Preparation and dielectric properties of polyimide foams containing crosslinked structures

In order to obtain cellular materials with low dielectric properties, crosslinked polyimide foams were prepared using 3,3′,4,4′‐benzophenonetetracarboxylic dianhydride (BTDA), 4,4′‐oxydianiline (ODA) and 2,4,6‐triaminopyrimidine (TAP) as monomer via a poly(ester‐amine salt) precursor process. The structures of the precursors and the polyimide foams were characterized by thermogravimetric analysis (TGA) and FT‐IR, while the morphologies of the polyimide foams were viewed from scanning electron microscopy (SEM) measurements. The results revealed that the poly(ester‐amine salt) precursor containing TAP could successfully be converted to a crosslinked polyimide foam with relatively uniform cell structure. Also, the crosslinking of TAP improved the mechanical properties of foams in comparison with the non‐crosslinking systems. With increasing content of TAP, the dielectric constants of the polyimide foams decreased gradually. For the foam with TAP molar ratio at 15%, the dielectric constant was as low as 1.77 at the frequency of 10 kHz. Though the thermal resistance decreased slightly for crosslinked foams, the decomposition temperatures were still maintained above 520°C. Copyright © 2006 John Wiley & Sons, Ltd.     

Low‐Temperature Sol‐Gel Synthesis of Nanostructured Polymer/Titania Hybrid Films based on Custom‐Made Poly(3‐Alkoxy Thiophene)

A low‐temperature route to directly obtain polymer/titania hybrid films is presented. For this, a custom‐made poly(3‐alkoxy thiophene) was synthesized and used in a sol‐gel process together with an ethylene‐glycol‐modified titanate (EGMT) as a suitable titania precursor. The poly(3‐alkoxy thiophene) was designed to act as the structure‐directing agent for titanium dioxide through selective incorporation of the titania precursor. The nanostructured titania network, embedded in the polymer matrix, is examined with atomic force microscopy (AFM) and scanning electron microscopy (SEM) measurements. By means of the scattering technique grazing incidence wide‐angle X‐ray scattering (GIWAXS), a high degree of crystallinity of the polymer as well as successful transformation of the precursor into the rutile phase of titania is verified. UV/Vis measurements reveal an absorption behavior around 500 nm which is similar to poly(3‐hexyl thiophene), a commonly used polymer for photoelectronic applications, and in addition, the typical UV absorption behavior of rutile titania is observed.     

Efficient Hydrogen Evolution Electrocatalysis Using Cobalt Nanotubes Decorated with Titanium Dioxide Nanodots

TiO₂ Co nanotubes decorated with nanodots (TiO₂ NDs/Co NSNTs‐CFs) are reported as high‐performance earth‐abundant electrocatalysts for the hydrogen evolution reaction (HER) in alkaline solution. TiO₂ NDs/Co NSNTs can promote water adsorption and optimize the free energy of hydrogen adsorption. More importantly, the absorbed water can be easily activated in the presence of the TiO₂–Co hybrid structure. These advantages will significantly promote HER. TiO₂ NDs/Co NSNTs‐CFs as electrocatalysts show a high catalytic performance towards HER in alkaline solution. This study will open up a new avenue for designing and fabricating low‐cost high‐performance HER catalysts.     

Synthesis,structure, and properties of polyimide and polyurethane‐urea‐imide copolymers

Several, novel polyimide–polyurethane‐urea‐imide (PI‐PUI) copolymers with different polyimide (PI) contents were prepared by an in situ interpenetrating reaction between polyurethane‐urea‐imide (PUI) precursor and poly(amide acid). Changing the ratio of the PUI precursor and poly(amide acid) resulted in a change of the properties of the PI‐PUI copolymers from plastic to elastomer. Fourier transform infrared spectra revealed the characteristic absorption bands of PI‐PUI copolymers; differential scanning calorimetry (DSC) analyses revealed that the glass‐transition temperature of the soft‐segment‐rich phase decreased as the PI content increased in PI‐PUIs, meaning that the soft segments (i.e., PEG) were more incompatible and had better crystallizability with a high‐PI‐segment content in PI‐PUI. Wide‐angle X‐ray diffraction curves exhibited more ordered structure within the disordered PI‐PUI copolymer's state with an increasing PI content, which further agreed with the DSC results. Scanning electron micrographs clearly showed that the molecular chains in PI‐PUI with a high‐PI‐content packed, ordered lamellar structure. Thermogravimetric curves indicated that the heat resistance of PI‐PUI was better than pure PUI. The introduction of the PI component into PUI by an in situ interpenetrating reaction method is an effective way to improve the thermal stability and solvent resistance of PUI. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 216–225, 2004     

Probing the tribological behaviors in water of novel poly(phthalazione ether sulfone ketone) and its composites based on the state of aggregation and the microstructure

In this paper, novel poly(phthalazione ether sulfone ketone) (PPESK) and its composites reinforced with carbon fibers (CFs) were prepared, and their tribological behaviors in pure and sea water were comparatively investigated. Affected by the noncoplanar twisted aromatic structure in the molecular skeleton, the aggregation of the macromolecular chain in PPESK was amorphous, resulting in very high water absorption of PPESK matrix. The invading water molecules led to a sharp decrease in the hardness of PPESK surface, resulting in very high wear rate of PPESK in water. Although CF/PPESK composites had higher water absorption than pure PPESK, their wear processes in water were no longer dominated by high water absorption but by the load‐carrying effect of CFs, ascribed to the good CF/PPESK interfacial adhesion. Therefore, CF/PPESK composites exhibited very low wear rates in the order of 10^?7 mm³/Nm in water, which decreased with the CF content increasing until the content of CFs reached 50%. The results revealed that the most critical factor determining the wear behavior of a fiber‐reinforced polymer composite sliding in water is the fiber/matrix interface but not the water absorption of the polymer matrix. Copyright © 2017 John Wiley & Sons, Ltd.     

Synthesis and properties of new aromatic poly‐(ether benzoxazole)s from 2,2′‐bis(4‐amino‐3‐hydroxyphenoxy)biphenyl and aromatic dicarboxylic acid chlorides

A new bis(o‐aminophenol) with a crank and twisted noncoplanar structure and ether linkages, 2,2′‐bis(4‐amino‐3‐hydroxyphenoxy)biphenyl, was synthesized by the reaction of 2‐benzyloxy‐4‐fluoronitrobenzene with biphenyl‐2,2′‐diol, followed by reduction. Biphenyl‐2,2′‐diyl‐containing aromatic poly(ether benzoxazole)s with inherent viscosities of 0.52–1.01 dL/g were obtained by a conventional two‐step procedure involving the polycondensation of the bis(o‐aminophenol) monomer with various aromatic dicarboxylic acid chlorides, yielding precursor poly(ether o‐hydroxyamide)s, and subsequent thermal cyclodehydration. These new aromatic poly(ether benzoxazole)s were soluble in methanesulfonic acid, and some of them dissolved in m‐cresol. The aromatic poly(ether benzoxazole)s had glass‐transition temperatures of 190–251 °C and were stable up to 380 °C in nitrogen, with 10% weight losses being recorded above 520 °C. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 2656–2662, 2002     

Study on structure and performance of surface‐metallized carbon fibers reinforced rigid polyurethane composites

The simultaneous promotion in mechanical and electrical properties of rigid polyurethane (RPU) is an important task for expanding potential application. In this work, carbon fibers (CFs) reinforced RPU composites were prepared with the goal of improving mechanical and electrical properties. Metallized CFs meet our performance requirements and can be easily achieved via electrodeposition. However, the weak bonding strength in fiber‐metal‐RPU interface restricts their application. Inspired by the reducibility and wonderful adhesion of dopamine (DA), we proposed a new and efficient electrochemical method to fabricate metallized CFs, where DA polymerization was simultaneously integrated coupled with the reduction of metal ions (Ni²⁺). The characterization results helped us to gain insight about the reaction mechanism, which was never reported as far as we know. Compared with pure RPU, the tensile, interlaminar shear and impact strength of polydopamine (PDA)‐nickel (Ni) modified CFs/RPU composites were improved by 11.2%, 21.0%, and 78.0%, respectively, which attributed to the strong interfacial adhesion, including mechanical interlocking and chemical crosslinking between treated CFs and RPU. In addition, the PDA‐Ni surface treatment method also affected the dispersion of short CFs in the RPU, which increased the possibility of conductor contact and reduced insulator between fibers networks, resulting in higher electrical conductivity.     

A New Kind of Copolymerization of Styrene and p‐Quinodimethane Intermediates

A new kind of copolymerization between styrene and p‐quinodimethane intermediates was realized by adding styrene to a reaction performed via the typical chlorine precursor route toward the synthesis of poly(p‐phenylene vinylene) (PPV). The composition and structure of the obtained copolymers can be adjusted by the feed rate of the two monomers. The resulting copolymers show improved solubility and blue‐shifted photoluminescence as compared with the corresponding PPV derivative.     

Influence from Thermal Elimination Temperature of Precursor Polymer and Film‐forming Methods on the Photophysics of the Poly(2,5‐didodecyloxy‐p‐phenylenevinylene)

A series of poly(p‐phenylenevinylene)s (PPVs) with good solubility were synthesized from thermal elimination of precursor poly(2,5‐didodecyloxy‐p‐phenylenevinylene) at different temperature via Wessling method. The polymer photophysics were influenced by the thermal elimination condition, which was consistent with NMR and IR characterizations. The additional absorption peak at longer wavelength and the red‐shifted emission maximum both in solution and in film, for PPVs obtained at high elimination temperature, indicated the existence of longer conjugated blocks in these systems. The emission maximum for drop‐cast film (436 nm) for PPV obtained under 200°C (PPV200) was 16 nm blue shifted to the spin‐coated films (452 nm) or 29 nm to the solution (465 nm). The SEM study showed drop‐cast film had the morphology of isolated conjugated particles in the matrix while blurry linear structure was found for spin‐coated film, which was consistent with the photophysics. The discussion about this difference was carried out based on the consideration of the flexibility of the polymer chains and different conjugated length of PPV in different states.     

Preparation and characterization of a polyimide nanofoam through grafting of labile poly(propylene glycol) oligomer

Preparation of a polyimide nanofoam (PI‐F) for microelectronic applications was carried out using a polyimide precursor synthesized from poly[(amic acid)‐co‐(amic ester)] and grafted with a labile poly(propylene glycol) (PPG) oligomer. Polyimide precursor was synthesized by partial esterification of poly(amic acid) (PAA) derived from pyromellitic dianhydride (PMDA) and 4,4′‐oxydianiline (ODA). The precursor was then grafted with bromide‐terminated poly(propylene glycol) in the presence of K₂CO₃ in hexamethylphosphoramide and N‐methylpyrrolidone, imidized at 200°C in nitrogen and the product was subsequently decomposed in air at 300°C to eliminate the labile PPG oligomer to produce PMDA/ODA polyimide nanofoam. Nuclear magnetic resonance spectroscopy (¹H‐NMR) and Fourier transform infrared spectroscopy (FT‐IR) techniques were used to characterize the formation of polyimide precursor and extent of grafting of PPG with polyimide. The results of thermogravimetric analysis (TGA) showed three step decomposition of nanofoam with the removal of PPG at 350°C and decomposition of polyimide at around 600°C. The polyimide nanofoams were also characterized by small angle X‐ray scattering (SAXS), field‐emission scanning electron microscopy (FE‐SEM) and transmission electron microscopy (TEM). The morphology showed nanophase‐separated structures with uniformly distributed and non‐interconnected pores of 20–40 nm in size. Dynamic mechanical analysis (DMA) indicated higher storage modulus for the foamed structure compared to the pure PI with reduction in loss tangent for the former system. Copyright © 2004 John Wiley & Sons, Ltd.     

A Tailor‐Made Synthetic Polymer for Cell Encapsulation: Design Rationale,Synthesis, Chemical–Physics and Biological Characterizations

This study presents a custom‐made in situ gelling polymeric precursor for cell encapsulation. Composed of poly((2‐hydroxyethyl)methacrylate‐co‐(3‐aminopropyl)methacrylamide) (P(HEMA‐co‐APM) mother backbone and RGD‐mimicking poly(amidoamine) (PAA) moiteis, the comb‐like structured polymeric precursor is tailored to gather the advantages of the two families of synthetic polymers, i.e., the good mechanical integrity of PHEMA‐based polymers and the biocompatibility and biodegradability of PAAs. The role of P(HEMA‐co‐APM) in the regulation of the chemico‐physical properties of P(HEMA‐co‐APM)/PAA hydrogels is thoroughly investigated. On the basis of obtained results, namely the capability of maintaining vital NIH3T3 cell line in vitro for 2 d in a 3D cell culture, the in vivo biocompatibility in murine model for 16 d, and the ability of finely tuning mechanical properties and degradation kinetics, it can be assessed that P(HEMA‐co‐APM)/PAAs offer a cost‐effective valid alternative to the so far studied natural polymer‐based systems for cell encapsulation.

     

Synthesis of poly(oxyethylene phosphoramidate)s and glycopolymers via Staudinger reaction: Multivalent binding studies with Concanavalin A

A new method for the preparation of poly(oxyethylene phosphoramidate)s and glycopolymers is developed via modification of poly(oxyethylene H‐phosphonate) which is a biodegradable, biocompatible and low toxic polymer. The phosphonate groups of the precursor are converted into tri‐coordinated phosphorus species yielding poly(oxyethylene trimethylsilyl phosphite). The latter is then reacted with different azides, including sugar azides, via Staudinger reaction to furnish the desired poly(oxyethylene phosphoramidate)s and such containing sugar moieties in the side chains attached to the P‐centers. 2002P NMR spectroscopy is applied as a powerful tool for determination of the conversion and structure of the reaction products. Studies on Concanavalin A binding to the obtained glycopolymers are performed using dynamic light scattering and analytical ultracentrifugation techniques. The viability of Human Embryonic Kidney 293 cell line is slightly affected when exposed to polyphosphoramidate glucoconjugate over a broad range of concentrations. The results obtained are encouraging for further investigations on the clustering and bio‐recognition properties of the synthesized glycopolymers. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 1730–1741     

Precision synthesis of microstructures in star‐shaped copolymers of ϵ‐caprolactone,L‐lactide,and 1,5‐dioxepan‐2‐one

Star‐shaped homo‐ and copolymers were synthesized in a controlled fashion using two different initiating systems. Homopolymers of ε‐caprolactone, L ‐lactide, and 1,5‐dioxepan‐2‐one were firstly polymerized using (I) a spirocyclic tin initiator and (II) stannous octoate (cocatalyst) together with pentaerythritol ethoxylate 15/4 EO/OH (coinitiator), to give polymers with identical core moieties. Our gained understanding of the versatile and controllable initiator systems kinetics, the transesterification reactions occurring, and the role which the reaction conditions play on the material outcome, made it possible to tailor the copolymer microstructure. Two strategies were used to successfully synthesize copolymers of different microstructures with the two initiator systems, i.e., a more multiblock‐ or a block‐structure. The correct choice of the monomer addition order enabled two distinct blocks to be created for the copolymers of poly(DXO‐co‐LLA) and poly(CL‐co‐LLA). In the case of poly(CL‐co‐DXO), multiblock copolymers were created using both systems whereas longer blocks were created with the spirocyclic tin initiator. © 2008 Wiley Periodicals, Inc. JPolym Sci Part A: Polym Chem 46: 1249–1264, 2008     

Diameter dependence of hybrid shish‐kebab structure in polyethylene/carbon material fiber composites

PE chains can proceed template crystal growth on multi‐walled carbon nanotubes (MWCNTs) surface and develop into hybrid shish‐kebab (HSK) abiding by the “soft epitaxy” mechanism. For large‐diameter carbon nanofiber (CNF), the lattice matching and epitaxy are the main mechanism for hybrid structure formation under the static state. This study provided a new understanding of HSK formation, wherein PE underlay on the surface of carbon material fiber played an important role. The shear flow induced PE chains to orient along the CNF surface and formed PE underlayer. Subsequently, ordered subglobules were periodically formed along the CNF axis and finally evolved to typical HSK structures with well‐aligned arraying PE lamellae rather than random one. As the diameter increased to 7000 nm, even though the graphite (002) planes in carbon fibers (CFs) was similar to that in CNFs, the attractive van der Waals interactions between CFs and PE chains were too weak to drive enough PE chains to absorb on the CFs surface and form PE underlay even under the shear flow, leading to the absence of PE lamellae on the CF surface. Based on that, the “soft epitaxy” could be the main formation mechanism of HSK structures for carbon material fibers regardless of their diameters. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 297–303     

Supramolecular Structures,Organization and Surface Behavior at Interfaces

The surface behavior of Supramolecular Structures as inclusion complexes^[1] were studied. The inclusion complexes (ICs) obtained from the threading of α-cyclodextrin (α-CD) with poly(ε-caprolactone) (PEC) and derivatives as precursor homopolymers were prepared and characterized by ¹H-NMR and FT-IR Microscopy. In order to investigate the influence of the chemical structure of the other precursor homopolymers as poly(ethylene oxide) (PEO) and poly(tetrahydrofuran) (PTHF), the inclusion complexes (ICs) were also obtained from the threading of α-cyclodextrin (α-CD) with these polymers. Surface pressure-area isotherm (π-A) at the air-water interface were determined by the Langmuir Technique for all the ICs and their polymers. Due to solubility reasons, different spreading solvents were used. In a set of control experiments, it was observed that the spreading volume did not influence significantly the isotherms for any polymeric systems studied. It was found that the hydrophobic and hydrophilic balance changes with the increasing of the methylene and hydroxyls groups number in the chemical structures of the precursor polymers involved in the ICs. The degree of hydrophobicity of the different supramolecular systems was also estimated from the determination of the surface free energy (SE) values using the wettability measurements.^[2] In order to describe the experimental behavior of the ICs and the precursor polymers, molecular dynamics simulation (MDS) were performed. The radial distribution functions (RDF) between water molecules and hydrophilic and hydrophobic moieties of the polymeric systems studied were analized. By this way it was possible to visualize the orientation and the organization of these supramolecular structures at the air-water interface.     

Synthesis,Solid‐State NMR Characterization,and Application for Hydrogenation Reactions of a Novel Wilkinson’s‐Type Immobilized Catalyst

Silica nanoparticles (SiNPs) were chosen as a solid support material for the immobilization of a new Wilkinson’s‐type catalyst. In a first step, polymer molecules (poly(triphenylphosphine)ethylene (PTPPE); 4‐diphenylphosphine styrene as monomer) were grafted onto the silica nanoparticles by surface‐initiated photoinferter‐mediated polymerization (SI‐PIMP). The catalyst was then created by binding rhodium (Rh) to the polymer side chains, with RhCl₃ ? x H₂O as a precursor. The triphenylphosphine units and rhodium as Rh^I provide an environment to form Wilkinson’s catalyst‐like structures. Employing multinuclear (³¹P, ²⁹Si, and ¹³C) solid‐state NMR spectroscopy (SSNMR), the structure of the catalyst bound to the polymer and the intermediates of the grafting reaction have been characterized. Finally, first applications of this catalyst in hydrogenation reactions employing para‐enriched hydrogen gas (PHIP experiments) and an assessment of its leaching properties are presented.     

Synthesis and characterization of polyphenylenes with polypeptide and poly(ethylene glycol) side chains

We report a novel approach for fabrication of multifunctional conjugated polymers, namely poly(p‐phenylene)s (PPPs) possessing polypeptide (poly‐l ‐lysine, PLL) and hydrophilic poly(ethylene glycol) (PEG) side chains. The approach is comprised of the combination of Suzuki coupling and in situ N‐carboxyanhydride (NCA) ring‐opening polymerization (ROP) processes. First, polypeptide macromonomer was prepared by ROP of the corresponding NCA precursor using (2,5‐dibromophenyl)methanamine as an initiator. Suzuki coupling reaction of the obtained polypeptide and PEG macromonomers both having dibromobenzene end functionality using 1,4‐benzenediboronic acid as the coupling partner in the presence of palladium catalyst gave the desired polymer. A different sequence of the same procedure was also employed to yield polymer with essentially identical structure. In the reverse sequence mode, low molar mass monomer (2,5‐dibromophenyl)methanamine, and PEG macromonomer were coupled with 1,4‐benzenediboronic acid in a similar way followed by ROP of the L‐Lysine NCA precursor through the primary amino groups of the resulting polyphenylene. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 1785–1793     

Three‐component negative‐type photosensitive polyimide precursor based on poly(amic acid), a crosslinker,and a photoacid generator

A new negative‐working and alkaline‐developable photosensitive polyimide precursor based on poly(amic acid) (PAA), 4,4′‐methylenebis[2,6‐bis(hydroxymethyl)]phenol (MBHP) as a crosslinker, and a photoacid generator (5‐propylsulfonyloxyimino‐5H‐thiophen‐2‐ylidene)‐2‐(methylphenyl)acetonitrile (PTMA) has been developed. PAA was prepared by ring‐opening polymerization of pyromellitic dianhydride with 4,4′‐oxydianiline. The photosensitive polyimide precursor containing PAA (65 wt %), MBHP (25 wt %), and PTMA (10 wt %) showed a clear negative image featuring 10 μm line and space patterns when it was exposed to 436 nm light at 100 mJ·cm^?2, post‐exposure baked at 130 °C for 3 min, followed by developing with a 2.38 wt % aqueous tetramethylammonium hydroxide solution at 25 °C. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 593–599, 2005     

Novel positive‐working and aqueous‐base‐developable photosensitive poly(imide benzoxazole) precursor

A novel positive‐working and aqueous‐base‐developable photosensitive poly(imide benzoxazole) precursor based on a poly(amic acid hydroxyamide) bearing phenolic hydroxyl groups and carboxylic acid groups, a diazonaphthoquinone (DNQ) photosensitive compound, and a solvent was developed. Poly(amic acid hydroxyamide) was prepared through the polymerization of 2,2‐bis(3‐amino‐4‐hydroxyphenyl)hexafluoropropane, trimellitic anhydride chloride, and 4,4′‐oxydibenzoyl chloride. Subsequently, the thermal cyclization of the poly(amic acid hydroxyamide) precursor at 350 °C produced the corresponding poly(imide benzoxazole). The inherent viscosity of the precursor polymer was 0.17 dL/g. The cyclized poly(imide benzoxazole) showed a high glass‐transition temperature of 372 °C and 5% weight loss temperatures of 535 °C in nitrogen and 509 °C in air. The structures of the precursor polymer and the fully cyclized polymer were characterized with Fourier transform infrared and ¹H NMR. The photosensitive polyimide precursor containing 25 wt % DNQ photoactive compound showed a sensitivity of 256 mJ/cm² and a contrast of 1.14 in a 3‐μm film with a 0.6 wt % tetramethylammonium hydroxide developer. A pattern with a resolution of 5 μm was obtained from this composition. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5990–5998, 2004     

Poly(ether ether ketone)‐bischromenes: Synthesis,characterization, and influence on thermal,mechanical, and thermo mechanical properties of epoxy resin

Poly(ether ether ketone) s with terminal propargyl groups (PEEK‐PR) were synthesized from hydroxyl terminated PEEK (PEEKTOH) and characterized. The heat‐triggered polymerization of PEEK‐PR to poly bischromenes having PEEK backbone was confirmed by Fourier transform infrared spectroscopy and differential scanning calorimetric studies. PEEK‐PR was blended with a bisphenol based epoxy resin‐diamino diphenylsulphone system in different proportions and cured to form PEEK‐bischromene‐interpenetrated‐epoxy‐amine networks. Tensile strength and elongation of the cured blends increased up to 10‐phr loading of PEEK‐PR and then declined. Tensile moduli of all formulations were comparable. Fracture toughness increased by a maximum of 33%, and the fractured surface morphology showed a ductile fracture. The blends exhibited slightly lower glass transition temperature to that of the neat epoxy‐amine system. A reference sample of epoxy‐amine was processed with the optimum loading of the precursor polymer, PEEKTOH, and compared its properties with the PEEK‐PR incorporated epoxy systems. In this way, it is found that the incorporation of addition curable propargylated PEEK increases the strength characteristics with adequate thermal stability and fracture toughness for high‐performance structural applications.