微乳液法制备YF3:Er纳米材料

微乳液[1～2]通常是由表面活性剂、助表面活性剂(通常为醇类)、油(通常为碳氢化合物)和水(或电解质水溶液)组成的透明的、各向同性的热力学稳定体系.微乳液中,微小的水池被表面活性剂所组成的单分子层界面所包围而形成微乳颗粒,其大小可控制在几至几十纳米之间.微小的"水池"尺度小且彼此分离,因而构不成水相,通常称为"微反应器".本文采用了CTAB、正丁醇、正辛烷和水等组成的微乳液体系[3].     

CTAB/CnH2n+1OH/H2O体系的热力学和电化学性质

微乳液通常由表面活性剂、助表面活性剂、油和水等四组分自发生成,注意到表面活性剂、助表面活性剂和水三组分体系与上述四组分体系在相行为及其物理化学性质上具有相似性,为方便起见,人们通常以此三组分体系为对象,研究四组分体系微乳液的有关性质,并亦将其称为微乳液[1].另一方面,助表面活性剂一般为具有中等碳链长度的直链饱和一元醇,但实验已经发现,即使是像乙醇这样的短链醇,也能以相当数量存在于胶束栅栏中形成膜相[2],或存在于两亲双层中形成层状液晶[3].本文以热力学方法与无探针循环伏安法研究了直链饱和一元醇对ＣＴＡＢ/醇(Ｃ2Ｈ…     

阳离子表面活性剂中相微乳的形成和特性

自1943年SdriAn。等人山发现微乳液体系并予以命名以来，对微乳液研究不断深入·微乳液是由油、水、表面活性剂和助表面活性剂组成的各向同性、透明的、热力学稳定的分散体系，微乳液可分为单相微乳液和多相微乳液问．中相微乳液是多相微乳液中，与过剩盐水相和过剩油相达到三相平衡的Winsor皿型微乳液，它在三次采油、日用化工、微环境、酶催化等方面具有特殊重要的应用I‘，‘］．近年来对阴离子表面活性剂中相微乳液的形成和特性进行了较多研究［5。8］．但对阳离子表面活性剂中相微乳液的研究，目前尚未见报导，本文以澳代十四烷基毗…     

农药微乳液物理稳定性的探讨

介绍了微乳液在农药剂型中的研究和应用,分析和探讨了表面活性剂、助表面活性剂、溶剂等组分对微乳形成及物理稳定性的影响。     

Tween80/BmimPF6/醇/甲苯体系的相行为

以环境友好型的Tween80为表面活性剂, 以醇(乙醇、正丁醇、正己醇、正辛醇、正癸醇和异戊醇)为助表面活性剂, 对离子液体1-丁基-3-甲基咪唑六氟磷酸盐(bmimPF6)和甲苯进行了微乳化实验, 绘制了不同条件下Tween80离子液体的微乳体系的拟三元相图, 考察了醇的种类、含量对单相微乳区的影响, 并用电导法研究了在乙醇为助表面活性剂情况下, 单相微乳区的结构转变. 结果表明, 当醇(异戊醇)固定时, 随着表面活性剂/醇的质量比增加, 单相微乳区的面积逐渐增大; 不同链长的直链醇对单相微乳区的面积影响与该醇在离子液体中的溶解情况有关, 单相微乳区的面积随着直链醇链长的增加而越小; 当乙醇作助表面活性剂时, 所得到的单相微乳区的面积最大, 且单相微乳区存在着O/IL(oil-in-ionic liquid)、双连续相和IL/O(ionic liquid-in-oil)三种微结构. 尤其对离子液体微乳体系的电导随油的含量的增加而最初增大的现象进行了解释, 这一现象是由于油主要起到减少离子液体中离子对或离子的积聚, 提高带电离子淌度的作用.     

适用于痕量金属离子迁移的微乳状液的制备及其迁移条件

研究了以气溶胶ＯＴ为表面活性剂与不同烃类的油性溶剂及不同醇类的助表面活性剂一起制备的油包水型微乳为Ｃｄ６２＋从水相或料相迁移到微乳中的影响，同时还观察了油水比和温度对金属离子迁移的影响，从而确定了适于痕量金属离子迁移的微乳体系和和Ｃｄ＾２＋为规范离子的迁移条件。     

以非离子型表面活性剂形成微乳液的碳原子数相关性研究

由非离子型表面活性剂、助表面活性剂（醇）、水和油形成微乳液,用拟三角相图中微乳区的面积确定形成微乳液的最佳条件,实验证明,油的碳原子数加上醇的碳原子数等于表面活性剂的碳原子数对为微乳液形成最佳条件,也符合ＢＳＯ规律。     

Tween80/BmimPF6/醇/甲苯体系的相行为

以环境友好型的Tween80为表而活性剂,以醇(乙醇、正丁醇、正己醇、正辛醇、正癸醇和异戊醇)为助表面活性剂,对离子液体1-丁基-3-甲基咪唑六氟磷酸盐(bmimPF6)和甲苯进行了微乳化实验,绘制了不同条件下Tween80离子液体的微乳体系的拟二元相图,考察了醇的种类、含量对单相微乳区的影响,并用电导法研究了在乙醇为助表面活性剂情况下,单相微乳区的结构转变.结果表明,当醇(异戊醇)固定时,随着表面活性剂/醇的质量比增加,单相微乳区的面积逐渐增大:不同链长的直链醇对单相微乳区的而积影响与该醇在离子液体中的溶解情况有关,单相微乳区的面积随着直链醇链长的增加而越小;当乙醇作助表面活性剂时,所得到的单相微乳区的而积最大,且单相微乳区存在着O/IL(oil-in-ionic liquid)、双连续相和IL/O(ionic liquid-in-oil)三种微结构.尤其对离子液体微乳体系的电导随油的含量的增加而最初增大的现象进行了解释,这一现象是由于油主要起到减少离子液体中离子对或离子的积聚,提高带电离子淌度的作用.     

微乳辅助的溶剂热法合成磷酸钐纳米棒

自1991年碳纳米管被发现以来,一维纳米材料以其独特的电、磁、光学和机械性质以及在纳米器件和功能材料上的巨大应用潜力而引起全世界的广泛关注,人们通过模板法、溶胶-凝胶法、水热法及微乳液法等多种方法合成了一系列一维纳米材料,其中微乳液法是近几年来兴起的较有发展前景的纳米材料的合成方法,微乳液是由油相、水相、表面活性剂和助表面活性剂组成的均匀稳定的体系,水相在表面活性剂和助表面活性剂的作用下均匀地分散在油相中,     

他汀类药物在微乳液相色谱体系中的保留行为

以普伐他汀钠、阿托伐他汀钙、辛伐他汀和洛伐他汀为研究对象,考察了微乳液流动相中表面活性剂的浓度、油相浓度、助表面活性剂浓度以及流动相的pH值等对他汀类药物在微乳液相色谱体系中保留行为的影响。实验结果表明,微乳流动相中表面活性剂、助表面活性剂、亲脂性溶剂的浓度对他汀类药物保留行为的影响与理论模型一致;流动相的pH值对酸性他汀类药物保留行为的影响与理论模型基本一致,对中性他汀类药物保留行为的影响存在着隐函数关系。所建立的保留模型能较好地反映微乳液组成对他汀类药物保留行为的影响。     

A Visible Spectroscopic Study of Microstructure of O/W Microemulsions of Anionic Surfactants: Effect of Cosurfactant

The microstructure of o/w microemulsions, stabilized by sodium dodecyl benzene sulfonate (SDBS) and sodium dodecyl sulfate (SDS) with different cosurfactants, has been studied by partitioning of a dye, phenol red, between the oil‐water interface and bulk water. The cosurfactants used are propan‐1‐ol, propan‐2‐ol, butan‐1‐ol, butan‐2‐ol, pentane‐1‐ol, pentane‐2‐ol, and pentan‐3‐ol. The effects of changing the oil volume fraction and surfactant‐cosurfactant w/w ratio on the oil‐water interface and droplet size have also been discussed. Larger droplet size was predicted for SDS than SDBS. The predicted droplet radius increased with increase in the oil fraction, decrease in the surfactant concentration, increase in the C‐number of the linear cosurfactant, and decrease in branching of the cosurfactant. Surfactant‐cosurfactant ratio and pH did not affect the droplet size significantly. The minimum concentrations of surfactants with which microemulsions were formed were found to be higher for larger oil fraction, smaller C‐number of the alcohol, more branching of the alcohol, and higher pH.     

Structural and spectroscopic investigation of ZnS nanoparticles grown in quaternary reverse micelles

ZnS nanoparticles were synthesized in four component "water in oil" microemulsions formed by a cationic surfactant (cetyltrimethylammonium bromide, CTAB), a cosurfactant (pentanol or butanol), n-hexane and water. The effect of various parameters (nature of cosurfactant, water/surfactant W(0), and alcohol/surfactant P(0)) on the formation and stability of ZnS nanoparticles was investigated thoroughly. UV-Vis spectroscopy was employed to directly follow the formation of ZnS systems in the microemulsions. Thus, particle size was estimated from the position of the first excitonic transition by employing an approximate finite-depth equation and an empirical correlation, giving average diameters in the ranges 2.3-2.5 and 3.0-3.5nm, respectively. Stable ZnS nanoparticles were obtained by employing low water and high cosurfactant amounts. This suggests that at high concentration the cosurfactant molecules act as capping agents on the surface of the inverse micelles, while low water amounts are needful to obtain water droplets with a radius close to that of the interfacial film spontaneous curvature. HRTEM analysis showed that the samples are formed by a few crystalline ZnS nanoparticles of spherical shape, embedded in and amorphous organic matrix, with a coherent scattering domain between 2 and 4nm.     

Microemulsions: Effect of alkyl chain length of alcohol and alkane

In microemulsions consisting of four components, i.e. detergent — water — oil — cosurfactant, the free energy of transfer from the continuous oil phase to the interfacial region for the cosurfactant is reported. From the effect of temperature on the free energy, the entropy and the enthalpy values are also reported. The effect of chain length of the alcohol (cosurfactant) is also described. It is further shown, that if the oil phase consists of hexadecane, then the free energy changes as a linear function of the number of carbon atoms in the cosurfactant. On the other hand, if the oil phase is benzene, the cosurfactant chain length has very little effect. These data are analyzed with respect to the microemulsion structure and stability.     

阳离子表面活性剂混合胶团对2,4-二硝基氯苯水解反应的 催化作用

研究了阳离子表面活性剂混合胶团对2,4-二硝基氯苯(DNCB)碱性水解反应的催化作用。结果表明：(1)在十六烷基三甲基溴化铵(CTAB)和十六烷基溴化吡啶(CPB)混合溶液中DNCB水解一级速率常数k1与混合胶团中CTAB或CPB的摩尔分数有直线关系,表面活性剂形成理想的混合胶团。(2)辛基三甲基省化铵(OTAB)与CTAB,CPB的cmc值相差很大,在它们的混合胶团中OTAB含量极少,DNCB水解k1与CPB/OTAB混合胶团中CPB摩尔分数的关系与直线呈负偏差。(3)在CTAB(或CPB)与OTAB混合体系中OTAB起溴盐作用,使催化活性降低。用假相离子交换(PIE)模型对所得结果给出了定量的处理和解释。     

Study of nano-emulsion formation by dilution of microemulsions

The influence of different dilution procedures on the properties of oil-in-water (O/W) nano-emulsions obtained by dilution of oil-in-water (O/W) and water-in-oil (W/O) microemulsions has been studied. The system water/SDS/cosurfactant/dodecane with either hexanol or pentanol as cosurfactant was chosen as model system. The dilution procedures consisted of adding water (or microemulsion) stepwise or at once over a microemulsion (or water). Starting emulsification from O/W microemulsions, nano-emulsions with droplet diameters of 20 nm are obtained, independently on the microemulsion composition and the dilution procedure used. In contrast, starting emulsification from W/O microemulsions, nano-emulsions are only obtained if the emulsification conditions allow reaching the equilibrium in an O/W microemulsion domain during the process. These conditions are achieved by stepwise addition of water over W/O microemulsions with O/S ratios at which a direct microemulsion domain is crossed during emulsification. The nature of the alcohol used as cosurfactant has been found to play a key role on the properties of the nano-emulsions obtained: nano-emulsions in the system using hexanol as cosurfactant are smaller in size, lower in polydispersity, and have a higher stability than those with pentanol.     

Background and operating parameters in microemulsion electrokinetic chromatography

Microemulsion electrokinetic chromatography (MEEKC) is an electrodriven separation technique. Separations are generally achieved using microemulsions consisting of surfactant-coated nanometer-sized oil droplets suspended in aqueous buffer. A cosurfactant such as a short-chain alcohol is generally used to stabilize the microemulsion. This review summarizes the various microemulsion types and compositions that have been used in MEEKC. The effects of key-operating variables such as surfactant type and concentration, cosurfactant type and concentration, buffer pH and type, oil type and concentration, use of organic solvent and cyclodextrin additions, and temperature are described. Specific examples of water-in-oil microemulsions and chirally selective separations are also covered.     

MICROEMULSION SYSTEMS WITH A NONIONIC COSURFACTANT

The conditions to obtain W/0 microemulsions using ionic surfactants and a nonionic cosurfactant, a polyoxyethylene alkyl ether, were investigated. The length of the polyoxyethylene chain was critical to obtain the typical water solubilization maximum

The variation of the W/0 microemulsion region with hydrocarbon content was different from that of the usual type of microemulsions having a medium chain length alcohol as cosurfactant. In the present systems the W/0 microemulsion region was not a direct continuation of the inverse micellar area at zero content of hydrocarbon. Addition of hydrocarbon was necessary for the formation of inverse micelles

The microemulsion regions were sensitive to the kind of hydrocarbon used; a sign of the importance of the nonionic surfactant for the stability of this kind of microemulsions.     

Recent advances in microemulsion electrokinetic chromatography

Microemulsion electrokinetic chromatography (MEEKC) is an electrodriven separation technique. Separations are typically achieved using oil-in-water microemulsions, which are composed of nanometre-sized droplets of oil suspended in aqueous buffer. The oil droplets are coated in surfactant molecules and the system is stabilised by the addition of a short-chain alcohol cosurfactant. The novel use of water-in-oil microemulsions for MEEKC separations has also been investigated recently. This report summarises the different microemulsion types and compositions used to-date and their applications with a focus on recent papers (2002-2004). The effects of key operating variables (pH, surfactant, cosurfactant, oil phase, buffer, additives, temperature, organic modifier) and methodology techniques are described.     

ALTERNATIVE COSURFACTANTS AND COSOLVENTS TO PREPARE MICROEMULSIONS SUITABLE FOR PRACTICAL APPLICATIONS

Some examples of systems including useful ingredients as cosurfactants and cosolventsto furnish suitable microemulsions to be applicated in technological fields such as cosmetics and dermopharmaceuticals, are given For systems with ionic surfactants, the usual cosurfactant (medium chain lenght alcohol) was substituted by more skin compatible ingredients as butyl lactate, or alternatively by oleic acid and a glycol as cosolvent mixed in the aqueous phase of the system. On the other hand, for a system with an alkyl glucoside as nonionic surfactant, temperature - insensitive microemulsions was obtained also with butyl lactate as cosurfactant. Moreover, the influence that the presence of glycols as cosolvents involve on the isotropic liquid regions of such systems has been also evidenced. In conclusion, it is possible to formulate suitable microemulsions to practical applications, overcoming the traditional problems of the most of the conventional microemulsions as are the biological agressivity of the cosurfactant for ionic surfactant systems, and the temperature dependence for nonionic surfactant systems.     

Micellar-catalyzed alkaline hydrolysis of 2,4-dinitrochlorobenzene in a cationic gemini surfactant

Micellar-catalyzed alkaline hydrolysis of 2,4-dinitrochlorobenzene (DNCB) in the presence of a conventional cationic surfactant CTAB or a cationic gemini surfactant 1,2-ethane bis(dimethyldodecylammonium bromide) (12-2-12) were studied spectrophotometrically at 25 °C. It was found that both CTAB and 12-2-12 micelles accelerated the alkaline hydrolysis of DNCB, and the binding constant of the substrate to the micelle, K_S, for 12-2-12 (K_S = 310 M⁻¹) was larger than that for CTAB (85 M⁻¹), which suggested that DNCB molecules bound with gemini micelles more easily than with CTAB. However, the second-order rate constant in micellar pseudophase (k_M = 1.22 × 10⁻³ s⁻¹) for 12-2-12 was lower than k_M for CTAB (4.01 × 10⁻³ s⁻¹) because the substrate may enter the interior of the 12-2-12 micelles. It was found also that 12-2-12 had a similar catalysis mechanism to CTAB when the concentration of 12-2-12 was relatively low (ca. <5 mM). However, above this concentration, higher microviscosity and significant increases in aggregation number and micelle size with increased surfactant concentration may remarkably influence the hydrolysis reaction.