Monitoring road surfaces by close proximity noise of the tire/road interaction

Applied acoustics is becoming an important field for civil infrastructure and environmental assessment, and road maintenance or rehabilitation strategies. In this research LA(2)IC has developed a GPS-based measurement techniques and apparatus on a test vehicle, for monitoring the acoustical properties of different road pavement surfaces with a reference tire. A field test on PA-12 Spanish porous pavement found in Ciudad Real is developed. The test procedure, a modification based upon the close-proximity method (CPX), relies on the use of three standard microphones situated very close to the tire/road contact patch. This procedure allows the simultaneous measurement of the sound emission synchronized to a GPS receiver, which permits tracking of the position of the sound emission. Geo-referenced sound spectra for every 10 m during individual passes of the test vehicle are analyzed to determine the tire/road noise emissions from tire/PA-12 pavement interaction. Noise levels of around 102 dB(A), with a variability of approximately 0.6 dB(A), are found at a reference vehicle speed of 85 kmh. The frequency spectrum analysis over the test section shows noticeable differences for frequencies above 1 kHz, where the tire/road noise generation mechanisms are dominated by air pumping.     

Quantitative measurement of pass-by noise radiated by vehicles running at high speeds

It has been a challenge in the past to accurately locate and quantify the pass-by noise source radiated by the running vehicles. A system composed of a microphone array is developed in our current work to do this work. An acoustic-holography method for moving sound sources is designed to handle the Doppler effect effectively in the time domain. The effective sound pressure distribution is reconstructed on the surface of a running vehicle. The method has achieved a high calculation efficiency and is able to quantitatively measure the sound pressure at the sound source and identify the location of the main sound source. The method is also validated by the simulation experiments and the measurement tests with known moving speakers. Finally, the engine noise, tire noise, exhaust noise and wind noise of the vehicle running at different speeds are successfully identified by this method.     

Airborne sound emission as a process monitoring tool in the cut-off grinding of concrete

A detailed analysis of the airborne sound emitted in the cut-off grinding of concrete with a diamond grinding disk is presented. It is shown that the frequency spectra of airborne sound emitted in the cutting process contain detailed information about the process conditions. As long as the machining parameters are appropriate for the work piece, the airborne sound spectra show statistically excited natural frequencies and turning frequencies. In this case the total signal level gives sufficient evidence of the work piece composition and machinability. The effects of inappropriate machining parameters, like tool deflection or very high friction forces acting on the tool, can be identified by means of distinct frequencies in the airborne sound spectra. In addition, the emitted airborne sound can be used to image the structure of the flat joint surface, which cannot be determined by another method. With regard to everyday applications, the results obtained by this procedure can be used to apply airborne sound analysis systems to machines and detect process parameters which are overstressing the cutting tool.     

识别运动声源随机阵列生成法研究

针对随机阵列结构设计方面欠缺高效的生成方法这一问题,在保证阵列对声源识别精度的前提下,提出一种在极坐标下用于识别运动声源的随机阵列生成方法。根据声阵列识别运动声源的原理,推导了非等间距基本同轴圆环的半径,再通过降列分区、极坐标下条件筛选和模拟评价三个步骤,生成适用于识别运动声源的目标随机阵列,最后进行数值模拟和运动汽车噪声源识别实验进行验证。研究结果表明,用该方法能够高效地生成目标随机阵列,与常用规则阵列相比具有更良好的声源识别特性,并且具有准确的运动声源识别性能。      

高精度球面阵聚焦声源定位方法研究

提出了一种高精度高空间分辨率球面阵聚焦声源定位方法——虚拟源法。该方法通过球面阵波束扫描获得实际声源的空间聚焦谱,并假定各扫描点为虚拟声源,将实际声源聚焦谱看作是全体虚拟源共同作用的结果,由此得到各虚拟源对声场的贡献量,从而可实现声源精确定位。仿真研究分析了频率,阵列孔径,声场模态阶数,信噪比等参数对声源定位性能的影响,并与常规算法进行对比。结果显示,该方法不受频率和阵列孔径的限制,避免了空间“混淆”,能够进行高精度高分辨率声源定位,并具有良好的背景噪声抑制能力。      

浅海波导中简正波干涉特征频率增强

针对浅海波导中水平线列阵接收的低频宽带低信噪比信号,提出了一种利用多拍信号相干累加来提高干涉简正波特征频谱信噪比的方法。这种方法主要针对未知距离和声源形式的运动声源,对不同时刻(或接收距离)处阵列输出信号进行warping变换,根据干涉简正波的特征频率不变性,通过搜索距离与径向速度的比值来对齐未知距离下warping变换后的谱峰频率,进而通过相干累加来增强信号干涉简正波的特征频率。仿真和海上实验数据分析均验证了方法的性能。     

Wave field synthesis of moving virtual sound sources with complex radiation properties

An approach to the synthesis of moving virtual sound sources with complex radiation properties in wave field synthesis is presented. The approach exploits the fact that any stationary sound source of finite spatial extent radiates spherical waves at sufficient distance. The angular dependency of the radiation properties of the source under consideration is reflected by the amplitude and phase distribution on the spherical wave fronts. The sound field emitted by a uniformly moving monopole source is derived and the far-field radiation properties of the complex virtual source under consideration are incorporated in order to derive a closed-form expression for the loudspeaker driving signal. The results are illustrated via numerical simulations of the synthesis of the sound field of a sample moving complex virtual source.     

Ambisonics声捡拾与重放音色的双耳听觉模型分析与实验

提出用双耳听觉模型对空间声音色进行分析的普遍方法,并以Ambisonics为例进行了分析。Ambisonics是基于物理声场重构的空间声系统,其最终重构声场误差以及音色改变是由传声器捡拾和重放空间混叠误差共同引起的。采用修正的Moore双耳响度模型计算了Ambisonics重构声场的双耳响度级谱并和目标声场的情况比较,从而定量评价重构声场的音色改变。结果表明,在理想捡拾信号的情况下,无音色改变重放的上限频率和区域大小随Ambisonics的阶数而增加。而对于传声器阵列捡拾的情况,只要阵列的上限频率大于Ambisonics重放的上限频率,在重放的上限频率以下,传声器阵列空间混叠误差对最终重构声场及其感知音色的影响就可以忽略。在此基础上,提出了一种综合考虑捡拾与重放性能的Ambisonics系统优化设计方法。心理声学实验得到了和双耳听觉模型一致的结果,从而也验证了模型分析的有效性。      

Modulation of Mössbauer radiation by pulsed laser excitation

Experimental results on the observation of the modulation of Mössbauer radiation by pulsed laser radiation are presented. The time domain spectra agree well with the model of the frequency modulation of the Mössbauer radiation during the passage of the radiation through a vibrating resonance medium. The proposed methodology may be used for the study of opto-acoustic phenomena.     

Mössbauer spectrometer as a virtual instrument in the PXI/Compact PCI modular system

A new programming method has been used for building a computer-based Mössbauer spectrometer. Data acquisition is realized via two commercially available PXI/Compact-PCI modules or PCI devices which are supported by relevant software drivers. Both modules, the digital oscilloscope NI 5102 and the function generator NI 5401 (National Instruments Inc.), can be used in the PXI or PC standard. The synchronization between the velocity signal generation and the impulse detection is controlled by a RTSI (Real-Time System Integration) bus. A virtual Mössbauer spectrometer is implemented by the graphical programming language called LabVIEW 7 Express. The amplitude selection of impulses from the detector output is realized with an assistance of the Waveform Peak Detection.vi function. The sampling rate of the detector output signal and the frequency of the velocity signal determinate the number of registration channels of measured Mössbauer spectrum. The Mössbauer spectra can be accumulated in the constant or variable velocity modes; moreover, there is a possibility to register gamma-ray spectra in the multichannel analyzer mode.     

Radiation characteristics of multiple and single sound hole vihuelas and a classical guitar

Two recently built vihuelas, quasi-replicas of the Spanish Renaissance guitar, one with a small body and one sound hole and one with a large body with five sound holes, together with a classical guitar are investigated. Frequency dependent radiation strengths are measured using a 128 microphone array, back-propagating the frequency dependent sound field upon the body surface. All three instruments have a strong sound hole radiation within the low frequency range. Here the five tone holes vihuela has a much wider frequency region of strong sound hole radiation up to about 500 Hz, whereas the single hole instruments only have strong sound hole radiations up to about 300 Hz due to the enlarged radiation area of the sound holes. The strong broadband radiation of the five sound hole vihuela up to about 500 Hz is also caused by the sound hole phases, showing very consistent in-phase relations up to this frequency range. Also the radiation strength of the sound holes placed nearer to the center of the sound box are much stronger than those near the ribs, pointing to a strong position dependency of sound hole to radiation strength. The Helmholtz resonance frequency of the five sound hole vihuela is influenced by this difference in radiation strength but not by the rosettas, which only have a slight effect on the Helmholtz frequency.     

Mössbauer spectroscopy under acoustical excitation: thick target effects

A new model of Mössbauer absorption (transmission) spectra with an adequate analysis of the possible effects of acoustic excitation in the thick targets is proposed. In particular, the dependence of the line width of acoustical satellites on the degree of phase correlation of the sound oscillations of resonant nuclei in the target is established by calculations and confirmed in experiment. Such a model is stimulated by an increase in the informativeness of the Mössbauer experiments, using thick samples in ultrasound (US) field, and by possible applications of this research technique. The test measurements of Mössbauer absorption spectra on stainless steel are carried out. The fitting of these spectra confirms the relevance of modifications of the model base of Mössbauer processes in US field.     

单层传声器阵列信号空间重采样的声波分离方法

为了重构非自由声场中目标声源的声场响应,提出单层传声器阵列信号空间重采样的声波分离方法.以球面波函数为基函数,建立由系列球面波函数叠加表达的声场数学模型.基于近场声全息原理,利用单层传声器阵列面上空间重采样形成的两组声压测量信号,求解基函数系数,并重构出传声器阵列两侧声源各自的声场响应,实现声波分离.使用脉动球和振动球共同作用的非自由声场,检验了数学模型以及传声器信号信噪比、传声器阵列形状和面积、声源中心位置、频率等关键参数对声波分离精度的影响,并在全消声室内进行了实验验证.最后,对单层传声器阵列重采样的声波分离方法的实施给出了建议.     

Electromagnetic emission of mobile dislocation segments in an ionic crystal

The problem of electromagnetic emission of an edge dislocation segment moving in an ionic lattice with a NaCl-type structure is considered. The proposed mechanism of electromagnetic emission is associated with the appearance of macroscopic alternating polarization currents along the extraplane edge of the edge dislocation in the course of its motion between adjacent valleys of the Peierls relief. The relationships for electro-magnetic radiation fields of an arbitrarily moving segment are derived, and the problem of electromagnetic emission of a segment that executes harmonic oscillations in the field of an external quasi-stationary elastic wave with a frequency (where l is the segment length and c is the velocity of sound) is treated in detail. The power of the emitted electromagnetic signal and the “acoustoelectromagnetic transformation” coefficient (the ratio between the electromagnetic radiation power and the mechanical power required for setting the segment in motion) are determined.     

Transmission and radiation of acoustic oblique incident through tube arrays based on phononic crystals theory

In a utility boiler, the heat exchanger’s structure is similar to a two-dimensional phononic crystal. Based on the phononic crystal theory, this paper studies sound propagation through tube arrays as a function of the incident sound direction and the surroundings temperature. We carried out both the computational and experimental work for particular values of the pitch and diameters in the tube arrays and studied the band-gap diagram and insertion loss spectra for different angles of incidence. The first band gap is found to correspond to Bragg’s Law while the second band gap moves to lower frequencies as the angle increases. Simulations indicate also that the uneven temperature field influences the insertion loss spectrum. Results of experiments and calculations confirm that, for a particular tube array, the most important factors influencing sound propagation are incidence angle and the surrounding temperature. For the acoustic source in tube arrays, the acoustic radiation have relation with the frequency whether in the acoustic bang gap or not. The results should provide a basis for further work: both on sound source localization and low frequency sonic cleaning in large tube arrays.     

频率自适应最优权重阵列干涉条纹处理技术

考虑长基线水平阵列波束形成对声场模态呈现的滤波特征,建立了一种随频率改变滤波通带的阵列权矢量设计方法。基于简正波理论,结合声场波束形成特点,在分析了常规波束形成信号LOFAR谱图干涉条纹的清晰度和条纹结构不同于单水听器输出信号条纹现象基础上,采用线性等式约束的二次优化模型,给出了一种频率自适应的最优权重估计。数值仿真验证和试验数据分析表明,利用该方法设计的最优权重阵列波束处理,可以滤波出SRBR(Surface-Reflected Bottom-Reflected)或N-SRBR(Non-Surface-Reflected Bottom-Reflected)模态组成的波束形成信号,信号谱图干涉条纹斜率与理论分析基本一致。      

Analysis with binaural auditory model and experiment on the timbre of Ambisonics recording and reproduction

A scheme for analyzing the timbre in spatial sound with binaural auditory model is proposed and the Ambisonics is taken as an example for analysis.Ambisonics is a spatial sound system based on physical sound field reconstruction.The errors and timbre colorations in the final reconstructed sound field depend on the spatial aliasing errors on both the recording and reproducing stages of Ambisonics.The binaural loudness level spectra in Ambisonics reconstruction is calculated by using Moore's revised loudness model and then compared with the result of real sound source,so as to evaluate the timbre coloration in Ambisonics quantitatively.The results indicate that,in the case of ideal independent signals,the high-frequency limit and radius of region without perceived timbre coloration increase with the order of Ambisonics.On the other hand,in the case of recording by microphone array,once the high-frequency limit of microphone array exceeds that of sound field reconstruction,array recording influences little on the binaural loudness level spectra and thus timbre in final reconstruction up to the highfrequency limit of reproduction.Based on the binaural auditory model analysis,a scheme for optimizing design of Ambisonics recording and reproduction is also suggested.The subjective experiment yields consistent results with those of binaural model,thus verifies the effectiveness of the model analysis.     

运动声源识别的动态波叠加方法研究

为更好地识别运动声源并解决声源识别中的虚假声源问题,基于运动声源短时信号的Doppler频移特性, 建立运动声场的短时波叠加关系, 利用波束形成方法对声源点进行预估, 基于预估建立起多运动声源的动态叠加方程, 进一步通过波叠加方程的求解进行声源的计算, 从而创建一种可以用于运动声源识别的动态波叠加方法. 该方法可以有效识别运动声源, 将波叠加方法扩展到了运动声源测量领域, 并在不增加传声器数量以及改变阵列形式的条件下有效抑制运动声源重建中的旁瓣效应, 解决运动声源识别中的虚假声源问题. 仿真及实际运动声源的测量试验结果证明了该方法的有效性.     

Collapse in the Stoner-Wohlfarth noninteracting-particle model

A theory of Mössbauer spectra of noninteracting Stoner-Wohlfarth (SW) particles interacting with rf magnetic fields is developed. The theory makes it possible to calculate the absorption spectra for arbitrary frequency and amplitude of the rf field. The main features of the Stoner-Wohlfarth model are discussed. The Liouville superoperator formalism is used to generalize the results to the case of arbitrarily time-varying hyperfine fields at a nucleus. To understand the qualitative features of the collapse effect that are observed in the Mössbauer spectra of SW particles the particular case of a circularly polarized hyperfine field is studied, and an analytical expression is obtained describing the Mössbauer spectra for this case. An analysis is also made for weak rf magnetic fields and in this case the resonance behavior of the Mössbauer lines is traced as a function of the frequency of the rf field.     

基于声辐射模态的有源结构声传入及其辐射控制

从辐射模态的概念和角度研究利用结构误差传感方法对弹性封闭空间结构声辐射进行传感和有源控制。首先分析了辐射模态的数学和物理意义并揭示了辐射模态与声腔模态之间的内在耦合关系。通过声辐射模态建立了弹性封闭空间结构声辐射传感和有源控制模型,并提出了通过传感器阵列测量结构表面有限点的振速分布和设计特定的辐射模态空间滤波器来获得控制所需的误差信号。在此基础上对封闭空间结构声辐射有源控制和误差传感策略进行了深入的理论和数值仿真分析,重点讨论了传感器的数量和布放对辐射模态传感及其有源控制效果的影响。结果表明:辐射模态与声腔模态的耦合具有严格的选择性,各阶辐射模态的形状和与相耦合的主导声模态在耦合面上的形状非常相似;利用结构传感技术传感封闭空间的辐射模态时测点不足或空间采样不足将可能产生较严重的模态泄漏问题,使得不希望的结构模态泄露进所测的辐射模态当中来。在低频范围内,一般只需传感并最小化前三阶有效辐射模态声势能,在更低频和空间声模态频率附近,只需最小化前一阶最有效辐射模态声势能,便能和总声势能最小化策略控制效果基本一样。