Measurements of relative thick target yields for PIGE analysis on light elements in the proton energy interval 2.4–4.2 MeV

In order to extend the energy range of the systematic investigation on relative thick target yields performed by ANTTILA et al² for 1E_p2.4 MeV bombarding energies, gamma spectra and yield data are presented for elements Z=3–9, 11–17, 19–21 in the energy range 2.4E_p4.2 MeV and the results are discussed from the point of view of PIGE analysis.     

A toxic reagent-free method for normal-phase matrix solid-phase dispersion extraction and reversed-phase liquid chromatographic determination of aldrin,dieldrin, and DDTs in animal fats

A method for the determination of aldrin, dieldrin, DDT, DDE, and DDD contamination in animal fats (beef tallow, lard, and chicken fat) without using toxic reagents is developed, that uses high-performance liquid chromatography after the sample has been prepared by matrix solid-phase dispersion (MSPD) with acidic alumina oxide. A reversed-phase C₁-silica column with a mobile phase of 50% (v/v) ethanol solution (in water) and a photo-diode array detector were used for the determination. Average recoveries of the target compounds (0.2–5.0 g g^–1) ranged from 84–98%, with coefficients of variation of <5%. The limits of quantitation were 0.16 g g^–1 for AD, 0.10 g g^–1 for DD, 0.06 g g^–1 for DDT, 0.07 g g^–1 for DDE, and 0.05 g g^–1 for DDD. No toxic reagents were used at all.     

The relative permittivity of 1,2-ethanediol+2-methoxyethanol+water ternary mixtures

The relative permittivities for the ternary 1,2-ethanediol (component 1) + 2-methoxyethanol (2) + water (3) solvent system have been measured for 66 mixtures covering the whole mole fraction composition 0X₁/X₂/X₃ 1 range at –10, –5 and 0 °C. The experimental data were used to test some empirical relations stating the dependence of = (X₁, X₂, X₃). A comparison between the calculated and experimental data show that these equations can be usefully employed to predict values in correspondence of the experimental data gaps.     

Mechanism of the oxidation of L-ascorbic acid by the bis(pyridine-2,6-dicarboxylate)cobaltate(III) ion in aqueous solution

A detailed investigation of the oxidation of L-ascorbic acid (H₂A) by the title complex has been carried out using conventional spectrophotometry at 510 nm, over the ranges: 0.010 [ascorbate] _T 0.045 mol dm^–3, 3.62 pH 5.34, and 12.0 30.0 °C, 0.50 I 1.00 mol dm^–3, and at ionic strength 0.60 mol dm^–3 (NaClO₄). The main reaction products are the bis(pyridine-2,6-dicarboxylate)cobaltate(II) ion and l-dehydroascorbic acid. The reaction rate is dependent on pH and the total ascorbate concentration in a complex manner, i.e., k _obs = (k ₁ K ₁)[ascorbate] _T /(K ₁ + [H⁺]). The second order rate constant, k ₁ [rate constant for the reaction of the cobalt(III) complex and HA^–] at 25.0 °C is 2.31 ± 0.13 mol^–1 dm³ s^–1. H = 30 ± 4 kJ mol^–1 and S = –138 ± 13 J mol^–1 K^–1. K ₁, the dissociation constant for H₂A, was determined as 1.58 × 10^–4 mol dm^–3 at an ionic strength of 0.60 mol dm^–3, while the self exchange rate constant, k ₁₁ for the title complex, was determined as 1.28 × 10^–5 dm³ mol^–1 s^–1. An outer-sphere electron transfer mechanism has been proposed.     

Surface Properties of Nickel Electrodes in an Alkaline Electrolyte: An Ellipsometry Study

Adsorption of oxygen-containing species (OCS) on a polycrystalline nickel electrode in an alkaline electrolyte is studied by electrochemical and ellipsometric methods in the potential region from hydrogen evolution to oxygen evolution. It is concluded that OCS have stoichiometric composition Ni(OH)₂ up to 1.35 V. The potential of the OCS formation onset, the oxide monolayer thickness, and the surface coverage by OCS in the interval 0 1 are determined. The oxidation and reduction of a nickel oxide layer, repeatedly cycled at 1.35–1.5 V, suggests that this process is chemically reversible and the thickness of the oxide formed at 1.35 V is constant. It is shown that keeping the electrode under open-circuit conditions at 0.7–0.9 V for 10–20 h leads to the formation of nonelectroconducting oxide NiO _z .     

Ionic strength dependence of formation constants. Part 4. Potentiometric study of the system Cu2+-Ni2+-citrate

Summary The ternary Cu²⁺-Ni²⁺-citrate (cit^3–) system was investigated potentiometrically in aqueous solution, at different temperatures, 10t45°C, and ionic strengths, 0.03I0.8 mol dm^–3, using potassium nitrate or tetraethylammonium bromide as background salt. Since the citrate anion forms weak complexes with potassium, the stability constants here reported differ according to whether the potassium association is considered or not. In the presence of both Cu²⁺ and Ni²⁺, the mixed metal species, [CuNi(cit)₂H_–2]^4– is formed with citrate in solution, in addition to the various binary complexes. We have obtained the dependence for all the formation constants on ionic strength and temperature. The previous suggestions concerning a general equation for describing the dependence, log =f(I), are confirmed; from the study of log =f(T) we have obtained the values of thermodynamic parameters. The dependence of H on ionic strength is discussed.     

Determination of Total Selenium Content in Cereals and Bakery Products by Flow Injection Hydride Generation Graphite Furnace Atomic Absorption Spectrometry Applying in-situ Trapping on Iridium-Treated Graphite Platforms

A flow injection hydride generation graphite furnace atomic absorption spectrometric (FI-HG-GFAAS) method was applied to the determination of Se in Se-doped and undoped cereals and bakery products. For the purpose of doping, the soils used for the cultivation of the cereals were dosed with Se-doped foliar fertilizers. The samples were dissolved in a mixture of HNO₃ and H₂O₂ solutions using microwave-assisted digestion. The decomposition of H₂Se generated from the sample solutions and the trapping of elemental Se were performed at a temperature of 300°C on an Ir-pretreated integrated graphite platform of a transversally heated graphite atomizer (THGA). For release of the trapped Se within a fairly short atomization time (5s), an atomization temperature of 2200°C was observed to be optimal. The overall efficiency of hydride generation, transport and trapping was 86%.The upper limit of the linear dynamic range of calibration was 10µgL^–1, which corresponds to 0.5µgg^–1 for solid samples. Recovery of the samples spiked with Se^VI solutions was found to be 93±6% on average. The relative standard deviation of the determinations was less than 8%. The limit of detection was found to be 0.06µgL^–1, corresponding to 3ngg^–1 for solid samples. The accuracy of the method was verified with the use of IAEA-155 (whey powder) certified reference material. End-capped THGA tubes resulted in an extension of the linear calibration range compared to that of standard THGAs.The Se content in bakery products made of undoped cereals ranged from 7.7 to 68ngg^–1 (wet weight) in 18 samples, whereas the Se content of the corresponding cereals was found to be below 100ngg^–1 (wet weight). The Se level of cereals grown on soils treated with Se-doped fertilizers ranged from 128 to 1046ngg^–1 (wet weight), and it depended linearly on the Se concentration of the corresponding foliar fertilizer.     

Difference FTIR spectroscopy of folded phonons in Si/Si1−xGex superlattices

A home-made slow-scan Fourier spectrometer was adapted in the far infrared (10–100 cm^–1) to investigate strained-layer Si/Si_0.5Ge_0.5 superlattices (=SLs) with modulation periodsD=120 Å, 40 Å at liquid helium temperature. The small variations of reflectivity (10^–3) were detected against the large background by modulating the temperature of the sample using a chopped near infrared light emitting diode. The resulting change of sample temperature causes a variable population of the lowest acoustic phonon branch to largerq-values, and a large fraction of the zone folded phonon dispersion (q/D) can be measured by observing difference phonon processes. The measurements outline important SL-properties (modulation periods, phonon dispersion, interface quality and strain effects). X-ray diffraction analysis confirms the FTIR-results.     

Voltammetric Behavior of Dopamine at ct-DNA Modified Carbon Fiber Microelectrode

A sub-micrometer thin-layer DNA modified carbon fiber microcylinder electrode was prepared by electrodeposition of ct-DNA at 1.5V (vs. Ag/AgCl). The voltammetric behavior of dopamine (3-hydroxytyramine) was investigated at the modified electrode. It was found that the modified electrode exhibits a highly electrocatalytic activity toward dopamine oxidation. Differential pulse voltammetry was used for determination of dopamine in pH 7.4 phosphate buffer solution. A linear response of the peak current versus the concentration was found in the range of 4×10^–6 to 10^–4molL^–1 at 10^–4molL^–1 AA (ascorbic acid) coexistence (R=0.9959) and the range of 6×10^–5 to 10^–3molL^–1 at 10^–3molL^–1 AA (R=0.9960). The presence of a high concentration of ascorbic acid did not interfere with the determination. The proposed method exhibited good recovery and reproducibility. This method can be applied to the detection of DA in real samples.     

Spectrophotometric Determination of the Polyiodohalides of Organic Nitrogen-Containing Cations

The following biologically active diiodohalides of organic cations were studied: N-cetylpyridinium, trimethylbenzylammonium, triethylbenzylammonium, and N,N-dimethylmorpholinium diiodochlorides; N-cetylpyridinium, tetramethylammonium, tetrabutylammonium, and N,N-dimethylmorpholinium diiodobromides; and N,N-dimethylmorpholinium and butyroylcholinium triiodides. A simple and rapid procedure was proposed for the determination of the above compounds; it is based on the conversion of organic diiodohalides into the corresponding triiodides (_{300 nm} 4 × 10⁴; _{370 nm} 2 × 10⁴) in the presence of excess potassium iodide (RSD 2%). An extraction–spectrophotometric method was developed for the quantitative determination of the biologically active compounds in pharmaceutical dosage forms based on their ion associates with anionic dyes, erythrosine (m _min = 1.25–3.30 g; RSD 3%) and Bromothymol Blue (m _min = 3.85 g; RSD = 3%), or a cationic dye—1,3-dimethyl-2-(4-morpholinophenyl)azobenzimidazolium phenylsulfate (m _min = 2.32–8.26 g; RSD 4%). The developed procedures were used for monitoring drug substances in model pharmaceutical preparations (RSD 4%).     

Withasteroids ofPhysalis. V. A study of the1H and13C NMR spectra of the withasteroids visconolide and 28-hydroxywithaperuvin C

The PMR and¹³C NMR spectra of new withasteroids — visconolide and 28-hydroxywithaperuvin C, isolated fromPhysalis viscosa L. — have been investigated. A detailed analysis of the spectral characteristics obtained is given. For visconolide is proposed the structure of 4,12,17,28-pentahydroxy-1-oxo-5, 6-epoxy-22R-witha-2,24-dienolide, and for 28-hydroxywithaperuvin C that of 6,14,17,20R, 28-pentahydroxy-l-oxo-22R-witha-2, 4, 24-trienolide.Institute of the Chemistry of Plant Substances, Academy of Sciences of the Uzbek SSR, Tashkent. Translated from Khimiya Prirodnykh Soedinenii, No. 5, pp. 657–663, September–October, 1985.     

Kinetic and mechanistic studies on the oxidation of arginine and histidine by chloramine-T in hydrochloric acid medium

The oxidation of amino acids by chloramine-T (CAT) in HCl medium at 30°C indicates simultaneous catalysis by H⁺ and Cl^– ions in the HCl concentration range of 0.04–0.12 M. The reaction is first order with respect to concentrations [CAT], [H⁺] and [arginine], but zero order with respect to [histidine]. The rate depends also on Cl^– concentration following 0.7th order. At HCl concentrations >0.12 M, the rate equation is:w=k[CAT] [amino acid]^0.6 and is independent of the [Cl^–]. A suitable mechanism has been suggested.

---

-T (CAT) HCl (30°C) H⁺, Cl^– [HCl]=0,04–0,12M. [CAT], [H⁺] [] []. [Cl^–]^0,7. [HCl]>0,12M =k · [CAT][]^0,6 [Cl^–]. .

     

Solvent Effect on the Thermodynamics of Complex Formation with Proton Transfer from 4-Nitrophenylnitromethane to Triethylamine

In studying the thermodynamics of the formation of the 4-nitrophenylnitromethane–triethylamine ion pair in different chemical solvents within the dielectric constant interval 2.4 65, an increase in the ion pair stability with an increase in the medium polarity is revealed. Account for the effect of dielectric saturation of solvent molecules through the Blok–Walker function () gives pK= f(()) (Kis the equilibrium constant of ion pair formation), which is nearly linear. The electrostatic and nonelectrostatic components of the thermodynamic parameters of the reaction are estimated. The governing role of the covalent contribution to solvents with high polarity and of the electrostatic contribution to systems with 4–7 is established. A linear correlation between the bathochromic shift of the band in the electronic absorption spectra of solutions of the ion pair and the logarithm of the stability constant of the complex is found.     

Indirect Determination of Sulfide by Cold Vapor Atomic Absorption Spectrometry

A method for the determination of sulfide based on its interference with the determination of Hg by cold vapor atomic absorption spectrometry is described. The decrease in mercury absorbance at 253.7nm is proportional to the concentration of sulfide over the range of 10–320ngmL^–1. The limit of detection was found to be 7ngmL^–1 and the relative standard deviation (R.S.D.) for the determination of different concentrations of sulfide was in the range of 1.8–2.2%. This method was applied to the determination of sulfide in whole human blood after gas-phase separation.     

Effect of the state of vanadium cations on the IR spectra of adsorbed carbon monoxide

ESR and IR-spectrosocpic studies of the effect of the state of vanadium ions on the IR-spectra of adsorbed CO have revealed complex formation of CO with V⁴⁺ (vCO at 2192 and 2205 cm^–1) and V³⁺ (vCO at 2178 and 2185 cm^–1) ions.

---

-- - CO. CO V⁴⁺ (vCO 2192, 2205 cm^–1) V³⁺ (vCO 2178, 2185 cm^–1).

     

Transformations of formaldehyde and glycolaldehyde during the hydroformylation of formaldehyde in the presence of rhodium catalysts

Hydroformylation of formaldehyde to give glycolaldehyde (GA) in the presence of RhCl(PPh₃)₃, RhCl(CO)(PPh₃)₂, or the RhCl₃ + PPh₃ system inN,N-dimethylacetamide was studied. The hydroformylation is accompanied by the Cannizzaro-Tishchenko reaction, condensation of CH₂O with GA to give C₃-C₁₆ polyoxyaldehydes (POA), and dimerization of GA. The formation of POA, which probably occurs through coordination of GA with a Rh atom, predominates among the side reactions. The optimum conditions for hydroformylation of CH₂O were found to be: RhCl₃ + PPh₃ as the catalyst,T 383 K, 12MPa, [H₂O] 1.8 mol L^–1, [Rh] 2.5 · 10^–3 g-at. L^–1, and [CH₂O] 0.03 g L^–1. At a substrate conversion of 62–67 %, the selectivity of GA formation reaches 96 %, and the yield is 60–65 %.Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 1, pp. 75–78, January, 1995.     

An investigation of micro-brownian motions in polydimethylsiloxane by complementary incoherent-neutron-scattering and nuclear-magnetic-resonance experiments below room temperature

Two different experimental methods, neutron scattering and nuclear magnetic resonance are used to investigate the random methyl group and segmental rotational jump motions in polydimethylsiloxane. It is shown that nuclear magnetic relaxation and line width experiments are complementary to incoherent neutron scattering fixed-window experiments, the principle of the fixed-window experiments being discussed in somewhat detail. Satisfactory agreement of these experimental techniques is achieved as to the determination of the two model parameters of the motional processes in question, i. e. the activation energy and the preexponential factor of the Arrhenius ansatz made for the correlation time or jump time, respectively.Contribution partly presented during the meeting of the Macromolecular Club, June 8–10, 1983 in Uppsala, the spring conference of the Deutsche Physikalische Gesellschaft, March 12–17, 1984 in Münster and the Fourth International Seminar on Polymer Physics, October 22–26, 1984 in Eyba (GDR).     

Phase Equilibria in the System CuO-Fe2O3-Sb2O4-O2

Results of X-ray phase analysis were used to construct the phase diagram of the system CuO-Fe₂O₃-Sb₂O₄-O₂ at 1000°C in air. Two Cu_2x Fe_4-3x Sb _x O₆ solid solutions (0 x 0.154 and 0.923 x 1) of, respectively, hematite and bixbyite structure were identified.     

Ammoxidation of 3- and 4-picolines over V2O5?SnO2/γ?Al2O3 catalyst

The ammoxidation of 3- and 4-picolines has been studied over V₂O₅–SnO₂/–Al₂O₃ catalysts prepared by surface impregnation technique. Best results were obtained for the generation of cyanopyridines in the temperature range 400–450°C and sub-stoichiometric value with respect to O₂. Catalysts that were calcined above 700°C showed no activity.

---

3- 4- V₂O₅–SnO₂/–Al₂O₃, . 400–450°C O₂. , 700 K, .