA/cm2.(PtAuPt)HN对甲酸氧化的电催化活性不但比Pt/C高,而且具有一定的抗CO中毒性能.     

壳层厚度可调控的Ag@Pd@Pt纳米粒子的合成和甲酸电催化研究

在本课题组研究55 nm Au@Pd@Pt对甲酸电催化效果基础上,我们采用Ag取代Au制备55 nm Ag@Pd@Pt纳米粒子以降低催化剂的成本,并对甲酸的电催化行为进行研究. 研究表明：少量Pt的存在可大幅度提高催化剂的活性,当Pt的覆盖度为0.5 单原子层（ML）时,起始氧化电位最为靠前,氧化峰电流最大,这与Au@Pd@Pt纳米粒子对甲酸电催化行为类似. 与Au@Pd@Pt纳米粒子相比,其最佳起始氧化电位偏正0.05 V,但电催化活性并没有明显的降低. 通过改变催化剂比表面积研究甲酸的电催化行为,发现将9 nm Ag纳米粒子作为内核的9 nm Ag@Pd@Pt负载在活性炭中,在保持催化活性不变的情况下,碳载的催化剂价格可比55 nm Au@Pd@Pt纳米粒子降低220倍左右.     

甲酸在Pt-Ru/GC电极上氧化的SERS研究

采用循环伏安(CV)法、计时电流法和电化学原位表面增强拉曼散射光谱(SERS)技术研究了甲酸在Pt-Ru/GC电极上的氧化行为, 发现甲酸在Pt-Ru/GC电极上与在粗糙Pt电极上一样, 也能自发解离出强吸附中间体CO和活性中间体—COO－. 从分子水平证实钌的加入有利于提高电极对甲酸的电催化氧化活性, 当镀液中Pt：Ru的摩尔比从10∶1变化到1∶1, CO的氧化峰电位从0.41 V负移至0.35 V, 约负移了60 mV. Pt-Ru/GC(1∶1)电极与粗糙Pt电极相比, CO在电极表面氧化完毕的电位亦负移了约200 mV. 该研究结果表明, 电化学原位表面增强拉曼散射光谱技术可望成为研究电催化反应机理的普适谱学工具.     

直接甲醇燃料电池阳极催化剂的新体系: 纳米TiO2-CNT-PtNi复合纳米催化剂

采用电合成前驱体Ti(OEt)4直接水解法和电化学扫描电沉积法制备纳米TiO2-CNT-PtNi复合纳米催化剂.透射电镜(TEM)和X射线衍射(XRD)测试结果表明,纳米PtNi合金粒子(平均粒径8 nm)均匀地分散在纳米TiO2-CNT复合膜的三维网络结构中.通过暂态电化学方法研究表明,复合纳米催化剂的电化学活性比表面积为90 m2/g,对甲醇氧化具有很高的电催化活性和稳定性,常温常压下甲醇氧化峰电位为0.67和0.44 V,当温度为60℃时,氧化峰电位负移至0.64和0.30V,氧化峰电流密度高达1.38Mcm2.复合纳米催化剂对甲醇电氧化的高催化活性和稳定性可归因于多元复合纳米组分的协同催化作用,这种作用导致CO在复合纳米催化剂上的弱吸附,从而避免了催化剂的中毒.     

偏钒酸钠对甲酸在Pd/C催化剂上氧化的电催化性能影响的机理

直接甲酸燃料电池的两大问题是Pd催化剂对甲酸氧化的电催化稳定性不好和Pd能催化甲酸分解。研究发现,当Pd/C在偏钒酸钠溶液中浸泡后能吸附上VO3-,吸附上VO3-的Pd/C催化剂对甲酸分解的催化性能会大大降低,由甲酸分解产生的CO的量也大大降低,使Pd/C催化剂被CO毒化的几率也大大降低,因此,在偏钒酸钠溶液中浸泡后的Pd/C催化剂对甲酸氧化的峰电流密度要比没有浸泡的Pd/C催化剂高13%左右。计时电流曲线的测量表明,6000 s时在偏钒酸钠溶液中浸泡后的Pd/C催化剂对甲酸氧化的峰电流密度要比没有浸泡的Pd/C催化剂高42%左右。结果证明,在偏钒酸钠溶液中浸泡能提高Pd/C催化剂对甲酸氧化的电催化活性,特别是电催化稳定性。     

高利用率多壁碳纳米管负载金铂合金纳米粒子催化剂在碱性溶液中的甲醇电催化氧化性能研究

使用乙二醇还原法合成了一系列高利用率多壁碳纳米管负载的金铂双金属纳米粒子电催化剂,在碱性溶液中由循环伏安和计时电流法测试该AuPt催化剂对于甲醇氧化反应的电催化活性.透射电子显微镜、X射线衍射与X射线能谱观测催化剂形貌,表征催化剂结构.结果表明,金铂双金属纳米粒子均匀分散在碳纳米管上,催化剂具有良好甲醇电氧化性能.实验表明Au/Pt/MWCNTs比为10∶8∶32(bymass)时,该催化剂具有最高甲醇电氧化峰电流密度与最负起始氧化电位.     

活性炭和石墨混合载体的Pt催化剂（Pt/CG）对乙醇氧化电催化活性的影响

用化学沉积法制备炭载Pt(Pt/C)和以活性炭与石墨作混合载体的Pt(Pt/CG)催化剂。实验结果表明，活性炭与石墨质量比影响Pt/CG催化剂对乙醇氧化的电催化活性。当活性炭与石墨的质量比为15∶1时，制得的Pt/CG催化剂对乙醇氧化的电催化活性最高。     

电沉积Pt-Au双金属催化剂及其对甲酸的电催化研究

以玻碳电极(GCE)为基体, 采用恒电位法制备Pt-Au双金属催化剂. 通过扫描电镜(SEM), X射线能量色散谱(EDX)及电化学方法对催化剂样品进行了表征. SEM结果表明, Pt-Au双金属催化剂的形貌近似球状, 表面粗糙. 循环伏安法和计时电流法的测试结果表明, Au的加入有利于双金属催化剂上甲酸的电催化氧化, 并提高了催化剂对甲酸氧化的抗毒化能力. 而甲酸在催化剂上的氧化机理则通过电化学阻抗技术得到进一步说明. 同时研究了双金属催化剂中Au的不同含量对甲酸氧化的影响, 当 Pt和Au物质的量比为1∶1.803时, Pt-Au/GC催化剂具有最佳的甲酸电催化氧化活性.     

直接甲醇燃料电池阳极催化剂的新体系: 纳米TiO2-CNT-PtNi复合纳米催化剂

采用电合成前驱体Ti(OEt)₄直接水解法和电化学扫描电沉积法制备纳米TiO₂-CNT-PtNi复合纳米催化剂. 透射电镜(TEM)和X射线衍射(XRD)测试结果表明, 纳米PtNi合金粒子(平均粒径8 nm)均匀地分散在纳米TiO₂-CNT复合膜的三维网络结构中. 通过暂态电化学方法研究表明, 复合纳米催化剂的电化学活性比表面积为90 m²/g, 对甲醇氧化具有很高的电催化活性和稳定性, 常温常压下甲醇氧化峰电位为0.67和0.44 V, 当温度为60 ℃时, 氧化峰电位负移至0.64和0.30 V, 氧化峰电流密度高达1.38 A/cm². 复合纳米催化剂对甲醇电氧化的高催化活性和稳定性可归因于多元复合纳米组分的协同催化作用, 这种作用导致CO在复合纳米催化剂上的弱吸附, 从而避免了催化剂的中毒.     

电化学合成Pt-Au复合催化剂及其对甲醇的电催化氧化

在ITO导电玻璃上, 采用循环伏安法制备Pt-Au复合催化剂. 通过扫描电镜(SEM), X射线能量色散谱(EDX), X射线衍射(XRD)及其电化学方法对催化剂样品进行了表征. SEM结果表明, Pt-Au复合催化剂的形貌近似球状粒子. 循环伏安法和计时电流法的测试结果表明, 复合催化剂中Au的加入有利于甲醇的电催化氧化, 并提高了Pt对甲醇氧化的抗毒化能力. 同时研究了复合催化剂中Au的不同含量对甲醇氧化的影响, 结果表明, 当 Pt和Au物质的量比为1.07∶1时, Pt-Au/ITO催化剂具有最佳的甲醇电催化氧化活性.     

Solvent extraction separation of In/III/-Tl/III/ and Hg/II/-Cd/II/-Co/II/ with sulphoxides

Solvent extraction studies have been made on some metals: In/III/-Tl/III/ and Hg/II/-Cd/II/-Co/II/, from ammonium thiocyanate solutions by dialkyl sulphoxides. Separation of these metals from one another can be achieved by suitable choice of the extracted conditions. The nature of the extractable metal species has been elucidated.     

Simultaneous propane dehydrogenation andco2hydrogenation overCrOx/SiO2catalyst

Summary Single reverse water-gas shift (RWGS) and dehydrogenation of propane with CO₂(DH-CO₂) reactions in the presence and absence of the CrO_x/SiO₂ catalyst have been studied between 673 and 873 K. It was found that the CrO_x/SiO₂ catalyst is active both in the dehydrogenation of propane and in the RWGS reactions. The obtained results suggest that the dehydrogenation of propane to propene in the presence of CO₂on CrO_x/SiO₂can be facilitated by the RWGS reaction.</o:p>     

Synthesis of chlorobis/β-diketonato/oxotechnetium/V/ and tris/β-diketonato/technetium/III/ complexes

Chlorobis/-diketonato/ oxotechnetium/V/ complexes [TcOCl/-dik/₂, -diketone=acetylacetone, benzoylacetone and dibenzoylmethane] were newly synthesized using macroamount of⁹⁹Tc. These complexes were further separated into geometrical isomers. Furthermore, an improvement of the yields for the syntheses of tris/-dike-tonato/technetium/III/ complexes [Tc/-dik/₃, -diketone=acetylacetone, benzoylacetone and 2-thenoyltrifluoroacetone] was examined using Tc/III/-thiourea complexes as a starting material.     

Direct synthesis of dimethyl carbonate ?from CH3OH AND CO2 by H3PW12O40/CexTi1-xO2 catalyst

Summary Ce_xTi_1-xO₂ and H₃PW₁₂O₄₀/Ce_xTi_1-xO₂ catalysts were prepared using a sol-gel method, and applied to the direct synthesis of dimethyl carbonate from methanol and carbon dioxide. H₃PW₁₂O₄₀/Ce_xTi_1-xO₂ showed a better catalytic performance than the corresponding Ce_xTi_1-xO₂, due to the bifunctional catalysis of Br?nsted acid sites (provided by H₃PW₁₂O₄₀) and base sites (provided by Ce_xTi_1-xO₂). H₃PW₁₂O₄₀/Ce_0.1Ti_0.9O₂ showed the highest catalytic performance among the H₃PW₁₂O₄₀/Ce_xTi_1-xO₂ catalysts.     

Crystal structure of Na3PO4 · 12H2O

The crystal structure of trisodium monophosphate hemihydrate was determined. The space group is $\text{C2}\text{c}$ and a unit cell contains eight formula units. The unit cell dimensions of $\text{Na}{}_3\text{PO}{}_4\text{·}\text{1}\text{2}\text{H}{}_2\text{O}$ are a = 9.631(3), b = 5.416(2), c = 16.938(8) Å, β = 102.60(5)°. The final R value is 0.027 for a set of 1430 independent reflections. This atomic arrangement is mainly a three-dimensional network of distorted NaO₆ octahedra. The hydrogen bonding scheme is given.     

LixNi0.8-yCo0.2ZnyOp的合成及电化学性能研究

A series of single-phase Li_xNi_0.8-yCo_0.2Zn_yO_p(0.96 ≤x≤ 1.10， 0 ≤y≤ 0.05， 2 ≤p≤ 2(1+y) ) (different in the y values) were synthesized by a two-step solid state reaction method， in which LiOH·H₂O， Zn-doped spherical Ni(OH)₂ and Co₂O₃ were used as the precursors. The ICP-AES analyses proved that the Zn-doped compounds synthesized had the nonstoichiometric form. The results of the XRD， SEM identified that the uniform particles of the as-prepared materials having a good layered structure were fine， narrowly distributed and well crystallized. The electrochemical performance test was carried out and the results showed that the as-prepared Zn-doped materials had not only a high capacity， but also a better cycling stability characterization than the un-doped one. The Li_1.06Ni_0.75Co_0.22Zn_0.03O_2.03 material has an initial reversible capacity as high as 160.5mAh·g^-1; and a first discharge efficiency 89.2%， and exhibits satisfactory cyclic stability with 90% retainable capacity after 50 cycles.     

Synthesis and characterization of Ti1−2xNbxNixO2−x/2 solid solutions

Doped-rutile has been traditionally used in ceramic pigments for its intense optical properties. In this paper, we compare the classical ceramic synthesis of Ti_1−2xNb_xNi_xO_2−x/2 system with the sol-gel methodology, which allows a reduction of the anatase-rutile transformation temperature. The composition was optimised in order to obtain a unique rutile phase with the minimum amount of pollutant Ni(II) and enhanced chromatic coordinates. Incorporation of the doping ions in the rutile structure was corroborated by XRD and Rietveld refinements. The species responsible for the colour mechanism were studied by different techniques. UV-VIS spectroscopy showed the characteristic features of Ni²⁺ ions, whose existence was corroborated by EPR and magnetic measurements. From these results, (Ni,Nb)doped-TiO₂ powder samples can be now shaped as thin films, monoliths, etc. by using sol-gel methodology without modifying their properties. This study introduces new possibilities of coloured TiO₂-based solid solutions in new combined advanced applications (colouring agent and photocatalyst, etc.).     

An investigation of the promotional effect of propylene or propane traces on the activity of sulfatedPt/g-Al2O3andPt-Sn/g-Al2O3inCH4combustion

Summary A strong promoting effect of the presence of C₃H₈or C₃H₆was determined for the combustion of CH₄in excess oxygen, over pre-sulfated 1%Pt/g-Al₂O₃and pre-sulfated 1%Pt-2%Sn/g-Al₂O₃catalysts.</o:p>     

Visible light-sensitive yellow TiO2−xNx and Fe-N co-doped Ti1−yFeyO2−xNx anatase photocatalysts

Nitrogen substituted yellow colored anatase TiO_2−xN_x and Fe-N co-doped Ti_1−yFe_yO_2−xN_x have been easily synthesized by novel hydrazine method. White anatase TiO_2−δ and N/Fe-N-doped samples are semiconducting and the presence of ESR signals at g ∼1.994-2.0025 supports the oxygen vacancy and g∼4.3 indicates Fe³⁺ in the lattice. TiO_2−xN_x has higher conductivity than TiO_2−x and Fe/Fe-N-doped anatase and the UV absorption edge of white TiO_2−x extends in the visible region in N, Fe and Fe-N co-doped TiO₂, which show, respectively, two band gaps at ∼3.25/2.63, ∼3.31/2.44 and 2.8/2.44 eV. An activation energy of ∼1.8 eV is observed in Arrhenius log resistivity vs. 1/T plots for all samples. All TiO₂ and Fe-doped TiO₂ show low 2-propanol photodegradation activity but have significant NO photodestruction capability, both in UV and visible regions, while standard Degussa P-25 is incapable in destroying NO in the visible region The mid-gap levels that these N and Fe-N-doped TiO₂ consist may cause this discrepancy in their photocatalytic activities.     

LixZryOz三元化合物的制备及表征

采用高温固相法制备了4种高纯度晶相组成的LixZryOz三元化合物,研究了焙烧温度、时间、反应物的种类和初始反应物物质的量比对产物组成的影响,进一步用XRD、SEM及BET分析方法对产物的晶相结构、表面形貌及比表面积进行了表征.实验结果表明,Li2CO3与ZrO2在适当条件下可以合成得到单斜相Li3ZrO3;以LiOH替代Li2CO3,在适当条件下可以分别合成得到四方相Li2ZrO3和三斜/单斜相Li6Zr2O7;进一步以Zr(NO3)4·5H2O代替Zr02,可将单斜相Li6Zr2O7的制备时间由96 h缩短至24 h.SEM照片显示产物硬团聚明显,粒径分布在1～10μm间,BET分析表明样品比表面积处于1.0～9.0 m2·g-1间分布,反应过程中锂的过量以及长时间高温焙烧是引起产物粒径长大和产生硬团聚的主要原因.