Quantitative determination of diethylene glycol contamination in pharmaceutical products

A simple, rapid, and reliable method was developed for the quantitative determination of diethylene glycol (DEG) in pharmaceutical products using capillary gas chromatography with flame ionization detection. The method uses ethylene glycol as internal standard and allows for the separation of propylene glycol and DEG. The assay was linear in a DEG concentration range between 1.0 and 10.00 mg/mL, with coefficients of variation of 2.3-4.4% for the tested concentrations. Quantitation and detection limits, respectively, were 1.0 mg/mL and 0.15 mg/mL diethylene glycol. The method was used to analyze 3 pharmaceutical products possibly contaminated with diethylene glycol, of which one was suspected of causing intoxication and death in children. Infrared spectroscopy was used to confirm the identity of diethylene glycol. This analytical methodology is proposed for evaluation of pharmaceutical products containing glycols to prevent intoxication and for security level verification.     

Formation of diethylene glycol as a side reaction during production of polyethylene terephthalate

Polymers of poly(ethylene terephthalate) (PET) always contain a certain amount of incorporated diethylene glycol (DEG), substituting the incorporated glycol. DEG is formed in a side reaction during the ester interchange of dimethyl terephthalate (DMT) with ethylene glycol or during direct esterification of terephthalic acid with ethylene glycol, and to a smaller extent during the polycondensation of the low-molecular material. DEG is formed via an unusual type of reaction: ester + alcohol → ether + acid. Some evidence of this type of reaction is given by the formation of dioxane in low molecular PET and of methyl Cellosolve and methyl carbitol during the ester interchange of DMT with ethylene glycol and diethylene glycol, respectively. The strongest support for this type of reaction, however, was obtained from kinetic data. Polyesters of low molecular weight with OH group contents ranging from 3 to 0.5 mole/kg were heated at 270°C in sealed tubes for 1–7 hr. The kinetic equation for the proposed reaction is: d[DEG]/dt = k[OH] [ester]. With the aid of one rate constant the formation of DEG in all esters could be described.     

Nuclear magnetic relaxation and phase transitions of diethylene glycol in Vycor porous glasses

The times of longitudinal T ₁ and transverse T ₂ magnetic relaxation of protons of diethylene glycol in the bulk phase and in Vycor porous glasses with average pore radii of 4, 11, and 32 nm are measured by the pulse NMR method in the 172–350 K temperature range. It is found that, for all samples of porous glasses, the crystallization of diethylene glycol is not observed if its content corresponds to the monolayer surface filling. The minimum content of diethylene glycol, which makes it possible to cause its crystallization in porous glass, is determined. By analyzing the dependence of the characteristics of a component with T _2b = 20−40 μs in the transverse magnetization decay on the content of diethylene glycol in porous glasses, the volume of nanopores comparable in size with diethylene glycol molecule is estimated.     

气相色谱-质谱法快速测定牙膏中的二甘醇

建立了气相色谱-质谱法（GC-MS）快速测定牙膏中的二甘醇的方法。牙膏样品经三氯甲烷提取后,应用气相色谱-质谱联用仪,以选择离子监测（SIM）模式对其中的二甘醇进行分析。二甘醇的线性范围为21.24-1062 mg/L,线性相关系数（r）为0.9995;检出限和定量限分别为2.0、5.0 mg/L;高、中、低3种浓度下的回收率在88.51%-101.6%之间,相对标准偏差（RSD）在1.6%-8.11%之间;仪器对二甘醇的响应在24 h内保持稳定。     

Catalysis of heteropoly acidic salts for synthesis of diethylene glycol ethyl ether with diethylene glycol and ethanol

Ag₃PW₁₂O₄₀ and Ag₄SiW₁₂O₄₀ showed high activity and stability in the synthesis of diethylene glycol ethyl ether with diethylene glycol and ethanol, on which the conversion is 80.2% and 78.4%, respectively, and the selectivity of diethylene glycol ether is 75.4% and 80.6%, respectively. After the third reaction cycle, Ag₃PW₁₂O₄₀ and Ag₄SiW₁₂O₄₀) still showed higher activity and selectivity, on which the conversion is 72. 6% and 77.5% respectively. But the activity of Ag₃PMo₁₂O₄₀ is lower, the conversion is only 21.0%. IR, XRD, TG and n‐butylamine titrimetry showed that the catalysis may be connected with two kinds of acidic centers owned by heteropoly acidic salt.     

Excess molar volumes of binary mixtures of γ-butyrolactone and a glycol at 303.15 K

Excess molar volumes at 303.15 K for the binary mixture of ethylene glycol+, diethylene glycol+, triethylene glycol+ and tetraethylene glycol+ γ-butyrolactone were determined from precise density measurements over the whole mole fraction range. The excess molar volumes are positive over the whole mole fraction range for ethylene glycol and diethylene glycol systems. For triethylene glycol and tetraethylene glycol systems, V^E curves are sigmoid with a positive lobe at low mole fraction of glycol and a negative lobe at high mole fraction. The excess molar volumes V^E, results are interpreted qualitatively in terms of several opposing effects.     

Viscosity of binary mixtures of 2-ethoxyethanol with ethylene glycol,diethylene glycol,triethylene glycol and tetraethylene glycol systems at T = (293.15, 298.15 and 303.15) K

Viscosities, at T = 293.15, 298.15 and 303.15 K, in the binary mixtures of 2-ethoxyethanol with ethylene glycol, diethylene glycol, triethylene glycol and tetraethylene glycol have been measured as a function of composition. From the experimental data the deviations in the viscosity have been calculated. The viscosity data, at T = 298.15 K, were correlated with equations of Hind et al., Grunberg and Nissan, and Frenkel. The results are discussed in terms of intermolecular interactions and structural properties of studied binary mixtures.     

Relative permittivity of the binary mixtures of 2-methoxyethanol with diethylene glycol,triethylene glycol,tetraethylene glycol,and polyethylene glycol 200 at various temperatures

Relative permittivities at T = (293.15, 298.15, and 303.15) K in the binary liquid mixtures of 2-methoxyethanol with diethylene glycol, triethylene glycol, tetraethylene glycol, and polyethylene glycol 200 have been measured over the entire mixture compositions. The relative permittivity deviations (Δε) were calculated from these experimental data. The results are discussed in terms of intermolecular interactions and structure of studied binary mixtures.     

Determination of vanadium by atomic absorption spectrophotometry

Methods for the determination of vanadium, in the range 0.5–100 mg/l, by atomic absorption spectroscopy in an oxy-acetylene as well as in a nitrous oxideacetylene flame are presented. For use with oxy-acetylene flames, vanadium is extracted as vanadium cupferrate into a mixture of methyl isobutyl ketone and oleic acid (78:22, v/v) and the organic phase is aspirated to the flame. The sensitivity is 0.7 mg/l of vanadium in the organic phase. For nitrous oxide-acetylene flames, an aqueous solution of vanadium is aspirated directly. The sensitivity is further improved by the use of methyl isobutyl ketone, the addition of Al³⁺ and diethylene glycol diethyl ether. Many potential interferences were examined and methods to overcome those found are given.     

Conductance behaviour of HCl in water-ethylene glycol, water-diethylene glycol and ethylene glycol-diethylene glycol mixtures

The conductance behaviour of HCl in water-ethylene glycol, water-diethylene glycol and ethylene glycol-diethylene glycol mixtures was investigated in the complete range of solvent compositions of 25°C by applying the three-parameter conductance equation. No appreciable association of the acid was observed in any of the mixed solvents. The large decrease ofΛ ₀ andΛ ₀ η ₀ of the acid in the early and end composition region of the mixed solvents has been attributed to the drastic structural changes brought about by the addition of the organic component in the aqueous solvent mixtures and by the addition of diethylene glycol in the case of ethylene glycol-diethylene glycol mixtures.     

Simultaneous determination of diethylene glycol and propylene glycol in pharmaceutical products by HPLC after precolumn derivatization with p-toluenesulfonyl isocyanate

A simple and reliable HPLC method was developed for the simultaneous quantitative analysis of diethylene glycol (DEG) and propylene glycol (PG) in pharmaceutical products by precolumn derivatization. The derivatization reagent p-toluenesulfonyl isocyanate (TSIC, 10 microL, 20% in ACN v/v) was added to 100 microL of the sample, and then 10 muL of water was added. The resulting derivatives were separated using a C(18)analytical column and a mobile phase composed of 0.01 M KH(2)PO(4)buffer (adjusted to pH 2.5 with phosphoric acid) and ACN (47:53 v/v) at 1 mL/min and 25 degrees C. For detection, UV light at 227 nm was used. The derivatization conditions including reaction time, temperature, and concentration of TSIC were optimized. The calibration curves were linear from 0.062 to 18.6 microg/mL (r(2)= 0.9999) and from 0.071 to 21.3 microg/mL (r(2) = 0.9999) for DEG and PG, respectively. The RSD values of intra- and interday assays were all below 4% for DEG and PG. The proposed method was then successfully applied to analyze two Armillarisin A injection samples and two spiked syrup samples.     

Investigation of the formation of poly(ethylene terephthalate) with model molecules. IV. Catalysis of the esterification of ethylene glycol with benzoic acid and of the condensation of ethylene glycol monobenzoate

The esterfication of ethylene glycol (EG) with benzoic acid (BA) is an acid-catalyzed reaction which leads, as a first intermediate, to ethylene glycol monobenzoate (EGMB). This compound has an ? OH group which is more active towards carboxylic groups than the first ? OH group of EG. Moreover, it is a key intermediate in the formation of sideproducts containing diethylene glycol (DEG) moieties. The condensation reaction of EGMB was particularly studied in the presence of carboxylic acids or metal derivatives as catalysts. Titanium is the most active. Sb, which is widely used in the industrial synthesis of PET, needs to be present at a high level of concentration to show an activity. The presence of carboxylic groups in the reaction medium does not affect its activity, but it is necessary to remove the ethylene glycol as soon as it is formed in order to keep it active during the condensation reaction.     

Viscosimetric and ultrasonic studies of intermolecular interactions of 2-methoxyethanol with diethylene glycol,triethylene glycol and tetraethylene glycol binary mixtures

The viscosities at T = (293.15, 298.15 and 303.15) K and ultrasonic speeds at T = 298.15 K in the binary liquid mixtures of 2-methoxyethanol with diethylene glycol, triethylene glycol and tetraethylene glycol have been measured over the entire mixture compositions. From the experimental data, deviations in the viscosity (Δη), ultrasonic speed (Δu), and excess energies of activation for viscous flow (ΔG* ^E ) have been calculated. The viscosity data were correlated with equations of Hind et al., Grunberg and Nissan, Frenkel, and McAllister. The results are discussed in terms of intermolecular interactions and structure of studied binary mixtures.     

网络型聚醚酯弹性体聚柠檬酸二甘醇酯的合成与性能

用一缩二乙二醇(二甘醇)和柠檬酸通过熔融缩聚的方法,合成了一种新型的网络型聚醚酯弹性体—po-ly(diethylene glycol citrate)(PDGC).用FTIR初步表征了预聚物的结构;通过ATR-FTIR、DSC、XRD等表征了PDGC的结构;测试了材料的静态水接触角、力学性能以及体外降解性能,考察了单体的摩尔比以及后期交联时间对材料上述性能的影响.     

火焰原子吸收分光光度法测定五氧化二钒中铁及氧化钾、氧化钠含量

五氧化二钒样品用盐酸分解,在稀盐酸介质中,用原子吸收分光光度计分别于248.3,766.5,589.0 nm波长处,使用空气–乙炔火焰,测量五氧化二钒中铁及氧化钾、氧化钠含量。在最佳实验条件下,铁、氧化钾、氧化钠的质量浓度分别在0.05~0.20,0.05~0.80,0.20~1.0 mg/L范围内与吸光度线性关系良好,相关系数分别为0.998 6,0.994 3,0.994 2。方法检出限铁为6.7μg/L,氧化钾为1.0μg/L,氧化钠为1.4μg/L,加标回收率为95.9%~103.0%。铁、氧化钾、氧化钠测定结果的相对标准偏差分别为3.2%,4.2%,2.9%(n=6)。该方法适合五氧化二钒中铁及氧化钾、氧化钠的测定。     

Tetrabutylammonium hydrogen sulfate catalyzed eco-friendly and efficient synthesis of glycosyl 1,4-dihydropyridines

An efficient and eco-friendly synthesis of glycosyl 1,4-dihydropyridines has been achieved by a three-component reaction of β-keto esters or ketones, enamines and glycosyl aldehydes in the presence of tetrabutylammonium hydrogen sulfate as catalyst in diethylene glycol.     

Quantitation of diethylene glycol monoethyl ether in citrus oils

The use of diethylene glycol monoethyl ether as a flavor solvent is restricted. Since existing methods of quantitation are tedious or require sophisticated multi-dimensional GC instrumentation, a simple method has been developed using low cost GC-MS. Monitoring of ions 31 and 45 enables quantitation of DEGEE in essential oils at levels down to 1 μg/g with accuracy equal to or better than 15%.     

Thermal reactivities of potassium and cadmium hydrogenhexavanadates

The thermal reactivities of KHV₆O₁₆·3H₂O and Cd(HV₆O₁₆)₂·12H₂O were investigated. By means of IR spectroscopy and X-ray phase analysis it was found that, after dehydration, both compounds decompose to vanadium pentoxide and the corresponding metavanadate. Potassium metavanadate and vanadium pentoxide react together to form bronzes of different compositions. In contrast, vanadium pentoxide and cadmium metavanadate are the predominant components of the reaction products obtained within the temperature range from 300° to 800°C.     

Kinetics of poly(ethylene terephthalate) glycolysis by diethylene glycol. I. Evolution of liquid and solid phases

The kinetics of uncatalysed glycolysis, at 220 °C, of poly(ethylene terephthalate) (PET) by diethylene glycol (DEG) in high excess has been studied. An experimental device allowing good separation, at reaction temperature, of the solid and liquid phases was set up.The results suggest that PET is initially depolymerized in the slightly swollen solid phase, by glycolysis of the amorphous interlamellar chains. This mechanism continues until a solid phase of highly crystallized polyester is obtained.The internal tensions engendered by this chemical modification cause cracks, delamination and mechanical disintegration of the polymer. The transfer towards the liquid phase is then strongly accelerated and the solvolysis of the depolymerization products continues in the liquid phase, up to equilibrium.     

Thermophysical properties of binary liquid mixtures of polyether and n-alkane at 298.15 and 323.15 K: heat of mixing,heat capacity,viscosity, density and thermal conductivity

An apparatus for a rapid and simultaneous determination of the thermophysical properties excess enthalpy, isobaric heat capacity, kinematic viscosity, density and thermal conductivity has been developed. The experimental setup is subject of this paper. At 298.15 and 323.15 K, the systems ethylene glycol dimethyl ether–n-dodecane, diethylene glycol dimethyl ether–n-dodecane, triethylene glycol dimethyl ether–n-dodecane, tetraethylene glycol dimethyl ether–n-dodecane and diethylene glycol dibutyl ether–n-dodecane have been investigated. The experimental results are correlated and the macroscopic properties are interpreted.