盐酸环丙沙星在导电碳黑糊电极上的伏安行为及其检测应用

本文研究了盐酸环丙沙星(Cipro)在导电碳黑糊电极上的伏安行为,结果表明:B-R缓冲溶液(p H 4.0)中,该药物分子发生2质子、2电子转移的不可逆电化学氧化,过程受吸附控制,电子转移系数α为0.37,表面反应标准速率常数k's为0.95 s-1。实验研究了支持电解质种类、p H值、离子强度、富集电位与时间等对其伏安响应的影响,并据结果对检测条件进行优化,进而建立了Cipro的电化学检测方法。优化条件下,Cipro的氧化峰电流(ipa)与其浓度(C0)在2.5×10-7~6.0×10-5mol·L-1范围内呈良好的线性关系,检测限为9.5×10-8mol·L-1(S/N=3)。将该方法应用于测定淡水渔业水样中痕量Cipro,得到了较满意的结果(平均回收率102.73%)。     

结晶紫在导电碳黑糊电极上的伏安行为及其检测

结晶紫(CV)在导电碳黑糊电极(CCBPE)上具有灵敏的伏安响应,实验对其氧化还原机理进行了推导,结果表明:以pH 8.0的B-R缓冲液为支持电解质,CV发生2电子转移的不可逆氧化,过程受吸附控制。在富集时间、富集电位、pH等影响因子得到优化情况下,其半微分-脉冲伏安扫描氧化峰值与其浓度在0.03~1.30μmol/L范围内呈线性,检出限为10 nmol/L。据此建立了CV的电化学快检方法,并应用于淡水渔业水体中痕量CV的测定,平均回收率为97.1%。     

多菌灵在玻碳电极上的伏安行为及其应用

应用循环伏安法、微分脉冲伏安法对多菌灵在破碳电极上的电化学行为及其测定进行了研究。在ｐＨ＝９．０的２ｍｏｌ／Ｌ ＮＨ３－ＮＨ４Ｃｌ底液中，对其进行循环伏安扫描，发现于０．６１Ｖ（ｖｓ．Ａｇ／ＡｇＣｌ）产生一灵敏的氧化峰。微分脉冲伏安法殉菌灵的检测限为４×１０＾－８ｍｏｌ／Ｌ。多菌灵的浓度在５．０×１０＾－７￣１．０×１０＾－５ｍｏｌ／Ｌ间与微分脉冲伏安峰电流呈线性关系（ｒ＝０．９９４２）。对于１×     

碳糊修饰电极吸附伏安法测定食品中的锑

研制了溴邻苯三酚红 (BPR)作修饰剂的碳糊修饰电极 ,并用此电极作工作电极建立了测定痕量锑的吸附伏安法。在选定的实验条件下 ,峰电流与Sb(Ⅲ )浓度在 8.0× 1 0 -9～ 2 .0× 1 0 -7mol L范围内呈线性关系 ,检出限为 2 .0×1 0 -9mol L ,1 0次测定相对标准偏差为 2 .0 % ,不用分离 ,可直接测定食品中痕量Sb(Ⅲ ) ,测定的回收率为 90 %～ 1 0 3%。     

肾上腺素在预阳极化碳糊电极上的电化学行为研究

建立了预阳极化碳糊电极(PACPE)测定肾上腺素(EP)的新方法。实验表明,EP在PACPE上有很好的电化学响应,在pH 7.00的PBS缓冲溶液中,EP的氧化峰电流最大,且与其浓度在2.0×10-7~1.0×10-4mol/L范围内呈良好的线性关系,线性方程为:Ip(μA)=0.4598+0.1544c(μmol/L),相关系数R=0.9981,检出限为2.9×10-8mol/L。方法可用于注射液中EP含量的测定。     

白藜芦醇在银电极上的吸附伏安行为及其应用

白藜芦醇(3,5,4-三羟基芪)通常存在于葡萄、桑椹等多种植物中, 葡萄酒中也有一定的含量[1]. 由于白藜芦醇对防治癌症、动脉硬化和冠心病等疾病有较好的疗效[1,2], 近年来对白藜芦醇生物活性的研究日益受到重视. 白藜芦醇的测定一般采用高效液相色谱和毛细管电泳等方法[3～5], 这些方法均需对样品进行减压浓缩和萃取等处理, 比较繁琐. 本文对白藜芦醇在银电极上的吸附伏安行为进行了研究, 并将其应用于葡萄酒中白藜芦醇含量的直接测定, 获得了较好的实验结果.     

芦丁在玻碳电极上的阳极伏安行为及其测定

本文应用线性扫描伏安法，微分脉冲伏安和循环伏安法对芦丁在玻碳电极上的阳极伏安行为进行了研究。     

辛硫磷在玻碳电极上的伏安行为

在以0.1 mol.L-1氯化钾为支持电解质,pH为2.21的B-R缓冲溶液中辛硫磷于-0.72 V(vs.Ag/AgCl)处产生灵敏的还原峰。当辛硫磷的浓度在4×10-5~8×10-4mol.L-1范围内时,浓度与线性扫描还原峰电流呈线性关系。据此对辛硫磷样品作6次平行测定,测得平均值为3.42%,其RSD为1.7%,回收率为98.6%~103.6%。用线性扫描与循环伏安法探讨了该体系的伏安行为,结果表明,辛硫磷在玻碳电极上的电化学还原机理为不可逆过程。     

盐酸川芎嗪在玻碳电极上的伏安行为及应用

对盐酸川芎嗪在玻碳电极上的伏安行为进行了研究 ,在 0 .0 1mol LKCl～HCl(pH 2 .2 )底液中盐酸川芎嗪于 -0 .5 5V处产生良好的阴极还原峰 ,其浓度在 1 0× 1 0 - 6 ～ 1 .0× 1 0 - 4mol L范围内与峰电流呈线性关系。该方法具有很强的抗干扰能力 ,操作简便、快速。用于注射液中盐酸川芎嗪的测定 ,结果满意。对电极反应机理也进行了探讨。     

Voltammetric behavior of urapidil and its determination at multi-wall carbon nanotube paste electrode

The voltammetric behavior of urapidil was investigated. In pH 6.8 Britton-Robinson buffer, an irreversible oxidation peak of urapidil at 0.62 V (versus SCE) at a multi-wall carbon nanotube paste electrode (MWNT-PE) was observed, which was more sensitive with lower potential than that at the carbon paste electrode (CPE). The oxidation of urapidil was a two-electron and two-proton process with adsorption character. A differential pulse voltammetric method was proposed for the determination of urapidil. The peak current of the oxidation peak of urapidil was linearly with its concentration in a range from 5.0 × 10⁻⁸ to 2.0 × 10⁻⁶ mol/L at open-circuit accumulation for 60 s, with a detection limit of 3.8 × 10⁻⁸ mol/L. The proposed method was employed to determine urapidil in urapidil tablets.     

Voltammetric determination of diethylstilbestrol at carbon paste electrode using cetylpyridine bromide as medium

In this paper, the voltammetric properties of diethylstilbestrol (DES) at the carbon paste electrode were described. The oxidation peak currents of DES increase significantly in the presence of surfactant cetylpyridine bromide (CPB), compared with that in the absence of CPB. Based on this fact, a voltammetric technique for determining DES is proposed. The accumulation potential has no effects on the peak current of the DES. An open-circuit accumulation is carried out. The experimental parameters, such as pH value of buffer, scan rate, and accumulation time were optimized. The interferences of some metal ions and organic compounds have also been studied, and some metal ions almost do not interfere with the determination of DES. Using this voltammetric method, DES in the injection sample was measured. The results show that this voltammetric method is reliable for the practice determination of DES.     

Voltammetric determination of azithromycin at the carbon paste electrode

Azithromycin (AZ) is the first member of a class of macrolide azalides antibiotics called azolides. A simple and selective square-wave voltammetric (SWV) method has been developed for the determination of azithromycin in pure form, in pharmaceutical preparation and in biological samples. Determination of azithromycin was accomplished with hand-make carbon paste electrode (CPE) in oxidative screen mode. The counter and reference electrodes were a Pt wire and a Ag/AgCl, respectively. Various parameters that can influence the peak signal (effect of buffer, ionic strength, accumulation time, pH and the composition of the paste) have been scrutinized. The best results were obtained in acetonitrile—aqueous 1 M sodium acetate-acetic acid buffer (pH 4.6) containing 0.1 M KCl (1:9; v/v) using a 15% paraffin oil CPE. The limits of detection and quantification of the pure drug are 0.463 and 1.544 ppb (with the correlation coefficient, r=0.9785and the standard deviation, S.D.=0.1 (n=5), for the accumulation time of 60 s), respectively. The method was successfully applied to the determination of the drug in urine and two forms of pharmaceutical formulations. Recoveries were 99.2—100.5% with S.D.=0.1—and 0.8% (n=5).     

Voltammetric determination of mifepristone at a DNA-modified carbon paste electrode

A new strategy for the preparation of a DNA-modified carbon paste electrode is developed. It is found that the anodic response of mifepristone is greatly enhanced at the dsDNA-modified carbon paste electrode comparing with that obtained at the bare electrode, while the response at a ssDNA-modified electrode is similar to bare electrode. So the dsDNA-modified electrode is employed as a sensitive biosensor for the detection of mifepristone. A linear dependence of the peak currents on the concentration is observed in the range 2.0 x 10(-7) approximately 2.0 x 10(6) mol/L, with a detection limit of 1.0 x 10(-7) mol/L. The relative standard deviation is 4.3% for six successive determinations of 1.0 x 10(6) mol/L mifepristone. The determination of mifepristone tablets is carried out and satisfactory results are obtained.     

对乙酰氨基酚在离子液体修饰碳糊电极上的电化学行为及其测定

用亲水性离子液体1-丁基-3-甲基咪唑四氟硼酸作修饰剂制备了离子液体修饰碳糊电极(IL/CPE).在pH4.78的Britton-Robinison缓冲溶液中,用循环伏安法和方波伏安法研究了对乙酰氨基酚在IL/CPE上的电化学行为.研究表明,IL/CPE对对乙酰氨基酚的氧化还原反应有良好的电催化作用.在方波伏安曲线上,对乙酰氨基酚的氧化电流与其浓度在8.0×10<'-7>～2.0×10<'-4>mol/L范围内呈线性关系,检出限为3.0×10<'-7>mol/L(S/N=3).建立了测定片剂中对乙酰氨基酚含量的新方法.     

Voltammetric determination of quercetin at a multi-walled carbon nanotubes paste electrode

Quercetin can effectively accumulate at multi-walled carbon nanotubes-paraffin oil paste electrodes (CNTPE) and cause a sensitive anodic peak at around 0.32 V (vs. SCE) in a 0.10 M phosphate buffer solution (pH = 4.0). Under optimized conditions, the anodic peak current is linear to quercetin concentration in the ranges of 2.0 × 10^− 9−1.0 × 10^− 7 M and 1.0 × 10^− 7−2.0 × 10^− 5 M, and the regression equations are i_p (μA) = 0.0017 + 0.928c (μM, r = 0.999) and i_p (μA) = 0.183 + 0.0731c (μM, r = 0.995), respectively. This paste electrode can be regenerated by repetitively cycling in a blank solution for about 2 min. A 1.0 × 10^− 6 M quercetin solution is measured for 10 times using the same electrode regenerated after every determination, and the relative standard deviation of the peak current is 1.7%. The method has been applied to the determination of quercetin in hydrolysate product of rutin and the recovery is 99.2–102.6%. In comparison with graphite paste electrode, carbon nanotubes-nujol paste electrode and carbon nanotubes casting film modified glassy carbon electrode, the CNTPE gives higher ratio of signal to background current and better defined voltammetric peak.     

Voltammetric determination of 2-nitrophenol at a bentonite-modified carbon paste electrode

A bentonite-modified carbon paste electrode has been applied to the determination of 2-nitrophenol by differential pulse voltammmetry. The electrochemical reduction of 2-nitrophenol at –0.8 V is carried out in an artificial sea water-formic acid/sodium formate medium at pH 4. The peak height was found to be dependent on the pH over the range 2–11; the presence of a secondary process was observed in the pH range 8–11. The peak potential showed a dependence on pH, with two linear regions with different slopes. A linear relationship between peak intensity and concentration was obtained in the range 0.07–10 mgl^–1, with a detection limit of 0.03 mg 1^–1 and a coefficient of variation of 1.3% at 5 mg 1^–1. The effects of organic and inorganic species on the 2-nitrophenol determination were studied with a view to testing the resolution of the voltammetric technique. The proposed method has been applied to sea water samples with good results.     

Voltammetric behavior and determination of bismuth on sodium humate modified carbon paste electrode

The preconcentration and voltammetric behavior of Bi^III on a sodium humate modified carbon paste electrode was studied by means of cyclic voltammetry (CV) and differential pulse stripping voltammetry (DPSV). The proposed measurement involves an initial nonelectrolytic preconcentration step in which Bi^III is complexed by the surface modifier in a solution of 0.05 M KNO₃-0.0106 M HNO₃ (pH 2.0) and a subsequent electrochemical scan step in which the preconcentrated Bi^III was reduced and then oxidized promptly in supporting electrolyte of 0.5 M HNO₃. The resulting DPSV anodic current was proportional to the concentration of Bi^III ion over the range of 4.78 × 10⁻⁸–1.44 × 10⁻⁵ M. The detection limit was 4.78 × 10⁻⁸ M. The proposed method was used to determine bismuth in various samples. Various factors affecting the electrode behavior were also investigated at the same time.     

双酚A在纳米二氧化铈修饰碳糊电极上的电化学行为及应用

采用固相合成法制备了纳米二氧化铈并对其进行了表征.研究了环境激素双酚A在CeO<,2>修饰碳糊电极上的电化学行为.在0.01 mol/L(pH 9.18)的硼砂溶液中,BPA于0.40 V处产生一不可逆的氧化峰,与裸碳糊电极相比,BPA在修饰电极上的电流响应明显增大,据此建立了测定塑料样品中BPA的线性扫描伏安法.线性...