MnCo<Subscript>2</Subscript>O<Subscript>4</Subscript> nanoparticles with excellent catalytic activity in thermal decomposition of ammonium perchlorate

MnCo₂O₄ spinel nanoparticles (NPs) have been prepared using Aloe vera gel solution. The characterization of prepared spinel was performed applying Fourier transform infrared spectroscopy, X-ray diffraction, Raman spectroscopy, transmission electron spectroscope, scanning electron microscope and dynamic light scattering. The results manifested that the prepared nanoparticles were mainly spherical plus minor agglomeration with average size distribution between 35 and 60 nm. The catalytic activity of the prepared nanoparticles upon thermal degradation of ammonium perchlorate (AP) was evaluated applying differential scanning calorimetry and thermogravimetry instruments. MnCo₂O₄ nanoparticles increased the released heat of AP from 450 to 1480 J g^?1 and decreased the decomposition temperature from 420 to 293 °C. The kinetic parameters obtained from Kissinger methods showed that the activation energy of AP thermal decomposition in the presence of MnCo₂O₄ NPs considerably decreased. Also, a mechanism has been proposed in the presence of catalyst for the process of thermal decomposition of AP.     

Investigation of catalytic activity of ZnAl<Subscript>2</Subscript>O<Subscript>4</Subscript> and ZnMn<Subscript>2</Subscript>O<Subscript>4</Subscript> nanoparticles in the thermal decomposition of ammonium perchlorate

A new powder metallurgy technique was developed in order to increase the reinforcement proportion of aluminum with two different fractions of Al₂O₃. Aluminum powders were mixed with 20 % vol of alumina particles as primarily reinforcement, and additional alumina was produced in situ as a result of reaction between Al and additional 7.5 % vol of Fe₂O₃ powder. The three grades of powders were milled and hot-pressed into small preforms, and differential scanning analysis (DSC) was performed to determine the kinetics of microstructural transformations produced on heating. DSC curves were mathematically processed to separate the superposing effects of thermal reactions. Transformation points on resulting theoretical curves evidenced two distinct exothermal reaction peaks close to the melting point of aluminum that were correlated with formation of Fe–Al compounds and oxidation of aluminum. Microstructural investigations by means of SEM-EDX and XRD suggested that these exothermal reactions produced complete decomposition of iron (III) oxide and formation of Fe–Al compounds during sintering at 700 °C, and therefore, heating at higher temperatures would not be necessary. These results, along with calculation of activation energies, based on Kissinger’s method, could be used to optimize the fabrication of Al-Al₂O₃ composites by means of reactive sintering at moderate temperatures.     

Synthesis and thermal decomposition of neodymium(III) peroxotitanate to Nd<Subscript>2</Subscript>TiO<Subscript>5</Subscript>

Neodymium(III) peroxotitanate is used as a precursor for obtaining Nd₂TiO₅. The last one possesses numerous valuable electrophysical properties. TiCl₄, Nd(NO₃)₃·6H₂O and H₂O₂ in mol ratio 1:2:10 were used as starting materials. The reaction ambience was alkalized to pH = 9 with a solution of NH₃. The obtained neodymium(III) peroxotitanate and intermediate compounds of the isothermal heating were proved by the help of quantitative analysis and infrared spectroscopy (IRS). It has Nd₄[Ti₂(O₂)₄(OH)₁₂]·7H₂O composition. The absorption band observed in IRS at 831 cm^?1 relates to a triangular bonding of the peroxo group of Ti, at 1062 cm^?1—terminal groups Ti–OH and at 1491 and 1384 cm^?1—the bridging OH^?-groups Ti–O(H)–Ti. Nd₂TiO₅ was obtained by thermal decomposition of neodymium(III) peroxotitanate. The isothermal conditions for decomposition were determined on the base of differential thermal analysis, thermogravimetric and differential scanning calorimetry results in the temperature range of 20–1000 °C. The mechanism of thermal decomposition of Nd₄[Ti₂(O₂)₄(OH)₁₂]·7H₂O to Nd₂TiO₅ was studied. In the temperature range of 20–208 °C, a simultaneous decomposition of the peroxo groups by the separation of oxygen and hydrate water is conducted and Nd₄[Ti₂O₄(OH)₁₂] is obtained. From 208 to 390 °C, the terminal OH^?-groups are separated and Nd₄[Ti₂O₇(OH)₆] is formed. In the range of 390–824 °C, the bridging OH^?-groups are completely decomposed to Nd₂TiO₅. The optimal conditions for obtaining nanocrystalline Nd₂TiO₅ are 900 °C for 6 h and 20–80 nm.     

TiO<Subscript>2</Subscript> nanofibers embedding single crystalline TiO<Subscript>2</Subscript> nanowires

Epitaxially grown titanium dioxide (TiO₂) nanofibers embedding single crystalline TiO₂ nanowires (NWs) were successfully fabricated by electropinning poly(vinyl pyrrolidone)/ethanol solutions mixed with hydrothermally synthesized TiO₂ NWs and titanium isopropoxide precursors and subsequently calcinating the electrospun nanofibers. Utilizing scanning electron microscopy (SEM) and transmission electron microscopy (TEM), the morphologies of TiO₂ NWs and nanofibers were investigated. High resolution TEM (HR-TEM) and selected area electron diffraction (SAED) allowed us to indentify the fact that, during the calcination process under the optimized condition, titanium isopropoxide precursors were epitaxially crystallized on the surface of single crystalline TiO₂ NWs. Based on the X-ray diffraction (XRD) experiments, it was also realized that the crystalline structure of hydrothermally synthesized TiO₂ NWs and epitaxially crystallized TiO₂ nanofibers is anatase and that TiO₂ composite nanofibers embedding TiO₂ NWs exhibited a higher crystallinity than the pristine TiO₂ nanofibers. Additionally, ultraviolet visible (UV–Vis) spectra of nanofibers indicated that optical properties of TiO₂ nanofibers can be tuned by introducing the single crystalline TiO₂ NWs.     

Nanosized TiO<Subscript>2</Subscript> particles decorated on SiO<Subscript>2</Subscript> spheres (TiO<Subscript>2</Subscript>/SiO<Subscript>2</Subscript>): synthesis and photocatalytic activities

Nanosized TiO₂ and nano-anatase TiO₂ decorated on SiO₂ spherical core shells were synthesized by using a sol–gel method. The synthesized pure TiO₂ nano particle and TiO₂ grafted on SiO₂ sphere with various ratios have been characterized for their structure and morphologies by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), Fourier transform infrared spectrophotometry (FTIR) and transmission electron microscopy (TEM). Their surface areas were measured using the BET method. The photocatalytic activity of all nanocomposites was investigated using methylene blue as a model pollutant. The synthesized TiO₂/SiO₂ particles appeared to be more efficient in the degradation of methylene blue pollutant, as compared to pure TiO₂ particles.     

Green synthesis of ZnCo<Subscript>2</Subscript>O<Subscript>4</Subscript> nanoparticles by <Emphasis Type=Italic>Aloe albiflora</Emphasis> extract and its application as catalyst on the thermal decomposition of ammonium perchlorate

This work aimed the evaluation of pH influence in the obtainment of composites from palygorskite (PAL) and chitosan (CS). The materials PAL/CS-1 and PAL/CS-2 were obtained by similar methodology with modified pHs: 5.0 ± 0.5 and 11.0 ± 0.5, respectively. Both materials were evaluated for specific surface area analysis, elemental analysis, XRD, FTIR, thermal analysis, MEV and interaction drug composite, using 5-aminosalicylic acid (5-ASA) as model. The surface area analysis data showed the reduction in PAL/CS-2 related to CS presence on surface in contrast with PAL/CS-1, which corroborate with elemental analysis present nine times more of CS in PAL/CS-2 composition. Regarding to XRD data, the interaction of CS with PAL did not cause modification in clay structure in PAL/CS-2. These results were confirmed by FTIR data with the N–H deformation vibration in PAL/CS-2 while PAL/CS-1 was invariable to PAL. In thermal analysis, results were observed 60.2% residual mass to PAL/CS-2, which it was lower than PAL (87.2%) and PAL/CS-1 (86.7%), due to CS decomposition which had enthalpy energy of 62.1 J g^?1 K^?1, confirming the data previously cited. PAL/CS-2 presented 5-ASA adsorption of 7.9 mg g^?1, which was inferior to others probably caused by scarcity of active sites of PAL already occupied by CS. These results showed that pH control was fundamental to enhance efficiency of obtainment of composite in basic pH because the decrease in CS protonation degree increasing interaction between this one and PAL, although it contributed to decrease in 5-ASA adsorption due to low availability of interaction sites.     

Dispersion state and catalytic properties of vanadia species on the surface of V<Subscript>2</Subscript>O<Subscript>5</Subscript>/TiO<Subscript>2</Subscript> catalysts

The dispersion state and catalytic properties of anatase-supported vanadia species are studied by means of X-ray diffraction (XRD), laser Raman spectroscopy (LRS), H₂ temperature-programmed reduction (TPR) and the selective oxidation of o-xylene to phthalic anhydride. The almost identical values of the experimental dispersion capacity of V₂O₅ on anatase and the surface vacant sites available on the preferentially exposed (001) plane of anatase suggest that the highly dispersed vanadium cations are bonded to the vacant sites on the surface of anatase as derived by the incorporation model. When the loading amount of V₂O₅ is far below its dispersion capacity, the dispersed vanadia species might mainly consist of isolated VO_x species bridging to the surface through V-O-Ti bonds. With the increase of V₂O₅ loading the isolated vanadia species interact with their nearest neighbors (either isolated or polymerized vanadia) through bridging V-O-V at the expenses of V-O-Ti bonds, resulting in the increase of the ratio of polymerized to isolated vanadia species and the decrease of the reactivity of the associated surface oxygen anions and, consequently, although the activity increases with loading to reach a maximum value, the turn over number (TON) of the V₂O₅/TiO₂ catalyst decreases linearly. When the loading amount of V₂O₅ is higher than its dispersion capacity, the turn over number decreases more rapidly with the increase of V₂O₅ loading due to the formation of V₂O₅ crystallites in which the oxygen anions associated with V-O-V bonds are less reactive and only partially exposed on the surface.     

Influence of ThO<Subscript>2</Subscript> on the photocatalytic activity of TiO<Subscript>2</Subscript>

Microcomposites consisting of TiO₂ (or Ce-doped TiO₂) and ThO₂ (0.5–2% of the TiO₂ mass) are produced by sol-gel synthesis of TiO₂ in presence of ThO₂. X-ray diffraction study reveals the effects of ThO₂ (compared to the ThO₂-free TiO₂, obtained by the same method) on the anatase interplanar distances, crystallites size and phase composition. The photocatalytic tests in presence of the composites under UV irradiation reveal an increase of the Malachite Green degradation rate constant. The effect depends on the Th relative content, temperature of annealing of the catalyst and addition of other doping agent. The highest photocatalytic activity is observed for TiO₂ obtained at 550°C and containing 1% ThO₂. The composite exhibits activity in dark, also. The presence of Ce⁴⁺ ions is not an obligatory requirement for the realization of the ThO₂ effect. The reported results suggest that the radioactivity of the Th and/or its decay products is one of the main factors responsible for the increased photocatalytic activity of TiO₂.      

The thermal decomposition of doped ammonium perchlorate

The thermal decomposition of ammonium perchlorate doped with Cu²⁺, Mn²⁺, Co²⁺ and Fe³⁺ (with and without H⁺) was studied using DTA and TG. Small concentrations of these ions inhibit the decomposition by eliminating the first exothermic peak. At higher concentrations, a catalyzed decomposition is observed. Either the influence of the doping ions on the mechanism of the thermal decomposition is different from that of added oxides or a modification of the electron transfer mechanism is needed.     

The effects of Co,Ni and Mn on the thermal processing of Zn<Subscript>2</Subscript>TiO<Subscript>4</Subscript> pigments

Summary  In this work, the thermodynamic activation and kinetic study of mineral lubricant oils was accomplished using isothermal and non-isothermal thermogravimetry based on mass loss as a function of time and temperature. The thermodynamic and kinetic behavior of the mineral lubricant oils depends on the atmosphere and heating rates used in TG analysis. The kinetic and thermodynamic results were satisfactory, presenting good correlation, with a linear correlation coefficient close to unit with a low standard deviation.     

Photooxidation of Ethylbenzene with TiO<Subscript>2</Subscript> and Metal Coated TiO<Subscript>2</Subscript> and its Kinetics

Summary. Photooxidation of ethylbenzene with oxygen to give ethylbenzene hydroperoxide has been achieved in a stirred photochemical reactor that was cooled by a water system by irradiation with a 400W high-pressure mercury lamp and using TiO₂ powder and metal coated TiO₂. The effects of the amount of copper or silver coated on TiO₂ and of the temperature on the rate of oxidation have been investigated. It is suggested that thermal cleavage of the O–O bond and photochemically generated singlet oxygen should be considered as the initiating step in a radical chain mechanism. An optimum loading of 6% Ag or 4–5% Cu was observed for photooxidation of ethylbenzene.     

Diagnostics of Plasma Behavior and TiO<Subscript>2</Subscript> Properties Based on DBD/TiO<Subscript>2</Subscript> Hybrid System

Plasma catalysis is gaining increasing interest in environmental and energy applications, such as the destruction of gas pollutants and hydrocarbon conversion. In order to further improve the application of plasma catalysis, it is crucial to understand the fundamental mechanisms, especially the mutual interaction between plasma and catalyst. In this paper, a parallel-plate dielectric barrier discharge (DBD) reactor is developed to investigate the plasma behavior and TiO₂ properties in the plasma/catalytic hybrid system. The introduction of TiO₂ thin film coated on the dielectric improves the discharge intensity, which significantly contributes to the enhancement of reactive species and charges. The energy efficiency of generating ozone in DBD/TiO₂ system has been approximately raised by 38% compared to pure DBD when the applied voltage reaches 13 kV. It is fortunately found that the discharge does not change the crystal structure of the TiO₂, but the band gap increases from 3.13 to 3.39 eV, which has been proved to enhance the oxidizability of TiO₂ in the degradation of methyl orange experiment under UV light. The FTIR and XPS spectra also demonstrate that N element is doped into the structure of TiO₂. These results successfully illustrate the plasma behavior and catalyst properties in plasma/catalysis hybrid system and provide reference for the optimization of the plasma catalysis process.     

The effect of pressure on the kinetics of thermal decomposition of ammonium perchlorate

Summary The kinetics of thermal decomposition of ammonium perchlorate at 230 and 260 are not changed under the influence of a pressure of 100 atm of an inert gas.Translated from Izvestiya Akademii Nauk SSSR, Seriya Khimicheskaya, No. 12 p. 2226–2227, December, 1964     

Non-isothermal kinetics of the thermal decomposition of sodium oxalate Na<Subscript>2</Subscript>C<Subscript>2</Subscript>O<Subscript>4</Subscript>

The thermal transformation of Na₂C₂O₄ was studied in N₂ atmosphere using thermo gravimetric (TG) analysis and differential thermal analysis (DTA). Na₂C₂O₄ and its decomposed product were characterized using a scanning electron microscope (SEM) and the X-ray diffraction technique (XRD). The non-isothermal kinetic of the decomposition was studied by the mean of Ozawa and Kissinger–Akahira–Sunose (KAS) methods. The activation energies (E _α) of Na₂C₂O₄ decomposition were found to be consistent. Decreasing E _α at increased decomposition temperature indicated the multi-step nature of the process. The possible conversion function estimated through the Liqing–Donghua method was ‘cylindrical symmetry (R₂ or F_1/2)’ of the phase boundary mechanism. Thermodynamic functions (ΔH*, ΔG* and ΔS*), calculated by the Activated complex theory and kinetic parameters, indicated that the decomposition step is a high energy pathway and revealed a very hard mechanism.     

Tantalum oxide effect on the surface structure and morphology of the IrO<Subscript>2</Subscript> and IrO<Subscript>2</Subscript> + RuO<Subscript>2</Subscript> + TiO<Subscript>2</Subscript> coatings and on the corrosion and electrochemical properties of anodes prepared from these

Alterations in the phase composition, porosity, and surface morphology of coatings are examined following the insertion of a quantity of Ta₂O₅ into active coatings prepared from IrO₂ or IrO₂ + RuO₂ + TiO₂ (OIRTA). It is shown that even an insignificant concentration of Ta₂O₅ in a coating renders it substantially amorphous and leads to the appearance of a large number of wide protracted cracks in the coating. The latter extends the surface of anodes and boosts their apparent catalytic activity in the chlorine evolution reaction. In addition, this accelerates the diffusion of chloride ions toward the front surface of anodes, which noticeably reduces the overvoltage of the chlorine evolution reaction when manufacturing sodium chlorate. The coatings’ amorphization and the development of their surface substantially reduce the corrosion resistance of these anodes as compared with OIRTA.     

Thermal behavior of Fe<Subscript>2</Subscript>O<Subscript>3</Subscript>/TiO<Subscript>2</Subscript> mesoporous gels

Summary Titania-based photocatalytic materials were prepared by sol-gel method using Fe³⁺ and polyethyleneglycol (PEG₆₀₀) as additives. Thermogravimetry (TG), differential thermal analysis (DTA) and evolved gas analysis (EGA) with MS detection were used to elucidate processes that take place during heating of Fe³⁺ containing titania gels. The microstructure development of the Fe₂O₃/TiO₂ gel samples with and without PEG₆₀₀ admixtures was characterized by emanation thermal analysis (ETA) under in situ heating in air. A mathematical model was used for the evaluation of ETA results. Surface area and porosity measurements of the samples dried at 120&deg;C and the samples preheated for 1 h to 300 and 500&deg;C were compared. From the XRD measurements it was confirmed that the crystallization of anatase took place after thermal heating up to 600&deg;C.     

Mechanism of thermal decomposition of zirconyl oxalate ZrOC<Subscript>2</Subscript>O<Subscript>4</Subscript>

Thermal decomposition of zirconyl oxalate hydrate was studied using DTA, TG, QMS and XRD techniques. It was shown that decomposition occurs in two stages: dehydration to anhydrous oxalate and next, decomposition to zircon oxide (zirconia). These steps are not well separated. We observed that significant amount of water are released during second stage of decomposition. Zircon dioxide is obtained in tetragonal form. Moreover, we consider some dependences between conditions of preparations zirconyl oxalate hydrate and some properties of solid product of its decomposition. Although the reaction of thermal decomposition of zirconyl salts is generally utilized in technology, many aspects of this process are still not sufficiently explained. In our work, we present some new interesting observations concerning thermal behaviour of zirconyl oxalate.     

Effect of TiO<Subscript>2</Subscript> surface modification in Rhodamine B photodegradation

Commercial TiO₂ nanoparticles were superficially modified through polymeric resins obtained from polymerization of citrate complexes of Y³⁺ and Al³⁺ with ethylenglycol. The materials were treated at 450 °C for 4 h to obtain modified nanoparticles, which were characterized by HR-TEM, Zeta potential and surface area through N₂ fisisorption. Rhodamine B photodegradation by visible light irradiation and in presence of those modified nanoparticles was compared with the same process in presence of unmodified commercial TiO₂ nanoparticles. It was observed, by UV–visible spectroscopy, that the catalytic photoactivity in presence of modified nanoparticles was smaller than that observed with commercial TiO₂ nanoparticles. However, the surface modifier played an important role in the photodegradation kinetic process, showing a non-linear relation between modifier amount and photodegradation rate, presenting a maximum value at 0.8% (w/w).     

Quantum-chemical study of adsorption of Ag<Subscript>2</Subscript>, Ag<Subscript>4</Subscript>, and Ag<Subscript>8</Subscript> on different parts of the TiO<Subscript>2</Subscript> surface

Quantum-chemical study of the adsorption of two-, four- and eight-atomic silver clusters on stoichiometric and partially reduced rutile (110) surface, and of silver tetramer on the surface of anatase (101) was carried out in the framework of periodic DFT model. The most energetically favorable positions of clusters on the surface of TiO₂ and the mechanism of binding the clusters with the substrate were revealed. According to the calculations, the adsorption of silver clusters on the surface of stoichiometric rutile (110) is more preferable than on the partially reduced one. The mechanism of binding the clusters with the surface of anatase and rutile is shown to be similar.