4,4′-Diaminodiphenylsulfone; an efficient co-additive in dye-sensitized nanocrystalline TiO2 solar cells

The effect of 4,4′-diaminodiphenylsulfone (DADPS) as a co-additives in iodide/triiodide redox electrolyte on the performance of dye-sensitized solar cell based on the 2-cyano-3-(4-(diphenylamino)phenyl)acrylic acid (TPA) and 2-cyano-3-(2΄-(5΄,10΄,15΄,20΄- tetraphenylporphyrinato Zinc (II)yl) acrylic acid (Zn-1) dyes have been investigated. Compared withstandard electrolyte (0.1 M LiI, 0.05 M I₂, 0.6 M 1-butyl-2,3-dimethylimidazolium iodide (BDMII) and TBP (0.5, 1 M)), adding 0.5 M of DADPS, as a co-additive, into the electrolyte system has caused increasing short current density (J_sc) and open-circuit potential (V_oc) consequently the energy conversion (η) improved. Electrochemical impedance results indicate adsorbing of DADPS on the titanium dioxide surface leads to an increase in the lifetime (τ). Adsorbing of DADPS on the semiconductor surface retards the interfacial charge recombination that has a beneficial effect on the V_oc and J_sc. The results showed that amine groups of DADPS attach to the conduction band (CB) of TiO₂ film and suppress the electron recombination process and as a result, it can be applied as a promising co-additive in DSSCs.     

Role of electrolytes on charge recombination in dye-sensitized TiO(2) solar cell (1): the case of solar cells using the I(-)/I(3)(-) redox couple

Performance of dye-sensitized solar cells (DSCs) was investigated depending on the compositions of the electrolyte, i.e., the electrolyte with a different cation such as Li(+), tetra-n-butylammonium (TBA(+)), or 1,2-dimethyl-3-propylimidazolium (DMPIm(+)) in various concentrations, with and without 4-tert-butylpyridine (tBP), and with various concentrations of the I(-)/I(3)(-) redox couple. Current-voltage characteristics, electron lifetime, and electron diffusion coefficient were measured to clarify the effects of the constituents in the electrolyte on the charge recombination kinetics in the DSCs. Shorter lifetimes were found for the DSCs employing adsorptive cations of Li(+) and DMPIm(+) than for a less-adsorptive cation of TBA(+). On the other hand, the lifetimes were not influenced by the concentrations of the cations in the solutions. Under light irradiation, open-circuit voltages of DSCs decreased in the order of TBA(+)> DMPIm(+) > Li(+), and also decreased with the increase of [Li(+)]. The decreases of open-circuit voltage (V(oc)) were attributed to the positive shift of the TiO(2) conduction band potential (CBP) by the surface adsorption of DMPIm(+) and Li(+). These results suggest that the difference of the free energies between that of the electrons in the TiO(2) and of I(3)(-) has little influence on the electron lifetimes in the DSCs. The shorter lifetime with the adsorptive cations was interpreted with the thickness of the electrical double layer formed by the cations, and the concentration of I(3)(-) in the layer, i.e., TBA(+) formed thicker double layer resulting in lower concentration of I(3)(-) on the surface of the TiO(2). The addition of 4-tert-butylpyridine (tBP) in the presence of Li(+) or TBA(+) showed no significant influence on the lifetime. The increase of V(oc) by the addition of tBP into the electrolyte containing Li(+) and the I(-)/I(3)(-) redox couple was mainly attributed to the shift of the CBP back to the negative potential by reducing the amount of adsorbed Li cations.     

Significant efficiency improvement of the black dye-sensitized solar cell through protonation of TiO2 films

This paper describes the influence of acid pretreatment ofTiO2 mesoporous films prior to dye sensitization on the performance of dye-sensitized solar cells based on [(C4H9)4N]3[Ru(Htcterpy)(NCS)3] (tcterpy = 4,4',4"-tricarboxy- 2,2',2"-terpyridine), the so-called black dye. The HCl pretreatment caused an increase in overall efficiency by 8%, with a major contribution from photocurrent improvement. It is speculated, from the analysis of incident photon-to-electron conversion efficiency, UV-vis absorption spectra, redox properties of the dye and TiO2, and the impedance spectra of the dye-sensitized solar cells, that photocurrent enhancement is attributed to the increases in electron injection and/or charge collection efficiency besides the improvement of light harvesting efficiency upon HCl pretreatment. Open-circuit photovoltage (V(oc)) remained almost unchanged in the case of significant positive shift of flat band potential for TiO2 upon HCl pretreatment. The suppression of electron transfer from conduction band electrons to the I3- ions in the electrolyte upon HCl pretreatment, reflected by the increased resistance at the TiO2/dye/electrolyte interface and reduced dark current, resulted in a V(oc) gain, which compensated the V(oc) loss due to the positive shift of the flat band. Using the HCl pretreatment approach, 10.5% of overall efficiency with the black dye was obtained under illumination of simulated AM 1.5 solar light (100 mW cm(-2)) using an antireflection film on the cell surface.     

Influence of a TiCl4 post-treatment on nanocrystalline TiO2 films in dye-sensitized solar cells

In this study, the influence of the TiCl(4) post-treatment on nanocrystalline TiO(2) films as electrodes in dye-sensitized solar cells is investigated and compared to nontreated films. As a result of this post-treatment cell efficiencies are improved, due to higher photocurrents. On a microscopic scale TiO(2) particle growth on the order of 1 nm is observed. Despite a corresponding decrease of BET surface area, more dye is adsorbed onto the oxide surface. Although it seems trivial to match this finding with the improved photocurrent, this performance improvement cannot be attributed to higher dye adsorption only. This follows from comparison between incident photon to current conversion efficiency (IPCE) and light absorption characteristics. Since the charge transport properties of the TiO(2) films are already more than sufficient without treatment, the increase in short circuit current density J(SC) cannot be related to improvements in charge transport either. Transient photocurrent measurements indicate a shift in the conduction band edge of the TiO(2) upon TiCl(4) treatment. It is concluded that the main contribution to enhanced current originates from this shift in conduction band edge, resulting in improved charge injection into the TiO(2).     

Electrochemical impedance spectroscopic analysis of dye-sensitized solar cells

Electrochemical impedance spectroscopy (EIS) has been performed to investigate electronic and ionic processes in dye-sensitized solar cells (DSC). A theoretical model has been elaborated, to interpret the frequency response of the device. The high-frequency feature is attributed to the charge transfer at the counter electrode while the response in the intermediate-frequency region is associated with the electron transport in the mesoscopic TiO2 film and the back reaction at the TiO2/electrolyte interface. The low-frequency region reflects the diffusion in the electrolyte. Using an appropriate equivalent circuit, the electron transport rate and electron lifetime in the mesoscopic film have been derived, which agree with the values derived from transient photocurrent and photovoltage measurements. The EIS measurements show that DSC performance variations under prolonged thermal aging result mainly from the decrease in the lifetime of the conduction band electron in the TiO2 film.     

新型梳状共聚物在准固态染料敏化太阳能电池中的应用及其对电子复合的影响

合成了乙烯基咪唑碘盐(VImI)和聚乙二醇单甲醚甲基丙烯酸酯(PEGMA)的梳状共聚物.利用VImI/PEGMA共聚物制备了准固态聚合物电解质.通过光电流密度-电压(J-V)曲线和电导率测定以及电化学阻抗分析,探讨了基于此电解质的染料敏化太阳能电池的电荷传输与界面电子转移机制.结果表明,VImI/PEGMA共聚物可以有效抑制TiO2/电解质界面电子复合并提高TiO2导带能级,敏化电池的光伏性能并不完全取决于电解质的电导率.通过考察共聚物中VImI与PEGMA单元的摩尔比与开路电压的关系,发现共聚物对电子复合的抑制作用主要源于VImI链段.此外,开路电压衰减(OCVD)和瞬态光电流测试结果说明,共聚物能够提高TiO2薄膜的电子寿命,而且对陷阱电子能级的分布具有调节作用.当共聚物在电解质中的质量分数为50%,VImI与PEGMA的摩尔比为5.0时,准固态染料敏化太阳能电池于100mW·cm-2光强下获得了4.10%的光电转换效率.     

DFT description on electronic structure and optical absorption properties of anionic S-doped anatase TiO2

Plane-wave-based pseudopotential density functional theory (DFT) calculations are used to characterize the doping effect of S substituting for O in anatase TiO(2). Through band structure calculation, a direct band gap is predicted in TiO(2)(-)(x)S(x). Electronic structure analysis shows that the doping S could substantially lower the band gap of TiO(2) by the presence of an impurity state of S 3p on the upper edge of the valence band. Excitations from the impurity state of S 3p to the conduction band may be responsible for the red shift of the absorption edge observed in the S-doped TiO(2). The band gap lowering and red shift of the absorption edge are found to increase as the sulfur concentration increases.     

Effect of solvent and additives on the open-circuit voltage of ZnO-based dye-sensitized solar cells: a combined theoretical and experimental study

We have investigated the role of electrolyte composition, in terms of solvent and additive, on the open-circuit voltage (V(oc)) of ZnO-based dye-sensitized solar cells (DSSCs) using a combined experimental and theoretical approach. Calculations based on density functional theory (DFT) have been performed in order to describe the geometries and adsorption energies of various adsorbed solvents (nitromethane, acetonitrile and dimethylformamide) and p-tert-butylpyridine (TBP) (modeled by methylpyridine) on the ZnO (100) surface using a periodic approach. The densities of states (DOS) have been calculated and the energy position of the conduction band edge (CBE) has been evaluated for the different molecules adsorbed. The effect of the electrolyte composition on the standard redox potential of the iodide/triiodide redox couple has been experimentally determined. These two data values (CBE and standard redox potential) allowed us to determine the dependence of V(oc) on the electrolyte composition. The variations determined using this method were in good agreement with the measured V(oc) for cells made of electrodeposited ZnO films sensitized using D149 (indoline) dye. As in the case of TiO(2)-based cells, a correlation of V(oc) with the donor number of the adsorbed species was found. The present study clearly points out that both the CBE energy and the redox potential variation are important for explaining the experimentally observed changes in the V(oc) of DSSCs.     

Lithium-modulated conduction band edge shifts and charge-transfer dynamics in dye-sensitized solar cells based on a dicyanamide ionic liquid

Lithium ions are known for their potent function in modulating the energy alignment at the oxide semiconductor/dye/electrolyte interface in dye-sensitized solar cells (DSCs), offering the opportunity to control the associated multichannel charge-transfer dynamics. Herein, by optimizing the lithium iodide content in 1-ethyl-3-methylimidazolium dicyanamide-based ionic liquid electrolytes, we present a solvent-free DSC displaying an impressive 8.4% efficiency at 100 mW cm(-2) AM1.5G conditions. We further scrutinize the origins of evident impacts of lithium ions upon current density-voltage characteristics as well as photocurrent action spectra of DSCs based thereon. It is found that, along with a gradual increase of the lithium content in ionic liquid electrolytes, a consecutive diminishment of the open-circuit photovoltage arises, primarily owing to a noticeable downward movement of the titania conduction band edge. The conduction band edge displacement away from vacuum also assists the formation of a more favorable energy offset at the titania/dye interface, and thereby leads to a faster electron injection rate and a higher exciton dissociation yield as implied by transient emission measurements. We also notice that the adverse influence of the titania conduction band edge downward shift arising from lithium addition upon photovoltage is partly compensated by a concomitant suppression of the triiodide involving interfacial charge recombination.     

Modified phthalocyanines for efficient near-IR sensitization of nanostructured TiO(2) electrode

A zinc phthalocyanine with tyrosine substituents (ZnPcTyr), modified for efficient far-red/near-IR performance in dye-sensitized nanostructured TiO(2) solar cells, and its reference, glycine-substituted zinc phthalocyanine (ZnPcGly), were synthesized and characterized. The compounds were studied spectroscopically, electrochemically, and photoelectrochemically. Incorporating tyrosine groups into phthalocyanine makes the dye ethanol-soluble and reduces surface aggregation as a result of steric effects. The performance of a solar cell based on ZnPcTyr is much better than that based on ZnPcGly. Addition of 3alpha,7alpha-dihydroxy-5beta-cholic acid (cheno) and 4-tert-butylpyridine (TBP) to the dye solution when preparing a dye-sensitized TiO(2) electrode diminishes significantly the surface aggregation and, therefore, improves the performance of solar cells based on these phthalocyanines. The highest monochromatic incident photo-to-current conversion efficiency (IPCE) of approximately 24% at 690 nm and an overall conversion efficiency (eta) of 0.54% were achieved for a cell based on a ZnPcTyr-sensitized TiO(2) electrode. Addition of TBP in the electrolyte decreases the IPCE and eta considerably, although it increases the open-circuit photovoltage. Time-resolved transient absorption measurements of interfacial electron-transfer kinetics in a ZnPcTyr-sensitized nanostructured TiO(2) thin film show that electron injection from the excited state of the dye into the conduction band of TiO(2) is completed in approximately 500 fs and that more than half of the injected electrons recombines with the oxidized dye molecules in approximately 300 ps. In addition to surface aggregation, the very fast electron recombination is most likely responsible for the low performance of the solar cell based on ZnPcTyr.     

N3-sensitized TiO2 films: in situ proton exchange toward open-circuit photovoltage enhancement

Protons of N3, cis-bis(thiocyanato)bis(2,2'-bipyridyl-4,4'-dicarboxylic acid)ruthenium(II), were in situ exchanged on N3-loaded TiO2 films with alkali-metal, tetrabutylammonium, and guanidinium cations. This simple strategy improved the open-circuit photovoltage (V(oc)) significantly, resulting in enhancement of the power conversion efficiency by 10-25%. Electrochemical impedance spectra revealed that the in situ proton exchange of the N3-loaded film suppressed charge recombination between injected electrons and I(3-) ions in the electrolyte, which, together with the negative shift of the conduction band edge for TiO2, may account for the remarkably increased V(oc) upon proton exchange of N3.     

Effect of coadsorbent on the photovoltaic performance of zinc pthalocyanine-sensitized solar cells

The effect of chenodeoxycholic acid as a coadsorbent on TiO 2 nanocrystalline solar cells incorporating phthalocyanine sensitizers was studied under various conditions. Adding chenodeoxycholic acid onto TiO 2 nanoparticles not only reduces the adsorption of phthalocyanine sensitizers but also prevents sensitizer aggregation, leading to different photovoltaic performance. The inspection of IPCE and absorption spectra showed that the load of phthalocyanine sensitizers is strongly dependent on the molar concentration of chenodeoxycholic acid coadsorbent. The open circuit voltage of the solar cells with chenodeoxycholic acid coadsorbent increases due to the enhanced electron lifetime in TiO 2 nanoparticles coupled with the band edge shift of TiO 2 to negative potentials.     

Interface modification effects of 4-tertbutylpyridine interacting with N3 molecules in quasi-solid dye-sensitized solar cells

In this paper, the interface modification effects of 4-tertbutylpyridine (TBP), especially the interaction with dye molecules, were discussed. The results of FTIR showed that TBP interacted with dye molecules, in addition to its interaction with the TiO(2) film. Reaction between N3 and TBP by the interaction force of the H atom in the -COOH group of N3 and the N atom of TBP could retard the aggregation of dye molecules, decreasing the electron quenching and charge recombination. Furthermore, the results of cyclic voltammograms and UV-vis absorption edge revealed the interaction between TBP and dye molecules could cause the energy level of the dye molecules to change, influencing the electron injection efficiency in DSCs. The IPCE results indicated that with TBP modification, the injection efficiency decreased, but the electron collection efficiency was enhanced.     

The influence of dye structure on charge recombination in dye-sensitized solar cells

Replacing the nonyl groups on the solar cell dye Ru(4,4'-carboxylic acid-2,2'-bipyridine)(4,4'-dinonyl-2,2'-bipyridine)(NCS)(2) (Z-907) with amino groups results in a marked decrease in solar cell performance. This is despite the fact that the amino derivative (Z-960) has more favourable light absorption characteristics than Z-907 when used with thick nanocrystalline TiO(2) layers. Electron transfer to the electrolyte from the exposed fluorine-doped tin oxide (FTO) substrate is particularly fast in cells employing the Z-960 dye if a compact TiO(2) blocking layer is not used. The kinetics of electron transfer from the nanocrystalline TiO(2) layer in DSCs employing Z-960 are comparable to those of bare TiO(2) and ca. 2 to 5 times faster than for cells employing Z-907. The faster charge recombination in cells employing Z-960 lowers open-circuit photovoltage and results in very significant charge collection losses that lower short-circuit photocurrent. Voltammetric measurements show that surface modification of FTO electrodes with Z-960 results in slightly more facile charge transfer to acceptor species in triiodide/iodide electrolytes in the dark. A simpler molecule, p-aminobenzoic acid, more dramatically catalyses this charge transfer reaction. Conversely, chemical modification of FTO electrodes with Z-907 or p-toluic acid retards charge transfer kinetics. Similar results are obtained for nanocrystalline TiO(2) electrodes modified with these benzoic acid derivatives. These results strongly imply that surface adsorbed molecules bearing amino groups, including dye molecules, can catalyse charge recombination in dye-sensitized solar cells.     

Characterization of solid-state dye-sensitized solar cells utilizing high absorption coefficient metal-free organic dyes

Solid-state dye-sensitized solar cells were fabricated using the organic hole-transporting medium (HTM) 2,2'7,7'-tetrakis-(N,N-di-p-methoxyphenyl-amine)-9,9'-spirobifluorene (spiro-MeOTAD), and three organic indoline-based sensitizer dyes with high molar extinction coefficients. The cells were characterized by several techniques, including spectral response measurements, photovoltage decay transients, intensity modulated photovoltage spectroscopy (IMVS), and charge extraction. The differences in apparent electron lifetime observed for cells fabricated using the three dyes are attributed in part to changes in the surface dipole potential at the TiO2/spiro-MeOTAD interface, which shift the TiO2 conduction band energy relative to the Fermi level of the HTM. These energy shifts influence both the open circuit voltage (as a result of changes in free electron density) and the short circuit current (as a consequence of changes in the overlap between the dye LUMO level and the conduction band). A self-consistent approach was used to derive the positions of the conduction band relative to the spiro-MeOTAD redox Fermi level for cells fabricated using the three dyes. The analysis also provided estimates of the free electron lifetime in spiro-MeOTAD cells. In order to evaluate the possible contribution of the adsorbed dyes to the observed changes in surface dipole potential, their dipole moments were estimated using ab initio density functional theory (DFT) calculations. Comparison of the calculated dipole contributions with the experimentally measured shifts in conduction band energy revealed that other factors such as proton adsorption may be predominant in determining the surface dipole potential.     

Phenoxazine dyes for dye-sensitized solar cells: relationship between molecular structure and electron lifetime

A series of metal-free organic dyes with a core phenoxazine chromophore have been synthesized and tested as sensitizers in dye-sensitized solar cells. Overall conversion efficiencies of 6.03-7.40% were reached under standard AM 1.5G illumination at a light intensity of 100 mW cm(-2) . A clear trend in electron lifetime could be seen; a dye with a furan-conjugated linker showed a shorter lifetime relative to dyes with the acceptor group directly attached to the phenoxazine. The addition of an extra donor unit, which bore insulating alkoxyl chains, in the 7-position of the phenoxazine could increase the lifetime even further and, together with additives in the electrolyte to raise the conduction band, an open circuit voltage of 800 mV could be achieved. From photoelectron spectroscopy and X-ray absorption spectroscopy of the dyes adsorbed on TiO(2) particles, it can be concluded that the excitation is mainly of cyano character (i.e., on average, the dye molecules are standing on, and pointing out, from the surface of TiO(2) particles).     

染料敏化太阳能电池中额外给体引入对经典D-π-A型敏化剂性能影响的理论研究

为了探讨D-D-π-A型染料中双给体对敏化剂性能的影响, 本文结合密度泛函理论(DFT)及含时密度泛函理论(TD-DFT)对染料1~4的几何结构、 电子结构、 吸收光谱、 电化学性质、 电子复合程度以及半导体导带边缘的移动等进行了对比研究. 结果表明, 相比于经典的D-π-A型染料分子1, 在分子2~4(D-D-π-A型双给体染料) 中额外引入给体, 尽管对导带能级移动的改变不是很显著, 但是可以改变体系的共轭程度, 增加染料的光吸收强度. 重要的是, 额外给体的引入可以显著增加染料阳离子空穴-半导体之间的距离, 从而减缓注入电子与染料阳离子的复合; 在额外给体中引入杂原子可以使I₂聚集在染料外侧, 从而降低电解质在半导体表面的局域浓度, 进而减缓注入电子与电解质之间的复合速率. 因此, 通过在经典的D-π-A型染料上引入额外的电子给体构筑D-D-π-A型染料可以有效调节染料的光吸收、 电化学及电子复合等方面的性质, 是设计合成高性能染料的可行策略.     

Photoinduced electron storage and surface plasmon modulation in Ag@TiO2 clusters

The reversible charging and discharging effects associated with photoexcitation of a TiO2 shell in a Ag@TiO2 composite are described. The photoinduced charge separation in the TiO2 shell is followed by electron injection into the silver core. Interestingly, the charging of the silver core is associated with the shift in the surface plasmon band from 460 to 430 nm. The stored electrons are discharged upon exposure of the charged Ag@/TiO2 composite to an electron acceptor. As the electrons from the silver core are discharged, the original surface plasmon absorption of the Ag core is restored.     

Photocatalysts of Cr Doped TiO2 Film Prepared by Micro Arc Oxidation

A series of Cr doped TiO2 films were prepared by micro arc oxidation (MAO) using an electrolyte of Na3PO4+K2Cr2O7. X-ray diffraction and scanning electron microscopy revealed that the films mainly consisted of anatase phase with a porous surface morphology. The films have an excellent photocatalytic effect for degradation of methylene blue and decomposition of water under visible light illumination. This arises from the formation of Cr3+/Cr4+ and oxygen vacancy energy levels owing to Cr doping. The former reduces the electron-hole recombination chance, while the latter generates a new gap between the conduction band (CB) and valence band (VB) of TiO2, which lowers the photo energy of the excited electron in the VB to the oxygen vacancy states. The mechanisms for film synthesis during the MAO process are also presented.     

Influence of 4-guanidinobutyric acid as coadsorbent in reducing recombination in dye-sensitized solar cells

Dye-sensitized solar cells based on nanocrystalline TiO(2) have been fabricated with an amphiphilic ruthenium sensitizer [Ru (4,4'-dicarboxylic acid-2,2'-bipyridine) (4,4'-bis(p-hexyloxystyryl)-2,2'-bipyridine)(NCS)(2)], coded as K-19, and 4-guanidinobutyric acid (GBA) as coadsorbent. The cells showed a approximately 50 mV increase in open-circuit voltage and a similar current in comparison with cells without GBA cografting. The performance of both types of devices was evaluated on the basis of their photocurrent-voltage characteristics, dark current measurements, cyclic voltammetry, electrochemical impedance spectroscopy, and phototransient decay methods. The results indicate that GBA shifted the conduction band of TiO(2) toward a more negative potential and reduced the interfacial charge-transfer reaction from conduction band electrons to triiodide in the electrolyte (also known as the back reaction). In addition, the devices with GBA cografting showed an excellent stability with a power conversion efficiency of approximately 8% under simulated full sunlight (air mass 1.5, 100 mW cm(-2)) during visible light soaking at 60 degrees C.