Success and failure with phthalate buffers in capillary zone electrophoresis

Phthalate buffers are currently used in capillary electrophoresis as robust electrolyte systems for indirect detection. This contribution demonstrates that these buffers show regularly not only successful regions of mobilities of analytes (sample window) but also regions of failure where the migration of analytes is strongly deteriorated due to the presence of a system zone. System zones in phthalate buffers may be easily detected by UV detection and manifest themselves as peaks or dips. Peak shape diagrams are advantageously used for the prediction of the migration behavior of system zones in phthalate background electrolyte (BGE) systems at various pH. It is shown that the mobility of the system zone varies strongly with pH, is practically zero at pH values below 4 and above 7, and shows a maximum at pH 5. Thus, the system peak may coincide either with the peaks of various analytes or with the electroosmotic flow (EOF) peak. Experiments are given showing the effects of such coincidences as, e.g., zigzag detection patterns, double EOF peaks, and/or unusually broad peaks/dips. The message of this contribution is to show how to understand the electrophoretic properties of phthalate BGEs that, regardless of possible failure regions, may be successfully used in the analytical practice of capillary zone electrophoresis (CZE).     

Conductivity detection in capillary zone electrophoresis: inspection by PeakMaster

A simple rule stating that the signal in conductivity detection in capillary zone electrophoresis is proportional to the difference between the analyte mobility and mobility of the background electrolyte (BGE) co-ion is valid only for systems with fully ionized electrolytes. In zone electrophoresis systems with weak electrolytes both conductivity signal and electromigration dispersion of analyte peaks depend on the conductivity and pH effects. This allows optimization of the composition of BGEs to give a good conductivity signal of analytes while still keeping electromigration dispersion near zero, regardless of the injected amount of sample. The demands to achieve minimum electromigration dispersion and high sensitivity in conductivity detection can be accomplished at the same time. PeakMaster software is used for inspection of BGEs commonly used for separation of sugars (carbohydrates, saccharides) at highly alkaline pH. It is shown that the terms direct and indirect conductivity detection are misleading and should not be used.     

Application of self-organizing maps for the classification of chromatographic systems and prediction of values of chromatographic quantities

The separation of a complex mixture of inorganic and organic anions by ion chromatography–capillary electrophoresis using a cationic polymer added to the background electrolyte and indirect UV detection has been studied. The addition of unmodified polymer to an electrolyte suitable for indirect detection resulted in the appearance of a system peak due to the counter-anion on the polymer and while the position of the analytes relative to this system peak could be changed, this was found to be an unacceptable approach for mixtures of large numbers of analytes. Although conversion of the polymer to replace the counter-ion with the indirect UV detection probe ion simplified the system, this approach restricted the flexibility of the system because the probe and polymer concentration were necessarily linked. This limitation could be overcome by selecting the appropriate type of probe ion, with probes having a low ion-exchange selectivity coefficient providing greater retention of analytes than probes with a high ion-exchange selectivity coefficient. Three electrolyte systems with different probes (benzoate, chromate and phthalate) were modelled using a previously derived migration equation and this was used to optimise the electrolyte composition to enable the separation of a mixture of 24 inorganic and organic anions within 7 min. The electrolyte composition was then optimised for the analysis of anions in Bayer liquor with the final separation selectivity being substantially improved for selected key analytes.     

Sensitive indirect photometric detection of inorganic and small organic anions by capillary electrophoresis using Orange G as a probe ion

This study addresses the two major problems in the use of dyes as highly absorbing probes for indirect photometric detection in capillary electrophoresis (CE). First, effective electroosmotic flow (EOF) modification or suppression to allow separation and detection of a wide mobility range of analytes is not straightforward when electrolytes containing increased dye concentrations are used. The suppression of EOF to less than + 5x10(-9) m(2)V(-1)s(-1) was achieved with a combination of a poly(ethylenimine) (PEI)-coated capillary and the addition of the neutral polymer hydroxypropylmethylcellulose (HPMC) to the background electrolyte. Second, the deterioration of baselines due to adsorption of the dye probe to the capillary wall is generally a problem. In this work, baseline quality at higher probe concentrations was significantly improved by a rather unusual but highly effective combination of a simultaneous application of a slight overpressure (25 mbar) at the injection end during the separation, and the use of a relatively narrow capillary of 50 microm inner diameter. Both measures would appear to be counterproductive. Optimisation of the probe concentration with regard to signal-to-noise ratio resulted in an electrolyte of 4 mM Orange G, 0.05% HPMC buffered at pH 7.7 by the addition of 10.0 mM histidine isoelectric buffer. Very high separation efficiencies of 128 000-297 000 plates were made possible by the relatively high probe concentration. Combined with excellent detection sensitivity, even with the introduction of hydrodynamic flow and a reduced optical path length, these measures resulted in limits of detection ranging from 0.216 to 0.912 microM with a deuterium lamp light source (248 nm) and from 0.147 to 0.834 microM with a 476 nm blue light-emitting diode (LED) light source. Reproducibility over 30 consecutive runs without changing the electrolyte was excellent, with relative standard deviation (RSD) values of 0.14-0.80% for migration time, 1.27-3.36% for peak area and 0.88-5.12% for peak heights. The optimised electrolyte was used for the analysis of inorganic anions in air filter samples, providing good agreement with results obtained by ion chromatography.     

High-sensitive capillary zone electrophoresis analysis by electrokinetic injection with transient isotachophoretic preconcentration: electrokinetic supercharging

The principle of an on-line preconcentration method for capillary zone electrophoresis (CZE) named electrokinetic supercharging (EKS), is described and based on computer simulation the preconcentration behavior of the method is discussed. EKS is an electrokinetic injection method with transient isotachophoretic process, is a powerful preconcentration technique for the analysis of dilute samples. After filling the separation capillary with supporting electrolyte, an appropriate amount of a leading electrolyte was filled and the electrokinetic injection was started. After a while, terminating electrolyte was filled subsequently and migration current was applied. This procedure enabled the introduction of a large amount of sample components from a dilute sample without deteriorating separation. Computer simulation of the electrokinetic injection revealed that EKS was effective for the preconcentration of analytes with wide mobility ranges by proper choice of transient isotachophoresis (ITP) system and electroosmotic flow (EOF) should be suppressed to increase injectable amount of analytes under constant voltage mode. A test mixture of rare-earth chlorides was used to demonstrate the uses of EKS-CZE. When a 100 microL sample was used, the low limit of detectable concentration was 0.3 microg/L (1.8 nM for Er), which was comparable or even better than that of ion chromatography and inductively coupled plasma-atomic emission spectrometry (ICP-AES).     

Polymeric ionic liquid as a background electrolyte modifier enhancing the separation of inorganic anions by capillary electrophoresis

A novel and easy method for the separation of inorganic anions by capillary electrophoresis using a polymeric ionic liquid (PIL), poly(1-vinyl-3-butylimidazolium bromide) as a background electrolyte modifier has been developed. The PIL has been proved to generate a reversed electroosmotic flow which reduces the analysis time and improves the separation significantly. Effects of the PIL concentration and buffer composition (pH and concentration) were evaluated on basis of the resolution and efficiency of the sample. Under optimum conditions, good separation of six model inorganic anions was achieved with high efficiency and excellent reproducibility within 3 min. The results obtained indicate that the combination of reversed EOF and the association between the analytes and the PIL on the capillary wall or BGE play a prominent role in the separation of anions. Therefore, the PIL presents a useful alternative for the BGE modifier in the study of inorganic anions by CE.     

Mobility-based selective on-line preconcentration of proteins in capillary electrophoresis by controlling electroosmotic flow

A simple method to perform selective on-line preconcentration of protein samples in capillary electrophoresis (CE) is described. The selectivity, based on protein electrophoretic mobility, was achieved by controlling electroosmotic flow (EOF). A short section of dialysis hollow fiber, serving as a porous joint, was connected between two lengths of fused silica capillary. High voltage was applied separately to each capillary, and the EOF in the system was controlled independently of the local electric field intensity by controlling the total voltage drop. An equation relating the EOF with the total voltage drop was derived and evaluated experimentally. On-line preconcentration of both positively charged and negatively charged model proteins was demonstrated without using discontinuous background electrolytes, and protein analytes were concentrated by approximately 60-200-fold under various conditions. For positively charged proteins, positive voltages of the same magnitude were applied at the free ends of the connected capillaries while the porous joint was grounded. This provided a zero EOF in the system and a non-zero local electric field in each capillary to drive the positively charged analytes to the porous joint. CE separation was then initiated by switching the polarity of the high voltage over the second capillary. For negatively charged proteins, the procedure was the same except negative voltages were applied at the free ends of the capillaries. Mobility-based selective on-line preconcentration was also demonstrated with two negatively charged proteins, i.e. beta-lactoglobulin B and myoglobin. In this case, negative voltages of different values were applied at the free ends of the capillaries with different values, which provided a non-zero EOF in the system. The direction of EOF was the same as that of the electrophoretic migration velocities of the protein analytes in the first capillary and opposite in the second capillary. By controlling the EOF, beta-lactoglobulin B, which has a higher mobility, could be concentrated over 150-fold with a 15 min injection while myoglobin, which has a lower mobility, was eliminated from the system.     

Simultaneous Determination of Organic Acids in Wine Samples by Capillary Electrophoresis and UV Detection: Optimization with Five Different Background Electrolytes

A simple technique is described for the routine capillary electrophoretic determination of organic acids in wine samples. Several aromatic and non‐aromatic compounds, including phthalic acid, benzoic acid, sorbic acid, boric acid, and phosphate, were evaluated as background electrolytes in order to obtain the highest resolution and detection sensivity. Factors that affect capillary electrophoretic separation such as the concentration and pH of the background electrolyte (BGE), the concentration of the electroosmotic flow modifier (EOF), and methanol addition to the electrolyte were investigated systematically. Tartaric, malic, succinic, acetic, and lactic acids were determined simultaneously in approximately six minutes using an electrolyte containing 3 mM phosphate and 0.5 mM myristyltrimethylammonium bromide (MTAB) as electroosmotic flow modifier at pH 6.5. This method is quantitative, with recoveries in the 90–102% range and linear up to 50 mg L^–1. The precision is better than 1% and the procedure shows the appropriate sensibility, with detection limits between 0.015 and 0.054 mg L^–1. The proposed method was successfully employed for the determination of organic acids in wine samples by direct sample injection after appropriate dilution and filtration.     

Parameters influencing separation and detection of anions by capillary electrophoresis

Electrolyte composition is critical in optimizing separation and detection of ions by capillary electrophoresis. The parameters which must be considered when designing an electrolyte system for capillary electrophoresis include electrophoretic mobility of electrolyte constituents and analytes, detection mode, and compatibility of electrolyte constituents with one another. An electrolyte system based on pyromellitic acid is well suited for use with indirect photometric detection, and provides excellent separations of anions. The ability to modify the electrophoretic mobility of pyromellitic acid as a function of ph provides flexibility in matching electrophoretic mobilities of analytes. Additionally, the use of alkyl amines as electroosmotic flow modifiers allows the rapid separation of anions by reversing the direction of electroosmotic flow in a fused-silica capillary. The optimization of a capillary electrophoresis electrolyte for anion analysis is also discussed in terms of pH, ionic strength and applied voltage. The effect of organic solvent on separation selectivity is also discussed.     

On-line concentration and separation of indolamines, catecholamines, and metanephrines in capillary electrophoresis using high concentration of poly(diallyldimethylammonium chloride)

This paper tackles a simple and efficient method for the simultaneous separation and stacking of neurotransmitters in capillary electrophoresis with UV detection. By using poly(diallyldimethylammonium chloride) (PDDAC) as a buffer additive, the high and reversed EOF are observed. Moreover, the mobility of indolamines and catecholamines decreases as the PDDAC concentration increases. Based on the difference in mobility in the presence and absence of PDDAC, the analytes were simply stacked between the boundary of the sample zone and the background electrolyte containing PDDAC. The separation of 14 analytes including indolamines, catecholamines, and metanephrines was accomplished within 33 min under optimal conditions (1.2% PDDAC and 5 mM formic acid at pH 4.0), and the values of relative standard deviation of their migration time were less than 3.1%. By applying stacking methods for fourteen analytes, we observed: (a) the sample injection volume of sample is up to 216 nL, (b) the limits of detection at signal-to-noise of 3 range from 15.4 to 122.1 nM, and (c) the sensitivity enhancements, compared to normal injection (12 nL), range from 110- to 220-fold. Under the optimal stacking conditions, the present method has been applied to analyze of vanillomandelic acid, 5-hydroxyindole-3-acetic acid, dopamine, tryptamine, and 3-indoxyl sulfate in urine samples.     

Method development and validation for the simultaneous determination of four coumarins in Saussurea superba by capillary zone electrophoresis

A capillary zone electrophoretic method has been developed for the determination of four coumarins--skimmin, scopolin, scopoletin, and umbelliferone-in Saussurea superba with UV detection at 254 nm. The capillary temperature was kept constant at 25 degrees C. Effects of buffer pH, electrolyte concentration, organic modifier, and applied voltage on migration behavior were studied systematically. The optimum conditions for separation were achieved by using 30 mM borate buffer at pH 9.02 containing 15% (v/v) methanol as the electrolyte and 25 kV as the applied voltage. For all analytes a good linear regression relationship (r > 0.999) was obtained between peak area and concentration over a relatively wide range. The method was validated for repeatability, precision, and accuracy. The validated method was successfully applied to the simultaneous determination of the four analytes in S. superba.     

Characteristics of the electroosmotic flow of electrolyte systems for nonaqueous capillary electrophoresis

Nonaqueous capillary electrophoresis (NACE) is a powerful tool for the analysis of surface-active substances, which represent a broad class of analytes containing cationic and anionic species, such as surfactants, phosphoric acid esters, and amines. In order to conduct an efficient method development in NACE, the influence of the electrolyte composition on the electroosmotic flow (EOF) of organic separation systems was systematically investigated. Background electrolytes and background chromophores appropriate for direct and indirect UV-detection were considered, as the majority of surface-active substances do not absorb UV-light. It was found that theoretical models developed to describe the EOF in aqueous electrolyte systems are insufficient for organic electrolyte systems. Experimental data on electroosmosis in a variety of organic solvents and mixtures of methanol and acetonitrile applying different background chromophores and basic or acidic additives are given. Differences between them are discussed with relation to the physicochemical properties of the organic solvents.     

Transient isotachophoresis of highly saline trace metals under strong electroosmotic flow conditions

Transient isotachophoresis (TITP) is usually performed under low-electroosmotic flow (EOF) conditions using a coated capillary or a low pH background electrolyte. We used a bare fused-silica capillary for TITP stacking of anionic complexes of some heavy metals under high-EOF conditions (pH 9.0). The sample component chloride as a leading electrolyte induced stacking by an isotachophoretic mechanism and the complexing agent 4-(2-pyridylazo) resorcinol (PAR) acted as a terminating electrolyte. The optimized background electrolyte was composed of 150 mM N-tris(hydroxymethyl)methyl-3-aminopropanesulfonic acid, 127 mM triethylamine, and 0.1 mM PAR at pH 9.0. The strong EOF at pH 9.0 pulled the analytes against their mobilities toward the outlet side, allowing a separation in the normal polarity mode. The stacking efficiency, reproducibility, analysis time, and sample loading capacity in coated and bare capillaries were compared. The stacking efficiency and reproducibility were higher and the analysis time was shorter in the coated capillary. However, a larger volume of a sample could be injected in the bare capillary to achieve detection limits comparable to those for the coated one without compromising the resolution between the analyte peaks. The limits of detection (S/N = 3) were in the sub-ppb range for the selected metals (Fe2+, 0.3 ppb; Ni2+, 0.16 ppb; and Zn2+, 0.8 ppb) in a standard saline sample with 250 mM NaCl matrix. The proposed method was successfully applied to the analysis of reference urine samples and human urine samples.     

Constant pressure-assisted electrokinetic injection for on-line enhanced detection of monophthalates in capillary electrophoresis-mass spectrometry with application to human urine

Electrophoresis characteristics of several monophthalates in the sample zone and EOF variation in a fused-silica capillary column during a constant pressure-assisted electrokinetic injection (PAEKI) in an on-line CE-MS were studied in an effort to reconcile the mobility theory and field amplification with the enhancement achieved in present work. Influences of capillary length on the amount injected using PAEKI were investigated in detail and except for the injection time, the amount injected was found to increase linearly with capillary column length. A longer capillary provides a longer linear increase time range with PAEKI injection. The results show that smaller m/z analytes generate a large enhancement power using PAEKI, which is in agreement with the mobility theory. ACN was used as an example to investigate influences of organic additives on the amount injected and was found to decrease the amount injected with PAEKI injection, which is in agreement with an increase of resistivity in running buffer by organic additives. The peak width obtained with PAEKI injection proved to be independent of the amount injected. The band size of the sample zone was estimated by comparison with conventional hydrodynamic injection. A 240 s PAEKI injection achieved the same size of sample zone as a 2 s of hydrodynamic injection. Existance of two ion layers around the boundary of the buffer and sample solutions in sample zone was hypothesized to contribute the narrow sample zone with a long time of PAEKI injection. With a 240 s on-line PAEKI injection in CZE-MS, five monophthalates were enriched several hundred times without compromise in their separation efficiency and peak shape. With appropriate sample cleanup, PAEKI was applied to the analysis of monophthalates in urine samples, achieving detection limits ranging between 0.53 and 1.3 ng/mL.     

Impact of organic solvents on the resolution of synthetic peptides by capillary electrophoresis

The effect of variations in the concentrations of different organic solvents, including acetonitrile, methanol, ethanol, propanol and isopropanol, with aqueous buffer electrolytes of defined composition and pH on the electroosmotic flow velocity, v(EOF), of uncoated fused silica capillaries and on the electrophoretic mobility, mu(e), of synthetic peptides in high-performance capillary electrophoresis (HPCE) has been systematically investigated. In these experiments, the volume fractions of the organic solvent in the aqueous buffer electrolyte were changed from psi = 0.0 to 0.80. The addition of these organic solvents to the aqueous buffer electrolyte reduced the electroosmotic flow (EOF) of the system, but to significantly different extents. For the protic solvents as the alkyl chain of the alcohol increased, at the same volume fraction the greater was the influence on the electroosmotic flow. However, for the aprotic solvent, acetonitrile, the EOF did not change substantially as the volume fraction was varied. The electrophoretic mobility of synthetic peptides under the different buffer electrolyte conditions showed similar trends, confirming that the content and type of the organic modifier can be rationally employed to subtly manipulate the separation selectivity of synthetic peptides. These results, therefore, provide fundamental insight into the experimental options that can be used to maximise resolution of synthetic peptides in HPCE with aqueous buffer-organic solvent mixtures as well as a basis to select optimal binary or ternary buffer electrolyte compositions for the analysis of peptides when hyphenated techniques, such as HPCE-electrospray ionisation mass spectrometry (ESI-MS), are contemplated for the analysis of peptide samples of low abundance as can often be experienced in proteomic investigations.     

Analysis of drying oils used as binding media for objects of art by capillary electrophoresis with indirect UV and conductivity detection

Capillary electrophoresis (CE) was applied to analyse the long-chain fatty acid composition of vegetable oils, and their degradation products formed upon ageing when drying oils are used as binding media. The analytes were detected with contactless conductivity detection (CCD) and indirect UV absorption, both detectors positioned on-line at the separation capillary. The long-chain fatty acids were resolved in a background electrolyte (BGE) consisting of phosphate buffer (pH = 6.86, 15 mM) containing 4 mM sodium dodecylbenzensulfonate, 10 mM Brij 35, 2% (v/v) 1-octanol and 45% (v/v) acetonitrile. As in this system dicarboxylic analytes, the products of oxidative degradation of unsaturated fatty acids, cannot be determined, a suitable background electrolyte was developed by the aid of computer simulation program PeakMaster. It makes use of a 10 mM salicylic acid, 20 mM histidine buffer, pH 5.85, which combines buffering ability with the optical properties obligatory for indirect UV detection. This buffer avoids system eigenpeaks, which are often impairing the separation efficiency of the system. Separation of the dicarboxylic analytes was further improved by a counter-directed electroosmotic flow (EOF), obtained by dynamically coating the capillary wall with 0.2 mM cetyltrimethylammonium bromide. Long-chain fatty acids and their decomposition products could be determined in recent and aged samples of drying oils, respectively, and in samples taken from two paintings of the 19th century.     

Quantitative analysis of microcystin variants by capillary electrophoresis mass spectrometry with dynamic pH barrage junction focusing

Dynamic pH junction is an online focusing method in CE based on the electrophoretic mobility difference of analytes in the sample matrix and the background electrolyte. An advantage of this method over the conventional CE is that the sensitivity can be significantly improved. By injecting a long sample plug in the capillary and focusing the analytes at the pH boundary between the background electrolyte and sample matrix, the LOD can be improved by 10–100 folds. The dynamic pH junction method can be easily coupled with ESI‐MS. In this work, we used this method for the analysis of microcystins (MCs). The detection limits and dynamic ranges were studied. The separation was optimized by adjusting the injection time, and concentrations and pH values of the background electrolyte. The optimization of analyte focusing leads to enhanced detection response compared to conventional injections, achieving 200–400 fold higher averaged peak heights for four microcystin (MC) variants. More importantly, this method was successfully used for the quantitative analysis of microcystins (MCs) in crude algae samples from natural water bodies, making it promising for practical applications.     

Separation of organic and inorganic arsenic species by capillary electrophoresis using direct spectrophotometric detection

Capillary electrophoresis (CE) with UV detection was used for the determination of arsenite, arsenate, monomethylarsonic acid, dimethylarsinic acid, p-aminophenylarsonic acid, 4-hydroxy-3-nitrobenzenearsonic acid, 4-nitrophenylarsonic acid, phenylarsonic acid, and phenylarsine oxide. The electrophoretic mobilities of these anionic species were determined in a 20 mM phosphate buffer in a pH range from 4 to 11, which established pH 10 as the optimum for the separation. The target analytes were then separated in a fused-silica capillary using 20 mM NaHCO(3)-Na(2)CO(3) buffer, pH 10, as electrolyte and detected at 192 nm. Both normal- and reversed electroosmotic flow (EOF) separation modes were investigated and in the latter case, poly(diallydimethylammonium chloride) (PDDAC), was used for dynamic coating of the capillary and to provide a stable and reproducible reversed EOF (relative standard deviation RSD, 0.39%). The influence of electrolyte pH and composition, applied voltage, as well as EOF reversal protocols upon the method performance criteria were investigated. The optimised method provided limits of detection for the target analytes of 1.62, 6.22, 1.45, 1.83, 0.34, 0.40, 0.40, 0.18, and 0.30 mg/L As, respectively. Linearity was obtained in the range of 0.5-40 mg/L As (for aryl compounds) and from 5-100 mg/L As (for the remaining analytes). Reproducibility of peak areas was in the range of 0.8-5.5% RSD. The method was applied to the determination of four aryl arsenic compounds used as additives in animal feed. Analytes were extracted with 40 mM hydrochloric acid - acetonitrile 4:1 v/v, and then cleaned up by passing through a C(18) solid-phase extraction cartridge before analysis by CE with detection at 200 nm. Recoveries for the four analytes were in the range of 78.8-108.3%.     

Co-electroosmotic capillary electrophoresis determination of phenolic acids in commercial olive oil

Fourteen phenolic acids have been selectively determined in olive-oil samples using the co-electrosmotic capillary electrophoresis mode with UV detection after the LLE extraction system. A polycationic surfactant (hexadimetrine bromide, HDB), which dynamically coats the inner surface of the capillary and causes a fast anodic electroosmotic flow, was added to the electrolyte. The main factors affecting co-electroosmotic flow (EOF) such as type of modifier, concentration, and influence of organic solvents have been studied. Other parameters such as pH, type, and concentration of buffer, applied voltage, and injection time were also optimised using hydrodynamic injection for 8 s and UV detection at 210 nm. The composition optimum of the running buffer used was a 20% 2-propanol, 0.001% HDB, and 50 mM sodium borate at a pH value of 9.6. The method has been applied to determination and quantification of fourteen phenolic acids at ppb levels in olive oil samples after a liquid-liquid extraction.