Thin-film nanocomposite forward osmosis membranes modified with Zr-based metal–organic framework to improve desalination performance

In present work, first, the water-stable metal–organic framework (MOF) nanocrystals, UiO-66-(F)₄, were synthesized under green reaction condition and then some PES/PA thin-film nanocomposite (TFN) membranes were prepared using this synthesized nanocrystals (as modifier) and polyethersulfone (as the substrate). The obtained MOF and membranes were characterized by various characterization techniques such as FE-SEM, AFM, PXRD, contact angle measurements and FT-IR spectroscopy. Finally, the forward osmosis performance of the resultant membranes was evaluated by using different concentrations of NaCl as a draw solution and deionized water as a feed solution. Among all used membranes, the membrane with 0.1 wt% loading of UiO-66-(F)₄ (TFN-2) was found to be an efficient composite membrane in the FO performance with high J_w and low J_s/J_w.     

Channel regulation of TFC membrane with hydrophobic carbon dots in forward osmosis

Zero-dimensional carbon dots have emerged as important nanofillers for the separation membrane due to their small specific size and rich surface functional groups. This study proposed a strategy based on hydrophobic carbon dots (HCDs) to regulate water channels for an efficient forward osmosis (FO) membrane. Thin-film composite (TFC) membranes with superior FO performance are fabricated by introducing HCDs as the nanofiller in the polyacrylonitrile support layer. The introduction of HCDs promotes the formation of the support layer with coherent finger-like hierarchical channels and micro-convex structure and an integrated polyamide active layer. Compared to the original membrane, TFC-FO membrane with 10 wt% HCDs exhibits high water flux (15.47 L m⁻² h⁻¹) and low reverse salt flux (2.9 g m⁻² h⁻¹) using 1 mol/L NaCl as the draw solution. This improved FO performance is attributed to the lower structural parameters of HCDs-induced water channels and alleviated internal concentration polarization. Thus, this paper provides a feasible strategy to design the membrane structure and boost FO performance.     

Preparation of sulfonated poly(phthalazinone ether sulfone ketone) composite nanofiltration membrane

Thin film composite (TFC) membranes were prepared from sulfonated poly(phthalazinone ether sulfone ketone) (SPPESK) as a top layer coated onto poly(phthalazinone ether sulfone ketone) (PPESK) ultrafiltration (UF) support membranes. The effects of different preparation conditions such as the SPPESK concentration, organic additives, solvent, degree of substitution (DS) of SPPEK and curing treatment temperature and time on the membrane performance were studied. The SPPESK concentration in the coating solution was the dominant factor for the rejection and permeation flux. The TFC membranes prepared from glycerol as an organic additive show better performance then those prepared from other additives. The rejection increased and the flux decreased with increasing curing treatment temperatures. The salt rejections of the TFC nanofiltration (NF) membranes increased in the order MgCl₂ < MgSO₄ < NaCl < Na₂SO₄. TFC membranes showed high water flux at low pressure. SPPESK composite membranes rejections for a 1000 mg L⁻¹ Na₂SO₄ feed solution was 82%, and solution flux was 68 L m⁻² h⁻¹ at 0.25 MPa pressure.     

Chitosan‐modified graphene oxide as a modifier for improving the structure and performance of forward osmosis membranes

Chitosan (CS) with good hydrophilicity and charged property was used to modify graphene oxide (GO), the obtained GO‐CS was used as a novel modifier to fabricate thin film composite forward osmosis (FO) membranes. The results revealed that the amino groups on CS reacted with carboxyl groups on GO, and the lamellar structure of the GO nanosheets was peeled off by CS, resulting in the reducing of their thicknesses. The GO‐CS improved the hydrophilicity of polyethersulfone (PES) substrate, and their contact angles decreased to 64° with the addition of GO‐CS in the substrate. GO‐CS also increased the porosity of the substrate and surface roughness of FO membrane, thereby optimizing the water flux and reverse salt flux of FO membrane. The average water flux of the FO membrane reached the optimal flux of 21.34 L/(m² h) when GO‐CS addition was 0.5 wt%, and further addition of GO‐CS to the substrate would decrease the water flux of FO membrane, and the reverse salt flux also decreased to the lowest value of 2.26 g/(m² h). However, the salt rejection of the membrane increased from 91.4% to 95.1% when GO‐CS addition increased from 0.5 to 1.0 wt% under FO mode using 1 mol/L sodium chloride (NaCl) solution as draw solution (DS). In addition, high osmotic pressure favored water permeation, and at the same concentration of DS, magnesium chloride (MgCl₂) exhibited better properties than NaCl. These results all suggested that GO‐CS was a good modifier to fabricate FO membrane, and MgCl₂ was a good DS candidate.     

Photocatalytic thin film composite forward osmosis membrane for mitigating organic fouling in active layer facing draw solution mode

As a high-flux operation mode of thin film composite-forward osmosis (TFC-FO) membrane, active layer facing draw solution (AL-DS) mode suffers from the severe membrane fouling tendency, which is not addressed well. Here, we introduced a photocatalyst (Anatase titanium dioxide, A-TiO₂) onto the support layer of TFC-FO membrane via the bonding of polydopamine (PDA) and polytetrafluoroethylene (PTFE), and prepared two photocatalytic membranes, A-TiO₂/PDA@TFC and A-TiO₂/PTFE@TFC. Compared with the pristine TFC-FO membrane, both A-TiO₂/PDA @TFC and A-TiO₂/PTFE@TFC had an improved water permeability (10.5 L m⁻²h⁻¹ and 9.5 L m⁻² h⁻¹, respectively) and reduced reverse NaCl flux salt (0.8 g m⁻² h⁻¹ and 0.7 g m⁻² h⁻¹, respectively) in the AL-DS mode using 1 mol/L NaCl as draw solution and pure water as feed solution. Moreover, in the 16 h fouling experiment using 200 ppm bovine serum albumin (BSA) solution as a representative pollutant, the flux decline rate of both photocatalytic membranes was dramatically alleviated from 39.7% and 21.7% in the darkness to 8.5% and 9.7% under UV irradiation, respectively, indicating a significant anti-fouling capacity of photocatalytic effect. In all, the presence of A-TiO₂ endowed membrane with high permeability, high rejection efficiency and excellent anti-fouling capacity under UV spotlight. As bonding agent, PTFE provided the modified membrane with a high photocatalytic effect and high self-cleaning capacity, while PDA increased the membrane permeability and protected membrane against photocatalytic damage. This work provides a simple and feasible method to improve the anti-fouling capacity of TFC-FO membrane in AL-DS mode.     

Study on preparation and performances of cellulose acetate forward osmosis membrane

Cellulose acetate (CA) forward osmosis (FO) membranes were prepared via a phase inversion process. CA was used as membrane material for FO. Acetone and 1,4-dioxane were employed as solvent. Polyvinylpyrrolidone (PVP), maleic acid, and methanol were applied as additives. An orthogonal experiment was performed to optimize the ratio of every component in the casting solution. The membrane with best performance was selected to concentrate an anthocyanin solution. Saturated sucrose solution (about 60°Brix) was fit for using as draw solution in the concentration experiment. Water flux, porosity, and rejection rate were measured to evaluate the membrane properties. Reverse water rinsing was used in cleaning membrane that was fouled by anthocyanin solution. Results showed that under membrane thickness of 100 μm, coagulation temperature at room temperature, and evaporation time of 30 s, the optimum components in casting solution were 13% CA, 45% 1,4-dioxane, 31% acetone, 2% maleic acid, 3% PVP, and 6% methanol. In the concentration experiment, the prepared FO membrane showed water flux of 2.04 L m^?2 h^?1 and rejection rate of 98.61%. In the membrane cleaning experiment, the water flux of the FO membrane recovered 87.51% after rinsing for 1 h. The prepared membranes and previously published membranes were compared which showed the prepared membrane could significantly improve the rejection rate for anthocyanin solution.     

木质素磺酸钠改性聚砜膜的制备及其在正渗透膜中的应用

采用木质素磺酸钠作为亲水添加剂,通过浸没沉淀相转化法制备了木质素磺酸钠共混改性聚砜膜,以改善聚砜膜的亲水性,并用作正渗透膜的支撑层,以降低内浓差极化效应.利用扫描电子显微镜、衰减全反射傅里叶变换红外光谱仪、水接触角仪等研究了不同木质素磺酸钠添加量对聚砜膜的结构和表面性质的影响.结果表明,添加木质素磺酸钠后,聚砜膜的指状孔变得规整且狭长.水接触角实验证实添加木质素磺酸钠能改善聚砜膜的亲水性,当木质素磺酸钠含量为0.4 wt%时,聚砜膜的表面水接触角可降低至65°.正/反渗透测试装置分别用于表征正渗透膜的传质性质和结构参数.结果表明,以0.4 wt%木质素磺酸钠改性聚砜膜为支撑层的正渗透膜的水渗透性能(A=3.12×10~(-5) LMH×Pa~(-1))优于纯聚砜基底正渗透膜(0.76×10~(-5)LMH×Pa~(-1)),而且前者的结构参数(S=2010mm)远小于后者(3450mm),说明木质素磺酸钠改性聚砜膜有效弱化了正渗透膜的内浓差极化效应.     

Study on a novel polyester composite nanofiltration membrane by interfacial polymerization of triethanolamine (TEOA) and trimesoyl chloride (TMC): I. Preparation, characterization and nanofiltration properties test of membrane

A novel thin-film composite (TFC) membrane for nanofiltration (NF) was developed by the interfacial polymerization of triethanolamine (TEOA) and trimesoyl chloride (TMC) on the polysulfone (PSf) supporting membrane. The active surface of the membrane was characterized by using FT-IR, XPS and SEM. The performance of TFC membrane was optimized by studying the preparation parameters, such as the reaction time of polymerization, pH of aqueous phase and the concentration of reactive monomers. It is found that the membrane performance is related to the changes of the monomer content in the aqueous phase rather than in the organic phase. Furthermore, the nanofiltration properties of the TFC membrane were tested by examining the separating performance of various salts at 0.6 MPa operating pressure. The rejection to different salt solutions decreased as per the order of Na₂SO₄ (82.2%), MgSO₄ (76.5%), NaCl (42.2%) and MgCl₂ (23%). Also, streaming potential tests indicated that isoelectric point of the TFC membrane is between pH 4 and 5. Moreover, the investigation of the flux for NaCl solution at different pH showed that the polyester NF composite membrane is also particularly suitable for treating acidic feeds: the flux increased from 8.4 to 11.5 L/m² h when pH of the feed decreased from 9 to 3. Additionally, the TFC membrane exhibits good long-term stability.     

Enhancing the performance of TFC nanofiltration membranes by adding organic acids in polysulfone support layer

Throughout this study, the effect of certain organic acids, methacrylic acid, lactic acid and tartaric acid, doped in polysulfone (PSF) casting solution onto the performance of nanofiltration (NF) membranes was investigated. Different NF membranes have been prepared from m-phenylenediamine and trimesoylchloride onto the top surface of the acid-modified PSF membranes through regulating the concentration and contact time of the conventional interfacial polymerization process. The study of scanning electron microscopy (SEM) was used to investigate the influence of acids on the morphology of membranes and cross-sectional structures. The functional groups, hydroxyl and carboxylic acid, of the acids have resulted in a significant increase in membrane thickness, porosity and hydrophilicity, with a decrease in macrovoid capacity of the PSF layer. The acid-modified PSF/TFC membranes showed higher rejection of salt, with an increment in water flux compared to the neat membrane. Water flux and salt rejection (R_s %) of the control membrane was 7.6 L/m² h and 65.4%, whereas polysulfone/methacrylic acid (PSF/MAAc), polysulfone/tartaric acid (PSF/TAc), and polysulfone/lactic acid (PSF/LAc) were 16.8, 18.5, and 20.2 L/m² h and 88, 88.2 and 94.1%, respectively. Efficiency of prepared NF membranes under various inlet pressures and specific salts was investigated with selectivity and salt rejection. The salt rejection of a mixed salt solution was found to meet the order of R_s % CaSO₄ ≥ R_s % Na₂SO₄ ˃ R_s % MgSO₄ ˃ R_s MgCl₂ ˃ Rs % NaCl.     

聚多巴胺/聚乙烯亚胺共沉积中间层增强薄膜复合正渗透膜性能

以聚多巴胺/聚乙烯亚胺(PDA/PEI)共沉积于三醋酸纤维素(CTA)多孔支撑膜表面形成中间层,再结合界面聚合法获得聚酰胺薄膜,构建了PDA/PEI共沉积中间层改性薄膜复合(TFC)正渗透(FO)膜.通过傅里叶变换衰减全反射红外光谱法、扫描电子显微镜、原子力显微镜、溶质截留法、水接触角仪等研究了PDA/PEI共沉积中间层对CTA膜和TFC膜的表面结构和性质的影响.研究结果表明,PDA/PEI共沉积使得CTA膜表面变得更为平滑,表面孔径减小至(30.0±4.1) nm,且表面孔径分布趋于均一.同时,在PDA/PEI共沉积改性CTA膜表面界面聚合得到的聚酰胺层呈现出更均匀的叶片状结构和优异的亲水性.基于此,具有PDA/PEI共沉积中间层的TFC正渗透膜显著提高了水通量(FO模式:(7.1±2.3) L/(m^2·h)),较空白TFC膜提升了57.6%.同时,中间层改性TFC膜具有更低的反向盐通量(FO模式:1.4±0.1 g/(m^2·h))和"净盐通量"(FO模式:(0.2±0.06) g/L),与空白TFC膜相比分别下降了83.9%和90.6%.说明PDA/PEI共沉积中间层不仅能有效提升TFC正渗透膜的水渗透性,而且大幅提升了膜的截盐性和渗透选择性.     

Power generation with pressure retarded osmosis: An experimental and theoretical investigation

Pressure retarded osmosis (PRO) was investigated as a viable source of renewable energy. In PRO, water from a low salinity feed solution permeates through a membrane into a pressurized, high salinity draw solution; power is obtained by depressurizing the permeate through a hydroturbine. A PRO model was developed to predict water flux and power density under specific experimental conditions. The model relies on experimental determination of the membrane water permeability coefficient (A), the membrane salt permeability coefficient (B), and the solute resistivity (K). A and B were determined under reverse osmosis conditions, while K was determined under forward osmosis (FO) conditions. The model was tested using experimental results from a bench-scale PRO system. Previous investigations of PRO were unable to verify model predictions due to the lack of suitable membranes and membrane modules. In this investigation, the use of a custom-made laboratory-scale membrane module enabled the collection of experimental PRO data. Results obtained with a flat-sheet cellulose triacetate (CTA) FO membrane and NaCl feed and draw solutions closely matched model predictions. Maximum power densities of 2.7 and 5.1 W/m² were observed for 35 and 60 g/L NaCl draw solutions, respectively, at 970 kPa of hydraulic pressure. Power density was substantially reduced due to internal concentration polarization in the asymmetric CTA membranes and, to a lesser degree, to salt passage. External concentration polarization was found to exhibit a relatively small effect on reducing the osmotic pressure driving force. Using the predictive PRO model, optimal membrane characteristics and module configuration can be determined in order to design a system specifically tailored for PRO processes.     

Separation of linear hydrocarbons and carboxylic acids from ethanol and hexane solutions by reverse osmosis

In this study, asymmetric cellulose acetate membranes with moderate NaCl rejection (85.5%) were prepared and used to study the influence of the chemical nature of organic solutes in different organic solvents. The solute rejection and the solvent flux of linear hydrocarbons (M_w=226–563 g/mol) and linear carboxylic acids (M_w=228–340 g/mol) in ethanol and hexane were studied as a function of the molecular weight, the feed concentration and the transmembrane pressure.The ethanol flux was three times higher than the hexane flux. The rejection coefficients for both types of solute were quire acceptable (R=60–90%), when ethanol was the solvent. In hexane the linear hydrocarbons showed a rejection of 40–60%, while all carboxylic acids reached a negative rejection of −40 to −20%. This negative “observed” rejection can be attributed to accumulation of carboxylic acid at the membrane; the solute concentration at the membrane becomes much higher than in the bulk solution, due to a higher affinity of the solute with the membrane in hexane than in ethanol. Sorption experiments support this hypothesis.Furthermore, it was found that the rejection increases with increasing molecular weight and the rejection and flux are hardly affected by the feed concentration.     

Interlaboratory studies of highly permeable thin‐film composite polyamide nanofiltration membrane

The aim of this paper is to survey interlaboratory studies of performance data to produce highly permeable thin‐film composite (TFC) polyamide nanofiltration (NF) membrane in the form of flat sheet at bench scale. TFC polyamide NF membranes were fabricated via interfacial polymerization of 1,3‐phenylenediamine and trimesoyl chloride on porous polyethersulfone (PES) membrane. The NF membranes were characterized by atomic force microscopy (AFM), scanning electron microscopy (SEM), and cross‐flow filtration. The AFM and SEM analyses indicated that a rough and dense film was formed on the PES support membrane. The permeability and NaCl rejection of the NF membrane prepared at the presence of camphor sulfonic acid as pH regulator and triethylamine as accelerator in the aqueous solution were 21 l m^?2 h^?1 and 70%, respectively. In order to estimate the repeatability and reproducibility standard deviations, the development of an interlaboratory study was conducted by measurements of permeation flux and salt rejection of the synthesized membranes. Repeatability standard deviation of the permeation flux data for the membrane based on optimum formulation was 1.99, and reproducibility standard deviation was 3.55. Also based on this trend, repeatability standard deviation of the salt rejection data was 1.57, and reproducibility standard deviation was 4.11. The American Society for Testing and Materials standard E691‐05 was used for data validation of the repeatability and reproducibility standard deviations and consistency statistics. Copyright © 2011 John Wiley & Sons, Ltd.     

High flux nanofiltration membranes based on interfacially polymerized polyamide barrier layer on polyacrylonitrile nanofibrous scaffolds

Electrospun polyacrylonitrile (PAN) nanofibrous scaffold was used as a mid-layer support in a new kind of high flux thin film nanofibrous composite (TFNC) membranes for nanofiltration (NF) applications. The top barrier layer was produced by interfacial polymerization of polyamides containing different ratios of piperazine and bipiperidine. The filtration performance (i.e., permeate flux and rejection) of TFNC membranes based on electrospun PAN nanofibrous scaffold was compared with those of conventional thin film composite (TFC) membranes consisting of (1) a commercial PAN ultrafiltration (UF) support with the same barrier layer coating and (2) two kinds of commercial NF membranes (i.e., NF90 and NF270 from Dow Filmtec). The nanofiltration test was carried out by using a divalent salt solution (MgSO₄, 2000 ppm) and a cross-flow filtration cell. The results indicated that TFNC membranes exhibited over 2.4 times more permeate flux than TFC membranes with the same chemical compositions, while maintaining the same rejection rate (ca. 98%). In addition, the permeate flux of hand-cast TFNC membranes was about 38% higher than commercial NF270 membrane with the similar rejection rate.     

Preparation,structure characteristics and separation properties of thin-film composite polyamide-urethane seawater reverse osmosis membrane

A novel thin-film composite (TFC) seawater reverse osmosis membrane was developed by the interfacial polymerization of 5-chloroformyloxyisophthaloyl chloride (CFIC) and metaphenylenediamine (MPD) on the polysulphone supporting membrane. The performance of the TFC membrane was optimized by studying the preparation parameters, which included the reaction time, pH of the aqueous-MPD solution, monomer CFIC concentration, additive isopropyl alcohol content in aqueous solution, curing temperature and time. The reverse osmosis performance of the resulting membrane was evaluated through permeation experiment with synthetic seawater, and the structure of the novel membrane was characterized by using SEM, AFM and XPS. Furthermore, the separation properties of the TFC membrane were tested by examining the reverse osmosis performances of various conditions, the boron rejection performance and the long-term stability. The results show that the desired TFC seawater reverse osmosis membrane has a typical salt rejection of 99.4% and a flux of about 35 L/m² h for a feed aqueous solution containing 3.5 wt.% NaCl at 5.5 MPa, and an attractive boron rejection of more than 92% at natural pH of 7–8; that the novel seawater reverse osmosis membrane appears to comprise a thicker, smoother and less cross-linking film structure. Additionally, the TFC membrane exhibits good long-term stability.     

Thermostable ultrafiltration and nanofiltration membranes from sulfonated poly(phthalazinone ether sulfone ketone)

Modification of poly(phthalazinone ether sulfone ketone) (PPESK) by sulfonation with concentrated or fuming sulfuric acid was carried out in order to prepare thermally stable polymers as membrane materials having increased hydrophilicity and potentially improved fouling-resistance. The sulfonated poly(phthalazinone ether sulfone ketone)s (SPPESK) were fabricated into ultrafiltration (UF) and nanofiltration (NF) asymmetric membranes. The effects of SPPESK concentration and the type and concentration of additives in the casting solution on membrane permeation flux and rejection were evaluated by using an orthogonal array experimental design in the separation of polyethyleneglycol (PEG12000 and PEG2000) and Clayton Yellow (CY, MW 695). One UF membrane formulation type had a 98% rejection rate for PEG12000 and a high pure water flux of 867 kg m⁻² h⁻¹. All the NF membranes made in the present study had rejections of ≥96%, and one had a high water flux of 160 kg m⁻² h⁻¹. Several of the NF membrane formulation types had ∼90% rejection for CY. When the membranes were operated at higher temperatures (80°C), the rejection rates declined slightly and pure water flux was increased more than two-fold. Rejection and flux values returned to previous values when the membranes were operated at room temperature again. Mono- and divalent salt rejections and fluxes were studied on an additional NF membrane set.     

Synthesis of organically bridged trialkoxysilanes bearing acetoxymethyl groups and applications to reverse osmosis membranes

New bridged trialkoxysilanes bearing acetoxymethyl groups were synthesized by double hydrosilylation of 1,6‐diacetoxy‐2,4‐butadiyne, using two equivalents of triethoxysilane and a metal catalyst. With a Ru catalyst, the reaction proceeded via anti‐addition to provide BTES‐Ac‐a as a single isomer, while a similar reaction with a Pt or Rh catalyst provided an isomeric mixture of syn ‐adducts BTES‐Ac‐b. Reverse osmosis (RO) silica membranes were prepared by the sol–gel process with BTES‐Ac‐a and BTES‐Ac‐b and the membranes were examined with respect to water desalination using a 2000 ppm NaCl aqueous solution. NaCl rejection of the membranes increased to reach 96% at the early stage of the RO experiments. However, the rejection decreased gradually to 85% after 70 and 200 h for BTES‐Ac‐a and BTES‐Ac‐b, respectively, due to hydrolytic decomposition of the silica network during the experiments. In contrast, a membrane prepared from copolymerization of BTES‐Ac‐a with ethane‐bridged bistrialkoxysilane (BTES‐E1) showed improved stability towards hydrolysis with stable NaCl rejection of 96% with higher water permeance (3.5 × 10⁻¹³ m³ m⁻² s⁻¹ Pa⁻¹) than that of a membrane prepared by homopolymerization of BTES‐E1 (2.7 × 10⁻¹⁴ m³ m⁻² s⁻¹ Pa⁻¹) reported previously.     

Mixed Polymer‐Coated Magnetic Nanoparticles as Forward Osmosis Draw Agents of Tuned Hydrophilicity

We recently reported a polymer‐coated magnetic nanoparticle (MNP) draw agent for the forward osmosis (FO) water desalination process. The water flux was found to increase when the polymer poly(sodium acrylate) (PSA) was anchored to the MNP surface as compared to the polymer (or polyelectrolyte solution) alone, due to the polymer chains being stretched out and most of the hydrophilic groups on the polymer contributing to water flux. We herein report the use of a secondary polymer poly(N‐isopropylacrylamide) PNIPAM to manipulate the PSA polymer conformation and influence inter‐ and intrachain interactions to enhance the efficiency of the FO draw agent. These PSA–PNIPAM‐coated MNPs generated a much higher water flux of ～11.66 LMH when compared to the 100 % PSA‐coated MNPs featuring a value of ～5.32 LMH under identical FO conditions. The osmotic pressure and water flux driven by the mixed polymer‐coated MNPs were found to be a strong function of the net polymer coverage on MNPs, that is, net available hydrophilic groups. Our new draw agent demonstrates potential for use in the water industry due to its improved efficiency and cost effectiveness as it uses only ～0.062 % (w/v) of the draw agent solution.     

Preparation and characterization of TiO2/Pebax/(PSf‐PES) thin film nanocomposite membrane for humic acid removal from water

New thin film composite (TFC) membrane was prepared via coating of Pebax on PSf‐PES blend membrane as support, and its application in wastewater treatment was investigated. To modify this membrane, hydrophilic TiO₂ nanoparticles were coated on its surface at different loadings via dip coating technique. The as‐prepared membrane was characterized using Fourier transform infrared spectroscopy, scanning electron microscopy (SEM), field emission SEM, and contact angle analysis. The Fourier transform infrared spectroscopy analysis and surface SEM images indicated that TiO₂ was successfully coated on the membrane surface. In addition, the results stated that the hydrophilicity and roughness of membrane surface increased by addition of TiO₂ nanoparticles. Performance of TFC and modified TFC membranes was evaluated through humic acid removal from aqueous solution. Maximum permeate flux and humic acid rejection were obtained at 0.03 and 0.01 wt% TiO₂ loadings, respectively. Rejection was enhanced from 96.38% to 98.92% by the increase of feed concentration from 10 to 30 ppm. Additionally, membrane antifouling parameters at different pressures and feed concentration were determined. The results indicated that surface modification of membranes could be an effective method for improvement of membrane antifouling property.     

Fabrication of Defect-Engineered MOF-801 Membrane for Efficient Dye Rejection

Although having shown great promise for efficient water treatment, rational structural design and engineering of polycrystalline MOF membranes remain rarely investigated so far. In this study, we prepared well-intergrown MOF-801 membranes with tailorable structural deficiencies in the framework for application in dye rejection. Of particular note, we found that the addition of formic acid as modulator led to the formation of MOF-801 membrane with higher missing-linker number, which was beneficial for increasing water flux with little compromise in dye rejection rate. The MOF-801 membrane prepared in this work exhibited excellent dye rejection performance (CR rejection rate of 99.50 % and water flux of 31.69 L m⁻² h⁻¹ bar⁻¹) as well as excellent long-term stability.