活性炭负载TiO2光催化氧化二苯并噻吩的研究

以活性炭负载的TiO2为光催化剂,H2O2为氧化剂,30W紫外灯为光源,对含二苯并噻吩（DBT）的模型硫化物进行光催化氧化脱硫研究。考察了TiO2的煅烧温度、负载量、催化剂用量、H2O2用量和光照时间对DBT去除率的影响。实验结果表明,用溶胶 凝胶法制备的TiO2 /活性炭催化剂对DBT具有很好的光催化效果。最佳反应条件为,催化剂煅烧温度400℃,TiO2的负载量为32％,催化剂用量0.7g/100mL, H2O2最佳用量为10mL,即O/S（摩尔比）为14。在最佳反应条件下,光照时间8h,DBT去除率为90％, 此反应为一级动力学反应。     

CuOx/TiO2光催化水蒸气还原CO2

以商品TiO2-P25为原料,通过浸渍法负载一定量过渡金属Cu,得到一系列不同含量的CuOx/TiO2光催化剂。利用X射线衍射（XRD）,X－射线光电子能谱（XPS）,BET,高分辨率透射镜（HRTEM）,X射线荧光光谱（XRF）和光致发光光谱（PL）等方法对催化剂进行了详细表征,在自建的光催化反应器中评价了气态水光催化还原CO2反应的活性和CH4收率。结果表明负载CuOx后的TiO2纳米材料光催化性能显著提高,其中1%CuOx/TiO2样品紫外光照72 h后,CH4生成量达到了24.86 µmol•gTi-1。同时,CuOx负载量、反应温度、反应时间等因素对CH4收率均有显著影响。     

复合材料K_8[Fe(H_2O)CdW_(11)O_(39)]/PANI/ZrO_2的制备、表征及光催化性能

采用静电自组装法制备了复合材料K_8[Fe(H_2O)CdW_(11)O_(39)]/PANI/ZrO_2.运用UV,IR,XRD,SEM-EDS和N_2吸附-脱附的检测手段对其进行了表征,并以该化合物作为催化剂,研究了其对孔雀石绿溶液的光降解情况.通过实验确定最佳的光降解条件:孔雀石绿溶液的初始浓度为25mg/L,孔雀石绿溶液的初始pH值为2,K_8[Fe(H_2O)CdW_(11)O_(39)]/PANI/ZrO_2的用量为0.05g.在最佳的条件下,孔雀石绿溶液的脱色率可达98.68%.因此,K_8[Fe(H_2O)CdW_(11)O_(39)]/PANI/ZrO_2是一种光催化性能良好的复合材料.     

Length-controlled synthesis of oriented single-crystal rutile TiO2 nanowire arrays

A free-standing, large area, oriented single-crystal rutile TiO(2) nanowire arrays with a controlled length in the range of 10-80 μm are prepared via a facile one-step synthesis. The growth process is studied systematically in an appropriate amount of H(2)O(2) and HCl solution under hydrothermal conditions. The length of the nanowires can be easily tuned by varying the experimental parameters, including reaction temperature and reaction time. High-resolution transmission electron microscopy demonstrated that the nanowires have single-crystal structure. Furthermore, the photoluminescence characteristics and photocatalytic properties of oriented single-crystal rutile TiO(2) nanowires was discussed in this paper, respectively. It is found that the increased reaction temperature is helpful to photocatalytic reactivity and photoluminescence properties.     

Synthetic architectures of TiO2/H2Ti5O11.H2O, ZnO/H2Ti5O11.H2O, ZnO/TiO2/H2Ti5O11.H2O, and ZnO/TiO2 nanocomposites

Although synthetic investigations of inorganic nanomaterials had been carried out extensively over the past decade, few of them have been devoted to fabrication of complex nanostructures that comprise multicomponents/phases (i.e., composite nanobuilding blocks), especially in the area of structural/morphological architecture. In this work, nanobelts of a protonated pentatitanate (H(2)Ti(5)O(11).H(2)O) were synthesized hydrothermally for the first time. Two technologically important transition-metal-oxides TiO(2) and ZnO were then grown respectively or sequentially onto the surface of the as-prepared nanobelts in aqueous mediums. With a main emphasis on organizational manipulation, the present investigation examines general issues of morphological complexity, synthetic interconvertibility, and material combinability related to fabrication of inorganic nanocomposites. Using this model material system, we demonstrate that complex binary and tertiary composite building blocks of TiO(2)/H(2)Ti(5)O(11).H(2)O, ZnO/H(2)Ti(5)O(11).H(2)O, ZnO/TiO(2)/H(2)Ti(5)O(11).H(2)O, and ZnO/TiO(2) can be architected stepwise in solution. Structural features of these nanocomposites have also been addressed.     

Sustained production of H2O2 on irradiated TiO2- fluoride systems

UV irradiation of fluorinated TiO(2) suspensions in water, in the presence of oxygen and a hole scavenger, leads to the production of H(2)O(2) with steady state concentration levels up to 1.3 millimolar; the H(2)O(2) formation rate follows the TiO(2) surface speciation, being maximum when the surface is completely covered by [triple bond]Ti-F groups; these results outline the importance of surface speciation on the photocatalytic process.     

盐卤硼酸盐化学XIII;2MgO.2B2O3. Mgcl2.14H2O结晶动力学研究

本发明对MgO-B2O-MgCl2-H2O浓盐溶液结晶析出氯柱硼镁石(αMgO,αB2O3MgCl.14H2O)的动力学过程进行了研究, 利用单纯形优化法配合Runge-Kutta微分方程组数值解法对实验数据进行处理, 给出了结晶动力学方程, 并对硼在溶液中的存在形式进行了讨论, 提出了结晶反应机理, 同时考察了温度和氯化镁浓度对结晶速率的影响。     

以十二烷基苯磺酸钠为模型反应物的Y2O3/TiO2复合催化剂的制备及光降解催化性能

采用浸渍法制备了Y₂O₃/TiO₂复合氧化物催化剂,并用紫外可见光谱、SEM、BET等手段对其进行了表征.以水相十二烷基苯磺酸钠(DBS)溶液的光催化降解反应为实验模型,考察了TiO₂掺杂Y₂O₃后的光催化氧化活性,并探讨了Y₂O₃掺杂量、吸附性、焙烧温度及时间对Y₂O₃/TiO₂复合氧化物催化剂光催化活性的影响.实验结果表明:复合氧化物催化剂Y₂O₃/TiO₂存在某一最佳组分比值,当两者重量比为1:200时,其催化活性是同样条件下前体催化剂TiO₂的2.4倍.     

O2 interaction and reactivity on a model hydroxylated rutile(110) surface

Recently several theoretical studies have examined oxygen adsorption on the clean, reduced TiO2(110) surface. However the photocatalytic behavior of TiO2 and the scavenging ability of oxygen are known to be influenced by the presence of surface hydroxyls. In this paper the chemistry of O2 on the hydroxylated TiO2 surface is investigated by means of first-principles total energy calculations and molecular dynamics (MD) simulations. The MD trajectories show a direct, spontaneous reaction between O2 and the surface hydroxyls, thus supporting the experimental hypothesis that the reaction does not necessarily pass through a chemisorbed O2 state. Following this reaction, the most stable chemisorbed intermediates are found to be peroxide species HO2 and H2O2. Although these intermediates are very stable on the short time scale of MD simulations, the energetics suggests that their further transformation is connected to a new 300 K feature observed in the experimental water temperature programmed desorption (TPD) spectrum. The participation of two less stable intermediate states, involving terminal hydroxyls and/or chemisorbed water plus oxygen adatoms, to the desorption process, is not supported by the total energy calculations. Analysis of the projected density of states, however, suggests the possibility that these intermediates have a role in completing the surface oxidation immediately before desorption.     

SO2-4/TiO2固体酸催化剂的酸强度及光催化性能

SO2-4/TiO2固体酸可用于光催化降解溴代甲烷,其光催化性能明显优于TiO2光催化剂.在相同反应条件下,SO2-4/TiO2的光催化活性比TiO2提高2～10倍.当H2SO4浸渍液浓度为1mol/L时,制得的SO2-4/TiO2酸性最强(H0＜-12.14),具有超强酸性和最高的光催化活性.     

在TiO2上CO的光催化氧化

最近在“氧化的”TiO₂(即表面无氧空位和Ti³⁺)上进行的CO光催化氧化研究发现:室温下,以黑光灯(峰值λ=365nm)光照时,“氧化的”TiO₂无CO催化氧化的活性,但以杀菌灯(峰值λ=253.7nm)光照时,则对CO产生显著的催化活性.参照CO在过渡金属表面的催化氧化机理,对本现象进行了解释:黑光灯照时,O₂在TiO₂表面只生成O_2(a)^-,而O_2(a)^-不能使CO氧化,只有以杀菌灯照时,TiO₂表面产生O_(a)^-,CO氧化反应才能发生.     

Reaction of [RuIII(edta)(H2O)]- with H2O2 in aqueous solution. Kinetic and mechanistic investigation

The reaction of [Ru(III)(edta)(H(2)O)](-) (1) (edta = ethylenediaminetetraacetate) with hydrogen peroxide was studied kinetically as a function of [H(2)O(2)], temperature (5-35 degrees C) and pressure (1-1300 atm) at a fixed pH of 5.1 using stopped-flow techniques. The reaction was found to consist of two steps involving the rapid formation of a [Ru(III)(edta)(OOH)](2-) intermediate which subsequently undergoes parallel heterolytic and homolytic cleavage to produce [(edta)Ru(V)=O](-) (45%) and [(edta)Ru(IV)(OH)](-) (55%), respectively. The water soluble trap, 2,2'-azobis(3-ethylbenzithiazoline-6-sulfonate) (ABTS), was employed to substantiate the mechanistic proposal. Reactions were carried out under pseudo-first conditions for [ABTS] > [HOBr] > [1], and were monitored as a function of time for the formation of the one-electron oxidation product ABTS* (+). A detailed mechanism in agreement with the rate and activation parameters is presented, and the results are discussed with reference to data reported for the corresponding [Fe(III)(edta)(H(2)O)](-)/H(2)O(2) system.     

Heterogeneous Interaction of H(2)O(2) with TiO(2) Surface under Dark and UV Light Irradiation Conditions

The heterogeneous interaction of H(2)O(2) with TiO(2) surface was investigated under dark conditions and in the presence of UV light using a low pressure flow tube reactor coupled with a quadrupole mass spectrometer. The uptake coefficients were measured as a function of the initial concentration of gaseous H(2)O(2) ([H(2)O(2)](0) = (0.17-120) × 10(12) molecules cm(-3)), irradiance intensity (J(NO(2)) = 0.002-0.012 s(-1)), relative humidity (RH = 0.003-82%), and temperature (T = 275-320 K). Under dark conditions, a deactivation of TiO(2) surface upon exposure to H(2)O(2) was observed, and only initial uptake coefficient of H(2)O(2) was measured, given by the following expression: γ(0)(dark) = 4.1 × 10(-3)/(1 + RH(0.65)) (calculated using BET surface area, estimated conservative uncertainty of 30%) at T = 300 K. The steady-state uptake coefficient measured on UV irradiated TiO(2) surface, γ(ss)(UV), was found to be independent of RH and showed a strong inverse dependence on [H(2)O(2)] and linear dependence on photon flux. In addition, slight negative temperature dependence, γ(ss)(UV) = 7.2 × 10(-4) exp[(460 ± 80)/T], was observed in the temperature range (275-320) K (with [H(2)O(2)] ≈ 5 × 10(11) molecules cm(-3) and J(NO(2)) = 0.012 s(-1)). Experiments with NO addition into the reactive system provided indirect evidence for HO(2) radical formation upon H(2)O(2) uptake, and the possible reaction mechanism is proposed. Finally, the atmospheric lifetime of H(2)O(2) with respect to the heterogeneous loss on mineral dust was estimated (using the uptake data for TiO(2)) to be in the range of hours during daytime, i.e., comparable to H(2)O(2) photolysis lifetime (～1 day), which is the major removal process of hydrogen peroxide in the atmosphere. These data indicate a strong potential impact of H(2)O(2) uptake on mineral aerosol on the HO(x) chemistry in the troposphere.     

2DFT Research of the Interaction between Metal Ions and CO2 along with H2O

The interaction between several different metal ions and H2O along with CO2 has been researched theoretically in the CO2 photocatalytic reduction with H2O system at the B3LYP level by DFT.The computational results revealed that relatively high valence metal ions loaded on TiO2 activated the H2O and CO2 consumingly,and it might be looked as some proofs for modified photocatalyst selecting.In addition,the metal ions conducted photoelectrons to prevent the re-combination of photoelectrons and holes during the reaction process.     

纳米SnO2@TiO2包覆催化剂的制备及表征

采用活性层包覆法在自制细SnO2胶体粒子表面包覆TiO2,制备出SnO2@TiO2包覆型复合催化剂,以其对有机磷农药DDVP的降解效果作为评价光催化活性的标准,对制备条件进行了优化,并用XRD、TEM和BET等手段对样品进行了表征,结果表明,SnO2胶体乙醇溶液含水量20％,钛酸丁酯质量分数为34.5％。灼烧温度680℃时制得TiO2含量56.45％的包覆样品SnO2@TiO2为纳米级粒子,且其光催化活性最佳。     

CuOx/TiO2光催化水蒸气还原CO2反应研究

以商品TiO2-P25为原料,通过浸渍法负载一定量过渡金属Cu,得到一系列不同含量的CuOx/TiO2光催化剂.利用X射线衍射(XRD),X-射线光电子能谱(XPS),BET,高分辨率透射镜(HRTEM),X射线荧光光谱(XRF)和光致发光光谱(PL)等方法对催化剂进行了详细表征,在自建的光催化反应器中评价了气态水光催化还原CO2反应的活性和CH4收率.结果表明负载CuOx后的TiO2纳米材料光催化性能显著提高,其中1%CuOx/TiO2样品紫外光照72 h后,CH4生成量达到了24.86μmol.gTi-1.同时,CuOx负载量、反应温度、反应时间等因素对CH4收率均有显著影响.     

Detection of H2O2 released from TiO2 photocatalyst to air.

H2O2 generated and released from TiO2 photocatalysts to the gas phase was detected. A flow-through cell packed with TiO2-coated glass beads was irradiated with UV light, and the gas flowing out of the cell was flushed through a collecting solution containing 2,2'-azino-bis(3-ethylbenzothiazoline-6-sulforic acid) diammonium salt (ABTS) and peroxidase. Oxidative coloration of ABTS was observed only in the absence of catalase, indicating the presence of H2O2 in the gas. The quantum yield of the H2O2 generation was estimated to be > 1 x 10(-7). The detected amount of H2O2 decreased as the TiO2 thickness decreased. H2O2 was not detected when dry air or nitrogen was used.     

Kinetics of Al + H2O reaction: theoretical study

Quantum chemical calculations were carried out to study the reaction of Al atom in the ground electronic state with H(2)O molecule. Examination of the potential energy surface revealed that the Al + H(2)O → AlO + H(2) reaction must be treated as a complex process involving two steps: Al + H(2)O → AlOH + H and AlOH + H → AlO + H(2). Activation barriers for these elementary reaction channels were calculated at B3LYP/6-311+G(3df,2p), CBS-QB3, and G3 levels of theory, and appropriate rate constants were estimated by using a canonical variational theory. Theoretical analysis exhibited that the rate constant for the Al + H(2)O → products reaction measured by McClean et al. must be associated with the Al + H(2)O → AlOH + H reaction path only. The process of direct HAlOH formation was found to be negligible at a pressure smaller than 100 atm.     

Mechanism of photoinduced superhydrophilicity on the TiO2 photocatalyst surface

The physicochemical properties of the H(2)O molecules adsorbed on TiO(2) surfaces during UV light irradiation were fully investigated by near-infrared (NIR) absorption spectroscopy. It was found that the H(2)O molecules adsorbed on the TiO(2) surfaces desorb during UV light irradiation by the heating effect of the light source. Since the amount of the H(2)O adsorbed on the TiO(2) surfaces decreased, the distribution of the hydrogen bonds within the H(2)O molecules decreased, resulting in a decrease in the surface tension of the H(2)O clusters. The decrease in the surface tension of H(2)O under UV light irradiation was found to be one of the most important driving forces in which the H(2)O clusters on the TiO(2) surface spread out thermodynamically, forming H(2)O thin layers. The partial elimination of the hydrocarbons from the TiO(2) surface by the photocatalytic complete oxidation was seen to be the other important factor, providing free spaces on the surface where the H(2)O clusters could spill over and spread out to form the thin H(2)O layers. Moreover, the temperature changes of the TiO(2) powder samples during UV light irradiation were found to show a good correspondence with the changes in the contact angle of the H(2)O droplets on the TiO(2) thin film surfaces. Especially the time scale for the hydrophilic conversion on the TiO(2) surfaces under UV light irradiation was in good agreement with the decrease in the amount of H(2)O molecules adsorbed on the TiO(2) surfaces but not the amount of the hydrocarbons eliminated by the photocatalytic oxidation reactions, showing that the adsorption and desorption of H(2)O molecules are generally quite sensitive to the temperature changes of solid surfaces.     

孔道结构H3PW12O40/TiO2的制备及其可见光光催化降解水溶性染料的性能

 采用溶胶-凝胶方法制备了孔道结构复合材料H3PW12O40/TiO2,采用ICP-AES,UV/DRS,31P MAS NMR,TEM和N2吸附等技术对其组成和结构进行了表征. 结果表明,催化剂中活性组分H3PW12O40的基本骨架结构未发生改变,H3PW12O40的担载量为22.29%,催化剂平均粒径为40 nm,具有双孔结构,其平均微孔和介孔孔径分别为0.61和3.06 nm. 考察了催化剂可见光光催化降解6种水溶性染料的性能. 结果表明,6种染料均可不同程度地被降解和矿化. 通过对染料中性红的光催化降解实验,比较了H3PW12O40/TiO2,Degussa P-25和锐钛矿结构TiO2的可见光光催化活性,其中,H3PW12O40/TiO2活性最高,且催化剂最易分离,可循环使用.